Vapor pressures and osmotic coefficients of the acetone solutions of three bis(tetraalkylammonium)tetrathiomolybdates at 298.15 K measured by head-space gas chromatography

The vapor pressures and osmotic coefficients of solutions of (R₄N)₂[MoS₄] (R = ethyl, n-propyl and n-butyl) in acetone have been measured by head space-gas chromatography (HS-GC). Experimental data for the osmotic coefficients have been expressed by three thermodynamic models including the ionic interaction model of Pitzer, the electrolyte non-random two liquid (e-NRTL) model and the non-random factor (NRF) model. The ability of the models to fit the osmotic coefficient was compared on the basis of the standard deviation of the fittings. The results show that the considered models provide reliable results, but the Pitzer's model gives better results than the NRTL and the NRF methods, especially in the dilute region.     

Densities and apparent molal volumes of aqueous CaCl2 and MgCl2 solutions

The Pitzer ion interaction model has been used to evaluate literature data for the densities of aqueous CaCl₂ and MgCl₂ solutions between 0 and 100°C. The selected data can be adequately fitted by setting ^(1),v equal to zero. The variations of ^(0),v and C ^v with temperature have been found to be linearly correlated. The uncertainty in the calculated density is lower than 50 ppm below 1M but raises to 300 ppm at high concentrations. When plotted vs. the square root of the molality, the apparent molal volume of MgCl₂ shows a change at a concentration where a transition in the speed of sound has already been reported by Millero, et al.     

Enthalpies of solution,partial molal heat capacities and apparent molal volumes of sugars and polyols in water

Integral enthalpies of solution of some sugars and polyols in water at low concentrations have been determined calorimetrically at 25 and 35°C. These data have been used to derive heat capacities of solution C°_p at 30°C. Partial molal heat capacities C°_p,2 have been obtained by combining C°_p with C _p,2 ^* , the heat capacity of pure solid compounds. Apparent molal volumes have been obtained from density data. The sugars as well as polyols show significantly high positive C°_p and C°_p,2 values. The results have been explained in terms of a specific hydration model. The effect of substitution of-OH by glycosidic-OCH₃ and of-CHOH by deoxy-CH₂ are also discussed.     

Apparent molal volumes and heat capacities of some 1:1 electrolytes in anhydrous methanol at 25°C

A flow calorimeter and flow densimeter have been used to measure volume specific heats and densities of solutions of LiCl, LiBr, NaCl, NaBr, KF, KBr, Kl, CsF, and Bu₄NBr in anhydrous methanol at 25°C. The concentrations ranged from approximately 0.01m to close to saturation in some cases. Apparent molal heat capacities _cp and volumes _v have been evaluated and extrapolated to infinite dilution to obtain _cp ^o and _v ^o . Nearly all the heat capacities in methanol are negative. However, with the exception of the lithium halides and Bu₄NBr they are more positive than heat capacities of the corresponding salts in water. The dependence of the heat capacities on ionic radii is generally opposite in methanol solutions from that observed for aqueous solutions. In agreement with others, the _v ^o data indicate that electrostriction in methanol solutions is greater than in aqueous solutions.     

Apparent molal volumes and adiabatic compressibilities of ethylene glycol derivatives in water at 5, 25, and 45°C

Density and ultrasonic velocity measurements were made on a series of dilute equeous solutions of H(OCH ₂ CH ₂ )_nOH, CH ₃ (OCH ₂ CH ₂ )_nOCH ₃ , H(CH ₂ )_nOCH ₂ CH ₂ OH (n=1–4), and poly(ethylene glycol) at 5, 25, and 45°C. The additivity of the limiting partial molal volumes ( ) and adiabatic compressibilities ( ) for CH ₂ and CH ₂ CH ₂ O groups was tested by using the observed and values of the solutes. The and values of the CH ₃ , CH ₂ , CH ₂ CH ₂ O, and CH ₂ OH groups were estimated and discussed in relation to hydration effects. The and values of alkoxyethanols calculated on the basis of the additivity of the group partial molal quantities were in good agreement with the observed values. The behavior of the limiting partial molal isothermal compressibility of alkoxyethanols was similar to that of the adiabatic compressibility.     

Apparent molal volumes of aqueous solutions of bis-tetraalkylammonium salts at 25°C: Methylene-group contribution to the limiting molal volume

Densities of aqueous solutions of a series of polymethonium chloride and bromide salts (CH₃)₃–N–(CH₂)_n–N–(CH₃)₃X₂ have been measured at 25°C. Apparent molal volumes have been calculated, and methylene-group contributions to the limiting apparent molal volumes °_v have been estimated. Constant values of the methylene-group contribution of 16.5 and 17.0 cm³-mole^–1 were obtained for the bromide and chloride salts, respectively. These values are consistent with methylene-group contributions reported for other series of organic electrolytes.     

Apparent molal heat capacities and volumes of pyridine and methyl-substituted pyridines in aqueous solution at 25°C

We have made calorimetric measurements leading to apparent molal heat capacities of pyridine and four methyl-substituted pyridines in aqueous solution at 25.0°C. Measurements of densities of the same solutions have led to apparent molal volumes. The results are as follows: pyridine, _C ^° = 305.7 J–°K^–1-mole^–1 and _V ^° = 77.5 cm³-mole^–1; 2-methylpyridine, _C ^° = 370.0 J–°K^–1-mole^–1 and _V ^° = 94.3 cm³-mole^–1; 3-methylpyridine, _C ^° = 380.2 J–°K^–1-mole^–1 and _V ^° = 93.7 cm³-mole^–1; 4-methylpyridine, _C ^° = 378.9 J–°K^–1-mole^–1 and _V ^° = 94.3 cm³-mole^–1; 2,6-dimethylpyridine, _C ^° = 441.8 J–°K^–1-mole^–1 and _V ^° = 109.9 cm³-mole^–1. These _C ^° and _V ^° values are discussed in terms of effects of substitution of CH₃-for H– in the various solute molecules.The research reported here was carried out in the Department of Chemistry, University of Lethbridge, Lethbridge, Alberta, Canada T1K 3M4.     

Isopiestic determination of osmotic and activity coefficients of aqueous solutions of aliphatic polyols at 298.15 K

The osmotic coefficients of 1,2-butanediol (12BD), 1,3-butanediol (13BD), 1,4-butanediol (14BD), 2,3-butanediol (23BD), 1,2,4-butanetriol (124BT) and 1,2,3,4-butanetetrol (1234BT) in water were measured by the isopiestic method at 298.15 K. Experimental osmotic coefficients were used to calculate water activity, solute activity coefficients and the pairwise Gibbs energy coefficients for solute–solute interactions.     

Thermodynamic properties of the system NH4NO3 + (NH4)2SO4 + H2O at 298.15 K

In this investigation, the mixed aqueous electrolyte system of nitrate and sulfate with common ammonium cation has been studied with the hygrometric method at the temperature 298.15 K. The water activities of the system [yNH₄NO₃ + (1 − y)(NH₄)₂SO₄](aq) are measured at total molalities from 0.4 mol kg⁻¹ up to saturation for different ionic-strength fractions y of NH₄NO₃ with y = 0.2, 0.5 and 0.8. The obtained data allow the deduction of osmotic coefficients. The experimental results are compared with the predictions of the Zdanovskii–Stokes–Robinson (ZSR), Leitzke and Stoughton (LSII), Kusik and Meissner (KM), and Pitzer models. From these measurements, new Pitzer mixing ionic parameters are determined and used to predict the solute activity coefficients in the mixture. The obtained results are used to calculate the excess Gibbs energy at total molalities for different ionic-strength fractions y.     

等压法测定298.15K下LiCl-CaCl2-H2O体系的活度系数

电解质水溶液热力学性质的研究一直是一个很活跃的研究领域.对含锂水盐体系热力学性质的研究不仅对电解质水溶液理论,而且对盐湖锂资源的开放利用都有非常重要的意义.姚燕等对ＬｉＣｌＫＣｌＨ2Ｏ[1],ＬｉＣｌＭｇＣｌ2Ｈ2Ｏ[2],ＬｉＣｌＭｇＳＯ4Ｈ2Ｏ[3,4],ＬｉＣｌＬｉ2ＳＯ4Ｈ2Ｏ[5]体系多温下热力学性质进行了研究,应用Ｐｉｔｚｅｒ电解质水溶液理论模型进行处理,计算出ＬｉＣｌ在不同体系中,很大的浓度范围内的活度系数.但在盐湖卤水中,ＣａＣｌ2的存在很普遍.对ＬｉＣｌＣａＣｌ2混合物在水溶液中的热力学性质研究对理解ＬｉＣｌ在盐…     

ZnCl_2溶液中微波辅助SnCl_4催化纤维素制备5-HMF

将纤维素溶解在ZnCl_2溶液中,以SnCl_4为催化剂,微波下使纤维素降解成5-羟甲基糠醛(5-HMF)。实验考察了微波功率、纤维素的质量、ZnCl_2溶液浓度、反应时间及催化剂与纤维素物质的量比等对5-HMF产率的影响。结果表明,以SnCl_4为催化剂,在优化条件:1.0 g纤维素溶解在100 m L 70%ZnCl_2溶液中,微波功率为420 W,降解反应9 min,SnCl_4与纤维素物质的量比2∶1下,5-HMF的产率达到39.4%。     

微波辐射促进ZnCl2与Y分子筛固相反应的研究

ZnCl2/Y catalysts prepared by solid-state reaction of anhydrous ZnCl2 and Y zeolites under microwave irradiation were characterized by XRD, IR and AAS. ZnCl2 was intercalated in Y zeolites and dispersed on the surface of Y zeolite, part of ZnCl2 dispersed could result in solid-state ion exchange with Y. The amount of dispersion and solid-state ion exchange were related to ZnCl2 loading and the surface acid property of the zeolite. When ZnCl2 loading was 37.5% (mass fraction) in NaY zeolite, ZnCl2 was still completely dispersed on the surf are of zeolite and the degree of solid- state ion exchang was 84%. The appearance of new band at 890 cm-l in the framework IR spectra of ZnCl2/NaY sample was due to the dispersed ZnCl2 coordinating strongly with oxygen of NaY surface. With the increasing of the number of arid centers and the acid strength of the surface of Y zeolite the amount of solid-state ion exchange decreased.     

Densities and apparent molal volumes of aqueous concentrated calcium chloride solutions from 50 to 200°C at 20.27 bar

Densities of aqueous calcium chloride solutions are reported for molalities up to 6.4 mol-kg^–1 at temperatures from 50 to 200°C and at 20.27 bar. Apparent molar volumes calculated from experimental densities were fitted to the equations of Rogers and Pitzer, and the temperature dependence of the Pitzer parameters were obtained. The standard deviation of fit for the apparent molar volumes is 0.21 cm³-mol^–1 from 50 to 200°C at 20.27 bar.     

298.15K下Li2B4O7-H2O体系水蒸汽分压及渗透系数的等压测定和离子相互作用模型

在已有研究含硼体系的文献中仅考虑了硼酸根B4O7^-2或B(OH)4^-和H3BO3的存在，而对Li2B4O7-H2O体系具有多种硼物种聚合平衡体系的热力学性质的研究尚未见报道．本文用等压法研究了Li2B4O7-H2O体系于298．15K下浓度由稀到过饱和溶液的平衡气相蒸汽压及渗透系数．考虑了水溶液中多种硼物种的存在，以Pitzer方程为基础，建立了可描述该含硼体系的离子相互作用模型。     

Group additivity for the standard partial molal heat capacities and volumes of polar compounds in methanol at 25°C

A flow heat capcity calorimeter and a flow vibrating tube densimeter have been used to measure the apparent molal heat capacities and volumes of benzene and 25 polar compounds in methanol at 25°C. These quantities have been extrapolated to infinite dilution to obtain the standard partial molal heat capacities and volumes. The and data have been used in conjunction with an additivity scheme previously determined for alkanes. Group contributions were evaluatd for –OH, –NH₂, –COOH, –C₆H₅, C=O, –COO–, –CONH–, –O–, –S–, and –S₂–. The concentration dependences of _cp and _v of nonelectrolytes in methanol are qualitatively similar but much smaller than in water.     

Partial molal volumes and adiabatic compressibilities of dodecylpolyoxyethylene glycol monoethers in water at 5, 25, and 45°C

Density and ultrasonic velocity measurements were made on a series of dilute aqueous solutions ofn-C ₁₂ H ₂₅ O (CH ₂ CH ₂ O) _n H (n=6,7 and 8) at 5, 25, and 45°C. The partial molal volumes (V) and adiabatic compressibilities (K)of the solutes were independent of the concentration in the micellar solutions. This finding suggests that the mode of aggregation does not change over the concentration range studied. Larger V and K were found for the CH ₂ CH ₂ groups in micelles than in water, and the micellar core was shown to be liquidlike. The V and K of the monomeric surfactants could not directly be measured because of the very low c.m.c.'s. The infinite dilution values V^° and (K^°) were, however, estimated from the V^° and K^° for the constituent groups on the basis of additivity. Thus, sharp increases were found in both V and K on micellization, which was interpreted in terms of dehydration effects.     

Isopiestic determination of the osmotic and activity coefficients of the {yKCl + (1 − y)K2HPO4}(aq) system at T = 298.15 K

The osmotic coefficients of aqueous mixtures of KCl and K₂HPO₄ have been measured at T = (298.15 ± 0.01) K by the isopiestic vapor pressure method over the range of ionic strengths from (2.3700 to 11.250) mol · kg⁻¹ using CaCl₂(aq) as the reference solution. Our new experimental results were modeled with an extended form of Pitzer’s ion-interaction model equations, both with the usual mixing terms and with Scatchard’s neutral–electrolyte mixing terms, and with the Clegg–Pitzer–Brimblecombe equations based on the mole-fraction-composition scale. There is a dearth of previously published isopiestic data for mixtures containing salts of and, consequently, no previous measurements are available for comparison with the present results. The present study yields mixing parameters for these three models that are needed for modeling the thermodynamic activities of solute components of natural waters and other complex aqueous electrolyte mixtures.     

Solution thermodynamics of first row transition elements. 3. Apparent molal volumes of aqueous ZnCl2 and Zn(CIO4)2 from 15 to 55°C and an examination of solute-solute and solute-solvent interactions

The apparent molal volumes of aqueous ZnCl₂ and Zn(ClO₄)₂ solutions have been measured from 15–55°C. The dilute solution data are extrapolated to infinite dilution using the Redlich-Meyer equation. The full concentration range data are fitted with the Pitzer formalism. The data are then compared with the data on the previously measured salts of Mn²⁺, Fe²⁺, Co²⁺, Ni²⁺, and Cu²⁺. The effect of complex ion formation is easily seen in the Cu²⁺ and Zn²⁺ salt data. A new approach to single ion volumes from salt volumes is proposed. The calculated ionic volumes at infinite dilution are compared, and it is clear that crystal field effects must be considered in any quantitative theory of transition element volumes.     

Enthalpies of solution of SrCl2 and BaCl2 in aqueous mixtures of methanol and ethanol at 298.15 K

Enthalpies of solution of alkaline earth metal chlorides have been determined in water and aqueous mixtures of methanol and ethanol, and the enthalpies of transfer obtained. Plots of standard enthalpy of solution ΔH_m^XXX vs. binary solvent composition are discussed and compared with the corresponding curve for water-methanol solutions of CaCl₂.     

(p, ρ, T) properties, and apparent molar volumes V? of ZnBr2 in methanol at T = (298.15 to 398.15) K and pressures up to p = 40 MPa

The (p, ρ, T) properties of pure methanol, the (p, ρ, T) properties and apparent molar volumes V_? of ZnBr₂ in methanol at T = (298.15 to 398.15) K and pressures up to p = 40 MPa are reported, and apparent molar volumes have been evaluated. The experimental (p, ρ, T, m) values were described by an equation of state. For the solutions the experiments were carried out at molalities m = (0.05772, 0.37852, 0.71585 and 1.95061) mol · kg⁻¹ of zinc bromide.