Electrical resistance measurements under pressure on NbTe2 single crystal

Transition metal dichalcogenides, because of their layered structure, are well suited for extreme pressure lubrication. These materials being semiconducting and of layered structure may undergo structural and electronic transitions under pressure. Here we report the details of the preparation and characterization of single crystals of NbTe₂ and the results of electrical resistance measurements under pressure carried out on it to investigate this possibility. Single crystals were grown by the chemical vapor transport technique, using iodine as a transporting agent. The composition of the grown crystals was confirmed on the basis of Energy Dispersive Analysis by X-ray (EDAX) and remaining structural characterization was also accomplished by X-ray Diffraction (XRD) studies. Electrical resistance was measured employing a Bridgman anvil set up to 10?GPa and diamond anvil cell (DAC) assembly up to 25?GPa. A technique slightly modified from that described in the literature for carrying out electrical resistivity measurements in the diamond anvil cell (DAC) under pressure has been standardized.     

Surface morphology of PrBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7-δ</Subscript> single crystals after the long-lasting high-temperature reduction

The results of the detailed scanning electron microscopy study of PrBa₂Cu₃O_7-δ single crystals after the long-lasting high-temperature post-growth treatment are reported. The presence of the unstable decomposition products on the crystal surface indicates that the onset of superconductivity must be related to the structural transformations in the bulk (approximately 20% of the total volume of the examined crystals). The time-dependent character of the superconductivity in the Pr-123 crystals could be attributed to the migration of defects in the Pr−Ba sublattice from the bulk toward the surface.     

Anomalous absorption in H<Subscript>2</Subscript>CN and CH<Subscript>2</Subscript>CN molecules

Structures of H₂CN and CH₂CN molecules are similar to that of H₂CO molecule. The H₂CO has shown anomalous absorption for its transition 1₁₁–1₁₀ at 4.8 GHz in a number of cool molecular clouds. Though the molecules H₂CN and CH₂CN have been identified in TMC-1 and Sgr B2 through some transitions in ortho as well as in para species, here we have investigated the condition under which transitions 1₁₁–1₁₀ and 2₁₂–2₁₁ of these molecules may show anomalous absorption. For the present investigation, we have calculated energy levels and radiative transition probabilities. However, we have used scaled values for collisional rate coefficients. We found that relative values of collisional rate coefficients can produce the required anom-alous absorption in 1₁₁–1₁₀ and 2₁₂–2₁₁ transitions in the molecules.      

Influence of the sample orientation in Sn<Subscript>2</Subscript>P<Subscript>2</Subscript>S<Subscript>6</Subscript> crystals on the hydrostatic piezoelectric coefficients

The influence of the sample orientation on the effective value of the hydrostatic piezoelectric coefficients d _h ⁽ⁱ⁾ of Sn₂P₂S₆ crystals has been studied. The hydrostatic piezoelectric coefficients d _h ⁽¹⁾ and d′ _h ⁽³⁾ , were measured, d _h ⁽¹⁾ =(244±3) pC/N and d′ _h ⁽³⁾ =(92±1) pC/N. The hydrostatic piezoelectric coefficient d _h ⁽³⁾ for orthogonal axis system was calculated to be d _h ⁽³⁾ =(87±2) pC/N. The, optimal orientation of the sample has been found as (Xy l)−20°-cut. Maximal value of the effective hydrostatic piezoelectric coefficient d _h ⁽¹⁾ equals 260 pC/N. Double rotated samples were also studied. The orientation of the samples insensitive to the pressure has been found. The theoretical mean value of hydrostatic piezoelectric coefficient (d _h ) _mean corresponding to randomly oriented Sn₂P₂S₆ grains in a poled composite has been calculated to be (d _h ) _mean =136 pC/N.     

Preparation of TiO<Subscript>2</Subscript>-coated LiCo<Subscript>1/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by electrostatic self-assembly method and its properties

A precursor of TiO₂–LiCo_1/3Ni_1/3Mn_1/3O₂ was prepared by electrostatic self-assembly method. The final product was obtained by heating the precursor at 400–450 °C for 4–6 h in air. X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical tests were used to examine the structural, morphology, elementary valence, and electrochemical characteristics. XRD indicated that the TiO₂-coated material can be indexed by α-NaFeO₂ layered structure, which belongs to hexagonal-type space group R3m. XPS results confirmed the existence of TiO₂ compound on the surface of the coated sample. The SEM image showed that the material had spherically porous morphology with the uniform size about 6 μm. The initial charge–discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ material was 168.8/160.0 mAh/g. After 60 cycles, the discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ sample was 147.0 mAh/g, and the coulombic efficiency was 94.0%. Compared with the uncoated sample, the electrochemical performance of TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ was improved.     

Study of structural phase transitions in YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>6+δ</Subscript> by x-ray photoelectron spectroscopy

We have used x-ray photoelectron spectroscopy to investigate the charge state of oxygen found in the basal structural plane of YBa₂Cu₃O₆+γ.. We have observed a change in this state after thermal treatment, with a transition to the adjacent structural phase region. We have shown that changes in the charge state of oxygen can be used as an indicator of structural changes occurring in YBa₂Cu₃O₆+δ.. We have found that the rate of structural relaxation yttrium barium cuprate depends on the amount of structural water it contains. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 2, pp. 195–198, March–April, 2007.     

One-step synthesis of colloidal Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> and γ-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles at room temperature

A facile room-temperature synthesis has been developed to prepare colloidal Mn₃O₄ and γ-Fe₂O₃ nanoparticles (5 to 25 nm) by an ultrasonic-assisted method in the absence of any additional nucleation and surfactant. The morphology of the as-prepared samples was observed by transmission electron microscopy. High-resolution transmission electron microscopy observations revealed that the as-synthesized nanoparticles were single crystals. The magnetic properties of the samples were investigated with a superconducting quantum interference device magnetometer. The possible formation process has been proposed.     

First-principles calculations on implanted TiO<Subscript>2</Subscript> by 3d transition metal ions

3d transition metal (V, Cr and Fe) ions are implanted into TiO₂ by the method of metal ion implantation. The electronic band structures of TiO₂ films doped 3d transition metal ions have been analyzed by ab initio band calculations based on a self-consistent full-potential linearized augmented plane-wave method within the first-principle formalism. Influence of implantation on TiO₂ films is examined by the method of UV-visible spectrometry. The results of experiment and calculation show that the optical band gap of TiO₂ films is narrowed by ion implantation. The calculation shows that the 3d state of V, Cr and Fe ions plays a significant role in red shift of UV-Vis absorbance spectrum.     

Synthesis of ZnAl<Subscript>2</Subscript>O<Subscript>4</Subscript>/α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> complex substrates and growth of GaN films

With the solid phase reaction between pulsed-laser-deposited (PLD) ZnO film and α-Al₂O₃ substrate, ZnAl₂O₄/α-Al₂O₃ complex substrates were synthesized. X-ray diffraction (XRD) spectra show that as the reaction proceeds, ZnAl₂O₄ changes from the initial (111)-oriented single crystal to poly-crystal, and then to inadequate (111) orientation. Corresponding scanning electron microscope (SEM) images indicate that the surface morphology of ZnAl₂O₄ transforms from uniform islands to stick structures, and then to bulgy-line structures. In addition, XRD spectra present that ZnAl₂O₄ prepared at low temperature is unstable at the environment of higher temperature. On the as-obtained ZnAl₂O₄/α-Al₂O₃ substrates, GaN films were grown without any nitride buffer using light-radiation heating low-pressure MOCVD (LRH-LP-MOCVD). XRD spectra indicate that GaN film on this kind of complex substrate changes fromc-axis single crystal to poly-crystal as ZnAl₂O₄ layer is thickened. For the single crystal GaN, its full width at half maximum (FWHM) of X-ray rocking curve is 0.4°. Results indicate that islands on thin ZnAl₂O₄ layer can promote nucleation at initial stage of GaN growth, which leads to the (0001)-oriented GaN film.     

Structural relaxation of Zr<Subscript>41</Subscript>Ti<Subscript>14</Subscript>Cu<Subscript>12.5</Subscript>Ni<Subscript>10</Subscript>Be<Subscript>22.5</Subscript> bulk metallic glass under high pressure

Zr₄₁Ti₁₄Cu_12.5Ni₁₀Be_22.5 bulk metallic glass (BMG) is annealed at 573 K under 3 GPa and its structural relaxation is investigated by X-ray diffraction, ultrasonic study, compression as well as sliding wear measurements. It is found that after the ZrTiCuNiBe BMG sample was annealed under high pressure, the mechanical properties were improved. Moreover, theBMG with relaxed structure exhibits markedly different acoustic properties. These results are attributed to the fact that relaxation under high-pressure results in a microstructural transformation in the BMG.     

Accuracy in determination of the temperature and partial pressure of CO<Subscript>2</Subscript> in CO<Subscript>2</Subscript>:N<Subscript>2</Subscript>:H<Subscript>2</Subscript>O:NO<Subscript>2</Subscript> mixtures by multiple-frequency laser probing

We present the results of analysis of the errors introduced by hot-band transitions 11¹0-01¹1, 03¹0-01¹1, 12⁰0-12⁰1 of the CO₂ molecule and the absorption lines of the H₂O and NO₂ molecules in determination of the temperature and partial pressure of CO₂, included in the gas mixture CO₂: N₂:H₂O: NO₂ at atmospheric pressure, by multiple-frequency laser probing using a CO₂ laser tunable over the lines of the 00⁰1-[10⁰0,02⁰0]_I,II ground-state laser transitions. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 6, pp. 810–815, November–December, 2007.     

Tunable optical parametric oscillator based on a KTP crystal,pumped by a pulsed Ti<Superscript>3+</Superscript>:Al<Subscript>2</Subscript>O<Subscript>3</Subscript> laser

We present the characteristics of an optical parametric oscillator based on a KTP crystal, pumped with noncritical phase matching by a pulsed Ti³⁺:Al₂O₃ laser, tunable in the range 677–970 nm. Tunable generation of signal and idler waves is obtained in the ranges 1030–1390 nm and 2690–3050 nm respectively. The efficiency of conversion of the pump to the signal wave is ≈23%, which for pulses of duration ≈8 nsec ensures an energy in the range 1.0–11.5 mJ. The width of the emission spectrum for the signal wave is within the range 0.8–1.8 nm and is predominantly determined by the linewidth of the Ti³⁺:Al₂O₃ pump laser. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 3, pp. 351–356, May–June, 2007.     

Phase transition in Pd<Subscript>40</Subscript>Ni<Subscript>10</Subscript>Cu<Subscript>30</Subscript>P<Subscript>20</Subscript> bulk metallic glass under HP &; HT

The phase transitions in Pd₄₀Ni₁₀Cu₃₀P₂₀ bulk metallic glass (BMG) have been studied under high pressure and high temperature (HP & HT) by X-ray diffaction measurements with synchrotron radiation source. We found that the BMG underwent a phase transitions of amorphous-crystalline-amorphous at 10 GPa upon heating. The parallel experiments were carried out at 7 GPa, while we did not observe the amorphous-crystalline-amorphous transitions by increasing temperature. Quenching the melted BMG at 7 GPa, it was found that the phase crystallized from the melt differed from the primary phase crystallized from the starting amorphous solid upon heating suggesting there existed a distinct mechanism in two cases.     

Investigation on structural characteristics of PVDF–AgCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposite solid polymer electrolyte system

There has been an increasing interest towards the incorporation of nanosize ceramic fillers in polymer electrolytes. Solid polymer electrolytes based on polyvinylidene fluoride (PVDF), silver triflate (AgCF₃SO₃), and x wt% of aluminum oxide (Al₂O₃) nanopowders (where x = 1, 3, 5, and 10, respectively) have been prepared using solution casting technique. The structural characteristics of these thin film specimens were studied using Fourier transform infrared (FTIR) and X-ray diffraction (XRD) patterns at room temperature. The appearance of new absorption bands and gradual shifts observed in some characteristic peaks confirmed the complex formation between polyvinylidene fluoride and silver triflate. Furthermore, the addition of nanosized filler Al₂O₃ has also indicated the interaction of the filler with the polymer salt complex. The XRD patterns obtained for all these samples in the 2θ range 10° to 70° showed the amorphous nature of these samples. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006.     

Photosensitive structure from the tetragonal modification of ZnP<Subscript>2</Subscript> single crystals

Single crystals of ZnP₂ with a developed natural faceting characteristic of tetragonal symmetry were grown for the first time using a resublimation method. The atomic composition and crystal cell constants of t-ZnP₂ tetragonal crystals were determined. Structures that feature the straightening and photovoltaic effect covered the natural faces of the crystals. Studies of the photosensitivity of the obtained structures in natural and linearly polarized radiation made it possible to elucidate the character of interband transitions and to estimate the forbidden-band gap for the t-ZnP₂ crystals. Natural photopleochroism has been found and studied in structures based on single crystals with the natural faceting. It is concluded that ZnP₂ can be used as a highly efficient converter of solar radiation. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 76, No. 2, pp. 237–242, March–April, 2009.     

Characterization of Y<Subscript>2</Subscript>BaCuO<Subscript>5</Subscript> nanoparticles synthesized by nano-emulsion method

Nanoscale yttrium–barium–copper oxide (Y₂BaCuO₅, Y211) particles were synthesized using the emulsion method and the solution method. The basic water-in-oil (w/o) emulsion system consisted of n-octane (continuous oil phase), cetyltrimethylammonium bromide (cationic surfactant), butanol (cosurfactant) and water. The composition of the emulsion system was varied and characterized by measuring the conductivity of the solutions and droplet size. The droplet size of emulsion was determined by using the dynamic light scattering method. The water content, cosurfactant content, and surfactant/n-octane ratio affected the droplet size which was in the range of 3–8 nm, and hence the w/o emulsion system was referred to as a nano-emulsion system. A model was used to verify the droplet size. The influence of salt (Y₂(NO₃)₃) content on the droplet size was investigated and the addition of salt reduced the droplet size. The effects of reaction time and temperature on the Y211 particle sizes were also investigated. The particles were characterized using the TEM, SEM, and XRD. Nanoparticles produced by the nano-emulsion method were calcined at 850°C to form the Y211 phase as compared to solid state processing temperature of 1050°C. Based on the TEM analysis, the average diameter of the Y211 particles produced using the nano-emulsion method was in the range of 30–100 nm. The effect of adding 15% Y211 nanoparticles to the superconductor YBCO-123 as flux pinning centers, was investigated, and the transition temperature was reduced by 3 K.     

Effect of excess Y<Subscript>2</Subscript>O<Subscript>3</Subscript> addition on the physical properties of melt processed YBCO bulks

The YBCO superconductors with Y₂O₃ addition were prepared by a modified melt textured process and the effects of excess Y₂O₃ addition on the physical properties of melt textured YBCO have been investigated. It is found that the melt temperature of YBCO samples decreases drastically with the increasing Y₂O₃, and the maximum levitation forces are drastically different for samples with different Y₂O₃ addition. It is also found that the optimal Y₂O₃ addition to YBCO is about 10wt%. Considering the microstructure and the starting composition, the results are well discussed and interpreted.     

VUV luminescence of Er<Superscript>3+</Superscript> ions in LiYF<Subscript>4</Subscript> and BaY<Subscript>2</Subscript>F<Subscript>8</Subscript> crystals

Vacuum ultraviolet luminescence of Er³⁺ ions in LiYF4 and BaY₂F₈ crystals has been investigated. It is revealed that under excitation by 193 nm radiation from an ArF excimer laser the interconfigurational 5d–4f radiative transitions in Er³⁺ ions are observed. It is shown that from the LiYF₄:Er crystal only the spin-forbidden luminescence (λ = 165 nm) is detected, whereas both the spin-forbidden (λ = 169 nm) and spin-allowed (λ = 160.5 nm) components are observed from the BaY₂F₈:Er crystal.     

Absorption by CS<Subscript>2</Subscript> molecules on “hot” band emission lines from a TEA CO<Subscript>2</Subscript> laser

We have measured absorption of emission from a TEA CO₂ laser, lasing on hot band lines, in pure CS₂ and a mixture of CS₂ with air, and we have determined the optimal lines for optical excitation. Numerical modeling has shown that as the peak intensity of the pump radiation is increased, we observe absorption saturation, the extent of which decreases as the pressure increases. The major factor responsible for absorption saturation is the “rotational bottleneck” effect. Depending on the peak intensity of the radiation, addition of a buffer gas can lead to an increase or decrease in the absorption. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 1, pp. 61–66, January–February, 2007.     

Improvement of refrigerant capacity of La<Subscript>0.67</Subscript>Ca<Subscript>0.33</Subscript>MnO<Subscript>3</Subscript> single crystal with a few percent Fe doping

Large low-field-induced magnetic entropy changes, ΔS _M, are observed in La_0.67Ca_0.33MnO₃ and La_0.67Ca_0.33Mn_0.96Fe_0.04O₃ single crystals. The peaks of ΔS _M broadened asymmetrically to high temperatures under higher magnetic fields for two materials should be attributed to the first-order magnetic phase transition at T _c. A small amount of iron doping results in an increase in the refrigerant capacity of the material though the magnetic entropy change decreases. The discovery of excellent magnetocaloric features of these single crystals in the low magnetic field can provide some ideas for exploring novel magnetic refrigerants operating under permanent magnet rather than superconducting one as magnetic field source. Supported by the State Key Project of Fundamental Research (Grant No. 2005CB724402), and the National Natural Science Foundation of China (Grant No. 50672126) Contributed by CHENG ZhaoHua