Determination of selenium in freshwaters by cathodic stripping voltammetry after UV irradiation

An analytical method was developed for the determination of total dissolved selenium in fresh waters, using linear sweep cathodic stripping voltammetry (CSV) in combination with UV photolytic digestion. Both the CSV method, based on the electrodeposition and stripping of Cu(2)Se, and the UV irradiation procedure were investigated in detail. In the presence of dissolved organic substances, as in freshwaters, Se(VI) is reduced to Se(IV) by UV irradiation in 0.1M hydrochloric acid. Glucose can be used as the carbon source in samples low in natural dissolved organic carbon (DOC). The photolytic yields of Se(IV) were about 90% in both cases. Five freshwater samples were analysed for total selenium by CSV after UV photolysis, and by hydride generation atomic absorption spectrometry (HG-AAS) after oxidative digestion followed by reduction with hydrochloric acid. The results agreed well and the concentrations were in the range 70-190 ng/l., well above the detection limit of the CSV method at 2 ng/l.     

Electrochemical vapor generation of selenium species after online photolysis and reduction by UV-irradiation under nano TiO<Subscript>2</Subscript> photocatalysis and its application to selenium speciation by HPLC coupled with atomic fluorescence spectrometry

An online UV photolysis and UV/TiO₂ photocatalysis reduction device (UV–UV/TiO₂ PCRD) and an electrochemical vapor generation (ECVG) cell have been used for the first time as an interface between high-performance liquid chromatography (HPLC) and atomic fluorescence spectrometry (AFS) for selenium speciation. The newly designed ECVG cell of approximately 115 L dead volume consists of a carbon fiber cathode and a platinum loop anode; the atomic hydrogen generated on the cathode was used to reduce selenium to vapor species for AFS determination. The noise was greatly reduced compared with that obtained by use of the UV–UV/TiO₂ PCRD–KBH₄–acid interface. The detection limits obtained for seleno-DL-cystine (SeCys), selenite (Se^IV), seleno-DL-methionine (SeMet), and selenate (Se^VI) were 2.1, 2.9, 4.3, and 3.5 ng mL^–1, respectively. The proposed method was successfully applied to the speciation of selenium in water-soluble extracts of garlic shoots cultured with different selenium species. The results obtained suggested that UV–UV/TiO₂ PCRD–ECVG should be an effective interface between HPLC and AFS for the speciation of elements amenable to vapor generation, and is superior to methods involving KBH₄.     

Critical evaluation of the application of photochemical vapor generation in analytical atomic spectrometry

Chemical vapor generation (CVG) is a widely adopted sample introduction method for analytical atomic spectrometry. Nonvolatile precursors (usually ionic, metallic or organometallic species) can be transferred from the condensed phase to the gas phase, yielding the advantages of efficient matrix separation, high analyte transport efficiency, high selectivity, simple instrumentation, and ease of automation. Hydride generation enjoys the greatest popularity as a consequence of its ease of implementation, fast reaction and high yield; but photo-CVG, a newly emerging research field in analytical chemistry, may provide a powerful alternative to conventional CVG due to its simplicity, versatility and cost effectiveness. Although photocatalytic pre-reduction has been used for a number of years, the most attractive aspect of this newly emerging area is the direct generation of volatile species using photochemical reactions. Recent studies undertaken with flow through and batch reactors employing low molecular weight organic acids as photochemical agents are highlighted in this study for such systems as mercury and selenium, as well as reaction mechanisms considered for these processes. Discussion is focused on recent advances in photo-CVG, which we believe will become the subject of intensive future research initiatives.     

Preconcentration and in-situ photoreduction of trace selenium using TiO2 nanoparticles, followed by its determination by slurry photochemical vapor generation atomic fluorescence spectrometry

We have developed a method for the determination of trace levels of total selenium in water samples. It integrates preconcentration, in-situ photoreduction and slurry photochemical vapor generation using TiO₂ nanoparticles, and the determination of total selenium by AFS. The Se(IV) and Se(VI) species were adsorbed on a slurry of TiO₂ nanoparticles which then were exposed to UV irradiation in the presence of formic acid to form volatile selenium species. The detection limits were improved 17-fold compared to hydride generation and 56-fold compared to photochemical vapor generation, both without any preconcentration. No significant difference was found in the limits of detection (LODs) for Se(IV) and Se(VI). The LOD is as low as 0.8 ng L^?1, the precision is better than 4.5 % (at a level of 0.1 μg L^?1 of selenium). The method gave good recoveries when applied to the determination of total selenium in a certified tissue reference material (DORM-3) and in spiked drinking water and wastewater samples containing high concentrations of transition and noble metal ions. It also excels by very low LODs, a significant enhancement of sample throughput, reduced reagent consumption and sample loss, and minimal interference by transition and noble metal ions.

Photochemical aging of secondary organic aerosol particles generated from the oxidation of d-limonene

Secondary organic aerosol (SOA) particles are generated by reacting d-limonene vapor and ozone in a Teflon reaction chamber. The reaction is carried out in either dry or humid air in darkness. The resulting SOA particles are collected on glass fiber filters, and their photochemical properties are probed using a combination of UV photodissociation action spectroscopy and absorption spectroscopy techniques. Photolysis of limonene SOA in the tropospheric actinic region (lambda > 295 nm) readily produces formic acid and formaldehyde as gas-phase products. The UV wavelength dependence of the photolysis product yield suggests that the primary absorbers in SOA particles are organic peroxides. The relative humidity maintained during SOA particle growth is found to have little effect on the UV wavelength dependence of the photolysis product yield. The data suggest that direct photodissociation processes may play an important role in photochemical processing of atmospheric SOA particles.     

A new vapor generation system for mercury species based on the UV irradiation of mercaptoethanol used in the determination of total and methyl mercury in environmental and biological samples by atomic fluorescence spectrometry

A new vapor generation system for mercury (Hg) species based on the irradiation of mercaptoethanol (ME) with UV was developed to provide an effective sample introduction unit for atomic fluorescence spectrometry (AFS). Preliminary investigations of the mechanism of this novel vapor generation system were based on GC–MS and FT–IR studies. Under optimum conditions, the limits of determination for inorganic divalence mercury and methyl mercury were 60 and 50 pg mL⁻¹, respectively. Certified reference materials (BCR 463 tuna fish and BCR 580 estuarine sediment) were used to validate this new method, and the results agreed well with certified values. This new system provides an attractive alternative method of chemical vapor generation (CVG) of mercury species compared to other developed CVG systems (for example, the traditional KBH₄/NaOH–acid system). To our knowledge, this is the first systematic report on UV/ME-based Hg species vapor generation and the determination of total and methyl Hg in environmental and biological samples using UV/ME–AFS. Figure A new vapor generation system for mercury species using mercaptoethanol under UV irradiation was developed as an effective sample introduction unit for atomic fluorescence spectrometry     

Photochemical behavior of inorganic and organic selenium compounds in various aqueous solutions

Selenium possesses interesting chemical, biochemical and geochemical behaviors. However, studies of its photochemical properties in aqueous systems are scarce. A better understanding of these phenomena is of great importance for further application of such properties to selenium speciation. In this work, the photochemical behavior of selenium and some of its organic compounds have been systematically studied in various aqueous matrices under UV irradiation at 300 nm. It was observed that the photochemical oxidation rate of Se(IV) to Se(VI) was greatly enhanced in the presence of HN0₃ at ≥1 × 10⁻³ M, but not by NaNO₃. However this photo-oxidation could be inhibited by the presence of Cl⁻. Under UV irradiation, organoselenium compounds went through two successive photochemical reactions in pure water: a direct photolysis (photo-cleavage) followed by a photo-oxidation to form Se(VI). These two steps could also be greatly accelerated in presence of NO₃⁻ although the second step required an acidic condition. The photo cleavage rates varied from one organic compound to another and 10-fold differences were observed. Similarly to Se(IV), the further oxidation to Se(VI) could be prevented by Cl⁻ for all studied organoselenium compounds. Detailed reaction mechanisms involving OH radicals are proposed to explain Se photochemical behaviors in different matrices.     

Photochemical vapor generation of selenium: Mechanisms and applications

Selenium was the first reported element that could be converted into its volatile compounds via photochemical vapor generation (photo-CVG) process before its atomic spectrometric detection. Photo-CVG is a newly emerging vapor generation technique, offering its inherent advantages of matrix interferences eliminated and high vapor efficiency etc., photo-CVG has been combined with various methods for selenium determination and mechanism exploration. Herein, we summarize the development of selenium in photo-CVG from the first report in 2003, the mechanisms of selenium with or without TiO₂ were discussed and its applications for selenium determination, speciation analysis and prereduction were summarized.     

大米中硒含量的测定

为使人们更好地控制和调节硒的摄入量,用紫外分光光度法测定了大米中的硒含量。样品通过混酸消化,将有机硒转化成无机硒,酸性条件下,Se(Ⅳ)与邻苯二胺反应,产物在335nm有最大吸收峰。测定结果表明,天津小站米、东北米、丝苗米、泰国香米、富硒米的有机硒含量分别为:0.041、0.046、0.035、0.034、2.021μg/g,有机硒含量占总硒含量的比例分别是89.13%、82.14%、87.50%、80.95%、98.92%。富硒米硒含量及有机硒的比例明显高于其它种类的米。     

Mild generation of 5-(2'-deoxyuridinyl)methyl radical from a phenyl selenide precursor

[reaction: see text] 5-(2'-Deoxyuridinyl)methyl radical (1) resulting from formal hydrogen atom abstraction from the methyl group of thymidine is produced from the respective phenyl selenide precursor (2) via 350 nm photolysis or mild thermolysis (37 degrees C in the presence of glutathione) under aerobic or anaerobic conditions. The mild thermal generation of a nucleoside radical provides an alternative to previously reported photochemical methods, which are not always compatible with nucleic acids.     

紫外光诱导化学蒸气发生-氩/氢火焰原子荧光光谱法测定丹参中硒

以紫外光诱导化学蒸气发生装置作为原子荧光光谱仪的进样系统,建立了光化学蒸气发生原子荧光光谱法测定中药材丹参中总硒含量的分析方法。研究了试剂浓度、光化学蒸气反应管等因素对硒化学蒸气发生效率的影响。仪器对硒的检出限为6.60 ng/mL,精密度(RSD)为0.6%(n=10),回收率为98%～107%。     

Ultraviolet Photolysis and Ortho-Phthalaldehyde-Mercaptoethanol Derivatization of Pharmaceuticals for Enhanced Fluorescence Detection in HPLC

Abstract

Several classes of nitrogenous pharmaceutical were examined for fluorescence after ultraviolet (UV) radiation induced photolysis followed by reaction with o-phthalaldehyde-2-mercaptoethanol (OPA-MERC), and after UV photolysis alone. Photolyses were examined in water, mixtures of methanol/water (1:1), and acetonitrile/water (1:1). Acetone was assessed as a photosensitizer to enhance photolysis and fluorescence response. Flow injection analysis and high-performance liquid chromatographic techniques were used for several pharmaceuticals. The analytes were subjected to UV photolysis and reaction with OPA-MERC reagent for generation of fluorophores that responded to fluorescence detection. During photolysis, solvent type as well as the presence of photosensitizers seem to play a significant role in the formation of primary amines and fluorophores. Photochemical transformation products of some of the pharmaceutical chemicals are proposed. Analytical figures of merit were determined for some analytes. This fluorescence detection approach is applicable for a number of pharmaceuticals at nanogram level.     

Photochemical aging of α-pinene secondary organic aerosol: effects of OH radical sources and photolysis

This study addresses photochemical aging of secondary organic aerosol (SOA) produced from α-pinene ozonolysis. The SOA is aged via hydroxyl radical (OH) reactions with first-generation vapors and UV photolysis. OH radicals are created through tetramethylethylene ozonolysis, HOOH photolysis, or HONO photolysis, sources that vary in OH concentration and the presence or absence of UV illumination. Aging strongly influences observed SOA mass concentrations, but the behavior is complex. In the dark or with high concentrations of OH, vapors are functionalized, lowering their volatility, resulting in an increase in OA by a factor of 2-3. However, with lower concentrations of OH under UV illumination SOA mass concentrations decrease over time. We attribute this decrease to evaporation driven by photolysis of the highly functionalized second-generation products. The photolysis rates are rapid, a few percent of the NO(2) photolysis frequency, and can thus be highly competitive with other aging mechanisms in the atmosphere.     

Interference by Desferrioxamine of Spin Trapping Oxy-Radicals For ESR Analysis

Abstract

The iron chelator desferrioxamine (DEF), commonly used to assess the involvement of iron in oxy-radical production, was examined with respect to its effect on spin trapping oxy-radicals generated independently of iron. OH. was generated by photolysis of H₂O₂- was generated by photolysis of Cds dispersions and by the hypoxanthine-xanthine oxidase system.In the presence of DEF, the amount of the radicals detected by spin trapping techniques of ESR with 5,5-dimethyl-1-pyrroline-1-oxide was greatly diminished. These results confirmed that DEF is an oxy-radical scavenger and, in addition, indicated that it should not be used to assess the involvement of iron in oxy-radical generation during spin trapping with nitrones for ESR analysis.

An additional finding was that a new radical, as yet uncharacterized, was generated by UV irraditional of DEF.     

UV photochemical vapor generation-atomic fluorescence spectrometric determination of conventional hydride generation elements

A systematic investigation of UV photochemical vapor generation (photo-CVG) and its potential application for seven typical hydride-forming elements (As, Sb, Bi, Te, Sn, Pb and Cd) when combined with atomic fluorescence spectrometry (AFS) detection is presented. These analyte ions were converted to volatile species following UV irradiation of their aqueous solution to which low molecular weight organic acids (such as formic, acetic or propionic acid) had been added, and introduced to an atomic fluorescence spectrometer for subsequent analytical measurements. The experimental conditions for photo-CVG and the interferences arising from concomitant elements were carefully investigated. Limits of detection as low as 0.08, 0.1, 0.2 and 0.5 ng mL^− 1 were obtained for Te, Bi, Sb and As, respectively, comparable to those by hydride generation-AFS. The RSDs obtained with the proposed method for these elements were better than 5% at 50 ng mL^− 1. It is noteworthy that the presence of TiO₂ nanoparticles combined with UV irradiation remarkably enhances the CVG efficiencies of Se(VI) and Te(VI), which cannot form hydrides with KBH₄/NaBH₄. Moreover, photo-CVG has a greater tolerance toward interferences arising from transition elements than hydride generation, and this facilitates its application to the analysis of complicated sample matrices.     

The effects of water vapor on the CH3O2 self-reaction and reaction with HO2

The gas phase reactions of CH3O2 + CH3O2, HO2 + HO2, and CH3O2 + HO2 in the presence of water vapor have been studied at temperatures between 263 and 303 K using laser flash photolysis coupled with UV time-resolved absorption detection at 220 and 260 nm. Water vapor concentrations were quantified using tunable diode laser spectroscopy operating in the mid-IR. The HO2 self-reaction rate constant is significantly enhanced by water vapor, consistent with what others have reported, whereas the CH3O2 self-reaction and the cross-reaction (CH3O2 + HO2) rate constants are nearly unaffected. The enhancement in the HO2 self-reaction rate coefficient occurs because of the formation of a strongly bound (6.9 kcal mol(-1)) HO2 x H2O complex during the reaction mechanism where the H2O acts as an energy chaperone. The nominal impact of water vapor on the CH3O2 self-reaction rate coefficient is consistent with recent high level ab initio calculations that predict a weakly bound CH3O2 x H2O complex (2.3 kcal mol(-1)). The smaller binding energy of the CH3O2 x H2O complex does not favor its formation and consequent participation in the methyl peroxy self-reaction mechanism.     

Photoassisted vapor generation in the presence of organic acids for ultrasensitive determination of Se by electrothermal-atomic absorption spectrometry following headspace single-drop microextraction

A method is described for the determination of selenium at the pg/mL level by electrothermal-atomic absorption spectrometry using in situ photogeneration of Se vapors, headspace sequestration onto an aqueous microdrop containing Pd(II) and subsequent injection in a graphite tube. Several organic acids (formic, oxalic, acetic, citric and ethylenediaminetetraacetic) have been tried for photoreduction of Se(IV) into volatile Se compounds under UV irradiation. Experimental variables such as UV irradiation time, organic acid concentration, Pd(II) concentration in the drop, sample and drop volumes, extraction time and pH were fully optimized. Low-molecular weight acids such as formic and acetic provided optimal photogeneration of volatile Se species at a 0.6 mol/L concentration. Citric and ethylenediaminetetraacetic acid allowed to use a concentration as low as 1 mmol/L, but extraction times were longer than for formic and acetic acids. Photogeneration of (CH₃)₂Se from Se(IV) in the presence of acetic acid provided a detection limit of 20 pg/mL, a preconcentration factor of nearly 285 and a precision, expressed as relative standard deviation, of 4%. Analytical performance seemed to depend not only on the photogeneration efficiency obtained with each acid but also on the stability of the vapors in the headspace. The method showed a high freedom from interferences caused by saline matrices, but interferences were observed for transition metals at a relatively low concentration.     

Photolytic processing of secondary organic aerosols dissolved in cloud droplets

The effect of UV irradiation on the molecular composition of aqueous extracts of secondary organic aerosol (SOA) was investigated. SOA was prepared by the dark reaction of ozone and d-limonene at 0.05-1 ppm precursor concentrations and collected with a particle-into-liquid sampler (PILS). The PILS extracts were photolyzed by 300-400 nm radiation for up to 24 h. Water-soluble SOA constituents were analyzed using high-resolution electrospray ionization mass spectrometry (HR-ESI-MS) at different stages of photolysis for all SOA precursor concentrations. Exposure to UV radiation increased the average O/C ratio and decreased the average double bond equivalent (DBE) of the dissolved SOA compounds. Oligomeric compounds were significantly decreased by photolysis relative to the monomeric compounds. Direct pH measurements showed that acidic compounds increased in abundance upon photolysis. Methanol reactivity analysis revealed significant photodissociation of molecules containing carbonyl groups and the formation of carboxylic acids. Aldehydes, such as limononaldehyde, were almost completely removed. The removal of carbonyls was further confirmed by the UV/Vis absorption spectroscopy of the SOA extracts where the absorbance in the carbonyl n→π* band decreased significantly upon photolysis. The effective quantum yield (the number of carbonyls destroyed per photon absorbed) was estimated as ～0.03. The total concentration of peroxides did not change significantly during photolysis as quantified with an iodometric test. Although organic peroxides were photolyzed, the likely end products of photolysis were smaller peroxides, including hydrogen peroxide, resulting in a no net change in the peroxide content. Photolysis of dry limonene SOA deposited on substrates was investigated in a separate set of experiments. The observed effects on the average O/C and DBE were similar to the aqueous photolysis, but the extent of chemical change was smaller in dry SOA. Our results suggest that biogenic SOA dissolved in cloud and fog droplets will undergo significant photolytic processing on a time scale of hours to days. This type of photolytic processing may account for the discrepancy between the higher values of O/C measured in the field experiments relative to the laboratory measurements on SOA in smog chambers. In addition, the direct photolysis of oligomeric compounds may be responsible for the scarcity of their observation in the field.     

New Indicator Reactions Involving Sulfur-Containing Organic Compounds for the Kinetic Determination of Selenium

New indicator reactions were proposed for the determination of selenium by the kinetic method based on the reduction of Methylene Blue by some sulfur-containing organic compounds. It was demonstrated that a high sensitivity of the determination of selenium is attained using unithiol and thiomalic, 2,3-dithiomercaptopropionic, and rubeanic acids as reducing agents. In the presence of unithiol, down to 4 ng/mL selenium can be determined.     

Water as a clustering agent in photolysis and photonucleation of benzaldehyde vapor

The role of water vapor in benzaldehyde photolysis and photonucleation is investigated experimentally as well as with the help of semiempirical estimation of reaction intermediates. It is shown that water molecules act as a clustering agent that brings together two benzaldehyde molecules. This mechanism may explain the experimental observation of glyoxal formation during photolysis in humid carrier gas even in the presence of oxygen, the dependence of the concentrations of glyoxal and diphenyl on water-vapor concentration, and some other unusual facts concerning minor products detected in the experiment.