Isobaric vapor–liquid equilibria of 1,1-dimethylethoxy-butane + methanol or ethanol + water at 101.32 kPa

Isobaric vapor–liquid equilibrium data (VLE) at 101.325 kPa have been determined in the miscible region for 1,1-dimethylethoxy-butane (BTBE) + methanol + water and 1,1-dimethylethoxy-butane (BTBE) + ethanol + water ternary systems, and for their constituent binary systems, methanol + BTBE and ethanol + BTBE. Both binary systems show an azeotrope at the minimum boiling point. In the ternary system BTBE + methanol + water no azeotrope has been found, however, the system BTBE + ethanol + water might form a ternary azeotrope near the top of the binodal. Thermodynamically consistent VLE data have been satisfactorily correlated using the UNIQUAC, NRTL and Wilson equations for the activity coefficient of the liquid phase. Temperature and vapor phase compositions have been compared with those calculated by the group-contribution methods of prediction ASOG, and the original and modified UNIFAC. Predicted values are not in good agreement with experimental values.     

Measurement and calculation of vapor–liquid equilibria for methanol + glycerol and ethanol + glycerol systems at 493–573 K

The vapor–liquid equilibria for methanol + glycerol and ethanol + glycerol systems were measured by a flow method at 493–573 K. The pressure conditions focused in this work were 3.03–11.02 MPa for methanol + glycerol system and 2.27–8.78 MPa for ethanol + glycerol system. The mole fractions of alcohol in vapor phase are close to unity at the pressures below 7.0 MPa for both systems. The pressures of liquid saturated lines of the liquid phase for methanol + glycerol and ethanol + glycerol systems are higher than that for the mixtures containing alcohol and biodiesel compound, methyl laurate or ethyl laurate.     

Experimental measurements of vapor–liquid equilibria at low pressure: Systems containing alcohols,esters and organic acids

In this work the vapor–liquid equilibria for nine binary mixtures (methanol + acetic acid, methanol + methyl acetate, methanol + water, methyl acetate + acetic acid, water + acetic acid, ethyl acetate + acetic acid, ethanol + acetic acid, ethanol + ethyl acetate and ethanol + water) at subatmospherical pressure (580 mmHg) is presented. Peng–Robinson Stryjek–Vera equation of state coupled with the Wong–Sandler mixing rules were used for predicting phase equilibria of these mixtures. The measurements were developed using an apparatus with recirculation that can also be employed for liquid–vapor equilibrium with chemical reaction.     

Vapor-liquid equilibria at 333.15 K and excess molar volumes and deviations in molar refractivity at 298.15 K for mixtures of diisopropyl ether, ethanol and ionic liquids

In this work, we have studied influence of ionic liquids (ILs) on the azeotrope composition for the system {diisopropyl ether (DIPE) + ethanol} using trihexyltetradecylphosphonium chloride ([P_666,14][Cl]) and trihexyltetradecylphosphonium bis(2,2,4-trimethylpentyl) phosphinate ([P_666,14][TMPP]). Isothermal vapor-liquid equilibrium data at 333.15 K are reported for the ternary systems {DIPE + ethanol + [P_666,14][Cl]} and {DIPE + ethanol + [P_666,14][TMPP]} with varying the mole fraction of ILs from 0.05 to 0.10. The experimental ternary VLE data were correlated using the Wilson equation. In addition, excess molar volumes (V^E) and deviations in molar refractivity (ΔR) data at 298.15 K are reported for the binary systems {DIPE + [P_666,14][Cl]} and {ethanol + [P_666,14][Cl]} by a digital vibrating tube densimeter and a precision digital refractometer. The V^E and ΔR were correlated by the Redlich-Kister equation.     

Densities, refractive indices and speeds of sound of the ternary mixtures (dimethyl carbonate + methanol + ethanol) and (dimethyl carbonate + methanol + 1-propanol) at T=298.15 K

Density, refractive index and speed of sound at T=298.15 K and atmospheric pressure have been measured over the entire composition range for (dimethyl carbonate (DMC) + methanol + ethanol) and (DMC + methanol + 1-propanol). Excess molar volumes, changes of refractive index on mixing and deviations in isentropic compressibility for the above systems have been calculated. The calculated quantities are further fitted to the Cibulka equation to estimate the ternary fitting parameters. Standard deviations from the regression lines are shown.     

Vapor–liquid equilibria for binary and ternary mixtures of ethanol, 2-butanone,and 2,2,4-trimethylpentane at 101.3 kPa

Vapor–liquid equilibrium (VLE) at 101.3 kPa have been determined for the ternary system ethanol + 2-butanone + 2,2,4-trimethylpentane (isooctane) and its constituent binary systems: ethanol + 2,2,4-trimethylpentane, ethanol + 2-butanone, and 2-butanone + 2,2,4-trimethylpentane. Minimum boiling azeotropes were observed for all these binary systems. No azeotropic behavior was found for the ternary system. Thermodynamic consistency tests were performed for all VLE data. The activity coefficients of the binary mixtures were satisfactorily correlated with the Wilson, NRTL, and UNIQUAC models. The models with their best-fitted binary parameters were used to predict the ternary vapor–liquid equilibrium.     

Liquid–liquid phase behaviour,liquid–liquid density,and interfacial tension of multicomponent systems at 298 K

Experimental liquid–liquid phase diagrams are presented for the multicomponent systems isooctane–benzene–(80 mass% methanol + 20 mass% water)–5 mass% isobutyl alcohol (2-methyl-1-propanol) and isooctane–benzene–(80 mass% methanol + 20 mass% water)–15 mass% isobutyl alcohol, at 298.15 K. The density and interfacial tension of conjugate phases of concentration located in the isothermal binodal have been determined at 298.15 K for the partially miscible systems: isooctane–benzene–methanol, isooctane–benzene–(80 mass% methanol + 20 mass% water), isooctane–benzene–(80 mass% methanol + 20 mass% water)–5 mass% isobutyl alcohol, and isooctane–benzene–(80 mass% methanol + 20 mass% water)–15 mass% isobutyl alcohol. The experimental tie-line data define the binodal or coexistence curve of the two studied multicomponent systems and depending on the initial isobutyl alcohol concentration the liquid–liquid phase diagram is either of type II, with low alcohol concentration, or type I, with high concentration of alcohol, which is a clear indication that the solubility of the partially miscible systems is greatly enhanced via the co-solvency phenomenon. It is observed that both the density of each conjugate phase and the interfacial tension of each tie-line are valuable indicators of the degree of solubility of the multicomponent systems. Furthermore the experimental tie-lines data were correlated with the NRTL and UNIQUAC solution models with satisfactory quantitative results.     

Isothermal vapor–liquid equilibrium at 333.15 K and excess molar volumes and refractive indices at 298.15 K for the mixtures of di-methyl carbonate,ethanol and 2,2,4-trimethylpentane

Isothermal vapor–liquid equilibrium data at 333.15 K are measured for the binary system ethanol + 2,2,4-trimethylpentane and for ternary system di-methyl carbonate (DMC) + ethanol + 2,2,4-trimethylpentane by using headspace gas chromatography. The experimental binary and ternary vapor–liquid equilibrium data were correlated with different activity coefficient models. Excess volume and deviations in molar refractivity data are also reported for the binary systems DMC + ethanol and DMC + 2,2,4-trimethylpentane and the ternary system DMC + ethanol + 2,2,4-trimethylpentane at 298.15 K. These data were correlated with the Redlich-Kister equation for the binary systems and the Cibulka equation for the ternary system, respectively. The ternary excess volume and deviations in molar refractivity data were also compared with estimated values from the binary contribution models of Tsao–Smith, Kohler, Rastogi and Radojkovi?.     

Isothermal vapor-liquid equilibrium at T = 333.15 K and excess volumes and molar refractivity deviation at T = 298.15 K for the ternary mixtures {di-methyl carbonate (DMC) + ethanol + benzene} and {DMC + ethanol + toluene}

Isothermal vapor-liquid equilibrium data at 333.15 K are reported for the ternary systems {di-methyl carbonate (DMC) + ethanol + benzene} and {DMC + ethanol + toluene} as determined with headspace gas chromatography. The experimental ternary vapor-liquid equilibrium (VLE) data were correlated with different activity coefficient models. The excess volume (V^E) and deviations in molar refractivity (ΔR) data are reported for the binary systems {DMC + benzene} and {DMC + toluene} and also for the ternary systems {DMC + ethanol + benzene} and {DMC + ethanol + toluene} at 298.15 K. These V^E and ΔR data were correlated with the Redlich-Kister equation for binary systems and the Cibulka equation for ternary systems.     

Phase diagram of Na2S2O3 + ethanol + water at ambient pressure and temperature

In the present communication, we report the studies concerning liquid–liquid–solid equilibria for the ternary system sodium thiosulphate (Na₂S₂O₃) + ethanol + water at ambient pressure and at room temperature (303 ± 2 K). The solubility data of Na₂S₂O₃ are reported for solutions in water, ethanol and solutions of varying concentrations of ethanol in water. The phase diagram for the said system is developed, described and compared with similar system K₂CO₃ + methanol + water. These results have been explained in terms of structural properties of aqueous ethanol solutions and further discussed in terms of the effect of ions to cause phase separation.     

Study on the effect of increasing the chain length of the alkanol in excess molar enthalpies of mixtures containing 2-methoxy-2-methylpropane, 1-alkanol,decane

Excess molar enthalpies for the ternary system {x₁ 2-methoxy-2-methylpropane + x₂ ethanol + (1 − x₁ − x₂) decane} and the involved binary mixture {x ethanol + (1 − x) decane} have been measured at the temperature of 298.15 K and atmospheric pressure, over the whole composition range. No experimental excess enthalpy values were found in the currently available literature for the ternary mixture under study. The results were fitted by means of different variable-degree polynomials. Smooth representations of the results are presented and used to construct constant excess molar enthalpy contours on Roozeboom diagrams. The excess molar enthalpies for the binary and ternary system are positive over the whole range of composition. The binary mixture {x ethanol + (1 − x) decane} is asymmetric, with its maximum displace toward a high mole fraction of decane. The ternary contribution is also positive, and the representation is asymmetric.     

Measurement and correlation of vapor–liquid equilibria for methanol + methyl laurate and methanol + methyl myristate systems near critical temperature of methanol

A flow-type method was adopted to measure the vapor–liquid equilibria for methanol + methyl laurate and methanol + methyl myristate systems at 493–543 K, near the critical temperature of methanol (T_c = 512.64 K), and 2.16–8.49 MPa. The effect of temperature and fatty acid methyl esters to the phase behavior was discussed. The mole fractions of methanol in liquid phase are almost the same for both systems. In vapor phase, the mole fractions of methanol are very close to unity at all temperatures. The present vapor–liquid equilibrium data were correlated by PRASOG. A binary parameter was introduced to the combining rule of size parameter. The binary parameters of methanol + fatty acid methyl ester systems were determined by fitting the present experimental data. The correlated results are in good agreement with the experimental data. The vapor–liquid equilibria for methanol + methyl laurate + glycerol and methanol + methyl myristate + glycerol ternary systems were also predicted using the methanol + fatty acid methyl ester binary parameters. The mole fractions of methanol in vapor phase are around unity even if glycerol is included in the systems.     

Volumetric properties of the ternary system ethanol + chloroform + benzene at temperature range (288.15–313.15) K: Experimental data,correlation and prediction by cubic EOS

Densities ρ of the ternary system (ethanol + chloroform + benzene) and binaries (ethanol + chloroform) and (chloroform + benzene), have been measured at six temperatures (288.15, 293.15, 298.15, 303.15, 308.15, 313.15) K and pressure 101.33 kPa with an Anton Paar DMA 5000 digital vibrating tube densimeter. Excess molar volumes V^E were calculated from these densities data and fitted by the polynomial Redlich–Kister (for binary data) and Nagata and Tamura (for ternary data) equations. Radojkovi? et al. equation was used for the prediction of the V^E of ternary data. The obtained results have been explained in terms of different effects between molecules of present species, taking into consideration influence of temperature on them.     

Prediction of vapor-liquid equilibrium data of the system MTBE + methanol + ethanol by PRSV2 EOS

The Stryjek and Vera (1986) [9] modification of Peng-Robinson (PRSV2) equation of state has been applied for modeling vapor-liquid equilibrium of the systems MTBE + methanol, MTBE + ethanol and methanol + ethanol. Binary interaction parameters for mixing rules have been estimated by using experimental data at the atmospheric pressure. The calculated binary interaction parameters were used for predicting azeotropic behavior at high pressure and also for isobaric equilibrium points which showed an excellent agreement with experimental data. In addition, estimated binary interaction parameters for binary systems were used for ternary system (MTBE + methanol + ethanol). The predictions deviated only slightly from the experimental data. The results show PRSV2 can be used for VLE prediction of polar systems.     

Study of the behaviour of the azeotropic mixture ethanol–water with imidazolium-based ionic liquids

In this work, experimental data of isobaric vapour–liquid equilibria for the ternary system ethanol + water + 1-hexyl-3-methylimidazolium chloride ([C₆mim][Cl]) and for the corresponding binary systems containing the ionic liquid (ethanol + [C₆mim][Cl], water + [C₆mim][Cl]) were carried out at 101.300 kPa. VLE experimental data of binary and ternary systems were correlated using the NRTL equation. In a previous work [N. Calvar, B. González, E. Gómez, A. Domínguez, J. Chem. Eng. Data 51 (2006) 2178–2181], the VLE of the ternary system ethanol + water + [C₄mim][Cl] was determined and correlated, so we can study the influence of different ionic liquids in the behaviour of the azeotropic mixture ethanol–water.     

The effect of aqueous organic solvents on the dissociation constants and thermodynamic properties of alkanolamines

The dissociation constants of protonated monoethanolamine and N-methyldiethanolamine have been determined in methanol–water, ethanol–water, and t-butanol–water solvents. The alcohol mole fractions were ranging from 0.2 to 0.95 and the temperatures from 283 to 323 K, 283 to 333 K, and at 298.15 K, respective to the different solvents. The experimental results are reported with the standard state thermodynamic properties. The basic strength of the protonated alkanolamine decreases with decreasing dielectric constant and increasing temperature of the solvent.     

Liquid–liquid equilibria for mixtures containing water,methanol, fatty acid methyl esters,and glycerol

The liquid–liquid equilibrium (LLE) data, including tie-lines and phase boundaries, were measured for the ternary systems of water + methanol + methyl oleate, water + methanol + methyl linoleate, glycerol + methanol + methyl oleate, and glycerol + methanol + methyl linoleate at temperatures from 298.2 K to 318.2 K under atmospheric pressure. All the LLE data follow the Othmer-Tobias equation. Each ternary system behaves type-I LLE. The areas of two-liquid coexistence region decrease with increasing temperature. The experimental data were applied to test the validity of the UNIFAC model and its modified versions, including UNIFAC-LLE and UNIFAC-Dortmund. The LLE data were also correlated with the NRTL and the UNIQUAC models. The UNIQUAC model yielded better results.     

The effect of solvent composition on swelling and shrinking properties of poly(acrylamide-co-itaconic acid) hydrogels

The peculiarities of the equilibrium swelling ratio and swelling-shrinking kinetics of polyelectrolyte copolymeric hydrogels consisting of acrylamide and itaconic acid (AAm/IA) have been studied in water/nonsolvent (acetone, methanol, ethanol and 1-butanol) mixtures as a function of solvent composition and IA content in the hydrogel. The phase transition of these hydrogels was generated by changing the solvent composition by progressive substitution of water by the nonsolvent. For all P(AAm/IA) hydrogels, the form of the shrinking curves was determined to be strongly dependent on the type of the nonsolvent used. The rate of shrinking of these hydrogels increased in the order 1-butanol < ethanol < methanol < acetone.     

Phase behavior of the system hyperbranched polyglycerol + methanol + carbon dioxide

Phase equilibrium data have been measured for the ternary system hyperbranched polyglycerol + methanol + carbon dioxide at temperatures of 313–450 K and pressures up to 13.5 MPa. Phase changes were determined according to a synthetic method using the Cailletet setup. At elevated temperatures the system shows a liquid–liquid–vapor region with lower solution temperatures. Besides the vapor–liquid and liquid–liquid equilibria, the vapor–liquid to vapor–liquid–liquid and vapor–liquid–liquid to liquid–liquid phase boundaries are reported at different polymer molar masses and can serve as test sets for thermodynamic models. A distinct influence of the polymer molar mass on the vapor–liquid equilibrium can be noticed and indicates the existence of structural effects due to the polymer branching. Modeling the systems with the PCP-SAFT equation of state confirms these findings.     

Isothermal vapor–liquid equilibrium at 333.15 K,excess molar volumes and refractive indices at 298.15 K for mixtures of tert-amyl methyl ether + ethanol + 2,2,4-trimethylpentane

Isothermal vapor–liquid equilibrium data at 333.15 K are measured for the binary system tert-amyl methyl ether + ethanol and tert-amyl methyl ether + 2,2,4-trimethylpentane and for ternary system tert-amyl methyl ether + ethanol + 2,2,4-trimethylpentane by using headspace gas chromatography. The experimental vapor–liquid equilibrium data were correlated with G^E models (Margules, van Laar, Wilson, NRTL, UNIQUAC) equations. The excess volume and deviations in molar refractivity data are also reported for the same binary and ternary systems at 298.15 K. These data were correlated with the Redlich–Kister equation for the binary systems and the Cibulka equation for the ternary system, respectively. The experimental ternary excess volume and deviations in molar refractivity data, were also compared with the estimated values from the binary contribution models of Tsao–Smith, Kohler, Rastogi and Radojkovi?.