射频板条CO2激光器输出光束的光学变换

射频激励板条CO2激光器输出激光近场光斑近似为一条线,远场光斑为O形图样。在垂直于光束传输方向的平面内,光束在一个方向发散很大,无法用于激光加工。根据激光器不同的激光功率级别及光束尺寸,分别采用了圆柱面镜、滤波光阑、扩束望远镜等不同组合的方法,将200 W激光器输出光束变换成远场光束为Φ6、近似TEM00模的圆形光束,500 W激光器远场光束为Φ10的低阶模的圆形光束。成功用于激光切割。     

连续和重复频率激光对旋转壳体加热效率的数值模拟

 基于有效利用激光能量的目的,采用有限元分析方法分析并比较了重复频率和连续激光对旋转壳体的加热效率。数值计算结果表明：重复频率激光要比连续激光的加热效率高,而且加热效率与重复频率、占空比等有关;在平均功率密度相同的前提下,在频率相同条件下,占空比减小,温度上升加快,即加热效率随占空比的减小而增大;在相同占空比条件下,重复频率越小温度周期变化越明显,振荡峰值越大,当占空比较小时随着辐照时间的增加重复频率对加热效率影响减小。     

灯泵浦激光器输出激光稳定性实验研究

分析了灯泵浦激光器的特点以及影响其输出激光稳定性的原因,提出了在激光器谐振腔内加一个“Q开关”的方法来控制输出激光的稳定性,以氙灯泵浦的被动锁模Nd:YAG激光器为例进行了实验研究,证实了此方案是可行的.     

激光光强扰动对相干场成像降质影响理论研究

激光相干场成像系统发射多束激光,经大气传输对远程目标成像,大气湍流引起的激光束光强扰动是影响成像质量的一个关键因素.本文从湍流引起的激光束光强扰动对回波解调信号的影响关系入手,建立了激光回波光强扰动因子对相位闭合系数和成像频谱分量的降质传函理论模型;基于三光束激光相干场成像系统仿真验证了理论模型的有效性.研究表明激光相干场成像频谱分量和成像像质主要受三光束相位闭合求解算法中第二光束光强扰动影响.该研究揭示了激光回波光强扰动对成像像质的影响机理,对于分析大气湍流等引起的光强扰动降质效应和合理分配多光束光强稳定性以提高成像质量具有理论指导意义.     

An intermittent frequency offset lock of a transverse Zeeman laser to an iodine stabilized He-Ne laser

A single-mode frequency stabilized laser with modulation-free and moderate power is desired as a light source for an ultra-high resolution interferometer system and/or a rapid laser calibration system. For this purpose, we developed a new stabilized laser system that utilizes intermittent control of a 2 mW transverse Zeeman stabilized He-Ne laser (Zeeman laser) with an iodine stabilized He-Ne laser (I2 stabilized laser). Because of the intermittent control, working time of the I2 stabilized laser is reduced. The Zeeman laser has two operational modes: independent and slave mode. In the independent mode, the Zeeman laser is stabilized through control of Zeeman beat frequency. Temperature dependent drift of the oscillation frequency during the independent mode is periodically corrected by the slave operation utilizing frequency offset locking to the I2 stabilized laser. Frequency instability of the Zeeman laser in independent and slave modes is 7.7X10-11 and 2.0X10-11, respectively, at the sampling time of 100 s.     

连续波光阴极注入器的驱动激光器研究

 在连续波光阴极注入器的研究中,驱动激光器是一个关键技术,采用连续锁模振荡器的锁模输出作为种子源,用二极管连续泵浦放大,再连续倍频,可以产生符合注入器要求的激光脉冲列作为驱动激光。     

Evaluation of probe lasers employed in optical diagnostics for phase transformation of thin films during excimer laser crystallization

The stability and reliability of probe laser is an important factor affecting the inspection of the phase transformation process of Si thin films during excimer laser crystallization using in-situ time-resolved optical measurements. The changes in 2D intensity profile, peak power density, and beam wander of the commonly used helium–neon (He–Ne) and diode laser are investigated experimentally. It is found that the peak power density of He–Ne laser is higher than that of diode laser, while the total power of He–Ne laser is lower than that of diode laser. Although the instability in the peak power density of He–Ne laser will increase with increasing the operation time, the beam stability of He–Ne laser is better than that of diode laser. For long-time operation (>24 h) of optical measurements, the diode laser is a good candidate of probe laser. Conversely, the diode laser is suitable for the short-time operation (<24 h) of optical measurements because the beam-wander is higher than that of He–Ne laser.     

激光工作模式对苯氰S_1电子态高分辨光谱的影响

本文研究了不同激光工作模式对苯氰分子高分辨光谱的影响,高分辨的激光为Ar~+泵浦的cw环形染料激光经过Nd:YAG激光三步脉冲放大后倍频产生的UV光.实验发现当Nd:YAG激光的振荡级有种子光注入时,光谱呈现转动分辨的谱线,可以很好地标识为苯氰分子S_1←S_0 0_0~0跃迁的转动结构;而当Nd:YAG激光工作于多个模式(无种子光注入)时,光谱则为连续的毫无结构的谱带.由于苯氰分子S_1电子态具有较大的偶极矩,工作于多个模式下激光脉冲的峰值功率的增强产生AC Stark效应,是导致谱线加宽从而无法观测到转动分辨光谱的可能原因.     

激光工作模式对苯氰S1电子态高分辨光谱的影响

本文研究了不同激光工作模式对苯氰分子高分辨光谱的影响,高分辨的激光为Ar+泵浦的cw环形染料激光经过Nd：YAG激光三步脉冲放大后倍频产生的UV光. 实验发现当Nd：YAG激光的振荡级有种子光注入时,光谱呈现转动分辨的谱线,可以很好地标识为苯氰分子S1←S0 跃迁的转动结构;而当Nd：YAG激光工作于多个模式（无种子光注入）时,光谱则为连续的毫无结构的谱带.由于苯氰分子S1电子态具有较大的偶极矩,工作于多个模式下激光脉冲的峰值功率的增强产生AC Stark效应,是导致谱线加宽从而无法观测到转动分辨光谱的可能原因.     

大气环境下飞秒激光对铝靶烧蚀过程的研究

利用时间分辨的光阴影成像技术研究了在大气环境下飞秒激光烧蚀铝靶的动态过程. 在入射激光能量为4 mJ, 激光光斑超过1 mm时, 激光烧蚀区表面物质以近似平面冲击波形式向外喷射; 在同样激光能量下、激光光斑较小时(约0.6 mm), 激光烧蚀区以近似半球型冲击波形式向外喷射. 当激光能量比较大时(7 mJ), 发现空气的电离对于激光烧蚀靶材有着重要影响. 在光轴附近烧蚀产生的喷射物具有额外的柱状和半圆型的结构, 叠加在平面冲击波结构上.     

Synchronous Injection Locking Operation of Monolithic Diode Lasers Mode-Locked Diode Lasers

Synchronized mode-locking of monolithic mode-locked diode lasers has been demonstrated by injecting the light output from a master monolithic mode-locked diode laser. The master diode laser is a 10 GHZ hybridly mode-locked two section InGaASP quantum well laser. The slave lasers are a 10 GHz two section laser which is similar to the master laser, and a 20 GHz three section colliding pulse mode-locking laser. Both the slave lasers were greatly stabilized at 10 GHz frequency by a synchronous mode-locking mechanism under the injection of master laser pulses.     

Lasers for ICF with a Controllable Function of Mutual Coherence of Radiation

The current status of laser thermonuclear fusion research in the leading world scientific centers is characterized by the development of superhigh-power multi-channel laser facilities of megajoule pulse-energy level. The development of such laser installations operating in the pulse-repetition mode with a large number of laser beams, which are necessary for high-symmetry irradiation of a spherical thermonuclear target, is an extremely difficult physical and engineering problem. The concept of a special laser with a controllable function of mutual coherence of radiation is proposed. The studies performed demonstrate that a laser based on such a principle has a number of advantages as compared to the conventional schemes of lasers. In particular, the optical scheme of the laser is significantly simplified, and the cost of the output-energy unit is reduced by several times. The influence of radiation coherence on the homogeneity of the thermonuclear target irradiation is analyzed. The feasibility of suppressing the small-scale self-focusing without application of spatial filtration is shown. A module of the laser facility has been triggered to check the validity of the principles proposed for constructing a laser driver for power stations, and the first experimental results are reported. The possibility of controlling the coherence of laser beams used in ICF experiments without violation of the laser--target system matching is demonstrated, as well as controlling the distribution of the laser radiation intensity in the lens focus.     

光梳主动滤波放大实现锶原子光钟二级冷却光源

提出一种结合注入锁定技术的主动滤波放大方法,将光梳直接注入锁定至光栅外腔半导体激光器,产生窄线宽激光光源,该光源可以用于锶原子光钟二级冷却.实验中,将中心波长为689 nm,带宽为10 nm的光梳种子光源注入689 nm光栅式外腔半导体激光器,通过半导体增益光谱与半导体光栅外腔,从飞秒光梳的多个纵模梳齿中挑选出一个纵模模式来进行增益放大,再通过模式竞争,实现单纵模连续光输出;同时,光梳的重复频率锁定在线宽为赫兹量级的698 nm超稳激光光源上,因此,注入锁定后输出的窄线宽激光也继承了超稳激光光源的光谱特性.利用得到的输出功率为12 mW的689 nm窄线宽激光光源实现了88Sr原子光钟的二级冷却过程,最终获得温度为3μK,原子数约为5×10~6的冷原子团.该方法可拓展至原子光钟其他光源的获得,从而实现原子光钟的集成化和小型化.     

大功率激光单模光纤远距离传输的注入光纤光功率限值分析

对于大功率激光单模光纤远距离传输, 采用传统的受激拉曼散射(SRS)阈值作为注入光纤激光功率值取值过大。本文对单模光纤远距离传输过程中泵浦光和拉曼斯托克斯光(Stokes)光功率随注入光纤激光功率的变化进行仿真与理论分析。根据光纤中SRS产生的机理, 提出以拉曼Stokes光在单模光纤中传输的光功率变化曲线曲率极大值点对应的注入激光功率为限值, 对注入单模光纤光功率限值随着光纤长度变化进行仿真, 通过曲线拟合得出注入单模光纤激光功率限值公式, 并搭建实验系统进行验证。结果表明, 提出的注入单模光纤激光功率限值适用于大功率激光远距离单模光纤传输。     

用308nm准分子激光对几种卷烟用纸打标的研究

激光打标由于具有快速、精度高及非接触等优点，是激光在工业领域的又一应用。准分子激光是一种大功率高重复率的紫外激光器，与ＣＯ２、ＹＡＧ等红外激光相比，一般具有打标效率高、热效应小、图案更精密等优点。近年来国内外均对准分子激光打标进行了一些研究，主要集中在对金属、高分子聚合物及陶瓷等硬脆材料的打标的研究。本文研究了用３０８ｎｍ准分子激光对几种卷烟用纸打标。用适当能量密度的３０８ｎｍ准分子激光对印有数种颜色的烟盒纸、过滤嘴纸打标，获得了清晰可见的图案标记。分析了该打标过程的作用机理，通过实验得出了对几种不同的卷烟用纸打标的能量密度阈值条件及优化条件。     

An investigation of pulsed laser cutting of titanium alloy sheet

Subsequent welding requirement calls for high-quality laser cut surfaces in the laser cutting of bladed ring parts for aeroengines. This paper presents pulsed laser cutting of titanium alloy sheet and investigates the influences of laser cutting parameters on laser cut quality factors including heat-affected zone (HAZ), surface morphology and corrosion resistance. The thickness of HAZ lasers is studied in detail as a function of laser cutting parameters. For different assist gases the surface morphology and corrosion resistance show great differences. In comparison with air- and nitrogen-assisted laser cutting, argon-assisted laser cutting comes with unaffected surface quality and is suitable for laser cutting with subsequent welding requirement.     

棱镜色散腔XeF(C-A)蓝绿激光线宽压缩

XeF(C-A)蓝绿激光的增益系数较低,仅为0.003 cm-1,要获得高能量窄线宽激光输出有一定难度。利用色散元件棱镜开展了高单脉冲能量窄线宽激光输出实验研究,结果表明:采用凹面输出镜的情况下,激光线宽可以压缩到约2.5 nm,激光输出能量最大为3.47 J;采用平面输出镜,激光线宽压缩到约0.7 nm,激光输出能量最大为2.93 J,激光光谱调谐范围最大可达到60 nm,在460～520 nm之间。     

光束指向稳定性高精度检测方法研究北大核心CSCD

光束指向稳定性是高能激光应用研究中的一项关键指标,光束指向稳定性的检测是高能激光系统性能实现的重要环节。以长焦距聚焦反射镜与高分辨率CCD(charge coupled device)为主要元件,构建高精度的光束指向检测装置。采用灰度重心法定位光斑中心,并以理想光斑与实测光斑为例进行验证,误差小于1个像元。利用CCD高频采样,统计单位时间内光斑中心位移,获得光束指向稳定性指标,检测实例精度可达1.25μrad。该方法简便易行,测量精度高,适用于各种波长的激光光束指向检测以及其他相关参数的测量。     

激光光斑漂移的检测

针对激光光斑漂移设计了一套光斑漂移检测系统。利用该系统实现了对He-Ne激光器出射光束漂移的检测。它采用CCD摄像头和图像采集卡采集激光器输出光斑，通过专门软件对数字图像进行处理，得出光斑漂移的大小；另外，利用几何光学方法得到了激光光束在X方向、Y方向以及空间立体角上的漂移大小。分析了引起光束漂移的原因。结果表明：He-Ne激光器出射光束的指向主要受温度、环境振动、空气扰动和激光器自身结构的影响。该系统能准确地测量出激光器出射光束的漂移大小，实现光束漂移的控制。     

激光参数对红外成像系统干扰效果影响的实验研究

 针对激光对红外成像系统的干扰效果是光电对抗领域的一个研究热点,采用波长10.6 μm的CO2调谐脉冲激光器,通过漫反射板反射激光能量到像元数为320×240的多晶硅非制冷焦平面红外热像仪上进行激光干扰红外成像系统的实验。在实验中研究了干扰激光能量、重复频率、波长、光斑大小等激光参数对干扰效果的影响,并从图像质量的角度分析了激光参数对干扰效果的影响。结果表明,随着干扰激光能量密度、重复频率、波长和光斑的增大,干扰效果提高。此外,漫反射干扰的效果证明这种干扰方式是可行的,该方式可避免干扰源成为未来将出现的反辐射光电制导武器的诱饵,为CO2激光干扰装备提供一种新的战术配置方法。