Thermal oxide synthesis and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanorods and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanowires

Fe₃O₄ nanorods and Fe₂O₃ nanowires have been synthesized through a simple thermal oxide reaction of Fe with C₂H₂O₄ solution at 200–600°C for 1 h in the air. The morphology and structure of Fe₃O₄ nanorods and Fe₂O₃ nanowires were detected with powder X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The influence of temperature on the morphology development was experimentally investigated. The results show that the polycrystals Fe₃O₄ nanorods with cubic structure and the average diameter of 0.5–0.8 μm grow after reaction at 200–500°C for 1 h in the air. When the temperature was 600°C, the samples completely became Fe₂O₃ nanowires with hexagonal structure. It was found that C₂H₂O₄ molecules had a significant effect on the formation of Fe₃O₄ nanorods. A possible mechanism was also proposed to account for the growth of these Fe₃O₄ nanorods. Supported by the Fund of Weinan Teacher’s University (Grant No. 08YKZ008), the National Natural Science Foundation of China (Grant No. 20573072) and the Doctoral Fund of Ministry of Education of China (Grant No. 20060718010)     

Comparison of the Solubility of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>, Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> in High Temperature Water

As the solubility is a direct measure of stability, this study compares the solubilities of ZnFe₂O₄, Fe₃O₄ and Fe₂O₃ in high temperature water. Through literature analysis and formula derivation, it is shown that it is reasonable to assume ZnFe₂O₄ and Fe(OH)₃ coexist when ZnFe₂O₄ is dissolved in water. Results indicated that the solubility of ZnFe₂O₄ is much lower than that of Fe₂O₃ or Fe₃O₄. The low solubility of ZnFe₂O₄ indicates that it is more protectively stable as an anticorrosion phase. Moreover, the gap between the solubility of ZnFe₂O₄ and that of Fe₃O₄ or Fe₂O₃ was enlarged with an increase of temperature. This means that ZnFe₂O₄ is more protective at higher temperatures. Further analysis indicated that with the increase of temperature, the solubility of ZnFe₂O₄ changed little while those of Fe₂O₃ or Fe₃O₄ changed a lot. Little change of the solubility of ZnFe₂O₄ with increase of temperature showed that ZnFe₂O₄ is stable. The very low and constant solubility of ZnFe₂O₄ suggests that it is more protective than Fe₂O₃ and Fe₃O₄, especially in water at higher temperature.     

Catalytic Properties of TiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles in Plasma Chemical Treatment

We proposed here a new process coupling dielectric barrier discharge (DBD) plasma with magnetic photocatalytic material nanoparticles for improving yield in DBD degradation of methyl orange (MO). TiO₂ doped Fe₃O₄ (TiO₂/Fe₃O₄) was prepared by the sol-gel method and used as a new type of magnetic photocatalyst in DBD system. It was found that the introduction of TiO₂/Fe₃O₄ in DBD system could effectively make use of the energy generated in DBD process and improve hydroxyl radical contributed by the main surface Fenton reaction, photocatalytic reaction and catalytic decomposition of dissolved ozone. Most part of MO (88%) was degraded during 30 min at peak voltage of 13 kV and TiO₂/Fe₃O₄ load of 100 mg/L, with a rate constant of 0.0731 min^?1 and a degradation yield of 7.23 g/(kW h). The coupled system showed higher degradation efficiency for MO removal.     

Adsorption behavior of <Superscript>99</Superscript>Tc on Fe,Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> and Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>

Summary The adsorption of ⁹⁹Tc on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ was studied by batch experiments under aerobic and anoxic conditions. The effects of pH and CO₃^2- concentration of the simulated ground water on the adsorption ratios were also investigated, and the valences of Tc in solution after the adsorption equilibrium were studied by solvent extraction. The adsorption isotherms of TcO₄- on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ were determined. Experimental results have shown that the adsorption ratio of Tc on Fe decreases with the increase of pH in the range of 5-12 and increases with the decrease of the CO₃^2- concentration in the range of 10^-8M-10^-2M. Under aerobic conditions, the adsorption ratios of ⁹⁹Tc on Fe₂O₃ and Fe₃O₄ were not influenced by pH and CO₃^2-concentration. When Fe was used as adsorbent, Tc existed mainly in the form of Tc(IV) after equilibrium and in the form of Tc(VII) when the adsorbent was Fe₂O₃ or Fe₃O₄ under aerobic conditions. The adsorption ratios of Tc on Fe, Fe₂O₃ and Fe₃O₄ decreased with the increase of pH in the range of 5-12 and increased with the decrease of the CO₃^2- concentration in the range of 10^-8M-10^-2M under anoxic conditions. Tc existed mainly in the form of Tc(IV) after equilibrium when Fe, Fe₂O₃ and Fe₃O₄ was the adsorbent under anoxic conditions. The adsorption isotherms of TcO_4- on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ are fairly in agreement with the Freundlich’s equation under both aerobic and anoxic conditions.     

Thiol-functionalized Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/SiO<Subscript>2</Subscript> microspheres with superparamagnetism and their adsorption properties for Au(III) ion separation

Thiol-functionalized Fe₃O₄/SiO₂ microspheres (Fe₃O₄/SiO₂-SH) with high saturation magnetization (69.3 emu g^–1), superparamagnetism, and good dispersibility have been prepared by an ethylene glycol reduction method in combination with a modified Stöber method. The as-prepared composite magnetic spheres are characterized with fourier transform infrared spectroscopy (FT-IR), zeta potential, X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and superconducting quantum interference magnetometer, and tested in separation of Au(III) ions from aqueous solutions. The data for Au(III) adsorption on Fe₃O₄/SiO₂-SH are analyzed with the Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich isotherm models, and the pseudo-first-order, pseudo-second-order, and intraparticle diffusion kinetics models. The adsorption behaviors of Au(III) on Fe₃O₄/SiO₂-SH follow the Langmuir isotherm model, and the adsorption process conforms to the pseudo-second-order kinetic model. The maximum adsorption capacity of Au(III) on Fe₃O₄/SiO₂-SH is 43.7 mg g^–1. Acetate anions play an important role yet Cu(II) ions have little interference in the adsorption of Au(III) on the adsorbent. A satisfactory recovery percentage of 89.5% is acquired by using an eluent with 1 M thiourea and 5% HCl, although thiols have a high affinity to Au(III) ions based on the hard-soft acid-base (HSAB) theory by Pearson.     

Improving Pullulanase Catalysis via Reversible Immobilization on Modified Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@Polydopamine Nanoparticles

To improve the catalysis of pullulanase from Anoxybacillus sp.WB42, Fe₃O₄@polydopamine nanoparticles (Fe₃O₄@PDA) were prepared and modified with functional groups for immobilization of pullulanases via covalent binding or ionic adsorption. Immobilized pullulanases had lower thermal stability than that of free pullulanase, whereas their catalysis depended on the surface characteristics of nanoparticles. As for covalent immobilization of pullulanases onto Fe₃O₄@PDA derivatives, the spacer grafted onto Fe₃O₄@PDA made the catalytic efficiency of pullulanase increase up to the equivalence of free enzyme but dramatically reduced the pullulanase thermostability. In contrast, pullulanases bounded ionically to Fe₃O₄@PDA derivatives had higher activity recovery and catalytic efficiency, and their catalytic behaviors varied with the modifier grafted onto Fe₃O₄@PDA. Among these immobilized pullulanases, ionic adsorption of pullulanase on Fe₃O₄@PDA-polyethyleneimine-glycidyltrimethylammonium gave a high-performance and durable catalyst, which displayed not only 1.5-fold increase in catalytic efficiency compared to free enzyme but also a significant improvement in operation stability with a half of initial activity after 27 consecutive cycles with a total reaction time of 13.5 h, and was reversible, making this nanoparticle reusable for immobilization.     

Preparation and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>composite particles

Using Fe₃O₄ nano-particles as seeds, a new type of Fe₃O₄/Au composite particles with core/shell structure and diameter of about 170 nm was prepared by reduction of Au³⁺ with hydroxylamine in an aqueous solution. Particle size analyzer and transmission electron microscope were used to analyze the size distribution and microstructure of the particles in different conditions. The result showed that the magnetically responsive property and suspension stability of Fe₃O₄ seeds as well as reduction conditions of Au³⁺to Au⁰are the main factors which are crucial for obtaining a colloid of the Fe₃O₄/Au composite particles with uniform particle dispersion, excellent stability, homogeneity in particle sizes, and effective response to an external magnet in aqueous suspension solutions. UV-Vis analysis revealed that there is a characteristic peak of Fe₃O₄/Au fluid. For particles with d(0.5)=168 nm, the λmax is 625 nm.     

Preparation and Characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@SiO<Subscript>2</Subscript> Nanoparticles Incorporated Polymer Monolithic Column for Gas Chromatography

We report on the synthesis of Fe₃O₄@SiO₂ nanoparticles incorporated poly(divinylbenzene) monolithic column via in situ polymerization. The monolith had larger specific surface area and relatively uniform porous structure and was characterized by scanning electron microscopy, nitrogen adsorption–desorption, and Fourier transform infrared spectroscopy. The monolith was then applied for the evaluation of gas chromatography separation properties. Here, an electromagnetic induction heating technique was employed to control the column temperature with the thermal effect of eddy current in ferromagnetic materials Fe₃O₄. The monolith offered good separation efficiency for benzene and toluene and a higher column efficiency was obtained up to 4481 and 9216 plates per meter, respectively. In addition, the injection volume and column capacity of the proposed system are as much as 5 µL and 100 ng. This makes it possible to use a UV detector. The fabricated Fe₃O₄@SiO₂ nanoparticles incorporated poly(divinylbenzene) monolithic column has been shown to be very promising for gas chromatography separation.

Graphical Abstract

Open image in new window

     

Preparation and Application of Magnetically Recoverable Cationic Exchanger Support on Monodisperse Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles

A magnetically recoverable cationic exchanger has been effectively prepared through immobilized chloroacetic acid (CA) onto the Fe₃O₄ nanoparticles. The magnetic nanoparticles (MNPs) were synthesized by a coprecipitation method in an aqueous system. The MNPs were modified with sodium silicate and chloroacetic acid (CA), thus endowed these nanoparticles with strong magnetism and good dispersion. The physicochemical properties of the cationic exchange materials were characterized with Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), X-ray diffraction (XRD) and thermal gravimetric analysis (TGA). The magnetic properties of the cationic exchange materials were analyzed by a vibrating sample magnetometer (VSM). The content of ions was measured by atomic absorption spectrophotometric method. The prepared cationic exchange nanoparticles display an excellent magnetic property with a saturation magnetization value of 26.58 emu/g and the prepared exchanger possess considerable thermal stability, which indicating a great potential application in heavy metal ion wastewater treatment. In this experiment, the exchange capacity of lead ion was 3.4 mmol g^–1, And the maximum lead removal rate is up to 73.85%.     

Thermal behavior of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> mesoporous gels

Summary Titania-based photocatalytic materials were prepared by sol-gel method using Fe³⁺ and polyethyleneglycol (PEG₆₀₀) as additives. Thermogravimetry (TG), differential thermal analysis (DTA) and evolved gas analysis (EGA) with MS detection were used to elucidate processes that take place during heating of Fe³⁺ containing titania gels. The microstructure development of the Fe₂O₃/TiO₂ gel samples with and without PEG₆₀₀ admixtures was characterized by emanation thermal analysis (ETA) under in situ heating in air. A mathematical model was used for the evaluation of ETA results. Surface area and porosity measurements of the samples dried at 120&deg;C and the samples preheated for 1 h to 300 and 500&deg;C were compared. From the XRD measurements it was confirmed that the crystallization of anatase took place after thermal heating up to 600&deg;C.     

Effect of SO<Subscript>2</Subscript> on chlorination of zinc ferrite ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> and a mixture of ZnO and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>

Results of thermodynamic calculations and kinetic studies of the reaction of zinc ferrite ZnFe₂O₄ and of a mixture of oxides, ZnO and Fe₂O₃, with chlorine and SO₂ are presented.     

Effect of SO<Subscript>2</Subscript> on chlorination of Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> + Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> mixtures

The reaction of Bi₂O₃ + Fe₂O₃ mixtures with chlorine and SO₂ at 250–700°C is studied. At 300–500°C, the degree of bismuth chloride sublimation from the oxide mixture increases in the presence of SO₂. Chemical sublimation of FeCl₃ occurs after BiCl₃ is virtually completely recovered from the solid phase.     

Obtaining of Ni<Subscript>0.65</Subscript>Zn<Subscript>0.35</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>/SiO<Subscript>2</Subscript> nanocomposites by thermal decomposition of complex compounds embedded in silica matrix

This article presents the results of our investigation on the obtaining of Ni_0.65Zn_0.35Fe₂O₄ ferrite nanoparticles embedded in a SiO₂ matrix using a modified sol–gel synthesis method, starting from tetraethylorthosilicate (TEOS), metal (Fe^III,Ni^II,Zn^II) nitrates and ethylene glycol (EG). This method consists in the formation of carboxylate type complexes, inside the silica matrix, used as forerunners for the ferrite/silica nanocomposites. We prepared gels with different compositions, in order to obtain, through a suitable thermal treatment, the nanocomposites (Ni_0.65Zn_0.35Fe₂O₄)_x–(SiO₂)_100–x (where x=10, 20, 30, 40, 50, 60 mass%). The synthesized gels were studied by differential thermal analysis (DTA), thermogravimetry (TG) and FTIR spectroscopy. The formation of Ni–Zn ferrite in the silica matrix and the behavior in an external magnetic field were studied by X-ray diffraction (XRD) and quasi-static magnetic measurements (50 Hz).     

Nonstoichiometric Zn Ferrite and ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> Composite Spheres: Preparation,Magnetic Properties,and Chromium Removal

Monodisperse and porous nonstoichiometric Zn ferrite can be prepared by a solvothermal method. Such non-Zn ferrite was used to be the precursor for synthesis of ZnFe₂O₄/Fe₂O₃ composite via calcination at 600°C for 3 h in air. X-ray powder diffractometer (XRD) and Energy Dispersive Spectrometer (EDS) proved the nonstoichiometry of Zn ferrite synthesized by solvothermal method and the formation of ZnFe₂O₄/Fe₂O₃ composite via calcination. TEM image showed that non-Zn ferrite spheres with wormlike nanopore structure were made of primary nanocrystals. BET surface area of non-Zn ferrite was much higher than that of ZnFe₂O₄/Fe₂O₃ composite. Saturation magnetization of non-Zn ferrites was significantly higher than that of ZnFe₂O₄/Fe₂O₃ composites. Calcination of non-Zn ferrite resulted in the formation of large amount of non-magnetic Fe₂O₃,which caused a low magnetization of composite. Because of higher BET surface area and higher saturation magnetization, non-Zn ferrite presented better Cr⁶⁺ adsorption property than ZnFe₂O₄/Fe₂O₃ composites.     

Microwave and UV Assisted Methods for Obtaining Novel Composites Based on Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> with Embedded Gold Nanoparticles

Metallic nanoparticles embedded into the structure of metal oxides may play a role of catalytic substances. Such composites are mostly applied in oxidation reactions. The paper presents two one-step-methods for obtaining nanocomposites of gold embedded in the structure of iron oxide matrices (nanoAu/Fe₂O₃). Gold nanoparticles were formed in situ in the process of iron hydroxide dehydration. Thanks to the use of tannic acid it was possible to effectively reduce gold ions and stabilize the forming metal nanoparticles. The composites were prepared in the fields of microwave, ultraviolet radiation. The physicochemical properties of products were determined by scanning electron microscopy, energy-dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy, X-ray analysis and high-resolution transmission electron microscopy technique with EDS and elemental mapping mode. Also, the catalytic activity of the nanocomposites obtained was evaluated based on the process of methyl orange degradation. It was observed that products obtained according to the microwave radiation method are characterized by improved applying properties.     

Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/Au composite nano-particles and their optical properties

Fe₃O₄/Au composite particles with core/shell structure were prepared by reduction of Au³⁺ with hydroxylamine in the presence of an excess of Fe₃ O₄ as seeds. The resultant colloids, with an average diameter of less than 100 nm, were obtained; the remaining non-reacted Fe₃O₄ seeds can be removed by treatment with diluted HCl solution. The Fe₃O₄/Au colloids exhibit a characteristic peak of UV-visible spectra, which largely depend on the size of the particle and the suspension medium. The localized surface plasmon resonance peaks red shift and broaden with increased nanoparticle diameter or increased solvent ionic strength. The optical property is very important in the establishment of means for the detection of biomolecules.     

Surface chemistry of nanoscale Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> dispersed in magnetic fluids

The interaction between stabilizers and nanoparticles is one of the important factors to prepare stable magnetic fluids. The magnetic nano-size Fe₃O₄ core with single domain and the average grain size around 8–12 nm were prepared by chemical precipitation method. The O/Fe molar ratio of the particle surface was measured by X-ray photoelectron spectroscopy (XPS). The heat effects of stabilizers adsorption on nanoparticles were measured by solution calorimetry. The excess amount of oxygen was possibly the result of the hydroxygen formed on the surface of the nanoparticles. The heat effects showed that compounds containing carboxyl groups can be adsorbed chemically on magnetite by forming chemical bonds. The other stabilizers involving NH-groups, such as polyethylene-imine, can be adsorbed physically. The exothermic value is about half of the former case. Supported by the National Natural Science Foundation of China (Grant No. 50476039), and Guangdong Provincial Department of Science and Technology (Grant No. 2004A10-703001)