侧基差异对含磷、氟、氧和硅烷聚合物构象性质的影响

基于改进的旋转异构态模型和生成矩阵统计方法,推导了均方回转半径和均方偶极矩的公式,并应用于研究无机和半无机聚合物构象-构型依赖的性质.计算结果发现,聚合物链的柔性和极性与含杂元素成分、侧基的大小、构象能及链规整程度有关,不对称链比对称链极性更强.聚甲基苯基硅烷(PMPS)和聚二甲基亚硅烷(PDMS)与聚甲基苯基硅醚、聚苯基硅烷和聚磷酸等相比,因侧基高密集分布导致链尺寸较大.尤其是PMPS,其长链在考虑侧基与不考虑侧基影响下计算的链尺寸差异为4. 68%,特性黏数随构型参数和链聚合度增大有较大的变化.同样,PDMS的温度系数随链聚合度增大有独特的变化规律.因此,建议在计算分子链尺寸和极性时,不能忽略侧基的大小、分布和极性.     

聚硅氧烷侧基极性对链均方偶极矩的影响

为了改进无机高分子链偶极矩的计算,在旋转异构态模型和生成矩阵统计方法基础上,导出了可以同时考虑骨架键和侧基极性的均方偶极矩公式,应用于对称和不对称聚硅氧烷高分子链的偶极矩构象构型统计性质的分析,及聚二甲基硅氧烷(PDMS)链、聚甲基苯基硅氧烷(PMPS)链是否考虑侧基极性的偶极矩比较。计算结果表明,PDMS的偶极矩特征比值0.36与实验结果一致,它大于忽略侧基极矩的特征比值约46%,均方偶极矩温度系数为1.29×10-3K-1,无规聚甲基苯基硅氧烷链(50%i-PMPS)的均方偶极矩特征比和温度系数分别为0.61和1.73×10-3K-1.不考虑侧基极性的均方偶极矩特征比与PDMS不考虑侧基时趋于同样的值0.20.对PMPS偶极矩与链规整性关系研究发现,PMPS间同链的均方偶极矩要大于全同和无规链,而全同链温度系数最大.均方偶极矩对一级相互作用能的依赖程度依次按间同链、无规和全同链顺序增加,而间同和全同链均方偶极矩受二级相互作用能的影响要大于无规链.     

三级相互作用对聚亚甲基链末端距四次矩的影响

本文用三级相互作用近似理论导出了高分子链末端距的四次矩的计算公式。计算聚亚甲基链的末端距四次矩,并同二级相互作用的结果进行了比较。对于聚亚甲基链,三级相互作用近似的四次矩小于二级相互作用近似的四次矩。     

聚亚甲基绿的性质

在 10～ 6 0℃范围内 ,测定了聚亚甲基绿的循环伏安图和交流阻抗图 ,测定了循环伏安所用电解质溶液的电导率随温度的变化 .在不同温度下 ,聚亚甲基绿的循环伏安图上均有一阳极峰和一阴极峰 ,阳极峰和阴极峰的峰电流均随温度升高而增加 ,即电极反应速率随温度升高而增加 .交流阻抗的结果表明 ,聚亚甲基绿的电荷传递电阻Rct随温度升高而增大 .热重 (TG)实验表明聚亚甲基绿热失重是分三步进行的 ,聚合物在 2 6 3 .1℃时发生分解 .扫描电镜 (SEM)结果显示聚亚甲基绿表面呈颗粒状     

含亚甲基链段苯并二(口恶)唑类聚合物的合成、表征及性能

通过溶液缩聚的方法合成了一系列含有不同长度亚甲基链段的聚苯并羟基酰胺(PHACx),然后在200～300 ℃下环化脱水制备了相应的聚多亚甲基苯并二唑(PBOCx),并对其结构进行了表征,探讨了聚合物的溶解性、热性能和光物理性能.研究表明:在主链上引入亚甲基提高了苯并二唑类聚合物在有机溶剂中的溶解性,其中PBOC3 和PBOC4具有较好的溶解性能,但随着亚甲基数量的进一步增加,溶解性有下降趋势.此外,所有的PBOCx聚合物均表现出良好的耐热性,在空气中的热分解温度可达到450 ℃以上.对聚合物光物理性能的初步研究表明:随着柔性链段的增加,电子共轭作用逐渐减弱,紫外吸收发生了蓝移.     

环形聚苯乙烯的稀溶液性质——Ⅱ. 第二维利系数

第二维利系数(A_2)是表征高分子链段间和高分子溶剂分子间相互作用的参数。对于环形高分子的第二维利系数,最早Casassa曾做过计算。利用“双接触”模型,Casassa计算了环形高分子的第二维利系数(A_(2r))为A_(2r)=(N_αβN~2/2M~2)[1-C_z O(z~2)]式中M为聚合物的分子量,N_α为Avogadro常数,N为高分子链段数,β为表征链段对排斥体积的二元集团积分,Z为排斥体积参数。式中系数C对环形或线形分子数值不同。     

含亚甲基链段苯并二嗯唑类聚合物的合成、表征及性能

通过溶液缩聚的方法合成了一系列含有不同长度亚甲基链段的聚苯并羟基酰胺（PHACx），然后在200～300℃下环化脱水制备了相应的聚多亚甲基苯并二嘿唑（PBOCx），并对其结构进行了表征，探讨了聚合物的溶解性、热性能和光物理性能。研究表明：在主链上引入亚甲基提高了苯并二嘿唑类聚合物在有机溶剂中的溶解性，其中PBOC3和PBOC4具有较好的溶解性能，但随着亚甲基数量的进一步增加，溶解性有下降趋势。此外，所有的PBOCx聚合物均表现出良好的耐热性，在空气中的热分解温度可达到450℃以上。对聚合物光物理性能的初步研究表明：随着柔性链段的增加，电子共轭作用逐渐减弱，紫外吸收发生了蓝移。     

含聚二甲基硅氧烷短支链的聚酰亚胺的合成及其透氧性的研究

介绍了在甲撑二苯胺的亚甲基上接上聚二甲基硅氧烷短链，并用含二甲基硅氧烷短链的二苯胺单体和均苯四甲酸二酐反应制取聚酰亚胺的方法。实验结果表明，在含三硅量相同的情况下，支链型的改性聚酰亚胺的机械强度高。氧的透过系数随支链长度的增加而增加，当二甲基硅氧烷短链的硅原子由１增加到４时，透氧系数由３．６５Ｂａｒｒｅ增加到１２．０Ｂａｒｒｅ，而Ｏ２／Ｎ２分离系数则由６．４降到３．５。     

微相分离及链结构对聚酯-聚醚嵌段共聚物分子运动的影响

本文首先研究了成型方法和热处理对聚对苯二甲酸乙二酯与聚氧四亚甲基嵌段共聚物动态力学温度谱的影响,结合应力-应变曲线讨论了微相分离与力学性能的关系。其次,比较了三种不同链结构的聚酯-聚醚嵌段共聚物在不同温控程序下的动态力学温度谱,讨论了链结构对软链段结晶的影响。最后观察了聚氨酯-聚醚嵌段共聚物双重玻璃化转变现象并作了解释。     

叶立德活性聚合制备基于聚亚甲基的大分子单体

利用叶立德活性聚合方法制备了两种基于聚亚甲基的大分子单体. 其中一种是以叶立德活性聚合制备的主链链端含有羟基的聚亚甲基(PM-OH)为原料, 通过链端羟基的基团转换, 得到链端含有甲基丙烯酸酯基的大分子单体. 另一种则是以硼烷-四氢呋喃(BH₃-THF)和二乙烯基苯反应得到的三烷基硼中间体为催化剂和引发剂, 然后进行叶立德活性聚合, 再经过二水合氧化三甲胺(TAO)的氧化, 最终得到基于聚亚甲基的一端含有羟基另一端含有苯乙烯基的大分子单体. 通过高温核磁氢谱、傅立叶红外光谱和高温凝胶色谱法表征了这两种大分子单体的链结构和分子量及其分布.     

长棒状T形三组分双亲分子相行为的耗散粒子动力学模拟

采用耗散粒子动力学方法建立了以侧链长度和温度为变量的相图,计算了相关结构参数及每个液晶相对应侧链的有效体积分数,重现了实验上观察到的五边形、六边形柱状相及刚棒在层内位置的有序堆垛层状结构.研究发现,长棒状T形三组分双亲分子相图中的相序列和相结构符合相关报道,并且侧链有效体积分数f L与实验值一致.表明粗粒化模型反映了真实T形分子的主要特性,如分子的拓扑结构、排除体积效应及分相趋势、刚棒液晶基元的长径比和侧链的空间效应.证实了侧链尺寸对主/侧链非线性连接体系的自组装结构及各组成单元的位置分布的重要作用.     

Response of the mean-square optical anistropy of chain molecules to the imposition of excluded volume

The influence of the chain expansion produced by excluded volume on the mean-square optical anisotropy has been studied in six types of polymers. The mean-square optical anistropy for a specified configuration is calculated using the valence optical scheme. Realistic rotational isomeric state models are used for the configurational statistics of the unperturbed chains. Excluded volume is introduced by hard sphere interactions. Results obtained with chains of 100, 200, 300, and 400 bonds permit extrapolation to the behavior expected for much longer chains. The mean-square optical anisotropy of polyethylene is insensitive to excluded volume. A similar conclusion was obtained several years ago in a study of chains confined to a tetrahedral lattice and weighted in a manner appropriate for the short-range interactions in polyethylene.² Different behavior is seen in poly(vinyl chloride), poly(vinyl bromide), polystyrene, poly(p-chlorostyrene), and poly(p-bromostyrene). The mean-square optical anisotropy of these five vinyl polymers is sensitive to the imposition of excluded volume if the stereochemical composition is exclusively racemic. Much smaller effects are seen in meso chains and in chains with Bernoullian statistics and an equal probability for meso and racemic dyads.     

Molecular dimensions of polypeptides in helicogenic solvents

The dependence of the molecular dimension of polypeptides in helicogenic solvents on molecular weight was calculated by using the Zimm-Bragg-Nagai theory in collaboration with the broken-rod model, in which the excluded volume effect was taken into account by setting the equivalent chain to be a nonintersecting chain. Our calculated results for PBLG in helicogenic solvents were compared with experiment with good agreement. The flexibility of the helices of PCBL and PELG as broken rods corresponded to that of PBLG without excluded volume effect (i.e., the broken rod of a self-intersecting chain) in a comparison of their experimental data with our calculated results for PBLG of self-intersecting and nonintersecting chains. Over a wide range of molecular weights M our theory explains the dependence of the length per monomeric residue h on M, even for short chains in which h > 1.5 Å.     

拉力诱导下的紧密高分子链相变行为

采用相互作用自回避行走(interacting self-avoiding walks,ISAWS)模型研究了一端固定的紧密高分子链在拉伸过程中的低温相变行为,观察到在拉伸过程中当温度T<0.1时平均拉力会出现一个震荡,随着温度的升高这种震荡现象又渐渐消失,这是由于紧密高分子链在低温时类似于β折叠的"冻结构象"被拉开而引起的.比较吸附条件下和无吸附作用下平均拉力、自由能以及相变行为的差别,发现在吸附条件下在拉伸的初始阶段为了克服表面吸附的相互作用,拉力会出现一个峰.吸附作用也使得外界作用到高分子链上的实际有效拉力减小,造成崩塌相态(collapsed phase)区域面积减少.另外发现在吸附条件下平均拉力还受温度变化的影响.在拉伸的初期由于单体间存在体积排除效应,平均拉力是随着温度的升高而降低,随着拉伸的深入当末端距到达一定长度时平均拉力是随着温度的升高而增加.并同Kumar等人在不考虑吸附作用下拉伸紧密高分子链得到的结果进行了比较.这些研究对于进一步研究外力诱导下吸附紧密高分子的相变有一定的参考价值.     

Monte carlo simulation of polymers in steady potential flows

This work presents a study of the configurational properties of bead-spring chains in steady-state potential flows. These properties are obtained from off-lattice Monte Carlo simulations. The results of our simulations compare favourably with theoretical results for phantom chains. We investigate the effects of excluded volume and hydrodynamic interaction on the configurations of the chains, and compare our results to the predictions of scaling arguments. The scaling law observed here for the latter case deviates from theoretical predictions but is in agreement with findings reported from molecular dynamics simulations.     

Microphase separation in two-dimensional athermal polymer solutions on a triangular lattice

The results of Monte Carlo simulations of 2D polymer solutions are presented. The simulations were performed under athermal conditions for long chains (up to 1024 beads) over a full range of polymer concentration phi, explicitly taking into account the solvent molecules. The results obtained for short chains (N < or = 256) are in good agreement with previous simulations whereas for long chains microphase separation is observed below phi = 0.6. This phenomenon is attributed to strong excluded volume interactions in 2D systems. A sort of interpenetration of the coils is also observed.     

The Structure of Star-Branched Chains in a Confined Space

Summary. We studied the properties of a simplified model of star-branched polymers confined in a slit formed by two parallel and impenetrable surfaces. The chains were built of identical united atoms (segments) whose positions were restricted to vertices of a simple cubic lattice. The polymer excluded volume and polymer segment-surface contact interactions were also introduced into the model. The properties of the model chains were determined by means of Monte Carlo simulations with a Metropolis-type sampling algorithm based on local changes of chain’s conformation. The structure of star-branched chains was investigated and the influence of the confinement and the temperature on the chain dimensions and structure was studied. It was shown that for chains in the adsorbing slits their sizes do not exhibit a universal behavior contrary to confined athermal polymers. The polymers in narrow slits at higher temperatures still exhibited features of a three-dimensional chain. It was also shown that chains in small slits and at low temperatures were fully adsorbed at one of the surfaces but could also switch the surface rapidly.     

The behavior of the structure function at large wavevectors for polymers in different regimes

Off‐lattice Monte Carlo simulations employing the pivot algorithm are used to generate ideal and excluded volume linear polymers in three dimensions. The structure function at large wavevectors is calculated from the resulting configurations. This is compared to the exact equation for ideal chains and to experimental data and both scaling and renormalization group predictions for excluded volume chains. It is found that using the des Cloizeaux form for the distance distribution function in an analytic calculation of the structure function leads to close agreement with the experimental and Monte Carlo data.     

Universal consequences of the presence of excluded volume interactions in dilute polymer solutions undergoing shear flow

The role of solvent quality in determining the universal material properties of dilute polymer solutions undergoing steady simple shear flow is examined. A bead-spring chain representation of the polymer molecule is used, and the influence of solvent molecules on polymer conformations is modelled by a narrow Gaussian excluded volume potential that acts pairwise between the beads of the chain. Brownian dynamics simulations data, acquired for chains of finite length, and extrapolated to the limit of infinite chain length, are shown to be model independent. This feature of the narrow Gaussian potential, which leads to results identical to a delta-function repulsive potential, enables the prediction of both universal crossover scaling functions and asymptotic behavior in the excluded volume limit. Universal viscometric functions, obtained by this procedure, are found to exhibit increased shear thinning with increasing solvent quality. In the excluded volume limit, they are found to obey power law scaling with the characteristic shear rate beta, in close agreement with previously obtained renormalization group results. The presence of excluded volume interactions is also shown to lead to a weakening of the alignment of the polymer chain with the flow direction.     

The behavior of the form factor in two dimensions for linear polymers in different regimes

Off-lattice Monte Carlo simulations employing the PIVOT algorithm are used to generate ideal and excluded volume linear polymers in two dimensions. The form factor at small and large wave vectors is calculated from the resulting configurations and compared to the exact equation for ideal chains and to both scaling and renormalization group predictions for excluded volume chains. It is found that using the des Cloizeaux form for the distance distribution function in an analytic calculation of the form factor leads to close agreement with the Monte Carlo data and that simple expressions for both the small and large wave vector expansions reproduce the essential features of the form factor.