Highly efficient iron–nitrogen electrocatalyst derived from covalent organic polymer for oxygen reduction

Developing non-precious metal catalyst with high activity, good stability and low cost for electrocatalytic oxygen reduction reaction(ORR) is critical for the wide application of energy conversion system. Here, we developed a cost–effective synthetic strategy via silica assistance to obtain a novel Fe_3C/Fe–N_x–C(named as COPBP-PB-Fe-900-SiO_2) catalyst with effective active sites of Fe–N_xand Fe_3C from the rational design two-dimensional covalent organic polymer(COPBP-PB). The nitrogen-rich COP effectively promotes the formation of active Fe–N_x sites. Additionally, the silica not only can effectively suppress the formation of large Fe-based particles in the catalysts, but also increases the degree of carbonization of the catalyst.The as-prepared COPBP-PB-Fe-900-SiO_2 catalyst exhibits high electrocatalytic activity for ORR with a halfwave potential of 0.85 V vs. reversible hydrogen electrode(RHE), showing comparable activity as compared with the commercial Pt/C catalysts in alkaline media. Moreover, this catalyst also shows a high stability with a nearly constant onset potential and half-wave potential after 10,000 cycles. The present work is highly meaningful for developing ORR electrocatalysts toward wide applications.     

Hierarchically porous N-doped carbon derived from biomass as oxygen reduction electrocatalyst for high-performance Al–air battery

Developing large-scale and highly efficient oxygen reduction reaction(ORR)catalysts acts a vital role in realizing wide application of metal–air batteries.Here,we propose a gas-foaming strategy to fabricate sustainable and 3D hierarchically porous N-doped carbon with high specific surface area and abundant defects sites derived from biomass.The obtained catalyst exhibits prominent ORR property with higher half-wave potential(0.861 V)and slightly lower kinetic current density(32.44 m A cm^-2),compared to Pt/C(0.856 V and 43.61 m A cm^-1).Furthermore,employing it as catalyst of air cathode,the Al–air battery delivers remarkable discharge performance with excellent power density of 401 m W cm^-2,distinguished energy density of 2453.4 Wh kg^-1 and extremely high open-circuit voltage of 1.85 V among the reported metal–air batteries in the literatures.This gas-foaming strategy for full utilization of biomass affords a chance to explore scalable advanced catalysts in metal–air battery.     

N-doped graphitic carbon encapsulating cobalt nanoparticles derived from novel metal–organic frameworks for electrocatalytic oxygen evolution reaction

Nitrogen-doped carbon catalysts with hierarchical porous structure are promising oxygen evolution reaction (OER) catalysts due to the faster mass transfer and better charge carrying ability. Herein, an exquisite high nitrogen-containing ligand was designed and readily synthesized from the low-cost biomolecule adenine. Accordingly, three new MOFs (TJU-103, TJU-104 and TJU-105) were prepared using the Co(II) or Mn(II) ions as metal nodes. Through rationally controlling pyrolysis condition, in virtue of the high nitrogen content in well-defined periodic structure of the pristine MOFs, TJU-104–900 among the derived MOFs with hierarchical porous structure, i.e., N-doped graphitic carbon encapsulating homogeneously distributed cobalt nanoparticles, could be conveniently obtained. Thanks to the synergistic effect of the hierarchical structure and well dispersed active components (i.e., C=O, Co‒N_x, graphitic C and N, pyridinic N), it could exhibit an overpotential of 280 mV@10 mA/cm² on carbon cloth for OER activity. This work provides the inspiration for fabrication of nitrogen-doped carbon/metal electrocatalysts from cost-effective and abundant biomolecules, which is promising for practical OER application.     

Ir–V nanoparticles supported on microstructure controlled carbon nanofibers as electrocatalyst for oxygen reduction reaction

Ir–V nanoparticles supported on microstructure controlled carbon nanofibers (CNFs) or on carbon black, Vulcan XC-72 (XC-72), have been synthesized via chemical reduction, and the oxygen reduction reaction (ORR) properties of catalysts are investigated in this paper. The physico-chemical properties are characterized by high resolution transmission electron microscope (HRTEM), N₂ physisorption and electrochemical analysis. HRTEM results show that the metal nanoparticles are separated on carbon support with well-controlled particle size, dispersity, and composition uniformity. Moreover, the metal nanoparticles on CNFs have a smaller size than those on XC-72. Cyclic voltammetric analysis reveals that Ir–V/CNFs exhibits a higher ORR activity than Ir–V/XC-72, and this may be associated with the smaller metal nanoparticles and the stronger metal-support interaction of Ir–V/CNFs. Linear sweep voltammetric analysis at different rotation rates proves that ORR on the Ir–V/CNFs electrode is a 4e^? process.     

Nitrogen-doped hierarchical porous carbon derived from metal–organic aerogel for high performance lithium–sulfur batteries

Nitrogen-doped three-dimensional(3 D) porous carbon materials have numerous applications due to their highly porous structures, abundant structural nitrogen heteroatom decoration and low densities. Herein,nitrogen doped hierarchical 3 D porous carbons(NHPC) were prepared via a novel metal–organic aerogel(MOA), using hexamethylenetetramine(HMT), 1,3,5-benzenetricarboxylic acid and copper(II) as starting materials. The morphology, porous structure of the building blocks in the NHPC can be tuned readily using different amount of HMT, which makes elongation of the pristine octahedron of HKUST-1 to give rise to different aspect ratio rod-like structures. The as-prepared NHPC with rod-like carbons exhibit high performance in lithium sulfur battery due to the rational ion transfer pathways, high N-doped doping and hierarchical porous structures. As a result, the initial specific capacity of 1341 m A h/g at rate of 0.5 C(1 C = 1675 m A h/g) and high-rate capability of 354 m A h/g at 5 C was achieved. The decay over 500 cycles is 0.08% per cycle at 1 C, highlighting the long-cycle Li–S batteries.     

Metal-organic-framework-derived formation of Co–N-doped carbon materials for efficient oxygen reduction reaction

Non-precious metal nitrogen-doped carbonaceous materials have attracted tremendous attention in the field of electrochemical energy storage and conversion. Herein, we report the designed synthesis of a novel series of Co-N-C nanocomposites and their evaluation of electrochemical properties. Novel yolkshell structured Co nanoparticles@polymer materials are fabricated from the facile coating polymer strategy on the surface of ZIF-67. After calcination in nitrogen atmosphere, the Co–N–C nanocomposites in which cobalt metal nanoparticles are embedded in the highly porous and graphitic carbon matrix are successfully achieved. The cobalt nanoparticles containing cobalt metal crystallites with an oxidized shell and/or smaller(or amorphous) cobalt-oxide deposits appear on the surface of graphitic carbons. The prepared Co–N–C nanoparticles showed favorable electrocatalytic activity for oxygen reduction reactions,which is attributed to its high graphitic degree, large surface area and the large amount existence of Co–N active sites.     

Environment friendly hydrothermal synthesis of carbon–Co_3O_4 nanorods composite as an efficient catalyst for oxygen evolution reaction

The design of cost-effective, highly active catalysts for hydrogen energy production is a vital element in the societal pursuit of sustainable energy. Water electrolysis is one of the most convenient processes to produce high purity hydrogen. Cobalt-based catalysts are well-known electrocatalysts for oxygen evolution reaction(OER). In this article, all these merits indicate that the present cobalt nanocomposite is a promising electrocatalyst for OER. C–Co_3O_4-nanorods catalyst with nanorod structure was synthesized by hydrothermal treatment of CoCl_2·6H_2O/dextrose/urea mixture at 180 °C for 18 h and then calcined at400 °C for 3.5 h. The role of dextrose percentage in solution to achieve the uniform coating of carbon on the surface of Co_3O_4-nanorods has been demonstrated. The prepared materials were characterized by X-ray diffraction(XRD), X-ray photoelectron spectrum(XPS), field emission scanning electron microscopy(FE-SEM), high-resolution transmission electron microscopy(HR-TEM), and Brunauer–Emmett–Teller instrument(BET). Due to its unique morphology, the C–Co_3O_4-nanorods catalyst exhibited better activity than Co_3O_4-microplates catalyst for OER in 1 M KOH aqueous solution. The results showed a highly efficient, scalable, and low-cost method for developing highly active and stable OER electrocatalysts in alkaline solution.     

Copper-based metal–organic framework decorated by CuO hair-like nanostructures: Electrocatalyst for oxygen evolution reaction

We report a Cu-based metal–organic framework (MOF) decorated by CuO nanostructures as an efficient catalyst for the oxygen evolution reaction (OER). MIL-53(Cu) was synthesized by a hydrothermal approach using 1,4-bezenedicarboxylic acid as organic precursor and further annealed at 300°C to form CuO nanostructures on its surface. The produced electrocatalyst, CuO@MIL-53(Cu), was characterized using various techniques. Under alkaline conditions, the developed electrocatalyst exhibited an overpotential of 801 and 336 mV versus RHE at 10 and 1 mA cm⁻², respectively. The reproducibility of the catalytic performance was validated using several electrodes. It was confirmed that the CuO hair-like nanostructures grown on MIL-53(Cu) using thermal treatment exhibit high OER activity, good kinetics and durability. CuO@MIL-53(Cu) is an economic noble-metal-free OER electrocatalyst. It has potential for application as anode material for sustainable energy technologies like batteries, fuel cells and water electrolysis.     

Nitrogen-doped mesoporous carbon nanospheres loaded with cobalt nanoparticles for oxygen reduction and Zn–air batteries

Mesoporous carbon supported with transition metals nanoparticles performs desired activities for oxygen reduction reaction (ORR) and clean energy conversion devices such as Zn–air batteries. In this work, we synthesized N-doped mesoporous carbon loaded with cobalt nanoparticles (CoMCN) through self-assembly method. There are sufficient mesopores on the carbon substrate which stem from the pore-forming agent. These mesopores can provide enough accessible active sites and profitable charge/mass transport for ORR. The high content of pyridinic and graphitic N is beneficial for promoting O₂ adsorption and reduction. The smaller value of I_D/I_G indicates the higher degree of graphitization of CoMCN, providing better electronic conductivity. The half-wave potential of CoMCN is 0.865 V in basic solution, which is 24 mV more positive than that of the commercial Pt/C (0.841 V). In addition, CoMCN performs excellent methanol tolerance and stability under both basic and acidic conditions. The Zn–air battery assembled with CoMCN performs the larger power density and open-circuit voltage than the commercial Pt/C-based battery, indicating the potential application in energy conversion systems. This work provides thoughtful ideas for fabricating transition metal nanoparticles based porous carbon for electrocatalysis and metal–air batteries.     

Improving platinum group metal–free oxygen reduction reaction electrocatalyst activity: suggestions from density functional theory studies

In this opinion, the limitations of platinum group metal–free oxygen reduction reaction electrocatalyst activity based on scaling laws and resulting Balandin-Sabatier volcano plots are presented. Previous theoretical work aimed at overcoming this limitation is discussed. A theoretical study of a novel approach toward catalyst activity improvement, dynamic strain engineering, is proposed and tested for a possible platinum group metal–free oxygen reduction reaction active site. It is shown that not only can this approach produce thermodynamic limiting potentials well beyond scaling law relationship limits but also be capable of doing so in an energy-efficient manner.     

FeAgMo2O8 — A novel oxygen evolution catalyst material for alkaline metal–air batteries

This paper reports about FeAgMo₂O₈ — a novel oxygen evolution catalyst material for secondary (rechargeable) metal–air batteries. Bifunctional air electrodes were made using FeAgMo₂O₈ as a charging catalyst for oxygen evolution reaction (OER) and silverized carbon black (Ag/C) was employed as a discharging catalyst for oxygen reduction reaction (ORR). Corresponding air electrodes were investigated using 10 M KOH as an electrolyte. At current densities between 20 and 50 mA per cm² we observed discharging and charging voltages of 1.20 to 1.15 V and 1.96 to 2.05 V, respectively.     

Metal–organic framework derived hierarchical porous TiO_2 nanopills as a super stable anode for Na-ion batteries

Hierarchical porous TiO_2 nanopills were synthesized using a titanium metal-organic framework MIL-125(Ti) as precursor. The as-synthesized TiO_2 nanopills owned a large specific surface area of 102 m~2/g and unique porous structure. Furthermore, the obtained TiO_2 nanopills were applied as anode materials for Na-ion batteries for the first time. The as-synthesized TiO_2 nanopills achieved a high discharge capacity of 196.4 m Ah/g at a current density of 0.1 A/g. A discharge capacity of 115.9 m Ah/g was obtained at a high current density of 0.5 A/g and the capacity retention was remained as high as 90% even after 3000 cycles. The excellent electrochemical performance can be attributed to its unique hierarchical porous feature.     

A two-dimensional microporous metal–organic framework for highly selective adsorption of carbon dioxide and acetylene

Solvothermal reaction of 3-aminoisonicotinic acid(Haina) and Cu(NO_3)_2·2.5H_2O gave a novel twodimensional(2D) microporous metal–organic framework, [Cu(aina)_2(DMF)]·DMF(1, DMF = N,N-dimethylformamide). Single-crystal X-ray crystallographic study of compound 1 revealed that Cu(II)ions are linked by ainaàligands forming square grid-like layers, which stack together via multiple hydrogen bonding interactions. The solvent-free framework of 1a displayed considerable porosity(void = 46.5%) with one-dimensional(1D) open channels(4.7 ? ? 4.8 ?) functionalized by amino groups.Gas sorption measurements of 1 revealed selective carbon dioxide(CO_2) and acetylene(C_2H_2) adsorption over methane(CH_4) and nitrogen(N_2) at ambient temperature.     

Hierarchical NiCo2O4 nanorods as an efficient cathode catalyst for rechargeable non-aqueous Li–O2 batteries

NiCo₂O₄ nanorods were synthesized by a hydrothermal method followed by low temperature calcination. FESEM and TEM analyses confirmed that the as-prepared materials consist of a hierarchical nanorod structure. When applied as cathode catalysts in rechargeable Li–O₂ batteries, NiCo₂O₄ nanorods exhibited a superior catalytic activity, including low charge over-potential, high discharge capacity and high-rate capability.     

Onion-like graphitic nanoshell structured Fe–N/C nanofibers derived from electrospinning for oxygen reduction reaction in acid media

Hollow onion-like graphitic nanoshell structured Fe–N/C nanofiber (Fe–N/CNF) catalyst with porous morphology was prepared by heat treating as-spun polyacrylonitrile/ferrous oxalate composite nanofibers in ammonia atmosphere for the first time. These porous electrocatalyst showed both excellent catalytic activity for oxygen reduction reaction (ORR) and much better stability than commercial Pt/C catalyst in acid solution. The Fe–N/CNF catalysts developed here could be easily fabricated on a large scale and show high potential in proton exchange membrane fuel cells (PEMFCs).     

Cu-embedded porous Al2O3 bifunctional catalyst derived from metal–organic framework for syngas-to-dimethyl ether

Dimethyl ether （DME）,as a promising alternative to diesel fuel and liquefied petroleum gas,has attracted considerable attention in catalysis domain.The catalytic direct synthesis of DME from syngas is an upand-coming route but remains a challenge.In this work,we firstly prepared a Cu-embedded porous Al₂O₃bifunctional catalyst （Cu@Al₂O₃-dp） by filling Cu-1,3,5-benzenetricarboxylate metal–organic framework（Cu-BTC MOF） with Al（OH）₃followed by a...     

Pt–NiO–Al2O3/G derived from graphene-supported layered double hydroxide as efficient catalyst for p-nitrophenol reduction

Research on Chemical Intermediates - The present work reports the synthesis of a Pt-modified NiO–Al2O3 nanocomposite derived from graphene-supported layered double hydroxide (Pt–NiO/G)...     

Bimetallic Cu–Pt/nanoporous carbon composite as an efficient catalyst for methanol oxidation

A novel bimetallic Cu–Pt nanoparticle supported onto Cu/indirectly carbonized nanoporous carbon composite (Cu–Pt/ICNPCC) was prepared through a two-step process: first, carbonization of furfuryl alcohol-infiltrated MOF-199 [metal–organic framework Cu₃(BTC)₂ (BTC?=?1,3,5-benzene tricarboxylate)], without removing the Cu metal with HF aqueous solution; second, the partial galvanic replacement reaction (GRR) of Cu nanoparticles by Pt^IV upon immersion in a platinum(IV) chloride solution. The synthesized materials characterized by powder X-ray diffraction, Fourier transform infrared spectroscopy, field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy (EDS), and electrochemical methods. The EDS result revealed that part of Cu nanoparticles have been substituted by Pt nanoparticles after GRR. The methanol oxidation at the surface of Cu–Pt/ICNPCC was investigated by cyclic voltammetry method in 0.5 M H₂SO₄ and indicated good electro-catalytic activity towards methanol oxidation (E_p?=?0.85 V vs. NHE and j_f?=?1.00 mA cm^?2). It is suggested that this improvement is attributed to the effect of proper Cu/ICNPCC for fine dispersion, efficient adhesion, and prevention of Pt coalescing.     

Preparation of yolk-shell sulfur/carbon nanocomposite via an organic solvent route for lithium–sulfur batteries

A yolk-shell sulfur/carbon (S/C) composite for the cathode of lithium–sulfur batteries was successfully prepared by an accessible method with tetrahydrofuran as solvent. The as-prepared composites are characterized by thermal gravimetric, X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption and desorption. In this composite, sulfur particle is encapsulated in the carbon shell even entering into the micropores of carbon Bp2000. The electrochemical performance of the S/C composites is evaluated. The results indicate that the S/C composite with 50 wt% sulfur content shows good reversibility, excellent rate capability, and slow degradation. It delivers an initial capacity of 784.4 mAh g^?1 (based on sulfur weight) and preserves at 598.3 mAh g^?1 after 195 cycles at 1C. It achieves a high-capacity retention of 76.27 % from the 5th to 200th cycle, and as high as 91.19 % during the latter 150 cycles. The improvement is mainly attributed to the favorable structure of the S/C composite, in which the carbon cannot only facilitate transport of electrons and Li⁺ ions but also trap polysulfides and retard the shuttle effect during charge/discharge process.