Effect of acid-base properties on copper catalysts for hydrogenation of carbon dioxide

Acidic or basic components as co-catalysts were added to the Cu-based catalysts for hydrogenation of CO₂. Effects of acid-base properties on the catalytic activity and methanol selectivity are discussed.     

负载型CuO/TiO2催化剂催化CO2加氢制甲醇

采用浸渍法制备了CuO/TiO_2负载型催化剂,并将其用于CO2加氢制甲醇反应。重点考察了铜的负载量对催化剂性能的影响,并对其物化性能和催化性能之间的关系进行了讨论。结果发现,随着铜负载量的增加,催化剂中金属铜的比表面先增加后减小,当铜的负载量为10%(质量百分数)时达到最大值。催化剂的表面碱性位数量随铜含量的增加持续减小,中等碱位和强碱位的强度下降。当铜的负载量不高于10%时,CO2的转化率与铜的比表面积呈线性关系。甲醇选择性与催化剂的表面碱位性质有关,过强的碱性位会降低甲醇选择性。     

负载型CuO/TiO2催化剂催化CO2加氢制甲醇

采用浸渍法制备了CuO/TiO₂负载型催化剂,并将其用于CO₂加氢制甲醇反应。重点考察了铜的负载量对催化剂性能的影响,并对其物化性能和催化性能之间的关系进行了讨论。结果发现,随着铜负载量的增加,催化剂中金属铜的比表面先增加后减小,当铜的负载量为10%（质量百分数）时达到最大值。催化剂的表面碱性位数量随铜含量的增加持续减小,中等碱位和强碱位的强度下降。当铜的负载量不高于10%时,CO₂的转化率与铜的比表面积呈线性关系。甲醇选择性与催化剂的表面碱位性质有关,过强的碱性位会降低甲醇选择性。     

Ti-Si composite oxide-supported cobalt catalysts for CO2 hydrogenation

In the present work, different silica-based supported cobalt (Co) catalysts were synthesized and used for CO2 hydrogenation for methanation. Different supports, such as SSP, MCM-41, TiSSP and TiMCM were used to prepare Co catalysts with 20 wt% Co loading. The supports and catalysts were characterized by means of N2 physisorption, XRD, SEM/EDX, XPS, TPR and CO chemisorption. It is found that after calcination of catalysts, Ti is present in the form of anatase. The introduction of Ti plays important roles in the properties of Co catalysts by:(i) facilitating the reduction of Co oxides species which are strongly interacted with support, (ii) preventing the formation of silicate compounds, and (iii) inhibiting the RWGS reaction. Based on CO2 hydrogenation, the CoTiMCM catalyst exhibites the highest activity and stability.     

表面助剂改性对Cu/ZnO/Al2O3甲醇合成催化剂性能的影响

采用共沉淀-后浸渍方法制备了表面助剂改性的Cu/ZnO/Al₂O₃ (CZA)甲醇合成催化剂, 在固定床反应器上以合成气为原料分别考察了三种助剂(Zr、Ba和Mn)对CZA催化剂性能的影响; 以Zr为助剂时反应温度的影响; 并进行了催化稳定性试验. 利用粉末X射线衍射(XRD)、低温氮气吸脱附(N₂-sorption)、氧化亚氮(N₂O)反应吸附技术、X射线光电子能谱(XPS)、氢气程序升温吸脱附(H₂-TPD)、扫描电子显微镜(SEM)和高分辨透射电子显微镜(HR-TEM)技术对催化剂进行了表征.结果显示: 以Zr或Ba作为助剂能够明显提高CZA催化剂耐热前后的甲醇时空收率(STY); Mn的引入降低了CZA催化剂的耐热前活性; Zr的引入降低了CZA催化剂最高活性温度点, 增强了CZA催化剂的催化稳定性; 还原态CZA催化剂表面Cu⁰和ZnO都能吸附活化氢气, Cu⁰与ZnO的强相互作用有利于提高催化剂的性能, 耐热后催化剂性能的降低归因于Cu晶粒的长大. 在实验和表征结果基础上,提出了CZA催化剂上合成气制甲醇的“双向同步催化反应历程”.     

以类水滑石为前驱体的Cu/Zn/Al/(Zr)/(Y)催化剂制备及其催化CO_2加氢合成甲醇的性能

采用共沉淀法合成了Cu:Zn:Al:Zr:Y原子比分别为2:1:1:0:0、2:1:0.8:0.2:0、2:1:0.8:0:0.2和2:1:0.8:0.1:0.1的Cu/Zn/Al/(Zr)/(Y)类水滑石化合物.将前驱体材料在空气中500°C焙烧后得到复合金属氧化物,并将其用于CO2加氢合成甲醇反应.采用X射线衍射(XRD)、热重(TG)分析、N2吸附、氧化亚氮(N2O)反应吸附、氢气程序升温还原(H2-TPR)和H2/CO2程序升温脱附(H2/CO2-TPD)技术对所制备的样品进行表征.结果表明,Zr和Y的引入使得催化剂BET比表面积大幅增加,金属铜的比表面积和分散度均按以下顺序依次增加:Cu/Zn/AlCu/Zn/Al/ZrCu/Zn/Al/YCu/Zn/Al/Zr/Y,然而,强碱位数目占总碱位数目的比例的变化顺序为:Cu/Zn/AlCu/Zn/Al/YCu/Zn/Al/Zr/YCu/Zn/Al/Zr.活性评价结果揭示CO2转化率取决于金属铜的比表面积,甲醇选择性则随强碱位比例的增加而线性增加.因而,Zr和Y的引入有利于甲醇的合成,Cu/Zn/Al/Zr/Y催化剂上的甲醇收率最高.     

二氧化碳加氢制甲醇催化剂研究进展

随着全球能源消耗的不断增长和环境污染问题的日益严重,寻找清洁、高效的CO₂利用路径成为研究热点。甲醇由于用途广泛,既是重要的化工原料,也是一种新型清洁能源。CO₂催化加氢制甲醇过程不仅实现CO₂减排,还是碳资源循环利用的有效途径之一,对解决能源紧缺和环境问题具有重要意义。高活性、高选择性和高稳定性的CO₂加氢制甲醇催化剂的开发一直是该过程的核心技术。本文综述了二氧化碳加氢制甲醇的研究进展,主要介绍了反应机理和催化剂,并以Cu基催化剂重点总结了活性位、载体和助剂对催化性能的影响,最后对二氧化碳加氢制甲醇的应用前景进行了展望。     

Carbon dioxide reforming of methane over Ni/Mo/SBA-15-La2O3 catalyst: Its characterization and catalytic performance

The Ni/Mo/SBA-15 catalyst was modified by La2O3 in order to improve its thermal stability and carbon deposition resistance during the CO2 reforming of methane to syngas. The catalytic performance, thermal stability, structure, dispersion of nickel and carbon deposition of the modified and unmodified catalysts were comparatively investigated by many characterization techniques such as N2 adsorption, H2-TPR, CO2-TPD, XRD, FT-IR and SEM. It was found that the major role of La2O3 additive was to improve the pore structure and inhibit carbon deposition on the catalyst surface. The La2O3 modified Ni/Mo/SBA-15 catalyst possessed a mesoporous structure and high surface area. The high surface area of the La2O3 modified catalysts resulted in strong interaction between Ni and Mo-La, which improved the dispersion of Ni, and retarded the sintering of Ni during the CO2 reforming process. The reaction evaluation results also showed that the La2O3 modified Ni/Mo/SBA-15 catalysts exhibited high stability.     

Effect of CO2/CO Addition in Dehydroaromatization of Methane on Zeolite-Supported Mo and Re Catalysts Towards Hydrogen, Benzene and Naphthalene

High activity and high formation selectivity for aromatics in the dehydrocondensation reaction of methane were realized only on selected catalysts. The requisites of a metal and a zeolite support as the selected catalyst were described. However, the catalytic activity steadily declined even on the selected catalysts with time on stream because of coke accumulation. A stable catalytic activity was obtained when CO₂ or CO was added into methane feed due to effective removal of coke from the catalyst surface by CO or CO₂. The route from methane to aromatics and the formation process of active phase of catalyst were discussed.     

铬助剂对Cu/ZrO_2/CNTs-NH_2催化剂催化CO_2加氢合成甲醇性能的影响

采用并流共沉淀方法制备了一系列不同铬含量的Cu/ZrO2/CNTs-NH2催化剂,在固定床反应器上考察铬对催化剂催化CO2加氢合成甲醇反应性能的影响.当铬含量为1%(w),反应温度为260°C,压力为3.0MPa,原料气组成为V(H2):V(CO2):V(N2)=69:23:8,空速为3600 mL·h-1·g-1时,催化剂的促进效果最显著,甲醇收率达7.78%.氮吸附、粉末X射线衍射(XRD)、氢气程序升温脱附(H2-TPR)、X射线光电子能谱(XPS)、二氧化碳程序升温脱附(CO2-TPD)、差热分析(DTA)以及扫描电子显微镜(SEM)等表征结果表明,随着铬含量的增加,铜颗粒的粒径减小,催化剂的比表面积增大.铬的加入一方面提高了铜的分散性,抑制了ZrO2的相变和活性组分的烧结;另一方面提高了CO2的吸附量并促进CO2由弱吸附向强吸附转化,从而提高甲醇的收率;但是当铬含量大于1%时,催化剂表面Cu、Zr的总含量明显下降,降低了CO2的吸附量并且形成了超强CO2吸附物种,抑制了CO2及其中间产物的转化,从而降低了甲醇收率.     

CO2 hydrogenation to methanol and dimethyl ether at atmospheric pressure using Cu-Ho-Ga/γ–Al2O3 and Cu-Ho-Ga/ZSM-5: Experimental study and thermodynamic analysis

CO₂ valorization through chemical reactions attracts significant attention due to the mitigation of greenhouse gas effects. This article covers the catalytic hydrogenation of CO₂ to methanol and dimethyl ether using Cu-Ho-Ga containing ZSM-5 and g-Al₂O₃ at atmospheric pressure and at temperatures of 210 °C and 260 °C using a CO₂:H₂ feed ratio of 1:3 and 1:9. In addition, the thermodynamic limitations of methanol and DME formation from CO₂ was investigated at a temperature range of 100–400 °C. Cu-Ho-Ga/g-Al₂O₃ catalyst shows the highest formation rate of methanol (90.3 µmol_CH3OH/g_cat/h ) and DME (13.2 µmol_DME/g_cat/h) as well as the highest selectivity towards methanol and DME (39.9 %) at 210 °C using a CO₂:H₂ 1:9 feed ratio. In both the thermodynamic analysis and reaction results, the higher concentration of H₂ in the feed and lower reaction temperature resulted in higher DME selectivity and lower CO production rates.     

A study on methanol steam reforming to CO2 and H2 over the La2CuO4 nanofiber catalyst

The La₂CuO₄ crystal nanofibers were prepared by using single-walled carbon nanotubes as templates under mild hydrothermal conditions. The steam reforming of methanol (SRM) to CO₂ and H₂ over such nanofiber catalysts was studied. At the low temperature of 150 °C and steam/methanol=1.3, methanol was completely (100%, 13.8 g/h g catalyst) converted to hydrogen and CO₂ without the generation of CO. Within the 60 h catalyst lifespan test, methanol conversion was maintained at 98.6% (13.6 g/h g catalyst) and with 100% CO₂ selectivity. In the meantime, for distinguishing the advantage of nanoscale catalyst, the La₂CuO₄ bulk powder was prepared and tested for the SRM reaction for comparison. Compared with the La₂CuO₄ nanofiber, the bulk powder La₂CuO₄ showed worse catalytic activity for the SRM reaction. The 100% conversion of methanol was achieved at the temperature of 400 °C, with the products being H₂ and CO₂ together with CO. The catalytic activity in terms of methanol conversion dropped to 88.7% (12.2 g/h g catalyst) in 60 h. The reduction temperature for nanofiber La₂CuO₄ was much lower than that for the La₂CuO₄ bulk powder. The nanofibers were of higher specific surface area (105.0 m²/g), metal copper area and copper dispersion. The in situ FTIR and EPR experiments were employed to study the catalysts and catalytic process. In the nanofiber catalyst, there were oxygen vacancies. H₂-reduction resulted in the generation of trapped electrons [e] on the vacancy sites. Over the nanofiber catalyst, the intermediate H₂CO/HCO was stable and was reformed to CO₂ and H₂ by steam rather than being decomposed directly to CO and H₂. Over the bulk counterpart, apart from the direct decomposition of H₂CO/HCO to CO and H₂, the intermediate H₂COO might go through two decomposition ways: H₂COO=CO+H₂O and H₂COO=CO₂+H₂.     

Effect of sodium cation on the electrochemical reduction of CO<Subscript>2</Subscript> at a copper electrode in methanol

The electrochemical reduction of CO₂ with a Cu electrode in methanol was investigated with sodium hydroxide supporting salt. A divided H-type cell was employed; the supporting electrolytes were 80 mmol dm⁻³ sodium hydroxide in methanol (catholyte) and 300 mmol dm⁻³ potassium hydroxide in methanol (anolyte). The main products from CO₂ were methane, ethylene, carbon monoxide, and formic acid. The maximum current efficiency for hydrocarbons (methane and ethylene) was 80.6%, at −4.0 V vs Ag/AgCl, saturated KCl. The ratio of current efficiency for methane/ethylene, r _f(CH₄)/r _f(C₂H₄), was similar to those obtained in LiOH/methanol-based electrolyte and larger relative to those in methanol using KOH, RbOH, and CsOH supporting salts. In NaOH/methanol-based electrolyte, the efficiency of hydrogen formation, a competing reaction of CO₂ reduction, was suppressed to below 4%. The electrochemical CO₂ reduction to methane may be able to proceed efficiently in a hydrophilic environment near the electrode surface provided by sodium cation.     

CO2 reforming of methane over zirconia-supported nickel catalysts, I. Catalytic specificity

CO₂ reforming of methane is performed over zirconia-supported nickel catalysts. The catalysts show high activity toward CH₄ and CO₂ conversions. Over the high Ni loading catalyst, long-term performances without significant deactivations have been achieved at 1023 K for 30 h and 1123 K for 20 h, respectively. The effects of reduction and calcination temperatures on the catalytic activities are also examined.     

DME Synthesis From CO/H2 over Cu-Mn/?-Al2O3 Catalyst

A γ-alumina-supported copper-manganese oxide catalyst prepared by an impregnation method was used for DME synthesis from CO/H₂ (syngas). The Cu-Mn/γ-Al₂O₃ catalyst exhibits high catalytic activity in CO hydrogenation. The effect of the loading amount of Cu, the ratio of n(Cu)/n(Mn) and the reaction conditions on the activity and selectivity to dimethyl ether (DME) from CO/H₂ (syngas) were investigated. The activity was found to increase with increasing surface area of metallic copper to some extent, but it is not a linear relationship. This indicated that the catalytic activity depends on both the metallic copper area and the synergy between the copper and manganese oxide. This revised version was published online in June 2006 with corrections to the Cover Date.     

CO/CO2一步法制备航空煤油的研究进展

CO/CO₂一步法制备航空煤油技术是石油基航空煤油重要的替代手段之一。目前,CO一步法制备航空煤油技术存在的主要问题是航空煤油组分C₈~C₁₆选择性不高。CO₂一步法制备航空煤油存在的问题是CO₂转化率低和C₈~C₁₆选择性不高。综述了近五年CO/CO₂一步法制备航空煤油用催化剂的研究进展。催化剂研究的重点在于主催化剂、载体和助催化剂。调变主催化剂、载体和助催化剂,有望得到理想的航空煤油组分。     

Small Cobalt Nanoparticles Favor Reverse Water-Gas Shift Reaction Over Methanation Under CO2 Hydrogenation Conditions**

Cobalt-based catalysts are well-known to convert syngas into a variety of Fischer–Tropsch (FTS) products depending on the various reaction parameters, in particular particle size. In contrast, the reactivity of these particles has been much less investigated in the context of CO₂ hydrogenation. In that context, Surface organometallic chemistry (SOMC) was employed to synthesize highly dispersed cobalt nanoparticles (Co-NPs) with particle sizes ranging from 1.6 to 3.0 nm. These SOMC-derived Co-NPs display significantly different catalytic performances under CO₂ hydrogenation conditions: while the smallest cobalt nanoparticles (1.6 nm) catalyze mainly the reverse water-gas shift (rWGS) reaction, the larger nanoparticles (2.1–3.0 nm) favor the expected methanation activity. Operando X-ray absorption spectroscopy shows that the smaller cobalt particles are fully oxidized under CO₂ hydrogenation conditions, while the larger ones remain mostly metallic, paralleling the observed difference of catalytic performances. This fundamental shift of selectivity, away from methanation to reverse water-gas shift for the smaller nanoparticles is noteworthy and correlates with the formation of CoO under CO₂ hydrogenation conditions.     

柠檬酸辅助固相研磨法制备铜基催化剂及在CO_2加氢合成甲醇反应中的性能研究

通过柠檬酸辅助固相研磨法制备铜基催化剂,采用XRD、TPR、TG-DSC、SEM、BET、TEM、XPS、CO_2-TPD等手段对催化剂性能进行表征.结果表明室温固相研磨的前驱体在惰性气体N_2中焙烧使体系中的CuO绝大部分被原位还原成Cu~0,不需外加H_2还原,直接制得了C/I-Cu/ZnO催化剂,催化剂具有中孔.利用高压固定床连续反应装置对催化剂活性进行了评价,结果表明,柠檬酸用量、前驱体焙烧温度、焙烧升温速率等条件对催化剂活性产生影响,当C_6H_8O_7/(Cu+Zn)摩尔比为1.2/1并Cu/Zn摩尔比1/1,前驱体在N_2中以3 K·min~(-1)升温速率于623 K焙烧3 h,制得的C/I-Cu/ZnO催化剂比表面积最大,Cu~0粒径最小,在CO_2加氢合成甲醇反应中表现出最佳的活性,CO_2转化率、甲醇选择性和产率分别达到了28.28%、74.29%和21.01%.与外加H_2还原的C/H-Cu/ZnO催化剂相比,原位还原C/I-Cu/ZnO催化剂比表面积较大,Cu~0的粒径较小,活性较高.     

Titania supported copper catalysts for methanol synthesis from carbon dioxide

The effect of co-catalyst (ZnO or ZrO₂) has been tested for hydrogenation of CO₂ on CuO/TiO₂ and CuO/Al₂O₃. CuO−ZnO/TiO₂ catalyst showed the highest activity for methanol synthesis. Kinetic parameters were also determined.     

Hydrothermal CO2 Reduction by Glucose as Reducing Agent and Metals and Metal Oxides as Catalysts

High-temperature water reactions to reduce carbon dioxide were carried out by using an organic reductant and a series of metals and metal oxides as catalysts, as well as activated carbon (C). As CO₂ source, sodium bicarbonate and ammonium carbamate were used. Glucose was the reductant. Cu, Ni, Pd/C 5%, Ru/C 5%, C, Fe₂O₃ and Fe₃O₄ were the catalysts tested. The products of CO₂ reduction were formic acid and other subproducts from sugar hydrolysis such as acetic acid and lactic acid. Reactions with sodium bicarbonate reached higher yields of formic acid in comparison to ammonium carbamate reactions. Higher yields of formic acid (53% and 52%) were obtained by using C and Fe₃O₄ as catalysts and sodium bicarbonate as carbon source. Reactions with ammonium carbamate achieved a yield of formic acid up to 25% by using Fe₃O₄ as catalyst. The origin of the carbon that forms formic acid was investigated by using NaH¹³CO₃ as carbon source. Depending on the catalyst, the fraction of formic acid coming from the reduction of the isotope of sodium bicarbonate varied from 32 to 81%. This fraction decreased in the following order: Pd/C 5% > Ru/C 5% > Ni > Cu > C ≈ Fe₂O₃ > Fe₃O₄.