DSC study of precipitation in an Al-Mg-Mn alloy microalloyed with Cu

Power compensation differential scanning calorimetry (DSC) has been employed to detect and analyse precipitation reactions in an Al-1.3Mg-0.4Mn and an Al-1.3Mg-0.4Mn-0.07Cu alloy in which very small amounts of precipitate, less than 0.3 at.%, are expected to form. Due to the very small heat effects, baseline instability and drift significantly interfere with the measurements. After repeated experiments and careful baseline correction it is demonstrated that in the Cu containing alloy, ageing at 170 °C causes the appearance of two endothermic effects: for 2 days ageing a small dissolution effect appears at about 230 °C, whilst for 7 and 21 days ageing a dissolution effect peaking appears at about 300 °C. The temperature range of the latter is consistent with S phase dissolution.     

Cross-linking assessment after accelerated ageing of ethylene propylene diene monomer rubber

The ageing of filled and cross-linked ethylene propylene diene elastomer (EPDM) has been studied under accelerated UV irradiation (λ ≥ 290 nm) at 60 °C, thermal ageing at 100 °C and in nitric acid vapours for different time intervals. Hardness measurements were performed. DSC-thermoporosimetry was used to estimate the mesh size distribution and cross-linking densities for each ageing. The development of functional groups was monitored by ATR spectroscopy. An increase in oxidation with exposure time after the different types of ageing was observed. The thermal stability of EPDM was assessed by TGA and evolved volatile gases were identified using FTIR spectroscopy.     

DSC study of glycerol-extracted muscle fibers in intermediate states of ATP hydrolysis

Summary The heat capacity of contractile proteins actin and myosin was studied in psoas muscle of rabbit in strongly and weakly binding state of myosin to actin as a function of temperature by DSC. Deconvolution of the unfolding scans makes possible to characterize the structural domains of the macromolecules. We tried to approach the unfolding process in different intermediate state of ATP hydrolysis. The thermal transitions were calorimetrically irreversible, therefore the two-state irreversible model that describes fairly well the denaturation of different proteins was used for evaluation of the denaturation processes in muscle fibers in strongly (rigor, ADP) and weakly binding states (ATP·V_i, ADP·AlF₄) of myosin to actin. Deconvolution resulted in four transitions, the first three transition temperatures were almost independent of the intermediate states of muscle, the last transition temperature was shifted to higher temperature, when the buffer solution was manipulated. The mean values in strongly binding states were T_m1=52.9±0.7°C, T_m2=57.9±0.7°C, T_m3=63.7±1.0°C and T_m4=67.8±0.7°C, but the last transition increased to higher temperature depending on the P_i analogue.     

Radioimmunoassay of Human Follicle Stimulating Hormone /HFSH/

A method for determining Human FSH in blood/serum by RIA is described. The radioiodination of FSH with¹²⁵I is carried out under carefully controlled conditions such as, amount of initial activity of¹²⁵I take for iodination, the reaction volume, and the reaction time, etc. The tracer FSH obtained thus is with minimum damage and optimum specific activity which is ideally suited for RIA. The shelf-life of the tracer is enhanced by the addition of benzyl alchol. The tracer can be conveniently stored at+4–6°C upto 10 weeks, avoiding the repeated freezing and thawing process. Antiserum to FSH is raised in rabbits by repeated injections via intramuscular route. The method utilizes polyethylene glycol /PEG/ as the separation system. Using this method, a number of control samples of men and women of reproductive age group are screened. This sensitive assay has a good validity and has an inter-assay variation less than 15%.     

Accelerated ageing due to moisture absorption of thermally cured epoxy resin/polyethersulphone blends. Thermal, mechanical and morphological behaviour

A model epoxy resin/anhydride system, modified with a polyethersulfone (PES) engineering thermoplastic toughening agent, has been studied under hydrothermal ageing in order to investigate the modification of the thermal, morphological and mechanical behaviour through dynamical mechanical thermal analysis, SEM microscopy and fracture toughness test respectively. Two different concentrations of the toughening agent were used in the blends and two ageing conditions have been considered, consisting of the immersion of the samples in distilled water at constant temperature of 70 °C for 1 week and for 1 month. Dynamical mechanical thermal analysis results on hydrothermally aged materials indicated the occurrence of progressive segregation effects with the formation of regions with different cross-linking degrees.Fracture toughness tests showed an increase of the K_IC value with the increase of the toughening agent concentration, revealing both a dramatic decrease of the same parameter after 1 week ageing for all the materials and the tendency to reach an almost constant value after 1 month ageing for all the formulations, with a slight increase with respect to 1 week ageing. These results have been interpreted on the basis of the SEM analysis, showing the presence of a well defined micrometric PES particles distribution in the epoxy/anhydride matrix, and discussed in the light of different water absorption mechanisms at short and long ageing times.     

Thermal, ozone and gamma ageing of styrene butadiene rubber and poly(ethylene-co-vinyl acetate) blends

Ageing behaviour of SBR/EVA blends due to the effects of heat, ozone, and gamma radiation was studied with reference to blend ratio, three crosslinking systems (sulfur, peroxide and mixed) and a compatibiliser (SEBS-g-MA). It was found that an increase in the EVA content of the blends enhanced the ageing characteristics. Among the different crosslinking systems, a peroxide cured system exhibited the best retention of properties even after severe ageing. Tensile strength of peroxide cured SBR/EVA blends increased slightly after ageing for three days at 70 °C due to continued crosslinking, whereas tensile strength of all blends decreased on ageing at 100 °C. Compatibilisation with SEBS-g-MA improved the thermal, gamma and water ageing resistance of SBR/EVA blends.     

Ageing mechanism and mechanical degradation behaviour of polychloroprene rubber in a marine environment: Comparison of accelerated ageing and long term exposure

Polymers are widely used in marine environments due to their excellent properties and good weathering resistance. Despite this extensive use, their long term behaviour in such an aggressive environment is still not well known. To assess the polymer durability within reasonable durations, it is essential to perform accelerated ageing tests to accelerate the degradation kinetics but without any modification of the degradation process. This study therefore proposes and validates accelerated ageing tests to study marine ageing of a silica-filled chloroprene rubber (CR) used for offshore applications. Several accelerated ageing protocols are investigated for temperatures ranging from 20 to 80 °C in renewed natural seawater. The ageing consequences are characterized using physical measurements (FTIR, solid state NMR) and mechanical testing based on monotonic tension tests. Instrumented micro-indentation tests are also employed, in order to describe accurately the ageing gradients through sample thickness. The measurements obtained on the samples cut from accelerated specimens are compared to those obtained from the topcoat of an offshore flowline aged under service conditions for 23 years. For both kinds of specimens, polychloroprene develops rapid material changes most clearly represented by a considerable increase in stiffness, which allows the accelerated ageing protocols to be validated.     

Energy resolution of liquid scintillator for α-particles and internal conversion electrons at lower temperatures

The energy resolution of -particles from²⁴¹Am,²²²Rn,²¹⁸Po and²¹⁴Po and internal conversion electrons from^131mXe with a liquid scintillation system has been studied at temperatures from 13 °C to –65 °C. At lower temperatures the liquid scintillation system has shown to give better energy resolutions both for -particles and internal conversion electrons compared with the values obtained at ordinary temperature. The phenomena were explained by the increase in light output of liquid scintillator at lower temperatures.     

Thermal ageing of rocket propellant formulations containing ε-HNIW (ε-CL20) investigated by heat generation rate and mass loss

New types of rocket propellant batches have been formulated with the objective of achieving higher burning rates. The main ingredients are (1) the energetic plasticizers glycidyl azide polymer-α,ω-diazide (GAP)-A (short chain GAP with azide end groups), trimethylolethane trinitrate (TMETN) and 1,2,4-butanetriol trinitrate (BTTN), (2) the energetic substances ammonium perchlorate (AP) and ε-CL20 (ε-HNIW, hexanitrohexazaisowurtzitane, crystallised in ε-phase). The binder is GAP (glycidyl azide polymer, diol component) cured with the polyisocyanate Desmodur™ N100. From the point of view of stability and ageing, the interesting fact is that the formulations contain none of the typical stabilisers for the nitric acid ester components TMETN and BTTN, although their contents range up to 21 mass%. One reason for doing so is to increase the content of the high energy ingredients. Seven formulations were examined in more detail. To assess basic stability the autoignition temperature test, Dutch mass loss test and vacuum stability test were used. To investigate ageing, two measurement quantities are applied: heat generation rate (heat flow) as function of time at 70, 80 and 89 °C and mass loss as function of time at the temperatures of 70, 80 and 90 °C. The evaluation of the measurements was done with reaction kinetic models. One batch (#189) containing BTTN shows significantly lower activation energy and pre-exponential factor. From mass loss one gets as activation energy for #189 of 101 kJ mol⁻¹ in comparison to the range of 126-135 kJ mol⁻¹ for the six other batches. But, based on the ageing caused by chemical decomposition reactions, all seven batches showed a good ageing behaviour. A use time period of up to 20 years of use seems realistic.     

Studies on the ageing of a magnesium-strontium nitrate pyrotechnic composition using isothermal microcalorimetry and thermal analysis techniques

The ageing behaviour of a pyrotechnic composition containing equal parts by mass of magnesium and strontium nitrate has been followed by isothermal microcalorimetry. The measurements were carried out on the samples at 50 °C and 65% relative humidity in air using closed ampoules. The results have been compared to those obtained for magnesium powder under the same conditions. Following an initial induction period, the pyrotechnic compositions reacted at a much faster rate than magnesium powder alone. The main reaction products were found to be magnesium hydroxide and strontium nitrite; the amounts formed have been correlated with the cumulative heats of ageing. In addition, the influence of the ageing process on the pyrotechnic reaction has been studied by high temperature differential scanning calorimetry (DSC) and by modulated temperature DSC.     

Assessing the progress of degradation in polyurethanes by chemiluminescence and thermal analysis. II. Flexible polyether- and polyester-type polyurethane foams

The thermooxidative and thermal stability of polyether- and polyester-type polyurethane foams were investigated by non-isothermal chemiluminescence (CL), differential scanning calorimetry (DSC) and thermogravimetry (TG). In the presence of air and humidity, the effect of various routes and conditions of polyurethane ageing (induced thermally or by light) on the chemiluminescence, DSC and thermogravimetry patterns was assessed. The rate constants determined from non-isothermal thermogravimetry and chemiluminescence measurements at 250 °C and their not very pronounced dependence on the atmosphere of degradation indicated that depolymerisation of the polyurethane containing the aliphatic polyester and aromatic polyisocyanate moieties preceded or occurred in parallel with thermal oxidation. Under conditions of 50% relative humidity, samples of the polyester-type polyurethane, aged either by light or thermally, as well as specimens of the polyether-type polyurethane, aged by light, gave increased amounts of carbonaceous residue when heated in nitrogen to 550 °C.     

Radiotracer investigation of phosphoric acid and phosphatic fertilizers production process

In the phosphoric acid production process, the time a particle spends inside the chemical reactor (residence time) is of paramount importance to process engineers. Residence time distribution (RTD) gives information on the efficiency of the chemical reactor, on the efficiency of the process, and also the availabilities of the reactive volume for the reaction (active volume vs. dead volume). Traditionally, chemical engineers used chemical tracer to determine the RTD. However, first disadvantage is that the chemical tracer could not allow an online diagnosis: the samples containing chemical tracer have to go to a lab for analysis, second disadvantage is that the chemical tracer is less sensitive than radioactive ones because of its adsorption onto strata or its retention in rocks. Consequently, chemical tracer results are not always precise and cannot convincingly explain the multiple flow-path model. Radioactive tracers are the only tracers capable of measuring the active RTD with high degree of precision and give information on the internal recirculation rate. In this work, we will describe the application of radiotracer method for RTD measurement in the phosphoric acid production process and give results and discussion of each case encountered.     

Coupled tracer diffusion coefficients of solubilizates in ionic micelle solutions from liquid chromatography

The peak-broadening (Taylor dispersion) method is used to measure the diffusion of traces of alcohols (ethanol, n-butanol, n-hexanol, n-octanol, n-decanol) in aqueous solutions of sodium dodecylsulfate micelles at 25°C. A small quantity of each alcohol is injected into a long capillary tube containing a laminar stream of the micelle solution. The tracer diffusion coefficient is calculated from the broadened distribution of the eluted alcohol which is measured by differential refractometry. The fraction of each alcohol that is solubilized by the micelles is estimated from the drop in the diffusion coefficient relative to the value for the free alcohol molecules in pure water. The refractive index profiles across the dispersed samples are analyzed to obtain the cross-diffusion coefficient which gives the coupled flow of sodium dodecylsulfate produced by the tracer diffusion of each alcohol.     

Tracer diffusion of Co2+ ions in multielectrolyte systems: Activation energy and obstruction effect

The activation energy for the tracer diffusion of Co²⁺ ions in multielectrolyte systems containing alkali bromides has been determined in agar gel medium over the temperature range of 25–45°C. The decrease in the value of the Arrhenius parameters, E and D_o, with gel percentage is explained on the basis of the transition state theory. Further, studies of the influence of electrolyte concentration on activation energy and obstruction effect reveal that both parameters decrease with the former. The decrease in activation energy is explained by considering the changes in physical properties of the solution with concentration at microscopic level, while the decrease in the extent of obstruction effect is attributed to competitive hydration between ions and agar molecules in a diffusion system.     

A Novel Attempt to Calculate the Velocity Correlation Coefficients in Ternary Electrolyte Solution

This work gives estimated values of the velocity correlation coefficients VCCs for ternary electrolyte solutions (the system may have a tracer ion as one of the components), utilizing available measured transport coefficients. The VCCs originate from linear response theory and give a deeper insight into the microdynamic structure of complex ionic solutions. By assuming Onsager’s relation to be valid, ten sets of velocity correlation coefficients were calculated for a ternary system and were used to calculate the VCCs for ¹³⁴Cs⁺ ion (present in trace amount) transport in aqueous solutions of CsCl and KCl at 25^○C.     

Partial molal volumes of ions in organic solvents. IV. Ethylene glycol

Apparent molal volumes have been measured for several electrolytes in ethylene glycol (EG) and the standard state partial molal volumes, V₂°, evaluated. Ultrasonic vibration potentials (uvp) have also been measured for most of the alkali metal halides in EG, and these employed to evaluate ionic partial molal volumes, V° (ion). The results show unambiguously that the uvp is essentially independent of solvent viscosity. The V₂° data have also been divided into ionic components by four other techniques including, the method of Mukerjee, the use of Ph₄AsBPh₄, the correspondence method and an extrapolation of V₂° for a series of tetraalkylammonium bromides as a funtion of cation molecular weight. With the exception of the latter technique, all methods used give 30±2 cm³-mol^–1 for V° (ion), although the uvp leads to the largest value for V° (ion). The divisions have been analyzed also with the aid of Hepler's equation, and the results suggest that the uvp method gives a more accurate division and that the EG dipole is more hindered than the dipole in ethanol.     

On the use of catalysis to bias reaction pathways in out-of-equilibrium systems

Catalysis is an essential function in living systems and provides a way to control complex reaction networks. In natural out-of-equilibrium chemical reaction networks (CRNs) driven by the consumption of chemical fuels, enzymes provide catalytic control over pathway kinetics, giving rise to complex functions. Catalytic regulation of man-made fuel-driven systems is far less common and mostly deals with enzyme catalysis instead of synthetic catalysts. Here, we show via simulations, illustrated by literature examples, how any catalyst can be incorporated in a non-equilibrium CRN and what their effect is on the behavior of the system. Alteration of the catalysts'' concentrations in batch and flow gives rise to responses in maximum conversion, lifetime (i.e. product half-lives and t90 – time to recover 90% of the reactant) and steady states. In situ up or downregulation of catalysts'' levels temporarily changes the product steady state, whereas feedback elements can give unusual concentration profiles as a function of time and self-regulation in a CRN. We show that simulations can be highly effective in predicting CRN behavior. In the future, shifting the focus from enzyme catalysis towards small molecule and metal catalysis in out-of-equilibrium systems can provide us with new reaction networks and enhance their application potential in synthetic materials, overall advancing the design of man-made responsive and interactive systems.

We show, via simulations, how catalytic control over individual paths in a fuel-driven non-equilibrium chemical reaction network in batch or flow gives rise to responses in maximum conversion, lifetime and steady states.     

Preliminary study of UV ageing process of proteinaceous paint binder by FT-IR and principal component analysis

This work presents a preliminary study on the ageing process of proteinaceous binder materials used in painting under UV light. With this aim, two sets of model samples were prepared: samples prepared using a single protein material and complex samples prepared in a similar way to the sequence of layers in a real painting from lowest to highest complexity (protein, drying oils, pigment and varnish). The study focuses on acquiring information about the possible degradation process of proteinaceous binders due to ageing and how this process be affected by the presence of characteristic non-proteinaceous painting materials, such as lipids from linseed oil, terpenic compounds from varnish and inorganic pigments. Samples simulated the accelerated ageing process, as did the UV light exposition. The FT-IR spectra were recorded after 100, 500, 1000 and 1500 h of exposition. The study of the accelerated ageing process was performed by means of principal component analysis (PCA) using the FT-IR spectra obtained. Loadings from the significant principal components were analysed to find the FT-IR frequency (cm⁻¹) involved in the degradation process. The study showed the lack of any relevant modification on the proteins in the single model samples. On the contrary, the complex model samples showed the ageing process. The accelerated ageing process can be explained by a principal component from PCA. The most affected IR region was 2900-3600 cm⁻¹, where the amide band was included.