Preparation and characterization of NiFe2O4/NiO composite film via a single-source precursor route

NiFe₂O₄/NiO nanocomposite thin films have been successfully prepared through a facile route using nickel iron layered double hydroxide (NiFe-LDH) as a single-source precursor. This synthetic approach mainly involves the formation of NiFe-LDH film by casting the slurry of NiFe-LDH precursor on the α-Al₂O₃ substrate, followed by high-temperature calcination. The composition, microstructure and properties of the films were characterized in detail by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDX) and vibrating sample magnetometer (VSM). The results indicate that NiFe₂O₄/NiO composite film was composed of granules with diameter less than 100 nm, and the thickness of the film was in the range 1-2 μm. The magnetization of the film can be tuned by alternating the Ni/Fe molar ratio of LDH precursor. In addition, the method developed should be easily extended to fabricate other MFe₂O₄/MO composite film systems with specific applications just by an appropriate combination of divalent/trivalent composition in the precursor of LDHs.     

Preparation, characterization and electrochemical property of Sn-Fe-Mo-Al2O3 multi-phase composites

A novel technique has been developed to synthesize Sn-Fe-Mo-Al₂O₃, while nanoscale dispersion of a highly active tin phase was finely distributed in a stable inert multi-phase. The precursor was prepared by co-precipitation method with SnCl₄, FeCl₃, AlCl₃ and (NH₄)₆Mo₇O₂₄ as the raw materials. Sn-Fe-Mo-Al₂O₃ mixture was produced by reducing the precursor with H₂. The product was characterized by X-ray diffraction (XRD), ICP and scanning electron microscopy (SEM). The performance of the electrode was investigated. The Sn-Fe-Mo-Al₂O₃ electrode was found to have an initial charge capacity of over 461 mAh/g, and a reversible volumetric capacity of 2090 mAh/cm³, which is two times larger than that of graphite electrode (800 mAh/cm³). The coulomb efficiency in the first cycle was over 55%, but its cyclability was not improved significantly. In order to enhance the cycle performance, we investigated the anode after heat treated at 270 °C for 12 h. Under the same condition, the first charge-discharge characteristics were almost equivalent to the as-coated anode, and the retention capacity ratio after 20 cycles was improved from 41.1% to 86.5%. The heat-treated Sn-Fe-Mo-Al₂O₃ electrode exhibited better cycle life. The electrochemical reaction of the Sn-Fe-Mo-Al₂O₃ electrode with Li may obey the alloying-dealloying mechanism of Li_xSn(x?4.4) formation in the other tin-based electrodes.     

Ni-Al layered double hydroxides modified with citrate, malate, and tartrate: Preparation by coprecipitation and uptake of Cu from aqueous solution

We report on aqueous Cu²⁺ uptake by Ni-Al layered double hydroxides (Ni-Al LDHs) modified with citrate (C₆H₅O₇³⁻), malate (C₄H₄O₅²⁻), and tartrate (C₄H₄O₆²⁻) anions via coprecipitation. Dropwise addition of a mixed aqueous solution of Ni(NO₃)₂ and Al(NO₃)₃ to the respective organic acid solutions at a constant pH of 7.0-9.0 afforded LDHs with intercalated C₆H₅O₇³⁻ and Ni(C₆H₅O₇⁾⁻, C₄H₄O₅²⁻, and C₄H₄O₆²⁻ in their interlayers. The anions were also likely adsorbed on the LDH surface. Citrate·Ni-Al LDH could rapidly take up Cu²⁺ at a constant pH of 5.0, mainly via chelation by the intercalated and adsorbed anions, rather than coprecipitation with dissolved Al³⁺ to form Cu-Al LDH. By contrast, malate and tartrate were not active as chelating agents, probably because they formed bridges between brucite-like layers by direct coordination of the two −COO⁻ groups with Al³⁺ in those layers.     

Synthesis and characterization of MCM-41 decorated with CuO particles

CuO particles have decorated on the external surface of MCM-41 by in situ introducing cupric nitrate during the hydrothermal synthesis followed by the calcination. The textural and structural properties of CuO/MCM-41 are compared with those of pure MCM-41. The results show that CuO particles are about 40 nm in size and are not agglomerated. The addition of cupric nitrate to the synthesis gel leads to materials with somewhat reduced quality as evidenced from X-ray diffraction patterns and nitrogen adsorption measurements. CuO/MCM-41 is less ordered relative to pure MCM-41 and there are inter-aggregate pores resulting in a higher average pore diameter in the material. The formation of CuO particles on the external surface of MCM-41 and the possible reason for the less ordered structure of CuO/MCM-41 are also discussed in the present paper.     

The first synthesis of a graphite bis(oxalato)borate intercalation compound

A new graphite intercalation compound containing the bis(oxalato)borate anion, B[OC(O)C(O)O]₂⁻, is prepared for the first time by chemical oxidation of graphite with fluorine gas in the presence of a solution containing the intercalate anion in anhydrous hydrofluoric acid. The products of stage 1-3 compounds are characterized by powder X-ray diffraction, thermogravimetric analysis, and elemental analyses. X-ray diffraction data indicate a standing-up orientation for the borate anion, with long axis perpendicular to the graphene sheets. Elemental analyses provide x and δ for the nominal composition of C_xB[OC(O)C(O)O]₂·δF, where the chelate borate and fluoride are co-intercalates, and indicate a low borate, and high fluoride, intercalate content as compared to anion packing in other graphite intercalation compounds.     

Particle size distribution and electrochemical properties of LiFePO4 prepared by a freeze-drying method

The electrochemical performance of carbon-coated nanocrystalline LiFePO₄ prepared by a freeze-drying method is examined. This method is based on the thermal decomposition of homogeneous phosphate-formate precursors. Structural and morphological characterization of LiFePO₄ is carried out by powder XRD, BET measurements, SEM and XPS analyses. The electrochemical behaviour is tested in model lithium cells using galvanostatic mode. By changing the solution concentration, the freeze-drying method allows preparing LiFePO₄ with mean particle sizes between 60 and 100 nm and different particle size distributions. The content of carbon appearing mainly on the particle surface depends on both the solution concentration and the annealing temperature. The effect of particle size distribution on the voltage profile of LiFePO₄ is also demonstrated. The specific capacity is mainly determined by the amount of carbon deposited on the particle surfaces.     

Synthesis of modified vermiculite by interaction with aromatic heterocyclic amines

Vermiculite of general formula [Si_6.85Al_1.15][Mg_4.68Al_0.51Fe_0.63]O₂₀(OH)₄Ca_0.128Na_0.032K_0.094 reacted with heteroaromatic amines α-, β-, and γ-picolines from aqueous solution. The products were characterized by elemental analysis, infrared spectroscopy, and X-ray diffraction. The intercalated nanocompounds maintained the crystallinity and changed the original interlayer distance of 1422 pm to 1474, 1456, and 1474 pm, for the sequence of the guest picoline molecules. Natural and intercalated vermiculite can remove copper at the solid/liquid interface; removal 0.40 mmol g⁻¹ was obtained for the original matrix, and 1.10, 0.92, and 1.33 mmol g⁻¹ for the intercalated forms. These values are near the capacity of cation exchange (CEC) of this clay mineral, which can be possibly used as source of copper removal from aqueous solution.     

PAA-assisted synthesis of CaCO3 microcrystals and affecting factors under microwave irradiation

In the present paper, we described a polyacrylic acid (PAA)-assisted microwave irradiation route for synthesis of Calcium carbonate (CaCO₃) microcrystals. CaCl₂·2H₂O and NaHCO₃ were used as the starting reactants. Researches showed that the presence of PAA could strongly affect the phase and morphology of CaCO₃ crystals. X-ray powder diffraction (XRD) analyses showed that the product prepared from the system with/without PAA corresponded to Vaterite/Calcite, respectively. Scanning electron microscopy (SEM) observations showed that the hierarchical CaCO₃ microcrystals were obtained in the presence of PAA. Some factors influencing the morphology of the as-synthesized CaCO₃ crystals were systematically investigated.     

Preparation of organic acid anion-modified magnesium hydroxides by coprecipitation: A novel material for the uptake of heavy metal ions from aqueous solutions

New layered magnesium hydroxides whose brucite layers had been bridged with malate²⁻ and tartrate²⁻ were prepared by dropwise addition of Mg(NO₃)₂ to malate and tartrate solutions at a constant pH of 10.5. Malate²⁻ and tartrate²⁻ may have been also absorbed on the surfaces of hydroxides. In the case of using citrate solution, Mg(OH)₂ absorbed with citrate³⁻ was produced. These materials were found to take up Cu²⁺ rapidly from an aqueous solution at pH 5.0. Copper uptake by precipitates is attributed to the formation of chelate complexes of Cu²⁺ with citrate³⁻, malate²⁻, and tartrate²⁻.     

Synthesis and structural characterization of a series of lanthanide stannate pyrochlores

A simple hydrothermal method has been employed to prepare a series of lanthanide stannate pyrochlores Ln₂Sn₂O₇ (Ln=Y, La, Pr-Yb) at a relatively low temperature of less than 200 °C successfully. On the basis of structural characterizations by X-ray powder diffraction (XRD), Fourier transform infrared (FT-IR) absorption spectroscopy and Raman spectroscopy, it was found that the positions of bands in vibrational spectra are sensitive to the ionic radius of Ln³⁺, and the linear relationship can be seen between the frequency of Sn-O stretching mode and the lanthanide ionic radius in IR spectrum, as well as the frequency of O-Sn-O bending mode and the lanthanide ionic radius in Raman spectrum.     

Advanced electrochemical performance of LiMn1.4Cr0.2Ni0.4O4 as 5 V cathode material by citric-acid-assisted method

Spinel LiMn₂O₄ and LiMn_1.4Cr_0.2Ni_0.4O₄ cathode materials were successfully synthesized by the citric-acid-assisted sol-gel method with ultrasonic irradiation stirring. The structure and electrochemical performance of the as-prepared powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectrometer, cyclic voltamogram (CV) and the galvanostatic charge-discharge test in detail. XRD shows that all the samples have high phase purity, and the powders are well crystallized. SEM exhibits that LiMn_1.4Cr_0.2Ni_0.4O₄ has more uniform cubic-structure morphology than that of LiMn₂O₄. EDX reveals that a small amount of Mn³⁺ still exists in LiMn_1.4Cr_0.2Ni_0.4O₄. The galvanostatic charge-discharge test indicates that the initial discharge capacities for the LiMn_1.4Cr_0.2Ni_0.4O₄ and LiMn₂O₄ at 0.15 C discharge rates are 130.8 and 130.2 mAh g⁻¹, respectively. After 50 cycles, their capacity are 94.1% and 85.1%, respectively. The CV curve implies that Ni and Cr dual substitutions are beneficial to the reversible intercalation and deintercalation of Li⁺, and suppress Mn³⁺ generation at high temperatures and provide improved structural stability.     

Preparation and characterization of lithium niobate as a novel photocatalyst in hydrogen generation

Several chemical compounds based lithium niobate have been tested in the reaction for the photocatalytic hydrogen generation. The photocatalysts have been prepared by impregnation of Nb₂O₅ in the aqueous solution of lithium hydroxide and then the calcination at the temperature range of 400-650 °C. In this report, we present the interesting study showing that the most active catalyst for the photocatalytic generation of hydrogen is the one containing two lithium niobate phases such as LiNbO₃ and LiNb₃O₈. It means that the lithium niobates based catalyst without any further modification or doping can be applied as a novel material for this process.     

Preparation, characterization and photocatalytic activity of metal-loaded NaNbO3

Fe-, Ni-, Co- and Ag- loaded NaNbO₃ catalysts were prepared and their activities have been investigated in the reaction of photocatalytic hydrogen generation. Me/NaNbO₃ were synthesized by impregnation of NaNbO₃ in an aqueous solution of metal nitrates and then by calcination at the temperature of 400 °C. The crystallographic phases and optical and vibronic properties were examined by X-ray diffraction (XRD) and diffuse reflectance (DR) UV-vis and resonance Raman spectroscopic methods, respectively. Morphology and chemical composition of the produced samples were studied using a high-resolution transmission electron microscope (HR-TEM) and an energy dispersive X-Ray spectrometer (EDX) as its mode. The detailed analysis has revealed that all the investigated catalysts exhibit high crystallinity and the presence of Fe₂O₃, NiO, Co₃O₄ and Ag₂O oxides on Me/NaNbO₃ was confirmed. Finally, the influence of different metal loadings (Fe, Ni, Co and Ag) on the photocatalytic activity of NaNbO₃ for photocatalytic hydrogen generation has been investigated. Here we report that among all the Me/NaNbO₃ photocatalysts Ag-loaded NaNbO₃ exhibited higher photocatalytic efficiency for photocatalytic hydrogen generation than NaNbO₃.     

Two different approaches to synthesizing Mg-Al-layered double hydroxides as folic acid carriers

Layered double hydroxides (LDHs) are a class of artificially constructed materials that have potential applications in a wide range of fields, including biomedical research and drug development. In this study, we have successfully intercalated folic acid into LDH using two different approaches: co-precipitation and ion exchange. The resultant LDH-folic acid constructs were then characterized by powdered sample X-ray diffraction (XRD), Fourier transform infrared spectra (FT-IR), transmission electron microscopy (TEM), thermogravimetry and differential thermal analysis (TG-DTA). XRD data demonstrated that folic acid molecules remained intact and stable between the hydroxide layers in LDH particles constructed by both co-precipitation and ion-exchange methods, with interlayer spacings of 15.3 and 16.0 Å, respectively. Particle size and surface topography were also determined using TEM. Cytotoxicity test revealed that neither LDH nor LDH-folic acid nanohybrids were toxic to the cell line 293T, suggesting that they can be used as a safe and noncytotoxic drug delivery system. Furthermore, the buffering effect of the intercalated LDH was evaluated. This work provides fundamental insights and technical details for utilizing biofunctional molecules that can form nanobiohybrid particles.     

Preparation of cerium hydroxycarbonate by a surfactant-assisted route

Cerium hydroxycarbonate (CeOHCO₃) with shuttle-like morphology has been conveniently synthesized at 90 °C from aqueous solution in the presence of polyvinylpyrrolidone (PVP). The products were characterized by X-ray diffraction, transmission electron microscopy and photoluminescent (PL) techniques. The as-prepared CeOHCO₃ was found to have a PL emission at about 347 nm. Experimental conditions as well as the role of PVP played in the reaction were also explored.     

Synthesis and electrochemical performances of Li4Ti4.95Al0.05O12/C as anode material for lithium-ion batteries

Spinel compounds Li₄Ti_5−xAl_xO₁₂/C (x=0, 0.05) were synthesized via solid state reaction in an Ar atmosphere, and the electrochemical properties were investigated by means of electronic conductivity, cyclic voltammetry, and charge-discharge tests at different discharge voltage ranges (0-2.5 V and 1-2.5 V). The results indicated that Al³⁺ doping of the compound did not affect the spinel structure but considerably improved the initial capacity and cycling performance, implying the spinel structure of Li₄Ti₅O₁₂ was more stable when Ti⁴⁺ was substituted by Al³⁺, and Al³⁺ doping was beneficial to the reversible intercalation and deintercalation of Li⁺. Al³⁺ doping improved the reversible capacity and cycling performance effectively especially when it was discharged to 0 V.     

Solvent-controlled syntheses of Ni12P5 and Ni2P nanocrystals and photocatalytic property comparison

Nickel phosphide nanocrystals with various phases have been successfully synthesized via a simple solvothermal route at 180 °C for 16 h, employing nickel chloride and white phosphorus (WP) as starting reactants in the presence of sodium dodecylbenzene sulfonate (SDBS). X-ray powder diffraction (XRD) research showed that the pure Ni₁₂P₅ phase with a high yield could be obtained in an ethanol solution, and the pure Ni₂P form was prepared in a mixed system with the volume ratio of water/ethanol of 10:10. Namely, the presence of water molecules induced the phase conversion of nickel phosphides. Furthermore, in order to investigate the correlation between properties and phases, as a case, the photocatalytic degradation abilities of two nickel phosphide phases for organic dyes were compared.     

Deep desulfurization of model gasoline over photoirradiated titanium-pillared montmorillonite

The activity of Ti-pillared montmorillonite for photocatalytic oxidative desulfurization using 2,5-dimethylthiophene dissolved in n-octane as a model organosulfur compound in gasoline was investigated. Using Ti-pillared montmorillonite and an oil/acetonitrile two-phase extraction, deep desulfurization of sulfur-containing compounds was achieved. During this process, O₂ was used as the oxygen source and photoirradiation was achieved by UV light. Using this approach, 97.4% of the sulfur compounds were oxidized and successfully removed from the model gasoline system under mild reaction conditions. Montmorillonite was prepared by sol–gel method and characterized by XRD, N₂ absorption and UV–vis spectroscopy. The characterization indicates that Ti component enters the interlayer of montmorillonite, working as an active component in the crystal phase of anatase. Deep desulfurization experiments show that the activity of Ti-pillared montmorillonite is obviously better than P25.     

Study on the electrochemical behavior of vanadium nitride as a promising supercapacitor material

Vanadium nitride (VN) powder was synthesized by calcining V₂O₅ xerogel in a furnace under an anhydrous NH₃ atmosphere at 400 °C. The structure and surface morphology of the obtained VN powder were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The supercapacitive behavior of VN in 1 M KOH electrolyte was studied by means of cyclic voltammetry (CV), constant current charge-discharge cycling (CD) and electrochemical impedance spectroscopy (EIS). The XRD result indicates that the obtained VN belongs to the cubic crystal system (Fm3m [2 2 5]) with unit-cell parameter 4.15 Å. SEM images show the homogeneous surface of the obtained VN. The CV diagrams illustrate the existence of fast and reversible redox reactions on the surface of VN electrode. The specific capacitance of VN is 161 F g⁻¹ at 30 mV s⁻¹. Furthermore, the specific capacitance remains 70% of the original value when the scan rate increases from 30 to 300 mV s⁻¹. CD experiments show that VN is suitable for CD at high current density, and the slow and irreversible faradic reactions exist during the charge-discharge process of the VN electrode. The experimental results indicate that VN is a promising electrode material for electrochemical supercapacitors.     

Synthesis and characterization of the SnO2-pillared layered titanate nanohybrid

SnO₂-pillared titanate nanohybrid has been prepared by reacting the exfoliated layered titanate sheets with the nanosized SnO₂ sol particles. The stable two-dimensional colloidal nanosheets could be obtained by intercalating tetrabutylammonium cation into the layered protonic titanate, H_xTi_2−x/4□_x/4O₄·H₂O (x=0.67) with a lepidocrocite-like structure, and by successive exfoliation process in an aqueous solution. Monodispersed SnO₂ nano sol particles were prepared by hydrolysis of SnCl₄·5H₂O in the presence of sodium hydroxide, and then the exfoliated titanate suspension was mixed with SnO₂ nano sol solution until the flocculated products formed. The final product was heated at various temperatures in order to complete the grafting reaction of intercalated SnO₂ nano sol on the interlayer surface of layered titanate. Inductive coupled plasma, X-ray diffraction, thermal analysis and N₂-adsorption-desorption isotherms were carried out to study the hybridizing process and the structure of SnO₂-pillared titanate nanohybrid.