Low-temperature thermoelectric properties of Bi85Sb15−xNbx alloys prepared by high-press sintering

The nanocrystalline materials with the general formula Bi₈₅Sb_15−xNb_x (x=0, 0.5, 1, 2, 3) were prepared by mechanical alloying and subsequent high-pressure sintering. Their transport properties involving electrical conductivity, Seebeck coefficient and thermal conductivity have been investigated in the temperature range of 80-300 K. The absolute value of Seebeck coefficient of Bi₈₅Sb₁₃Nb₂ reaches a maximum of 161 μV/K at 105 K, which is 69% larger than that of Bi₈₅Sb₁₅ at the same temperature. The power factor and figure-of-merit are 4.45×10⁻³ WK⁻²m⁻¹ at 220 K and 1.79×10⁻³ K⁻¹ at 196 K, respectively. These results suggest that thermoelectric properties of Bi₈₅Sb₁₅ based material can be improved by Nb doping.     

Temperature dependence of thermoelectric properties of Ni-doped CoSb3

Temperature dependences of the Hall coefficient, Hall mobility and thermoelectric properties of Ni-doped CoSb₃ have been characterized over the temperature range from 20 to 773 K. Ni-doped CoSb₃ is an n-type semiconductor and the conduction type changes from n-type to p-type at around 450 K. The temperature for the transition from n-type to p-type increased with increasing Ni content x. The Seebeck coefficient reaches a maximum value near the transition temperature. The electrical resistivity indicates that Co_1−xNi_xSb₃ is a typical semiconductor when x≤0.03 and a degenerate semiconductor when x>0.03. Thermal conductivity analyses show that the lattice component is predominant at lower temperatures and carrier and bipolar components become large at temperatures higher than the transition temperature. The thermoelectric figure of merit reaches a maximum value close to the transition temperature and the largest value, 4.67×10⁻⁴ K⁻¹ at 600 K, was obtained for x=0.05.     

Structure and low-temperature properties of Ba8Ni6Ge40

Structural, magnetic, heat capacity, electrical and thermal transport properties are reported on polycrystalline Ba₈Ni₆Ge₄₀. Ba₈Ni₆Ge₄₀ crystallizes in a cubic type I clathrate structure with unit cell a=10.5179 (4) Å. It is diamagnetic with susceptibility χ_dia=−1.71×10^-6 emu/g Oe. An Einstein temperature 75 K and a Debye temperature 307 K are estimated from heat capacity data. It exhibits n-type conducting behavior below 300 K. It shows high Seebeck coefficients (−111×10^-6 V/K), low thermal conductivity (2.25 W/K m), and low electrical resistivity (8.8 mΩ cm) at 300 K.     

Thermoelectric performance of ternary Bi-Sb-Ag alloys prepared by mechanical alloying and subsequent pressureless sintering

The alloys with the general formula of Bi₈₅Sb_15−xAg_x (x=0, 1, 3, 5, 7) were prepared by mechanical alloying and subsequent pressureless sintering (Bi₈₅Sb₁₅ alloy was used for comparison). Their transport properties involving electrical conductivity, Seebeck coefficient, and thermal conductivity had been investigated in the temperature range of 80-300 K. The maximum absolute value of Seebeck coefficient (120 μV/K) was found at 160 K in the alloy Bi₈₅Sb_15−xAg_x (x=3). The figure-of-merit of alloy Bi₈₅Sb_15−xAg_x (x=1) reached a maximum value of 2.16×10⁻³ K⁻¹ at 219 K, which is as large again as that of the reference sample Bi₈₅Sb₁₅.     

Defect formation and transport in mixed-conducting La0.90Sr0.10Al0.85−xFexMg0.15O3−δ

The redox behavior of perovskite-type La_0.90Sr_0.10Al_0.85−xFe_xMg_0.15O_3−δ (x=0.20-0.40) mixed conductors was analyzed by the Mössbauer spectroscopy and measurements of the total conductivity and Seebeck coefficient in the oxygen partial pressure range from 10⁻²⁰ to 0.5 atm at 1023-1223 K. The results combined with oxygen-ion transference numbers determined by the faradaic efficiency technique in air, were used to calculate defect concentrations, mobilities, and partial ionic and p- and n-type electronic conductivities as a function of oxygen pressure. The redox and transport processes can be adequately described in terms of oxygen intercalation and iron disproportionation reactions, with the thermodynamic functions independent of defect concentrations. No essential delocalization of the electronic charge carriers was found. The oxygen non-stoichiometry values estimated from the conductivity vs. p(O₂) dependencies, coincide with those evaluated from the Mössbauer spectra.     

Effect of varying mixture ratio of raw material powders on the thermoelectric properties of AlMgB14-based materials prepared by spark plasma sintering

Thermoelectric properties of AlMgB₁₄-based materials prepared by spark plasma sintering were investigated. Al, Mg, and B powders were used as raw material powders. The raw powders were mixed using a V-shaped mixer, and then the mixture was sintered at 1673 K or 1773 K. The mixture ratio of raw powders was varied around stoichiometric ratio of AlMgB₁₄. X-ray diffraction patterns of samples showed that all samples consist of AlMgB₁₄ and MgAl₂O₄. The Seebeck coefficient of the samples exhibited significant change depending on the varying mixture ratio and sintering temperature. One sample exhibited a large negative value for the Seebeck coefficient (approximately −500 μV/K) in the temperature range from 573 K to 1073 K, while others showed positive value (250–450 μV/K). Thus n-type AlMgB₁₄-based material has been realized by varying raw material ratio and sintering temperature.     

Transport coefficients and defect structure of Sb2−xAgxTe3 single crystals

Incorporation of Ag in the crystal lattice of Sb₂Te₃ creates structural defects that have a strong influence on the transport properties. Single crystals of Sb_2−xAg_xTe₃ (x=0.0; 0.014; 0.018 and 0.022) were characterized by measurements of the temperature dependence of the electrical resistivity, Hall coefficient, Seebeck coefficient and thermal conductivity in the temperature range of 5-300 K. With an increasing content of Ag the electrical resistance, the Hall coefficient and the Seebeck coefficient all decrease. This implies that the incorporation of Ag atoms in the Sb₂Te₃ crystal structure results in an increasing concentration of holes. However, the doping efficiency of Ag appears to be only about 50% of the expected value. We explain this discrepancy by a model based on the interaction of Ag impurity with the native defects in the Sb_2−xAg_xTe₃ crystal lattice. Defects have a particularly strong influence on the thermal conductivity. We analyze the temperature dependence of the lattice thermal conductivity in the context of the Debye model. Of the various phonon scattering contributions, the dominant influence of Ag incorporation in the crystal lattice of Sb₂Te₃ is revealed to be point-defect scattering where both the mass defect and elastic strain play a pivotal role.     

Chemical spray pyrolysis deposition and characterization of p-type CuCr1−xMgxO2 transparent oxide semiconductor thin films

A chemical spray pyrolysis technique for deposition of p-type Mg-doped CuCrO₂ transparent oxide semiconductor thin films using metaloorganic precursors is described. As-deposited films contain mixed spinel CuCr₂O₄ and delafossite CuCrO₂ structural phases. Reduction in spinel CuCr₂O₄ fraction and formation of highly crystalline films with single phase delafossite CuCrO₂ structure is realized by annealing at temperatures ?700 °C in argon. A mechanism of synthesis of CuCrO₂ films involving precursor decomposition, oxidation and reaction between constituent oxides in the spray deposition process is presented. Post-annealed CuCr_0.93Mg_0.07O₂ thin films show high (?80%) visible transmittance and sharp absorption at band gap energy with direct and indirect optical band gaps 3.11 and 2.58 eV, respectively. Lower (∼450 °C) substrate temperature formed films are amorphous and yield lower direct (2.96 eV) and indirect (2.23 eV) band gaps after crystallization. Electrical conductivity of CuCr_0.93 Mg_0.07O₂ thin films ranged 0.6-1 S cm⁻¹ and hole concentration ∼2×10¹⁹ cm⁻³ determined from Seebeck analysis. Temperature dependence of conductivity exhibit activation energies ∼0.11 eV in 300-470 K and ∼0.23 eV in ?470 K region ascribed to activated conduction and grain boundary trap assisted conduction, respectively. Heterojunction diodes of the structure Au/n-(ZnO)/p-(CuCr_0.93Mg_0.07O₂)/SnO₂ (TCO) were fabricated which show potential for transparent wide band gap junction device.     

Thermoelectric properties of the Bi2−xYxRu2O7 (x=0-2) pyrochlores

Electrical conductivity and Seebeck coefficient for the Bi_2−xY_xRu₂O₇ pyrochlores with x=0.0,0.5,1.0,1.5,2.0 were measured in the temperature range of 473-1073 K in air. With increasing Bi content, the temperature dependence of the electrical conductivity changed from semiconducting to metallic. The signs of the Seebeck coefficient were positive in the measured temperature range for all the samples, indicating that the major carriers were holes. The temperature dependence of the Seebeck coefficient for the Y₂Ru₂O₇ indicated the thermal activation-type behavior of the holes, while that for the Bi_2−xY_xRu₂O₇ with x=0.0-1.5 indicated the itinerant behavior of the holes. The change in the conduction behavior from semiconductor to metal with increasing Bi content is consistent with the increase in the overlap between the Ru4d t_2g and O2p orbitals, but the mixing of Bi6s, 6p states at E_F may not be ruled out. The thermoelectric power factors for the Bi_2−xY_xRu₂O₇ with x=1.5 and 2.0 were lower than 10⁻⁵ W m⁻¹ K⁻² and those with x=0.0,0.5,1.0 were around 1-3×10⁻⁵ W m⁻¹ K⁻².     

High temperature thermoelectric properties of Nb-doped ZnO ceramics

Solid-state reaction processing technique was used to prepare Zn_xNb_1−xO (0≤x≤0.02) polycrystalline bulk samples. In the present study, we find that their lattice parameters a and c tend to decrease with increasing amount of Nb additive. The electrical conductivity of all the Zn_1−xNb_xO samples increased with increasing temperature, indicating a semiconducting behavior in the measured temperature range. The addition of Nb₂O₅ to ZnO led to an increase in the electrical conductivity and a decrease in the absolute value of the Seebeck coefficient. The best performance at 1000 K has been observed for nominal 0.5 at% Nb-doped ZnO, with an electrical resistivity of about 73.13 (S cm⁻¹) and Seebeck coefficient of ∼257.36 μV K⁻¹, corresponding to a power factor (S²σ) of 4.84×10⁻⁴ Wm⁻¹ K⁻². The thermal conductivity, κ, of the oxide decreased as compared to pure ZnO. The figure of merit ZT values of ZnO-doped Nb₂O₅ samples are higher than the ZnO pure sample, demonstrating that the Nb₂O₅ addition is fairly effective for enhancing thermoelectric properties.     

MgB2 fabrication by diffusion-controlled three layered (B-Mg-B) technique

MgB₂ was successfully fabricated through diffusion-controlled three-layered (B-Mg-B) technique under high pressure. Due to melting temperature of Mg, the material was pre-heat treated at 600 °C between 1 and 48 h. Optimum pre-heat treatment condition was found to be 600 °C for 48 h. Then, the compacted material was grinded and pelletized under pressure of 2 ton. The pellets were heat treated at 600-900 °C for 1-48 h. Optimum heat treatment condition was determined to be 800 °C for 1 h for formation of almost pure MgB₂. Diffusion coefficient was determined with Fick's law and EDX data. Diffusion coefficient value for B in Mg matrix and Mg in B matrix was determined to be 1.66×10⁻⁷ and 3.14×10⁻⁸ cm²/sn, respectively. Best T_c value (39.4 K) was obtained for material heat treated at 800 °C for 1 h. A symmetric hysteresis was obtained for the best MgB₂ material and magnetization decreased with increase in the temperature and the applied magnetic field.     

Optical and thermoelectric characterizations of electroplated n-Bi2(Te0.9Se0.1)3

Bismuth selenotelluride (Bi₂(Te_0.9Se_0.1)₃) films were electrodeposited at constant current density from acidic aqueous solutions with Arabic gum in order to produce thin films for miniaturized thermoelectric devices. X-ray fluorescence spectroscopy determined film compositions. X-ray diffraction pattern shows that the films as deposited are polycrystalline, isostructural to Bi₂Te₃ and covered by crystallites. Mueller-matrix analysis reveals that the electroplated layers are optically like an isotropic medium. Their pseudo-dielectric functions were determined using mid-infrared spectroscopic ellipsometry. Tauc-Lorentz combined with Drude dispersion relations were successfully used. The energy band gap E_g was found to be about 0.15 eV. Moreover, the fundamental absorption edge was described by an indirect optical band-to-band transition. From Seebeck coefficient measurement, films exhibit n-type charge carrier and the value of thermoelectric power is about −40 μV/K.     

Influence of negative pressure on thermoelectric properties of Sb2Te3

We investigated the influence of negative pressure on the electrical conductivity, the Seebeck coefficient, and the power factor of Sb₂Te₃. We performed first-principles calculations with the linearized-augmented plane-wave method considering negative hydrostatic pressure in the range from zero to −2 GPa and doping for electrons and holes up to 10²⁰ cm⁻³. Our results predict a significant increase of the Seebeck coefficient and the power factor under negative pressure for certain doping concentrations.     

Crystal structure,NMR study,dielectric relaxation and AC conductivity of a new compound [Cd3(SCN)2Br6(C2H9N2)2]n

The crystal structure, the ¹³C NMR spectroscopy and the complex impedance have been carried out on [Cd₃(SCN)₂Br₆(C₂H₉N₂)₂]_n. Crystal structure shows a 2D polymeric network built up of two crystallographically independent cadmium atoms with two different octahedral coordinations. This compound exhibits a phase transition at (T=355±2 K) which has been characterized by differential scanning calorimetry (DSC), X-rays powder diffraction, AC conductivity and dielectric measurements. Examination of ¹³C CP/MAS line shapes shows indirect spin–spin coupling (¹⁴N and ¹³C) with a dipolar coupling constant of 1339 Hz. The AC conductivity of this compound has been carried out in the temperature range 325–376 K and the frequency range from 10⁻² Hz to 10 MHz. The impedance data were well fitted to two equivalent electrical circuits. The results of the modulus study reveal the presence of two distinct relaxation processes. One, at low frequency side, is thermally activated due to the ionic conduction of the crystal and the other, at higher frequency side, gradually disappears when temperature reaches 355 K which is attributed to the localized dipoles in the crystal. Moreover, the temperature dependence of DC-conductivity in both phases follows the Arrhenius law and the frequency dependence of σ(ω,T) follows Jonscher's universal law. The near values of activation energies obtained from the conductivity data and impedance confirm that the transport is through the ion hopping mechanism.     

Oxygen nonstoichiometry, Mössbauer spectra and mixed conductivity of Pr0.5Sr0.5FeO3−δ

The oxygen deficiency of perovskite-type Pr_0.5Sr_0.5FeO_3−δ, studied by coulometric titration, thermogravimetry and Mössbauer spectroscopy, is significantly higher than that in La_0.5Sr_0.5FeO_3−δ at 973-1223 K. The variations of hole mobility and Seebeck coefficient in oxidizing atmospheres, where the total conductivity of praseodymium-strontium ferrite is predominantly p-type electronic, suggest progressive delocalization of the p-type charge carriers on increasing oxygen chemical potential. As for other perovskite-type ferrites, reduction leads to the co-existence of vacancy-ordered and disordered domains. The n-type electronic conductivity of Pr_0.5Sr_0.5FeO_3−δ at reduced p(O₂) and the hole transport under oxidizing conditions are both lower compared to the La-containing analogue. Analogous conclusion was drawn for the ionic conductivity, calculated from the steady-state oxygen permeation data under oxidizing conditions and from the p(O₂)-dependencies of total conductivity in the vicinity of electron-hole equilibrium points where the average iron oxidation state is 3+. The similar activation energies for partial ionic and electronic conductivities in Ln_0.5Sr_0.5FeO_3−δ (Ln=La, Pr) indicate that the presence of praseodymium does not alter any of the conduction mechanisms but decreases the charge-carrier mobility due to the smaller radius of Pr³⁺ cations stabilized in the perovskite lattice.     

Annealing temperature influence on electrical properties of ion beam sputtered Bi2Te3 thin films

Ion beam sputtering process was used to deposit n-type fine-grained Bi₂Te₃ thin films on BK7 glass substrates at room temperature. In order to enhance the thermoelectric properties, thin films are annealed at the temperatures ranging from 100 to 400 °C. X-ray diffraction (XRD) shows that the films have preferred orientations in the c-axis direction. It is confirmed that grain growth and crystallization along the c-axis are enhanced as the annealing temperature increased. However, broad impurity peaks related to some oxygen traces increase when the annealing temperature reached 400 °C. Thermoelectric properties of Bi₂Te₃ thin films were investigated at room temperature. The Bi₂Te₃ thin films, including as-deposited, exhibit the Seebeck coefficients of −90 to −168 μV K⁻¹ and the electrical conductivities of 3.92×10²-7.20×10² S cm⁻¹ after annealing. The Bi₂Te₃ film with a maximum power factor of 1.10×10⁻³ Wm⁻¹ K⁻² is achieved when annealed at 300 °C. As a result, both structural and transport properties have been found to be strongly affected by annealing treatment. It was considered that the annealing conditions reduce the number of potential scattering sites at grain boundaries and defects, thus improving the thermoelectric properties.     

Synthesis, physical and photo electrochemical characterization of La-doped SrSnO3

The transport properties of Sr_0.98La_0.02SnO_3−δ in the system Sr_1−xLa_xSnO_3−δ, after which the pyrochlore La₂Sn₂O₇ appears, were investigated over the temperature range 4.2-300 K. The oxide was found to be n-type semiconductor with concomitant reduction of Sn⁴⁺ into Sn²⁺. The magnetic susceptibility was measured down to 4.2 K and is less than 3×10⁻⁵ emu cgs mol⁻¹ consistent with itinerant electron behavior. The electron is believed to travel in a narrow band of Sn:5s character with an effective mass ∼4 m_o. The highest band gap is 4.32 eV and the optical transition is directly allowed. A further indirect transition occurs at 4.04 eV. The electrical conductivity follows an Arrhenius-type law with a thermal activation of 40 meV and occurs by small polaron hopping between nominal states Sn^4+/2+. The linear increase of thermo-power with temperature yields an electron mobility μ_300 K (2×10⁻⁴ cm² V⁻¹ s⁻¹) thermally activated. The insulating-metal transition seems to be of Anderson type resulting from random positions of lanthanum sites and oxygen vacancies. At low temperatures, the conduction mechanism changes to a variable range hopping with a linear plot Ln ρ⁻¹ vs. T⁻⁴. The photo electrochemical (PEC) measurements confirm the n-type conductivity and give an onset potential of −0.46 V_SCE in KOH (1 M). The Mott-Schottky plot C⁻²-V shows a linear behavior from which the flat band potential V_fb=+0.01 V_SCE at pH 7 and the doping density N_D=1.04×10²¹ cm⁻³ were determined.     

Annealing effects on the structural and electrical transport properties of n-type Bi2Te2.7Se0.3 thin films deposited by flash evaporation

N-type Bi₂Te_2.7Se_0.3 thermoelectric thin films with thickness 800 nm have been deposited on glass substrates by flash evaporation method at 473 K. Annealing effects on the thermoelectric properties of Bi₂Te_2.7Se_0.3 thin films were examined in the temperature range 373-573 K. The structures, morphology and chemical composition of the thin films were characterized by X-ray diffraction, field emission scanning electron microscope and energy dispersive X-ray spectroscopy, respectively. Thermoelectric properties of the thin films have been evaluated by measurements of the electrical resistivity and Seebeck coefficient at 300 K. The Hall coefficients were measured at room temperature by the Van der Pauw method. The carrier concentration and mobility were calculated from the Hall coefficient. The films thickness of the annealed samples was measured by ellipsometer. When annealed at 473 K, the electrical resistivity and Seebeck coefficient are 2.7 mΩ cm and −180 μV/K, respectively. The maximum of thermoelectric power factor is enhanced to 12 μW/cm K².     

Electron hopping mechanism in hematite (α-Fe2O3)

The frequency dependence of the real (?′) and imaginary (?″) parts of the dielectric constant of polycrystalline hematite (α-Fe₂O₃) has been investigated in the frequency range 0-100 kHz and the temperature range 190-350 K, in order to reveal experimentally the electron hopping mechanism that takes place during the Morin transition of spin-flip process. The dielectric behaviour is described well by the Debye-type relaxation (α-dispersion) in the temperature regions T<233 K and T>338 K. In the intermediate temperature range 233 K<T<338 K a charge carrier mechanism takes place (electron jump from the O²⁻ ion into one of the magnetic ions Fe³⁺) which gives rise to the low frequency conductivity and to the Ω-dispersion. The temperature dependence of relaxation time (τ) in the −ln τ vs 10³/T plot shows two linear regions. In the first, T<238 K, τ increases with increasing T implying a negative activation energy −0.01 eV, and in the second region T>318 K τ decreases as the temperature increases implying a positive activation energy 0.12 eV. The total reorganization energy (0.12-0.01) 0.11 eV is in agreement with the adiabatic activation energy 0.11 eV given by an ab initio model in the literature. The temperature dependence of the phase shift in the frequencies 1, 5, 10 kHz applied shows clearly an average Morin temperature T_Mo=284±1 K that is higher than the value of 263 K corresponding to a single crystal due to the size and shape of material grains.     

Thermal, electrical, and electrochemical properties of Lanthanum-doped Ba0.5Sr0.5 Co0.8Fe0.2O3-δ

Crystal structure, thermogravimetry (TG), thermal expansion coefficient (TEC), electrical conductivity and AC impedance of (Ba_0.5Sr_0.5)_1-xLa_xCo_0.8Fe_0.2O_3-δ (BSLCF; 0.05?x?0.20) were studied in relation to their potential use as intermediate temperature solid oxide fuel cell (IT-SOFC) cathode. A single cubic pervoskite was observed by X-ray diffraction (XRD). The TEC of BSLCF was increasing slightly with the increasing content of La, and all the compounds showed abnormal expansion at high temperature. Proved by the TG result, it was associated with the loss of lattice oxygen. The electrical conductivity, which is the main defect of Ba_0.5Sr_0.5 Co_0.8Fe_0.2O_3-δ (BSCF), was improved by La doping, e.g., the compound of x=0.20 demonstrated a conductivity of σ=376 S cm⁻¹ at 392 °C. The increase of electrical conductivity resulted from the increased concentration of charge carrier induced by La doping. In addition, the AC impedance revealed the better electrochemical performance of BSLCF. For example, at 500 °C, the sample with composition x=0.15 yielded the resistance values of 2.12 Ω cm², which was only 46% of BSCF.