Chemical stability of La1−xSrxCrO3 in oxidizing atmospheres

The single-phase region of La_1−xSr_xCrO₃ (x=0.1, 0.2, 0.3) was precisely determined as a function of temperature, P_O2 and Sr content. The powders with the nominal composition of La_1−xSr_xCrO₃ were equilibrated under various conditions, and then identified by XRD analyses. To confirm the equilibration, two independent experiments were performed for each composition observing (i) the precipitation of the second phase from a single-phase solid solution, and (ii) the formation of the single phase from the constituent oxides. Two kinds of second phases, SrCrO₄ and an unknown phase, were observed depending on the conditions. The second phases tended to appear at low temperature, in high P_O2 and with a large Sr content. The single-phase regions obtained via the two equilibration routes were in good agreement with each other. The thermodynamic calculations on the supposition of ideality of the solid solution essentially reproduced the experimental results. When this material is used as the interconnects of solid oxide fuel cells, much attention should be paid to its relatively narrow solubility range of Sr; for example, the solubility limit is approximately 0.1 under a typical cathode-side condition (1273 K, air).     

Neutron diffraction study of the crystal structure and structural phase transition of La0.7Ca0.3−xSrxCrO3 (0≤x≤0.3): The relationship between thermodynamic behavior and crystal structure changes at the phase transition

The crystal structure of the La_0.7Ca_0.3−xSr_xCrO₃ series, including the compositional and temperature dependence of the structural parameters, has been studied by variable temperature neutron diffraction measurements. The extent of the distortions from the ideal cubic perovskite structure has been evaluated quantitatively using the average bond lengths and the mean volumes of the [CrO₆] octahedron and [(La/Ca/Sr)O₁₂] polyhedron, and has been shown to decrease with increase of Sr content or temperature. At the structural phase transition from the orthorhombic (Pnma) structure to the rhombohedral one, the volume of the [CrO₆] octahedron decreases whereas that of the [(La/Ca/Sr)O₁₂] polyhedron shows little difference, resulting in an overall decrease in the level of distortion. The change in the degree of distortion at the phase transition decreases with increase of Sr content, in agreement with the smaller variation of the enthalpy and volume for the specimens with higher Sr content.     

Analysis of structural and magnetic phase transition behaviors of La1−xSrxCrO3 by measurement of heat capacity with thermal relaxation technique

The heat capacity, C_p, of the La_1−xSr_xCrO₃ system and its temperature dependence have been measured by a thermal relaxation technique. Both structural and magnetic phase transitions were detected at temperatures that can be surmised from the phase diagram proposed in previous studies. The observed variation in enthalpy after the first-order structural phase transition, ΔH, showed agreement with those measured by differential scanning calorimetry (DSC). A decrease in the variation in C_p in the second-order magnetic phase transition, ΔC_p, with an increase in Sr content was detected, which can be attributed to a decrease in electronic spin configuration entropy with an increase in Sr content. In the dependence of ΔC_p on Sr content, a bending point was also observed at x  0.12, at which the crystal system varies from an orthorhombic-distorted perovskite structure to a rhombohedral-distorted perovskite structure.     

Composition-induced structural phase transitions in the (Ba1−xLax)2In2O5+x (0?x?0.6) system

Composition-induced structural phase changes across the high temperature, fast oxide ion conducting (Ba_1−xLa_x)₂In₂O_5+x, 0?x?0.6, system have been carefully analysed using hard mode infrared (IR) powder absorption spectroscopy, X-ray powder diffraction and electron diffraction. An orthorhombic brownmillerite to three-dimensionally disordered cubic perovskite phase transition in this system is signalled by a drastic change in slope of both wavenumber and average line widths of IR spectra as a function of composition. Some evidence is found for the existence of an intermediate tetragonal phase (previously reported to exist from electron diffraction data) around x∼0.2. The new spectroscopic data have been used to compare microscopic and macroscopic strain parameters arising from variation in composition. The strain and spectroscopic data are consistent with first-order character for the tetragonal→orthorhombic transition, while the cubic→tetragonal transition could be continuous. Differences between the variation with composition of spectral parameters and of macroscopic strain parameters are consistent with a substantial order/disorder component for the transitions. There is also evidence for precursor effects within the cubic structure before symmetry is broken.     

Phase stability of La1−xCaxCrO3−δ in oxidizing atmosphere

The chemical stability of perovskite-type La_1−xCa_xCrO_3−δ (x=0.1, 0.2, 0.3) in high oxygen partial pressure, P_O2, was investigated with three methods: thermogravimetry, XRD analysis, and thermodynamic calculation. The second phase, CaCrO₄ was observed by XRD analysis on the powder equilibrated in high P_O2. Thermogravimetry under fixed temperatures sensitively detected the segregation of the second phase in the form of oxygen incorporation, because oxidation of chromium ion accompanies the segregation. The second phase tended to appear in high P_O2 and at low temperature. The single-phase regions of La_1−xCa_xCrO_3−δ obtained from the two experimental methods well agreed with each other. The results of thermodynamic calculation on the assumption of ideality of the solid solution also agreed with the experimental results. These results suggested the sufficient chemical stability of La_1−xCa_xCrO_3−δ in high P_O2 concerning the application to an interconnector of high-temperature solid oxide fuel cells; for example, La_0.7Ca_0.3CrO_3−δ is stable at 1273 K in air.     

Crystal structure, thermal expansion and conductivity of anisotropic La1−xSrxGa1−2xMg2xO3−y (x=0.05, 0.1) single crystals

Crystal structure and anisotropy of the thermal expansion of single crystals of La_1−xSr_xGa_1−2xMg_2xO_3−y (x=0.05 and 0.1) were measured in the temperature range 300-1270 K. High-resolution X-ray powder diffraction data obtained by synchrotron experiments have been used to determine the crystal structure and thermal expansion. The room temperature structure of the crystal with x=0.05 was found to be orthorhombic (Imma, Z=4, a=7.79423(3) Å, b=5.49896(2) Å, c=5.53806(2) Å), whereas the symmetry of the x=0.1 crystal is monoclinic (I2/a, Z=4, a=7.82129(5) Å, b=5.54361(3) Å, c=5.51654(4) Å, β=90.040(1)°). The conductivity in two orthogonal directions of the crystals has been studied. Both, the conductivity and the structural data indicate three phase transitions in La_0.95Sr_0.05Ga_0.9Mg_0.1O_2.92 at 520-570 K (Imma-I2/a), 770 K (I2/a-R3c) and at 870 K (R3c-R-3c), respectively. Two transitions at 770 K (I2/a-R3c) and in the range 870-970 K (R3c-R-3c) occur in La_0.9Sr_0.1Ga_0.8Mg_0.2O_2.85.     

Evolution of structure and magnetic properties in electron-doped double perovskites, Sr2−xLaxMnWO6 (0?x?1)

Powder neutron and X-ray diffraction studies show that the double perovskites in the region 0?x?1 exhibit two crystallographic modifications at room temperature: monoclinic P2₁/n and tetragonal I4/m, with a boundary at 0.75<x<0.9. Magnetic susceptibility measurements indicate that for x=0 and 0.5 Sr_2−xLa_xMnWO₆ orders antiferromagnetically (AFM) at 15 and 25 K, respectively, for 0.75?x<1.0, a contribution of weak ferromagnetism (FM), probably due to canted-AFM order, increases with increasing x. The end point compound SrLaMnWO₆ shows the strongest FM cluster effect; however, no clear evidence of magnetic order is discernable down to 4.2 K. X-ray absorption spectroscopy (XAS) confirms Mn²⁺ and mixed-valent W^6+/5+ formal oxidation states in Sr_2−xLa_xMnWO₆.     

Thermochemistry of La0.7Sr0.3Mn1−xFexO3 solid solutions (0<x<1)

The structure, the energetics and the internal redox reactions of La_0.7Sr_0.3Fe_xMn_1−xO₃ have been studied in the complete solid solution range 0.0<x<1.0. High temperature oxide melt drop solution calorimetry was performed to determine the enthalpies of formation from binary oxides and the enthalpy of mixing. There is a noticeable change in the energetics of the solid solution near x=0.7, which is due to the growing concentration of Fe⁴⁺ at higher Fe/(Fe+Mn) ratio. The balance between different valences of the transition metals, Mn and Fe, is the main factor in determining the energetics of the La_0.70Sr_0.30Fe_xMn_1−xO₃ solid solution.     

Structure and magnetic order in the series BixRE1−xFe0.5Mn0.5O3 (RE=La,Nd)

The influence of Bi³⁺ on the structural and magnetic properties of the rare-earth-containing perovskites REFe_0.5Mn_0.5O₃ (RE=La,Nd) was studied, and the limit of bismuth substitution was determined to be x≤0.5 in Bi_xRE_1−xFe_0.5Mn_0.5O_3+δ (RE=La,Nd) at ambient pressure. Crystal structures in both La and Nd series were determined to be GdFeO₃-type Pnma with the exception of the Bi_0.3La_0.7Fe_0.5Mn_0.5O₃ sample, which is monoclinic I2/a in the a⁻b⁻b⁻ tilt scheme. The samples undergo a transition to G-type antiferromagnetic order along with a weak ferromagnetic component, mixed with cluster-glass type behavior. The substitution of bismuth into the lattice results in a drop in T_N relative to the lanthanide end-members. Long range ordering temperatures T_N in the range 240-255 K were observed, with a significantly lower ordered magnetic moment in the case of lanthanum (M∼1.7-1.9 μ_B) than in the case of neodymium (M∼2.1 μ_B).     

Effect of the A Cation Size on the Structural, Magnetic, and Electrical Properties of Perovskites (La1−xNdx)0.7Sr0.3r003nMnO3

An intense effort has recently been devoted to studying the interplay between structure, magnetism, and transport in manganese perovskite Ln_1−xA_xMnO₃ (Ln=La, Pr, Nd, Sm; A=Ca, Ba, Sr). As a function of temperature, applied magnetic field, doping, A-site ionic radius 〈r_A〉, and A-site size disorder, this system displays a rich phase diagram for both magnetotransport and structural properties. We have investigated the structural, magnetic, and transport properties of (La_1−xNd_x)_0.7Sr_0.3MnO₃. The crystal structure was examined by X-ray powder diffraction which indicated that all the samples were single phase and revealed a transition from rhombohedral to orthorhombic structure with increasing x. The magnetization and resistivity investigation shows that for all values of x, (La_1−xNd_x)_0.7Sr_0.3MnO₃ are ferromagnetic-metallic at low temperatures and paramagnetic-semiconductor above the Curie temperature T_c.     

Crystal structure and magnetic properties of high-oxygen pressure annealed Sr1−xLaxCo0.5Fe0.5O3−δ (0?x?0.5)

Structural and magnetic studies are presented for the perovskite type Sr_1−xLa_xCo_0.5Fe_0.5O_3−δ (0?x?0.5) materials annealed under moderately high-oxygen pressures of ∼200 atm. A detailed analysis of the room temperature neutron time-of-flight diffraction data reveals that the crystal structure of the sample SrCo_0.5Fe_0.5O_2.89(1), previously described as vacancy-disordered cubic, is similar to the formerly reported, oxygen-vacancy ordered Sr₈Fe₈O₂₃ compound, i.e. Sr₈Co₄Fe₄O₂₃ is tetragonal with the I4/mmm symmetry. With an increase of the La content the studied materials become nearly oxygen stoichiometric and a lowering of the crystal symmetry is observed from cubic (x=0.1 and 0.2) to tetragonal I4/mcm (x=0.3 and 0.4), and finally to monoclinic I12/c1 (x=0.5). Low-temperature structural and magnetic measurements show a ferromagnetic ordering with the maximum Curie temperature near 290 K at x=0.2.     

Solid solubility and phase transitions in the system LaNb1−xTaxo4

The solid solubility between LaNbO₄ and LaTaO₄ was investigated by X-ray diffraction, and a two-phase region was observed in the composition region LaNb_1−xTa_xO₄ where 0.4?x?0.8. Single-phase LaNb_1−xTa_xO₄ (0?x?0.4) with the monoclinic Fergusonite structure at ambient temperature, was observed to transform to a tetragonal Scheelite structure by in-situ high-temperature X-ray diffraction, and the phase transition temperature was shown to increase with increasing Ta-content. This ferroelastic to paraelastic second-order phase transition was described by Landau theory using spontaneous strain as an order parameter. The thermal expansion of LaNb_1−xTa_xO₄ (0?x0.4) was shown to be significantly higher below the phase transition than above. Single-phase LaNb_1−xTa_xO₄ (0.8?x?1) with another monoclinic crystal structure at ambient temperature was shown to transform to an orthorhombic crystal structure by X-ray diffraction and differential scanning calorimetry. The phase transition temperature was observed to decrease with decreasing Ta-content. Finally, orthorhombic LaTaO₄ could also be transformed to monoclinic LaTaO₄ at ambient temperature by applying a uniaxial pressure of 150-170 MPa, reflecting the lower molar volume of monoclinic LaTaO₄.     

CeAlO3 and Ce1−xRxAlO3 (R=La, Nd) solid solutions: Crystal structure, thermal expansion and phase transitions

The crystal structures of CeAlO₃ and the solid solutions Ce_1−xR_xAlO₃ (R=La, Nd), and their thermal behaviour in a wide temperature range of 12−1200 K have been precisely determined by means of in situ high-resolution X-ray powder diffraction technique applying synchrotron radiation, thermal analysis and magnetic measurements. The unique sequence of the reversible phase transitions I4/mcm↔Imma↔R3¯c↔Pm3¯m has been detected in CeAlO₃ and solid solutions formed in the pseudo-binary system CeAlO₃-LaAlO₃. In the Ce_1−xNd_xAlO₃ system, the samples with x=0.3 and 0.5 compositions undergo three phase transformations I2/m↔Imma↔R3¯c↔Pm3¯m, whereas for the Ce-rich sample Ce_0.9Nd_0.1AlO₃ four successive transitions are observed: I4/mcm↔I2/m↔Imma↔R3¯c↔Pm3¯m. Crystal structure parameters of all structural polymorphs of CeAlO₃ and solid solutions based on them as well as their thermal evolution are reported. Based on in situ powder diffraction and DTA/DSC data, the phase diagrams of the pseudo-binary systems CeAlO₃-LaAlO₃ and CeAlO₃-NdAlO₃ are constructed together with a combined phase diagram, where the transition temperatures are presented as a function of the average radius of rare-earth cations.     

Structure and conductivity of strontium-doped cerium orthovanadates Ce1−xSrxVO4 (0≤x≤0.175)

A-site substituted cerium orthovanadates, Ce_1−xSr_xVO₄, were synthesised by solid-state reactions. It was found that the solid solution limit in Ce_1−xSr_xVO₄ is at x=0.175. The crystal structure was analysed by X-ray diffraction and it exhibits a tetragonal zircon structure of space group I4₁/amd (1 4 1) with a=7.3670 (3) and c=6.4894 (1) Å for Ce_0.825Sr_0.175VO₄. The UV-vis absorption spectra indicated that the compounds have band gaps at room temperature in the range 4.5-4.6 eV. Conductivity measurements were performed for the first time up to the strontium solid solution limit in air and in dry 5% H₂/Ar with conductivity values at 600 °C ranging from 0.3 to 30 mS cm⁻¹ in air to 30-45 mS cm⁻¹ in reduced atmosphere. Sample Ce_0.825Sr_0.175VO₄ is redox stable at a temperature below 600 °C although the conductivity is not high enough to be used as an electrode for solid oxide fuel cells.     

Room temperature photoluminescence of amorphous BaxSr1−xTiO3 doped with chromium

ABO₃ amorphous materials, such as BaTiO₃ (BT), SrTiO₃ (ST), PbTiO₃ (PT), and Ba_xSr_1−xTiO₃ (BST) have recently attracted a good deal of attention due to their ferroelectric and electro-optical properties. Intense photoluminescence at room temperature was observed in amorphous titanate doped with chromium (Ba_xSr_1−xTi_1−yCr_yO₃) prepared by the polymeric precursor method. Results indicated that substantial luminescence at room temperature was achieved with the addition of small Cr contents to amorphous Ba_xSr_1−xTi_1−yCr_yO₃. Further addition of Cr or crystallization were deleterious to the intensity of the luminescent peak obtained for excitation using λ=488.0 nm.     

Synthesis, crystal structure, and density of (W1−xAlx)C

A new solid solution system of Al in WC, with the stoichiometry of (W_1−xAl_x)C (x=0.10, 0.25, 0.50, 0.75, 0.86), has been synthesized by a solid-state reaction between W_1−xAl_x alloys and carbon at around 1673 K in vacuum. Environment scanning electron microscope, energy-dispersive analysis of X-ray, X-ray photoelectron spectroscopy, and inductively coupled plasma analyses are used to certify the formation of the products. The mechanism of the solid-state reaction is also discussed. (W_1−xAl_x)C is identified to crystallize in the hexagonal space group P6m2 (No. 187) and belongs to the WC structure type. The atoms of W and Al occupy the same lattice site (1a site) in the cell of (W_1−xAl_x)C. The cell parameters for each specimen in the phase of W-Al-C are quite close to that of WC, while their densities are far lower than that of WC.     

Effects of gold catalysts and thermal evaporation method modifications on the growth process of Zn1−xMgxO nanowires

In this paper, we investigate the roles of gold catalysts and thermal evaporation method modifications in the growth process of Zn_1−xMg_xO nanowires. Zn_1−xMg_xO nanowires are fabricated on silicon substrates with and without using a gold catalyst. Characterizations reveal that Mg acts in a self-catalyst role during the growth process of Zn_1−xMg_xO nanowires grown on catalyst-free substrate. The optical properties and crystalline quality of the Zn_1−xMg_xO nanowires are characterized by room temperature photoluminescence (PL) measurements and Raman spectroscopy, respectively. The Raman and PL studies demonstrate that the Zn_1−xMg_xO nanowires grown using the catalyst-free method have good crystallinity with excellent optical properties and have a larger band-gap in comparison to those grown with the assistance of gold.     

High temperature phase transition in SOFC anodes based on Sr2MgMoO6−δ

The double perovskite Sr₂MgMoO_6−δ has been recently reported as an efficient anode material for solid oxide fuel cells (SOFCs). In the present work, this material have been investigated by high temperature X-ray diffraction (XRD), differential scanning calorimetry (DSC) and impedance spectroscopy to further characterise its properties as SOFC anode. DSC and XRD measurements indicate that Sr₂MgMoO_6−δ exhibits a reversible phase transition around 275 °C from triclinic () with an octahedral tilting distortion to cubic () without octahedral distortion. This phase transition is continuous with increasing temperature without any sudden cell volume change during the phase transformation. The main effect of the phase transformation is observed in the electrical conductivity with a change in the activation energy at low temperature. La³⁺ and Fe-substituted Sr₂MgMoO_6−δ phases were also investigated, however these materials are unstable under oxidising conditions due to phase segregations above 600 °C.     

Structure distortion and magnetism in double perovskites Ca2−xLaxFeReO6 (0≤x≤0.8)

The crystal structure and magnetism of Ca_2−xLa_xFeReO₆ (0≤x≤0.8) double perovskites have been investigated. The samples with low doping (x≤0.4) are found to crystallize with the monoclinic P2₁/n superstructure, while those in the high doping ones (x≥0.6) have orthorhombic Pbnm superstructure. With the increase of an La doping, the anti-site defects increases, giving rise to highly disordered samples at the Fe and Re positions. At the low doping region (x≤0.4), the compounds undergo a simultaneous structural and magnetic transition accompanying a slight increase of the Curie temperature. The increase of Curie temperature is discussed in terms of the structural change with doping.     

Comparative XANES study on the two electron-doped high-Tc superconductor systems, (Sr,La)CuO2 and (Nd,Ce)2CuO4

Here we employ high-quality samples of (Sr_1−xLa_x)CuO₂ and (Nd_2−xCe_x)CuO₄ and XANES spectroscopy at O-K, Cu-L_2,3 and Ce-M_4,5 edges to gain comprehensive understanding of the electronic structure and doping in n-type high-T_c superconductors. Not only common but also slightly different features are revealed for the two systems. From O-K-edge spectra, the UHB is found essentially independent of the electron-doping level for both the systems, in line with our understanding that the doped electrons do not go to the O site in n-type copper-oxide superconductors. Another common observation is that the main Cu^II peak at the Cu-L₃ edge (due to transitions to the Cu^II-3d orbitals) systematically decreases in intensity upon electron doping, hence verifying the fact that the doped electrons go to the Cu site. The difference then between the two systems is that in (Sr_1−xLa_x)CuO₂ the weaker Cu^II peak due to transitions to the Cu^II-4s orbital depends on the degree of doping. Moreover, it was found that with increasing x, electron density increases much faster in (Sr_1−xLa_x)CuO₂ than in (Nd_2−xCe_x)CuO₄. This is a consequence of two phenomena: a tiny increase in oxygen content concomitant to the Ce^IV-for-Nd^III substitution and the somewhat lower Ce-valence value of +3.8 compared to the nominal tetravalent state.