高功率横流CO2激光器脉冲预电离过程研究

本文给出了对高功率横流CO_2激光器脉冲预电离过程的理论和实验研究.表明了预电离过程中光电离的重要作用.实验结果表明,脉冲预电离可增大高功率横流CO_2.激光器的pd值(p为放电气压、d为放电间隔),增大放电区注入功率密度.对于提高此类型激光器的放电稳定性和输出激光功率是一种技术简单而有效的手段.     

工业多用途工具：微波激励KW级CO2激光器

提高气体放电的功率注入密度，是进一步发展工业用高功率ＣＯ２激光器的关键．为此，我们采用自制的变形 Ｍａｇｉｃ Ｔ型微波放电腔，克服了由于高频趋肤效应引起的放电不均匀，实现了大体积的均匀的微波辉光放电．在用于激励高功率ＣＯ２激光的原理性实验中，获得大于１ｋｗ的激光输出功率，光电效率优于２５％，首次达到商用水平．     

TEA CO2激光器不同放电电路放电过程的比较

 利用像增强CCD相机对脉冲CO₂激光器的放电区进行观测,获得了放电辉光的发展过程,由此研究了长脉冲放电电路和短脉冲放电电路对放电过程的影响。发现普通电容放电电路（长脉冲放电电路）存在与自持放电阶段相对应的二次辉光;采用磁压缩开关的短脉冲放电电路,预电离出现较晚,但预电离辉光峰值和主放电辉光峰值之间间距较短,不存在自持放电阶段,只观测到一次强辉光。长脉冲放电电路与短脉冲放电电路在放电的后期均存在一个阴极位降区形成的过程。短脉冲放电电路有利于产生更窄的脉宽和更高的峰值功率。     

10μm超短脉冲激光系统

具有新颖表面电晕预电离单模ＴＥＡＣＯ２激光器，等离子体开关和热吸池的光学自由诱导衰变（ＯＦＩＤ）激光系统产生３０－３００ｐｓ１０．６μｍ激光。     

预电离脉冲群开关技术高功率脉冲CO2激光器

采用独特的电极结构和预电离脉冲群开关放电技术,实现了5kW量级平均功率横流CO2激光器脉冲激光输出.     

预电离脉冲群开关技术高功率脉冲CO2激光器

采用独特的电极结构和预电离脉冲群开关放电技术, 实现了5kW 量级平均功率横流CO₂激光器脉冲激光输出. 关键词： 2脉冲激光')" href="#">CO₂脉冲激光 预电离 脉冲群开关     

脉冲CO2激光器峰值功率的增益饱和现象

从理论和实验的角度分析了在腔损耗调制状态下,当调制速度与ＣＯ２激光转动能级间的驰豫速度相当时,激光器输出脉冲峰值功率与增益系数间存在的非线性特性：峰值功率随增益系数的增加,存在饱和现象。这种特性是ＣＯ２Ｂ类激光器的特点,实验和理论模拟结果一致。     

TEACO2激光器中气体组分对放电状态的影响

采用自制实时取样系统及四极质谱仪测量ＴＥＡＣＯ２激光器放电过程中气体组分变化，分析了测量结果对ＴＥＡＣＯ２激光器放电状态的影响。     

侧面预电离氟化氪激光器研制

采用侧面紫外火花隙自动预电离代替小极上小孔预电离，使放电泵浦氟化氪激光器的主放电均匀性大为改善。输出激光能量由１４０ｍＪ提高到２５０ｍＪ，增益区光能密度为２．３Ｊ／１，同时电极寿命和气体寿命也大为提高。     

阻抗自调控CO2激光器电源

本文介绍一种采用阻抗自调控限流电路的ＣＯ２激光器电源，它可使ＣＯ２激光器的输出激光功率从零到满功率大范围连续可调，能得到小纹波甚至无纹波的激光束．     

放电引发的非链式高功率重复频率HF/DF激光器

高功率重频HF/DF激光因其具有的波长和功率优势成为当前中红外激光技术发展的热点之一。介绍了利用紫外预电离横向放电结构和工作气体循环系统建立的放电引发高功率重频HF/DF激光装置。在对激光工作介质SF6/C2H6混合气体放电特性和激光输出特性研究的基础上,开展了强电负性气体的重频均匀体放电技术和气体快速循环置换技术研究,解决了泵浦源重频放电能量在气体介质中的有效沉积和提取问题,实现了激光器50Hz的重频稳定运行和能量稳定输出,HF激光的平均功率达到28W,脉宽100ns,峰值功率5.6 MW。     

Characteristics of a Cataphoresis He-Ca+ Recombination Laser

A cataphoretic input of calcium vapour into the active volume of pulsed He-Ca^＋ laser is designed and made. The recombination laser at 373.3 nm and the R-M transition laser at 854.6 nm are achieved experimentally with modified Blumlein circuit by high-frequency longitudinal pulsed discharge. The dependences of work parameters such as the pulse frequency, the power supply voltage and the helium pressure on laser output characteristics at 373.3nm line are measured and discussed. The maximum laser output power of 136mW and the specific power of 5.9 m W/cm^3 are obtained, respectively.     

Generation of a uniform high-density microwave plasma for CO2 lasers using orthogonal electric fields

To realize a CO₂ laser using a fast-axial-flow high-output-power microwave discharge excitation, we devised a technology for making the microwave discharge uniform by varying the oscillation direction of an electric field with time. We also verified the effectiveness of this technology. As a result, we succeeded in increasing the discharge uniformity to 70% of the laser-tube cross-sectional area and realized a high laser output power and a high laser efficiency. In the case of a microwave input power of 1450 W, a maximum laser output power of 273 W and a laser efficiency of 18.8% were achieved; in the case of a microwave input power of 1070 W, a laser output power of 214 W and a laser efficiency of 20.0% were achieved. At the time of maximum output power, a high input power density of 280 W/cm³, which is approximately 20 times that in a dc discharge method, was achieved. Thus, a high-output-power microwave-discharge-excited CO₂ laser has become feasible. PACS 42.60.By; 52.80.Pi     

放电激励重复频率非链式HF激光器

 利用紫外预电离横向放电和气体循环结构建立了一套放电激励重复频率HF激光装置。研究了激光器工作介质SF6/C2H6混合气体放电特性和激光输出特性,获得激光器单次运行的最佳输出参数;通过对激光器重复频率运行时不同气体流速、充电电压与气体总压条件下的放电状态和输出能量的比较,分析了激光器重复频率稳定运行的必要条件。结果表明：所研制的激光器最大单脉冲能量0.6 J,峰值功率3 MW,电光转换效率2.4%;当混合气体工作介质以3.5 m/s的流速循环时,激光器稳定运行的最高工作频率可达50 Hz,脉冲输出能量稳定在0.26 J,平均功率达到13 W。     

钙原子与离子共振-亚稳跃迁激光的同时振荡

在电极间距为46cm、内径为1.3cm的石英放电管中,通过高频纵向脉冲放电激励,获得波长为0.85μm/0.87μm和5.54μm的钙离子和原子共振-亚稳跃迁激光的同时振荡.最大激光总功率和效率分别达1.1W和0.1%.测量并分析了激光输出特性和各工作参量之间的关系.     

阵列口径Nd：YAG片状激光器重复频率输出特性研究

 介绍了一种新型阵列口径的固体片状激光器的设计及初步实验，研究了其激光输出特性。激光器采用2×1阵列的以布儒斯特角放置的片状Nd:YAG激光头模块，并采用氙灯泵浦方式，由平均功率为60 kW电池组电源供电；电源采用大电流恒流放电，对输出放电进行可编程控制。实验得到32 J的单脉冲输出，小信号增益系数为0.047 5 cm^-1；泵浦单脉冲运行，脉宽为1~5 ms时，输出能量呈线性增长；当重复频率为20 Hz时，5 ms脉宽比1 ms脉宽输出功率下降30%，其原因是布儒斯特角结构存在时，由热应力引起的热致双折射损耗造成输出下降。     

Design and operation characteristics of a high power transverse flow pulser sustained cw CO2 laser

A transverse flow, transverse discharge cw CO₂ laser in which de discharge is sustained by employing high repetition rate high voltage pulses has been developed. Pulser sustained discharge through electrodes of innovative design provided uniform excitation at electrical input power densities more than 10 W/cc. Laser output power more than 2.5 kW was obtained in a laser gas mixture consisting of 0.5 mbar of CO₂, 16 mbar of N₂ and 38.5 mbar of He. Design details and operational characteristics of this laser are presented.     

宽输出电压的半导体激光器驱动电源研究

介绍了一种大功率、宽输出电压范围的半导体激光器脉冲驱动电源的设计方法。根据半导体激光器脉冲驱动电源高电压、大电流的工作特性需求,脉冲放电环节采用多模块级联与功率开关管线性控制脉冲放电相结合的拓扑结构,这样既实现了脉冲电流平滑稳定,又提高了输出电压等级与功率。充电环节采取LCC谐振变换器结构,其抗负载短路和开路的能力非常适用于脉冲放电场合。该脉冲电源输出参数为:电压0~1000 V,电流1~160 A,脉宽200~250 μs,频率100 Hz内可调,具备较宽泛灵活的输出范围,可适应不同规模的激光二极管阵列。最后,分别通过单模块、两模块与三模块小功率级联型驱动实验验证了采用多模块级联与功率开关管线性控制脉冲放电相结合方法的可行性。     

Performance improvement of an x-ray preionized XeCl laser of very small discharge volume

Increasing the preionization electron density is found to be an effective method for improving the output performance of discharge-pumped excimer lasers at high gas pressures when the power-supply voltage becomes a limiting factor. In a small volume (2 cm³), x-ray preionized discharge, orders of magnitude improvement in XeCl laser power output (up to 400 kW) and pulse energy (up to 26 mJ) over previously reported results have been found possible using this method. Modifications to the low energy x-ray source and discharge system leading to these improvements are described. Various laser output characteristics are also presented and discussed.