Characterization of stoichiometric LiNbO3 grown from melts containing K2O

The growth of LiNbO₃ single crystals from a melt with the Li/Nb ratio of 0.946, to which 6 wt.% K₂O has been added, leads to stoichiometric specimens, essentially free of potassium, with (50±0.15) mol% Li₂O in the crystal. This is established by studying the composition dependence of the following properties: linewidths of the electron paramagnetic resonance (EPR) of Fe³⁺, energy of the fundamental absorption edge, Raman linewidths of phonon modes, and dispersion of the optical birefringence. Comparison of the results with relevant calibration scales leads to the above composition. In all cases the Li₂O content was found to be closer to 50% than that of a LiNbO₃ crystal vapor-phase equilibrated to 49.9mol% Li₂O. The photorefractive effect at light intensities I10⁷ W/m² is suppressed in this stoichiometric material. The features of the ternary system K₂O-Li₂O-Nb₂O₅, which are possibly responsible for the unexpected growth of stoichiometric LiNbO₃ from the indicated melts, are discussed.     

Electrochemical behavior of Li intercalation processes into a Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 cathode

Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (X=0.17, 0.25, 0.33, 0.5) compounds are prepared by a simple combustion method. The Rietvelt analysis shows that these compounds could be classified as having the α-NaFeO₂ structure. The initial charge-discharge and irreversible capacity increases with the decrease of x in Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂. Indeed, Li[Ni_0.50Mn_0.50]O₂ compound shows relatively low initial discharge capacity of 200 mAh/g and large capacity loss during cycling, with Li[Ni_0.17Li_0.22Mn_0.61]O₂ and Li[Ni_0.25Li_0.17Mn₀.₅₈]O₂ compounds exhibit high initial discharge capacity over 245 mAh/g and stable cycle performance in the voltage range of 4.8 -2.0 V. On the other hand, XANES analysis shows that the oxidation state of Ni ion reversibly changes between Ni²⁺ and about Ni³⁺, while the oxidation state of Mn ion sustains Mn⁴⁺ during charge-discharge process. This result does not agree with the previously reported ‘electrochemistry model’ of Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂, in which Ni ion changes between Ni²⁺ and NI⁴⁺. Based on these results, we modified oxidation-state change of Mn and Ni ion during charge-discharge process.     

石墨/Li（Ni1/3Co1/3Mn1/3）O2电池充放电过程中电极材料的XRD研究

利用XRD系统地研究了石墨/Li（Ni_1/3Co_1/3Mn_1/3）O₂ 18650型锂离子电池充放电过程中正负极活性材料的晶体结构和微结构的变化.已观测到,由于Li原子的脱嵌,使得LiMO₂点阵参数a缩小,c增大,微应变增大,衍射强度比I₁₀₄/I₁₀₁和I₀₁₂/I₁₀₁降低;此外,由于Li原子的嵌入,2H-石墨的点阵参数a和c,以及微应变ε和堆垛无序度P都增加.同时,讨论了活性材料Li（Ni_1/3Co_1/3Mn_1/3）O₂和石墨在电池充放电过程中的嵌脱锂的物理机理.在充电时,正极Li（Ni_1/3Co_1/3Mn_1/3）O₂中处于（000）位的Li原子优先脱离晶体点阵,继后才是位于（2/3 1/3 1/3）和（1/3 2/3 2/3）位的Li原子离开点阵.锂嵌入石墨,优先进入碳原子六方网格面间的间隙位置,当负极的堆垛无序度达到一定值后,3R相逐渐析出.当电池满充或过充时,在六方石墨中形成LiC₁₂和LiC₆相.放电时,与上述过程相反,但并非是完全可逆的. 关键词： 锂离子电池 微结构 X射线衍射 嵌脱锂物理机理     

Successive phase transitions in the highly ordered complex perovskite PbLu1/2Nb1/2O3

The structural phase transitions and the electrical behaviour of the complex perovskite PbLu_1/2Nb_1/2O₃ have been investigated using X-ray powder diffraction, dielectric constant measurements, differential scanning calorimetry and measurement of the polarisation as a function of applied electric field. The high-temperature paraelectric phase is highly ordered. A first-order paraelectric-antiferroelectric phase transition occurs at 270°C and an antiferroelectric-ferroelectric phase transition, characterised by dispersion in the curves of dielectric constant as a function of temperature, occurs at ≈ 30°C. The antiferroelectric phase is isostructural with the orthorhombic form of PbYb1/₂Nb1/₂O₃. The low-temperature ferroelectric phase also has an orthorhombic crystal structure.     

Effect of Hydrostatic Pressure on the Dielectric Response of Pb(Mg1/3Nb2/3)O3 Relaxor

The effect of hydrostatic pressure on the dielectric response of Pb(Mg_1/3Nb_2/3)O₃ relaxor single crystal was studied. An increase in the dispersion of the dielectric anomaly, characteristic of the relaxors, was observed: pressure-induced downward shift of the temperature T _m of permittivity maximum at 1 kHz amounts to dT _m /dp = ? 3.8 K/100 MPa, whereas that measured at 1 MHz equals ? 3.3 K/100 MPa. Analysis of the dielectric response of the highly polarizable Pb(Mg_1/3Nb_2/3)O₃ shows that hydrostatic pressure results in a decrease of the correlation radius r _c of polar nanodomains, as well as their activation energy.     

Effect of milling time on the properties of Pb(Mg1/3Nb2/3)O3 ceramics using the starting precursors PbO and MgNb2O6

Lead magnesium niobate, Pb(Mg_1/3Nb_2/3)O₃ (PMN) ceramics were prepared from the columbite method using calcined powders of various milling time (24–96 h). The effects on the grain size and dielectric properties of the ceramics were investigated. The results show that dielectric properties of ceramics are strongly influenced by the milling time of the starting precursors. Higher percentage of perovskite phase was found in the ceramics that was milled longer and thus the dielectric constant was found to increase when compared to the conventional 24 h milled results. Moreover, milling time also affected the particle size of the starting precursors and that of PMN powders. Therefore, milling time did not only affect the particle size of PMN powders but also the resultant grain size and the formation of perovskite phase, consequently affecting the dielectric constant of the ceramics.     

Secondary-Phase Formation in Spinel-Type LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>-Cathode Materials for Lithium-Ion Batteries: Quantifying Trace Amounts of Li<Subscript>2</Subscript>MnO<Subscript>3</Subscript> by Electron Paramagnetic Resonance Spectroscopy

Spinel-type lithium manganese oxides are considered as promising cathode materials for lithium-ion batteries. Trace amounts of Li₂MnO₃ usually occur as a secondary phase in lithium-manganese spinels in the common high-temperature, solid-state synthesis, affecting the overall Li–Mn stoichiometry in the spinel phase and thereby the electrochemical performance. However, the formation of Li₂MnO₃ lower than 1 wt.% can hardly be quantified by the conventional analytical techniques. In this work, we synthesized lithium-manganese spinels with different Li/Mn molar ratios and demonstrate that electron paramagnetic resonance (EPR) enables quantifying trace amounts of Li₂MnO₃ below 10^?2 wt.% in the synthesized products. The results reveal that the formation of Li₂MnO₃ secondary phase is favored by lithium excess in the synthesis. Based on the quantitative evaluation of the EPR data, precise determining Li–Mn stoichiometry in the spinel phase in Li_1+xMn_2?xO₄ materials can be assessed. Accordingly, it is possible to estimate the amount of lithium on 16d-sites in the Li-rich manganese spinels.     

Dielectric properties of solid solutions PbMg1/3Nb2/3O3-SrTiO3

Ceramic samples of the solid solutions PbMg_1/3Nb_2/3O₃-SrTiO₃ are synthesized. The dielectric properties are studied and a phase diagram is constructed. The results obtained are discussed in terms of ideas concerning relaxor ferroelectrics for solid solutions on the PMN side and from the standpoint of potential ferroelectrics on the SrTiO₃ side. The introduction of SrTiO₃ into PMN gradually degrades relaxor properties, and the introduction of PMN into SrTiO₃ does not result in initiation of the ferroelectric phase transition, possibly because of the appearance of random fields in the lattice. The possibility of practical applications of the synthesized system is also discussed. Fiz. Tverd. Tela (St. Petersburg) 41, 1091–1095 (June 1999)     

Li2O-(LiCl)2-B2O3-Al2O3系统玻璃的Raman光谱研究

我们用Raman光谱研究了Li₂O(LiCl)₂B₂O₃-Al₂O₃系玻璃的结构,着重研究了Al₂O₃的影响。对于Li₂O-B₂O₃系玻璃,Li₂O含量增加使玻璃中存在的BO₃三角体转变为BO₄四面体, 关键词：     

Synthesis and characterization of nanostructured Li2MnO3 from nanostructured MnOOH precursors

Li₂MnO₃ with different nanostructures was synthesized through a solid-state reaction. MnOOH nanorods and nanowires prepared via the hydrothermal method were used as precursors, respectively, to react with Li(OH)·H₂O to prepare nanostructured Li₂MnO₃ in the temperature range from 500 to 800 °C. The samples were characterized by XRD, TEM, ESR and FTIR results. Based on the experimental results, the dehydration-oxidation-combination (DOC) formation mechanism of Li₂MnO₃ was proposed.     

Facile preparation and performance of novel high-TC xBi(Ni1/2Ti1/2)O3-(1-x)Pb(Zr1/2Ti1/2)O3 piezoceramics

High Curie temperature (T_C) xBi(Ni_1/2Ti_1/2)O₃-(1-x)Pb(Zr_1/2Ti_1/2)O₃ (xBNT-(1-x)PZT, BNT-PZT) piezoelectric ceramics were prepared by the conventional ceramic processing. The composition-induced morphotropic phase boundary (MPB) and its influences on structure and electrical performance were investigated. The synthesized BNT-PZT ceramics exhibit rather pure perovskite structure, and densified microstructure morphology with uniform elementals distribution in both grains and grain boundaries. With increasing the content of Bi(Ni_1/2Ti_1/2)O₃ (BNT), crystal structure of the BNT-PZT ceramics transform from tetragonal phase to rhombohedral phase, and dielectric response peaks change from narrow shape to very broad shape but all presenting dielectric frequency dispersion. The diffused and relaxation dielectric behavior can be fitted well by the quadratic law, and the Vogel-Fulcher law fitting provides additional information on the relaxation characteristic. The MPB effects are confirmed further by ferroelectric and piezoelectric properties measurements. High-T_C combined with excellent piezoelectric performance can be realized in the BNT-PZT system, which presents promising applications in geothermal exploration, aerospace and related elevated temperatures fields.     

Dielectric relaxation in the weak ferroelectric Li2Ge7O15 near the ferroelectric phase transition

The dielectric permittivity of Ni-doped Li₂Ge₇O₁₅ crystals was studied in the vicinity of the ferroelectric phase transition. Introduction of Ni has been shown to suppress the dielectric anomaly and to reduce substantially the transition temperature. A temperature hysteresis in ɛ (T) has been observed in nominally pure and Ni-doped Li₂Ge₇O₁₅ crystals near the transition point. Measurements performed under cooling from the paraphase reveal dispersion of dielectric permittivity at Debye relaxation frequencies of the order of 10⁴–10⁵ Hz at T _c . It is proposed that the hysteresis phenomena and the low-frequency dispersion are caused by residual defects (of the type of random local fields), which become polarized in the ferroelectric phase and become disordered above T _c . Fiz. Tverd. Tela (St. Petersburg) 40, 2198–2201 (December 1998)     

An anomalous enhancement in the electrical conductivity of Li2O : B2O3 : Al2O3 glasses

The study of electrical conductivity of 27.5 Li₂O : (72.5 − x) B₂O₃ : x Al₂O₃ glass samples has been carried out. It has been observed that the conductivity exhibits Arrhenius behavior for all samples up to glass transition temperature T_g. Beyond T_g, an anomalous enhancement followed by decrease in conductivity has been observed. The results have been explained by dividing the temperature range into two regions. In region-I, it has been observed that the conductivity variation exhibits a maximum at 2.5 mol% Al₂O₃, which has been explained on the basis of Mixed Glass Former Effect (MGFE). An anomalous enhancement in the conductivity observed in region-II has been attributed to the nucleation in the glass. The subsequent decrease in the conductivity has been attributed to the crystallization of the glass samples.     

Structural and electrochemical study on Li(Li1/3Ti5/3)O4 anode material for lithium ion batteries

Chemical and electrochemical studies have shown that various titanium oxides can incorporate lithium in different ratios. Other compounds with a spinel-type structure and corresponding to the spinel oxides LiTi₂O₄ and Li₄Ti₅O₁₂ have been evaluated in rechargeable lithium cells with promising features. The spinel Li[Li_1/3Ti_5/3]O₄ [1–5] compound is a very appealing electrode material for lithium ion batteries. The lithium insertion-deinsertion process occurs with a minimal variation of the cubic unit cell and this assures high stability which may reflect into long cyclability. In addition, the diffusion coefficient of lithium is of the order of 10⁻⁸ cm²s⁻¹ [5] and this suggests fast kinetics which may reflect in high power capabilities. In this work we report a study on the kinetics and the structural properties of the Li[Li_1/3Ti_5/3]O₄ intercalation electrode carried out by: cyclic voltammetry, galvanostatic cycling and in-situ X-ray diffraction. The electrochemical characterization shows that the Li[Li_1/3Ti_5/3]O₄ electrode cycles around 1.56 V vs. Li with a capacity of the order of 130 mAhg⁻¹ which approaches the maximum value of 175 mAhg⁻¹ corresponding to the insertion of 1 equivalent per formula unit. The delivered capacity remains constant for hundred cycles confirming the stability of the host structure upon the repeated Li insertion-deinsertion process. This high structural stability has been confirmed by in situ Energy Dispersion X-ray analysis. Paper presented at the 7th Euroconference on Ionics, Calcatoggio, Corsica, France, Oct. 1–7, 2000.     

E-T phase diagrams of a solid solution of the multicomponent PbZn1/3Nb2/3O3-PbMg1/3Nb2/3O3-PbNi1/3Nb2/3O3-PbTiO3 system near the morphotropic phase boundary

The specific features of the dielectric and pyroelectric responses of a solid solution in the barium-doped multicomponent yPbZn_1/3Nb_2/3O₃-mPbMg_1/3Nb_2/3O₃-nPbNi_1/3Nb_2/3O₃-xPbTiO₃ system of the composition y = 0.0982, m = 0.4541, n = 0.1477, and x = 0.3 near the morphotropic phase boundary have been investigated. It has been assumed that the maxima revealed in the dependences of the reversible permittivity on the electric field strength with both the forward and backward changes in the field (E ₌) are associated with the induced phase transition. Based on the experimental results, the E-T phase diagrams are constructed in the temperature range from ?100 to 150°C for different temperature-field regimes: (i) variation in the electric field E ₌ at a fixed temperature of the sample and (ii) variation in the temperature of the sample at a constant value of E ₌. It has been found that there is a singular point in the E-T phase diagram and that, in the vicinity of this point, the dielectric and pyroelectric responses of the studied ceramics exhibit specific features.     

PEO-based composite lithium polymer electrolyte, PEO-BaTiO3-Li(C2F5SO2)2N

Polyethylene oxide (PEO) based polymer electrolytes with BaTiO₃ as filler and Li(C₂F₅SO₂)₂N as salt have been examined in lithium polymer batteries. The aluminum disolution potential in PEO-Li(C₂F₅SO₂)₂N was estimated to be 4.1 V vs. Li/Li⁺ at 80 °C, which was compared to that of 3.8 V vs. Li/Li⁺ in PEO-Li(CF₃SO₂)₂N. The electrical conductivity of the system was measured as a function of O/Li ratio. The highest conductivity was observed in O/Li=8. The conductivity was 1.65×10⁻³ S/cm at 80 °C and 1.5×10⁻⁵ S/cm at 25 °C. The interfacial resistance of Li/polymer electrolyte/Li annealed at 80 °C for 15 days was lower than 100 Ωcm². Paper presented at the 8th EuroConference on Ionics, Carvoeiro, Algarve, Portugal, Sept. 16 – 22, 2001.     

Laser-diode-excited Blue Upconversion in Tm3+/Yb3+-codoped TeO2-Ga2O3-R2O (R=Li, Na, K) Glasses

This paper reports on intense blue upconversion in Tm³⁺/Yb³⁺ codoped TeO₂-Ga₂O₃-R₂O(R=Li, Na, K) glasses upon excitation with commercial available laser diode (LD). Effects of alkali ions on the Raman spectra, thermal stability and spectroscopic properties of the tellurite-gallium glasses have also been investigated. Energy transfer and the involved upconversion mechanisms have been discussed. Intense blue upconversion emission centered at 476 nm along with a weak red emission at 650 nm has been observed upon excitation of 977 nm LD, assigned to the transitions of , and and/or of Tm³⁺, respectively. The blue upconversion intensity has a cubelike dependence on incident pump laser power, indicating a three-photon process. However, a quadratic dependence of the 476 nm upconversion intensity on the incident pump laser power has been observed when samples under excitation of 808 nm LD due to a two-photon absorption process. Enhanced upconversion luminescence have been observed with replacing K⁺ for Na⁺ and Li⁺.     

Structural,magnetic and dielectric properties of (Li1+, Al3+) co-doped Ni0.5Zn0.5Fe2O4 ferrite ceramics prepared by the sol-gel auto-combustion method

(Li¹⁺, Al³⁺) co-doped Ni_0.5Zn_0.5Fe₂O₄ ferrites, Ni_0.5-xZn_0.5-xLi_xAl_xFe₂O₄ (x = 0.000, 0.025, 0.050 and 0.100), were synthesized by the sol-gel auto-combustion method. X-ray diffraction (XRD), field emission scanning electronic microscope (FESEM), vibrating sample magnetometer (VSM) and LCR meter were used to investigate the structural, magnetic and dielectric properties. Results of XRD and SEM indicate that both doping amount and calcination temperature play significant roles in crystal structure and grain growth. Also, it can be observed that the saturation magnetization and the coercivity change in a noticeable manner. The Ni_0.475Zn_0.475Li_0.025Al_0.025Fe₂O₄ ferrite sintered at 1200 °C has a relatively low coercivity value (62.93 Oe) and the largest saturation magnetization (110.95 emu/g). Besides, dielectric behavior is also improved by Li¹⁺ and Al³⁺ co-doping.     

Lithium ions conduction in Li2xMn1-xPS3 films

Li_2xMn_1-xPS₃ films have been synthesized by exfoliating MnPS₃ through the successive intercalations of K⁺ and Li⁺ ions. Their dielectric response has been measured from 80 to 350 K in the frequency range of (10²–10⁶) Hz. The obtained data have been analyzed in terms of both complex permittivity ε* and the ac conductivity σ_ac. The frequency dependence of σ_ac has been interpreted in terms of the Jonscher’s law, whose exponent n decreases by increasing temperature. The n values lie between 0.479 and 0.501 and are typical of materials in which the ac conductivity is due to multiple hops of carriers. By analyzing the σ_dc temperature dependence, the observed dielectric response has been attributed to the intercalated lithium ions, and the Li_2xMn_1-xPS₃ films have been classified as hopping charge carrier systems.     

Thermoluminescence of B2O3-Li2O glass system doped with MgO

Lithium borate (LiB) glasses in the system (100−x)B₂O₃-xLi₂O with x=20, 30, 40, 50, 60 and 70 mol% were prepared. The glasses were doped with different concentrations of the order of 10⁻¹, 10⁻², 10⁻³, 10⁻⁴ and 10⁻⁵ of MgO and their thermoluminescent (TL) response was investigated. The irradiations were performed using γ rays from a ⁶⁰Co source in the dose range from 0.1 to 25 kGy. The material displayed good sensitivity for γ-rays and intensity of TL signals is dependent on γ-ray dose and Li₂O content. For each dose level and investigated temperature range (50-350 °C), exactly single isolated glow peak appears in the temperature range of 165-205 °C depending on both Li₂O concentrations and time of exposure. The shape of the glow peak has altered significantly with increase in the gamma ray dose or Li₂O concentrations. The glass composition with x=50 mol% doped with 10⁻³ mol% of MgO presented the best TL response. The results of the present study indicated that the recorded single and isolated high temperature peak is a good candidate for TL dosimetric investigations. This indicates that 50 B₂O₃-50Li₂O-doped with 10⁻³ mol% of MgO is possibly used as materials for radiation dosimetry in the dose range of 0.1-20 kGy.