Automated hollow fiber-protected dynamic liquid-phase microextraction of pesticides for gas chromatography-mass spectrometric analysis

Dynamic liquid-phase microextraction (LPME) controlled by a programmable syringe pump was evaluated for extracting pesticides in water prior to GC-MS analysis. A conventional microsyringe with a 1.3-cm length of hollow fiber attached to its needle was connected to a syringe pump to perform the extraction. The microsyringe was used as both the microextraction device as well as the sample introduction device for GC-MS analysis. The attached hollow fiber served as the "holder" and protector" of 3 microl of organic solvent. The solvent was repeatedly withdrawn into and discharged from the hollow fiber by the syringe pump. Pesticides were extracted from 4-ml water samples into the organic solvent impregnated in the hollow fiber. The effects of organic solvents, plunger movement pattern, agitation and extraction time were investigated. Good repeatabilities of extraction performance were obtained, with the RSD values ranging from 3.0% (alachlor) to 9.8% (4-chlorophenol) for the 14 pesticides; most RSD values were under 5.0%. The method provided a 490-fold preconcentration of the target pesticides. The limits of detection were in the range of 0.01-5.1 microg/l (S/N = 3) in the GC-MS selected ion monitoring mode. In addition, sample clean-up was achieved during LPME because of the selectivity of the hollow fiber, which prevented undesirable large molecules from being extracted. A slurry sample (mixture of 40 mg soil/ml of water) containing seven pesticides was extracted using this method which also gave good linearity and precision (most RSDs <7.0%, n = 3).     

A liquid-phase microextraction method, combining a dual gauge microsyringe with a hollow fiber membrane, for the determination of organochlorine pesticides in aqueous solution by gas chromatography/ion trap mass spectrometry

A liquid-phase microextraction (LPME) method has been demonstrated for the extraction and determination of organochlorine pesticides (OCPs) in aqueous solution. The method combines a dual gauge microsyringe with a hollow fiber membrane (LPME/DGM-HF) followed by detection by gas chromatography/ion trap mass spectrometry (GC/ITMS). The advantages include speed, low solvent and sample consumption, simplicity and ease of use. The extraction time, solvent selection, salt concentration and sample stirring rate have been investigated in order to optimize extraction efficiency. The viability is evaluated by measuring the linearity and detection limit of the five OCPs in aqueous solution. Detection linearity for the OCPs has been achieved over a range of concentrations between 1 and 500 microg/L (r2 > 0.930), with a detection limit of 0.1 microg/L for each OCP.     

Application of SiO2 hollow fibers for sorptive microextraction and gas chromatography–mass spectrometry determination of organochlorine pesticides in herbal matrices

A method involving simultaneous extraction and sample clean-up procedure: hollow fiber sorptive microextraction, coupled with gas chromatography–mass spectrometric detection for quantification of seven organochlorine pesticides in Radix et Rhizoma Rhei is described. SiO₂ hollow fiber with porous structure was synthesized for the first time. The internal diameter of SiO₂ hollow fiber is 380 μm and average wall thickness is 100 μm. Aggregated SiO₂ particles deposited on the surface of the hollow fiber in a regular array lead to porous structure. SiO₂ hollow fiber was applied to the determination of organochlorine pesticides in Radix et Rhizoma Rhei to avoid sample clean-up and minimize the matrix effects. Extraction solvent, extraction temperature and equilibration time were optimized. Fiber to fiber repeatability over the concentration ranges were less than 10%. Recoveries were satisfactory (between 63% and 115%) for most of organochlorine pesticides at spiking levels. Furthermore, the proposed method was also applied to determine seven organochlorine pesticides in 43 commercial Radix et Rhizoma Rhei samples, in which the selected pesticides were found in eight samples. The results have been further confirmed by solvent extraction methods according to China Pharmacopoeia (2005).     

Analysis of organochlorine pesticides in wine by solvent bar microextraction coupled with gas chromatography with tandem mass spectrometry detection

A solvent bar microextraction (SBME) technique combined with gas chromatography/tandem mass spectrometry (GC/MS/MS), for the determination of selected organochlorine pesticides (OCPs) in wine samples, is described. In this work the OCPs were extracted and dissolved in a 2-microL aliquot of organic extraction solvent (n-tetradecane) confined within a 1.7-cm length of hollow fiber. Both ends of the hollow fiber (solvent bar) were sealed, and it was placed in an aqueous sample solution for extraction. The effects of solvent selection, sample agitation, extraction time, extraction temperature, and salt concentration on the SBME performance were optimized. The influence of aqueous sample/organic solvent phase ratio was further investigated in detail. High enrichments (1900-7100-fold) could be obtained at an aqueous sample/organic solvent volume ratio of 20 mL/2 microL in this study. Good extraction reproducibility was obtained with relative standard deviation (RSD) values below 12.6%. Comparisons of sensitivity and precision between SBME and dynamic hollow-fiber liquid-phase microextraction were also investigated.     

Determination of organochlorine pesticides in water using solvent cooling assisted dynamic hollow-fiber-supported headspace liquid-phase microextraction

The organic solvent film formed within a hollow fiber was used as an extraction interface in the headspace liquid-phase microextraction (HS-LPME) of organochlorine pesticides. Some common organic solvents with different vapor pressures (9.33-12,918.9 Pa) were studied as extractants. The results indicated that even the solvent with the highest vapor pressure (cyclohexane) can be used to carry out the extraction successfully. However, those compounds (analytes) with low vapor pressures could not be extracted successfully. In general, the large surface area of the hollow fiber can hasten the extraction speed, but it can increase the risk of solvent loss. Lowering the temperature of the extraction solvent could not only reduce solvent loss (by lowering its vapor pressure) but also extend the feasible extraction time to improve extraction efficiency. In this work, a solvent cooling assisted dynamic hollow-fiber-supported headspace liquid-phase microextraction (SC-DHF-HS-LPME) approach was developed. By lowering the temperature of the solvent, the evaporation can be decreased, the extraction time can be lengthened, and, on the contrary, the equilibrium constant between headspace phase and extraction solvent can be increased. In dynamic LPME, the extracting solvent is held within a hollow fiber, affixed to a syringe needle and placed in the headspace of the sample container. The extracting solvent within the fiber is moved to-and-fro by using a programmable syringe pump. The movement facilitates mass transfer of analyte(s) from the sample to the solvent. Analysis of the extract was carried out by gas chromatography-mass spectrometry (GC-MS). The effects of identity of extraction solvent, extraction temperature, sample agitation, extraction time, and salt concentration on extraction performance were also investigated. Good enrichments were achieved (65-211-fold) with this method. Good repeatabilities of extraction were obtained, with RSD values below 15.2%. Detection limits were 0.209 microg/l or lower.     

Liquid-liquid-liquid microextraction of nitrophenols with a hollow fiber membrane prior to capillary liquid chromatography

A simple liquid-liquid-liquid microextraction device utilizing a 2 cm x 0.6 mm I.D. hollow fiber membrane was used to preconcentrate nitrophenols from water sample prior to capillary liquid chromatography (cLC) analysis. The extraction procedure was induced by the pH difference inside and outside the hollow fiber. The donor phase outside the hollow fiber was adjusted to pH approximately 1 with HCl; the acceptor phase was NaOH solution used at various concentrations. Organic solvent was immobilized into the pores of the hollow fiber. With stirring, the neutral nitrophenols outside the fiber were extracted into the organic solvent, then back extracted into 2 microl of basic acceptor solution inside the fiber. The acceptor phase was then withdrawn into a microsyringe and injected into the cLC system directly. This technique used a low-cost disposable extraction "device" and is very convenient to operate. Up to 380-fold enrichment of analytes could be achieved. This procedure could also serve as a sample clean-up step because large molecules and basic compounds were not extracted into the acceptor phase. The RSD (n=6) was less than 6.2%, while the linear calibration range was from 1 to 200 microg/ml with r>0.998. The procedure was applied to the analysis of seawater.     

Development and application of polymer-coated hollow fiber membrane microextraction to the determination of organochlorine pesticides in water

A novel extraction procedure coupled with gas chromatography-mass spectrometric detection for quantification of organochlorine pesticides (OCPs) in water is described. Amphiphilic polyhydroxylated polyparaphenylene (PH-PPP) was synthesized and coated on the surfaces of a porous polypropylene hollow fiber membrane (HFM). Due to the high porosity of the HFM, maximum active surface area to achieve high extraction efficiency is expected. The polymer-coated HFM was used for the extraction of 15 OCPs from water. The extraction efficiency was compared with emerging and established methods such as liquid-phase microextraction (LPME), solid-phase microextraction (SPME) and stir bar sorptive extraction (SBSE) techniques. We term the current procedure as polymer-coated hollow fiber microextraction (PC-HFME). PC-HFME showed good selectivity and sensitivity. Detection limits for OCPs were in the range of 0.001-0.008 microg l(-1). The sensitivity and selectivity of the coated HFM could be adjusted by changing the characteristics of the coated PH-PPP film.     

Determination of pesticides in soil by liquid-phase microextraction and gas chromatography-mass spectrometry

Trace amounts of pesticides in soil were determined by liquid-phase microextraction (LPME) coupled to gas chromatography-mass spectrometry (GC-MS). The technique involved the use of a small amount (3 microl) of organic solvent impregnated in a hollow fiber membrane, which was attached to the needle of a conventional GC syringe. The organic solvent was repeatedly discharged into and withdrawn from the porous polypropylene hollow fiber by a syringe pump, with the pesticides being extracted from a 4 ml aqueous soil sample into the organic solvent within the hollow fiber. Aspects of the developed procedure such as organic solvent selection, extraction time, movement pattern of plunger, concentrations of humic acid and salt, and the proportion of organic solvent in the soil sample, were optimized. Limits of detection (LOD) were between 0.05 and 0.1 microg/g with GC-MS analysis under selected-ion monitoring (SIM). Also, this method provided good precision ranging from 6 to 13%; the relative standard deviations were lower than 10% for most target pesticides (at spiked levels of 0.5 microg/g in aqueous soil sample). Finally, the results were compared to those achieved using solid-phase microextraction (SPME). The results demonstrated that LPME was a fast (within 4 min) and accurate method to determine trace amounts of pesticides in soil.     

固相萃取-气相色谱法测定茶叶中残留的92种农药

建立了茶叶中92种农药多残留的气相色谱分析方法。茶叶样品用乙腈一次性提取后,有机磷类农药经Envi-Carb固相小柱净化,用10 mL乙腈-甲苯(体积比为3∶1)洗脱剂淋洗,气相色谱-火焰光度检测器(GC-FPD)检测;有机氯类和拟除虫菊酯类农药经串联Envi-Carb和NH2固相小柱净化,用5 mL乙腈-甲苯(体积比为3∶1)洗脱剂淋洗,GC-电子捕获检测器(ECD)检测。采用外标法定量。添加回收试验的结果表明:92种农药的平均回收率为80.3%～117.1%,相对标准偏差为1.5%～9.8%。方法的检出限为0.0025～0.10 mg/kg。该方法的灵敏度、准确度和精密度均符合农药残留测定的技术要求。     

Application of continual injection liquid‐phase microextraction method coupled with liquid chromatography to the analysis of organophosphorus pesticides

A liquid‐phase microextraction coupled with LC method has been developed for the determination of organophosphorus pesticides (methidation, quinalphos and profenofos) in drinking water samples. In this method, a small amount (3 μL) of isooctane as the acceptor phase was introduced continually to fill‐up the channel of a 1.5 cm polypropylene hollow fiber using a microsyringe while the hollow fiber was immersed in an aqueous donor solution. A portion of the acceptor phase (ca. 0.4 μL) was first introduced into the hollow fiber and additional amounts (ca. 0.2 μL) of the acceptor phase were introduced to replenish at intervals of 3 min until set end of extraction (40 min). After extraction, the acceptor phase was withdrawn and transferred into a 2 mL vial for a drying step prior to injection into a LC system. Parameters that affect the extraction efficiency were studied including the organic solvent, length of fiber, volume of acceptor and donor phase, stirring rate, extraction time, and effect of salting out. The proposed method provided good enrichment factors of up to 189.50, with RSD ranging from 0.10 to 0.29%, analyte recoveries of over 79.80% and good linearity ranging from 10.0 to 1.25 mg/L. The LOD ranged from 2.86 to 82.66 μg/L. This method was applied successfully to the determination of organophosphorus pesticides in selected drinking water samples.     

Application of static liquid-phase microextraction to the analysis of organochlorine pesticides in water.

Static liquid-phase microextraction, with subsequent analysis by gas chromatography-electron-capture detection, has been applied to extract eight organochlorine pesticides from water. A conventional microsyringe was used to extract analytes from water samples over a concentration range of 0.05-100 microg/l. Factors relevant to the extraction process were investigated. The sensitivity of the method was enhanced with agitation, and increasing the extraction temperature, of the sample solution. Concentration factors of >50-fold were easily achieved within 25 min of extraction. The analytical data exhibited a relative standard deviation (RSD) range of 3.2% (lindane) to 10.7% (methoxychlor) for the eight pesticides; most RSD values were under 7%. Water samples collected from a reservoir, and from tap water in a chemical laboratory were analyzed using the procedure.     

Simultaneous Analysis of Carbamate and Organophosphorus Pesticides in Water by Single-Drop Microextraction Coupled with GC–MS

Single-drop microextraction (SDME) has been coupled with gas chromatography–mass spectrometry to enable rapid and simple simultaneous analysis of carbamate and organophosphorus pesticides (OPP). The significant conditions affecting SDME performance (microextraction solvent, extraction time, solvent volume, sample pH, stirring speed, and ionic strength) were studied and optimized. Extraction was achieved by suspending a 1.5-μL drop of toluene from the tip of a microsyringe directly immersed in 5-mL aqueous donor solution at pH 5 stirred at 800 rpm. The dynamic linear range and detection limits of the method were evaluated by analysis of water samples spiked with carbamate pesticides and OPP. Under selected ion-storage mode, very low detection limits (0.02–0.50 ng mL^?1) and good linearity (0.5–200 ng mL^?1) were achieved. When SDME was applied to analysis of pesticides in natural water samples good recoveries (89.4–102.1%) were obtained. Inter-day and intra-day RSD of most results were below 5.4 and 6.1%, respectively. The method proved to be a rapid and simple tool for extraction and analysis of these pesticides in water samples.     

Application of polyphenylmethylsiloxane coated fiber for solid-phase microextraction combined with microwave-assisted extraction for the determination of organochlorine pesticides in Chinese teas

Polyphenylmethylsiloxane (PPMS) as a novel coating for solid-phase microextraction (SPME) combined with microwave-assisted extraction (MAE) has been applied to determine the concentrations of organochlorine pesticides (OCPs) in Chinese teas. The characteristics of PPMS fiber, the extraction modes of SPME, the extraction time, temperature, and salt effects were investigated. Microwave irradiation time and power were also studied. Compared with commercial polydimethylsiloxane (PDMS) fiber and homemade sol-gel polymethylsiloxane (PMS) fiber, the novel porous sol-gel PPMS fiber exhibited high sensitivity and selectivity for OCPs compounds, higher thermal stability (to 350 degrees C) and long service life (more than 150 times). The recoveries of MAE is compared with that of ultrasonic extraction (USE), MAE-SPME-gas chromatography (GC)/electron-capture detection (ECD) methods showed better results for Chinese teas. Linear ranges of OCPs in the blank green tea was 0.1-10(3) ng/l. Detection limits of this method are below 0.081 ng/l. Recoveries of this method are between 39.05 and 94.35%. The repeatability of the technique was less than 16% relative standard deviation (R.S.D.). The tested pesticides in three Chinese teas were at the ng/g level.     

Development and application of microporous hollow fiber protected liquid-phase microextraction via gaseous diffusion to the determination of phenols in water

A new organic solvent-free microextraction technique termed liquid-gas-liquid microextraction (LGLME) was developed. In this technique, a small amount (6 microl) of aqueous acceptor solution (0.5M NaOH) is introduced into the channel of a 2.65 cm polypropylene hollow fiber. The hollow fiber is then immersed in an aqueous sample donor solution. The aqueous acceptor phase in the channel of the hollow fiber is separated from the sample solution by the hydrophobic microporous hollow fiber wall with air inside its pores. The analytes (phenols) passed through the microporous hollow fiber membrane by gas diffusion and were then trapped by the basic acceptor solution. After extraction, the acceptor solution was withdrawn into a microsyringe and injected into a capillary electrophoresis sample vial for subsequent analysis. Limits of detection of between 0.5 and 10 microg/l for eight phenols could be achieved. The relative standard deviations (n=6) of this technique between 2.7 and 7.6%. The technique also provides good enrichment factors for all the eight analytes.     

Comparison of pressurized liquid extraction and microwave assisted extraction for the determination of organochlorine pesticides in vegetables

A method to determine organochlorine pesticides in horticultural samples (lettuce, tomato, spinach, potato, turnip leaf and green bean) using pressurized liquid extraction (PLE) is described and compared with microwave assisted extraction (MAE). Significant parameters affecting PLE procedure such as temperature, static extraction time and extraction solvent were optimised and discussed. Clean-up of extracts was performed by solid phase extraction (SPE) using a carbon cartridge as adsorbent. Pesticides were determined by gas chromatography and electron capture detection (GC-ECD). Analytical recoveries obtained were ca. 100% and the relative standard deviations were lower than 15% for most of the studied pesticides with the proposed methods in each analysed matrix.     

Electrodeposited polyaniline as a fiber coating for solid-phase microextraction of organochlorine pesticides from water

The study on the performance of polyaniline as a fiber coating for solid-phase microextraction (SPME) purposes has been reported. Polyaniline coatings were directly electrodeposited on the surface of a stainless steel wire and applied for the extraction of some organochlorine pesticides (OCPs) from water samples. Analyses were performed using GC-electron capture detection (GC-ECD). The results obtained show that polyaniline fiber coating is suitable for the successful extraction of organochlorine compounds. This behavior is most probably due to the porous surface structure of polyaniline film, which provides large surface areas and allowed for high extraction efficiency. Experimental parameters such as adsorption and desorption conditions were studied and optimized. The optimized method has an acceptable linearity, with a concentration range of 1-5000 ng/L. Single fiber repeatability and fiber-to-fiber reproducibility were less than 12 and 17%, respectively. High environmental resistance and lower cost are among the advantages of polyaniline fibers over commercially available SPME fibers. The developed method was applied to the analysis of real water samples from Yangtse River and Tianmu Lake.     

Gas purge microsyringe extraction for quantitative direct gas chromatographic-mass spectrometric analysis of volatile and semivolatile chemicals

Sample pretreatment before chromatographic analysis is the most time consuming and error prone part of analytical procedures, yet it is a key factor in the final success of the analysis. A quantitative and fast liquid phase microextraction technique termed as gas purge microsyringe extraction (GP-MSE) has been developed for simultaneous direct gas chromatography-mass spectrometry (GC-MS) analysis of volatile and semivolatile chemicals without cleanup process. Use of a gas flowing system, temperature control and a conventional microsyringe greatly increased the surface area of the liquid phase micro solvent, and led to quantitative recoveries of both volatile and semivolatile chemicals within short extraction time of only 2 min. Recoveries of polycyclic aromatic hydrocarbons (PAHs), organochlorine pesticides (OCPs) and alkylphenols (APs) determined were 85-107%, and reproducibility was between 2.8% and 8.5%. In particular, the technique shows high sensitivity for semivolatile chemicals which is difficult to achieve in other sample pretreatment techniques such as headspace-liquid phase microextraction. The variables affecting extraction efficiency such as gas flow rate, extraction time, extracting solvent type, temperature of sample and extracting solvent were investigated. Finally, the technique was evaluated to determine PAHs, APs and OCPs from plant and soil samples. The experimental results demonstrated that the technique is economic, sensitive to both volatile and semivolatile chemicals, is fast, simple to operate, and allows quantitative extraction. On-site monitoring of volatile and semivolatile chemicals is now possible using this technique due to the simplification and speed of sample treatment.     

加速溶剂萃取/凝胶渗透色谱－固相萃取净化、气相色谱－质谱法测定茶叶中残留的33种农药

建立了茶叶中有机磷、有机氯、拟除虫菊酯类共33种农药残留的分析方法。样品以丙酮-二氯甲烷(体积比为1:1)为提取剂经加速溶剂方法萃取,提取液用凝胶渗透色谱净化除去大部分的色素、脂类和蜡质,再用Carb-NH2小柱和Florisil小柱净化。采用气相色谱法分析、外标法定量、气相色谱-质谱法（GC-MS）定性。加标水平为0.05 mg/kg时,大部分农药的回收率为70%~120%,相对标准偏差小于20%。方法的检测限为0.005～0.05 mg/kg (以10倍信噪比计)。该方法的提取效率高,准确灵敏,目前已应用于出口茶叶中农药残留的日常检测。大量实际样品的检测结果表明,此方法适于出口茶叶中农药残留检测实际工作的需要。     

Optimization of nonequilibrium liquid-phase microextraction for the determination of nitrobenzenes in aqueous samples by gas chromatography-electron capture detection.

In the present work, a novel method for the determination of nitrobenzenes in water has been described. It is based on nonequilibrium liquid-phase microextraction and gas chromatography-electron capture detection (GC-ECD). Extraction conditions such as solvent selection, organic solvent dropsize, stirring rate, content of NaCl and extraction time were found to have significant influence on extraction efficiency. The optimized conditions were 1.5 microl toluene and 20 min extraction time at 400 rpm stirring rate without NaCl addition. The linear range was 0.1 - 50 microg l(-1) for most nitrobenzenes. The limits of detection (LODs) ranged from 0.02 microg l(-1) (for 2.6-DNT) to 0.4 microg l(-1) (for NB); and relative standard deviations (RSD) for most of the nitrobenzenes at the 10 microg l(-1) level, except for 2,6-DNT in 3 microg l(-1), were below 10%. Natural samples collected from Miyun Reservoir and tap water samples from a laboratory were successfully analyzed using the proposed method, but none of the analytes were detected. The relative recoveries of spiked water samples (at the 10 microg l(-1) level except for 2,6-DNT in 3 microg l(-1)) were from 82.6 to 118.7%.     

Optimization of a multi-residue screening method for the determination of 85 pesticides in selected food matrices by stir bar sorptive extraction and thermal desorption GC-MS

A multi-residue method to determine 85 pesticides, including organochlorine pesticides, carbamates, organophosphorus pesticides, and pyrethroids, in vegetables, fruit, and green tea, has been developed. The method is based on stir bar sorptive extraction (SBSE) coupled to thermal desorption (TD) and retention time locked (RTL) GC-MS operating in the scan mode. Samples are extracted with methanol and diluted with water prior to SBSE. Dilution of the methanol extract before SBSE was optimized to obtain high sensitivity and to minimize adsorption onto the glass wall of the extraction vessel as well as to minimize sample matrix effects (particularly for the pesticides with high log K(o,w) values). The optimized method consists of a dual SBSE extraction performed simultaneously on respectively a twofold and a fivefold diluted methanol extract. After extraction, the two stir bars are placed in a single glass thermal desorption liner and are simultaneously desorbed. The method showed good linearity (r2 > 0.9900) and high sensitivity (limit of detection: < 5 microg kg(-1)) for most of the target pesticides. The method was applied to the determination of pesticides at low microg kg(-1) in tomato, cucumber, green soybeans, spinach, grapes, and green tea.