An Air‐breathing Carbon Cloth‐based Screen‐printed Electrode for Applications in Enzymatic Biofuel Cells

We report a prototype air‐breathing carbon cloth‐based electrode that was fabricated starting from a commercially available screen‐printed electrode equipped with a transparent ITO working electrode (DropSens, ref. ITO10). The fabrication of the air‐breathing electrodes is straightforward, shows satisfactory reproducibility and a good electrochemical response as evaluated by means of [Fe(CN)₆]^3?/4? voltammetry. The gas‐diffusion electrodes were successfully modified with the O₂ reducing enzyme bilirubin oxidase from Myrothecium verrucaria in a direct electron transfer regime. The enzyme modified electrodes showed a remarkable high current density for O₂ reduction in passive air‐breathing mode of up to 5 mA cm^?2. Moreover, the enzyme modified electrodes were applied as O₂ reducing biocathodes in a glucose/air enzymatic biofuel cell in combination with a high current density glucose oxidase/redox polymer bioanode. The biofuel cell provides a high maximum power density of (0.34±0.02) mW cm^?2 at 0.25 V. The straightforward design, low cost and the high reproducibility of these electrodes are considered as basis for standardized measurements under gas‐breathing conditions and for high throughput screening of gas converting (bio‐)catalysts.     

Carnation‐like CuO Hierarchical Nanostructures Assembled by Porous Nanosheets for Nonenzymatic Glucose Sensing

Carnation‐like CuO hierarchical nanostructures assembled by ultrathin porous nanosheets were successfully fabricated via a facile solvothermal route followed with heat treatment. As‐prepared CuO nanostructures exhibited excellent catalytic activity toward glucose oxidation in the absence of any enzymes. Under the optimized conditions, the CuO‐based enzymeless glucose sensor showed high sensitivity of 3.15 mA mM^?1 cm^?2, low limit of detection (98 nM, S/N=3), good reproducibility, excellent selectivity and long‐time stability. The superb nonenzymatic glucose sensing performance of the CuO hierarchical nanostructures was attributed to the highly catalytically active sites at the edges and basal planes of the CuO nanosheets, facile transportation of analytes through the abundant mesopores and macropores, robust and stable hierarchical structure. Moreover, the CuO‐based enzymeless glucose sensor showed high accuracy and reliability in comparison with clinical glucometer for quantitative determination of glucose in human blood serum samples.     

Carbon Nanostructured Screen‐printed Electrodes Modified with CuO/Glucose Oxidase/Maltase/SiO2 Composite Film for Maltose Determination

A sensitive voltammetric method was developed to determine maltose in beverage products using a carbon nanostructured screen‐printed electrode modified with CuO/glucose oxidase/maltase/SiO₂ biocomposite film. Adding CuO particles was done to possess catalytic activity toward hydrogen peroxide. Electrode modified by glucose oxidase and maltase shows a good response to maltose. A well‐defined reduction peak was registered at the potential of ?0.55 V (vs. Ag/AgCl) which intensity increases linearly with the concentration of maltose ranging from 0.01 to 0.1 mmol L^?1. The calculated limit of detection was 0.005 mmol L^?1. Tested on the beer samples, the developed CuO/glucose oxidase/maltase/SiO₂ biocomposite film covered carbon nanostructured screen‐printed electrode is showed to be a prospective sensitive element of the third generation biosensor for maltose.     

A Glucose Biosensor Based on Immobilization of Glucose Oxidase into 3D Macroporous TiO2

3D macroporous TiO₂ inverse opals have been derived from a sol‐gel procedure using polystyrene colloidal crystals as templates. EDS and SEM showed a face‐centered cubic (FCC) structure TiO₂ inverse opal was obtained. Glucose oxidase (GOx) was successfully immobilized on the surface of indium‐tin oxide (ITO) electrode modified by TiO₂ inverse opal (TiO_2(IO)). Electrochemical properties of GOx/TiO_2(IO)/ITO electrode were characterized by using the three electrodes system. The result of cyclic voltammetry showed that a couple of stable and well‐defined redox peaks for the direct electron transfer of GOx in absence of glucose, and the redox peak height enhanced in presence of 0.1 μM glucose. Compare with the ordinary structured GOx/TiO₂/ITO electrode, inverse opal structured GOx/TiO_2(IO)/ITO electrode has a better respond to the glucose concentration change. Under optimized experimental conditions of solution pH 6.8 and detection potential at 0.30 V versus saturated calomel electrode (SCE), amperometric measurements were performed. The sensitivity and the detection limit of glucose detection was 151 μA cm^?2 mM^?1 and 0.02 μM at a signal‐to‐noise ratio of 3, respectively. The good response was due to the good biocompatibility of TiO₂ and the large effective surface of the three‐dimensionally ordered macroporous structure.     

Electrochemical Monitoring of Methotrexate Anticancer Drug in Human Blood Serum by Using in situ Solvothermal Synthesized Fe3O4/ITO Electrode

Here, we reported on a one‐step fabrication of magnetite Fe₃O₄ nanoparticles/indium tin oxide (ITO) electrode based on the direct growing of Fe₃O₄ nanoparticles on the ITO surface by using a solvothermal process. The modified electrode was used as electrochemical methotrexate (MTX) biosensor with high sensitivity based on cyclic voltammetry and square wave voltammetry techniques. The results demonstrated a linear relationship between the MTX concentration and its oxidation current peak over a wide range from 10^?5 to 10^?14 mole/L with a limit of detection of 0.4×10^?15 M based on the square wave voltammetry (SWV) technique. In addition, Fe₃O₄/ITO electrode showed a good capability for measuring very low concentrations of MTX drug dissolved in human serum solution. Also, Fe₃O₄/ITO electrode was used for detecting MTX in blood serum samples collected from patients after their treatment with MTX. The prepared electrode showed the higher sensitivity that higher than the Viva‐E instrument, which opens the door for developing a cheap, simple and higher sensitive MTX sensor.     

Facile Synthesis of Leaf‐Like CuO Nanoparticles and Their Application on Glucose Biosensor

An efficient amperometric biosensor based on well‐crystallized leaf‐like CuO nanoparticles for detecting glucose has been proposed. The leaf‐like CuO nanoparticles, synthesized by a simple one‐step hydrothermal method, were characterized by X‐ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscopy (TEM) for the morphology study. Under the optimal condition, the electrochemical behaviour of the leaf‐like CuO nanoparticles modified electrode for detection of glucose exhibited high sensitivity of 246 µA/mM/cm², short response time (within 5 s), linear dynamic range from 1.0 to 170 µM (R²=0.9995), and low limit of detection (LOD) (S/N=3) of 0.91 µM. The high sensitivity, good reproducibility, stability, and fast amperometric sensing towards oxidation of glucose, make this biosensor promising for future application.     

Supramolecular Assembly of β‐Cyclodextrin‐Capped Gold Nanoparticles on Ferrocene‐Functionalized ITO Surface for Enhanced Voltammetric Analysis of Ascorbic Acid

A supramolecular recognition functionalized electrode (βCD‐nanoAu/Fc‐ITO) which exhibits redox‐activity was prepared through supramolecular assembly of β‐cyclodextrin (βCD) capped gold nanoparticles (βCD‐nanoAu) on the ITO previously coated with a monolayer of ferrocene residues (Fc‐ITO). The immobilization of βCD‐nanoAu on Fc‐ITO was confirmed by atomic force microscopy (AFM), and the supramolecular nature of the immobilization approach was also confirmed by cyclic voltammetry. On the other hand, the electrocatalytic activity of βCD‐nanoAu/Fc‐ITO electrode was also studied. The electrocatalytic activity toward ascorbic acid (AA) was enhanced compared with that at the Fc‐ITO electrode, and a linear relationship existed between the anodic peak and the concentration of AA in the range of 5.3×10^?5 to 3.0×10^?3 M with a detection limit (S/N=3) of 4.1×10^?6 M.     

Electrocatalysis of Horseradish Peroxidase Immobilized on Cobalt Nanoparticles Modified ITO Electrode

Abstract

It is the first time that Horseradish peroxidase (HRP) was successively immobilized on the magnetic cobalt nanoparticles modified ITO (indium tin oxide) electrode. Morphologies of electrode surface were featured by the field emission‐scanning electron microscope (FSEM). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to characterize the modified process of electrode. Direct electrochemistry and electrocatalysis of HRP immobilized on nano‐Co/ITO were investigated. The biosensor exhibited high sensitivity, good stability, and excellent electrocatalytic activity to the reduction of H₂O₂. Under the optimized experimental conditions, a calibration curve over 2.0×10^?9～2.0×10^?8 mol l^?1 and 2.0×10^?7～2.0×10^?6 mol l^?1, with a limit of detection of 1.9×10^?9 mol l^?1 was obtained. The apparent Michaelis‐Menten constant (K _M ^app ) for HRP/nano‐Co/ITO electrode was calculated to be 0.79 mmol l^?1, indicating a higher affinity of HRP attached on the modified electrode.     

Electrochemical Study of Chitosan‐SiO2‐MWNT Composite Electrodes for the Fabrication of Cholesterol Biosensors

We report a novel composite electrode made of chitosan‐SiO₂‐multiwall carbon nanotube (CHIT‐SiO₂‐MWNT) composite coated on the indium‐tin oxide (ITO) glass substrate. Cholesterol oxidase (ChOx) was covalently immobilized on the CHIT‐SiO₂‐MWNT/ITO electrode that resulted in a ChOx/CHIT‐SiO₂‐MWNT/ITO cholesterolactive bioelectrode. The CHIT‐SiO₂‐MWNT/ITO and ChOx/CHIT‐SiO₂‐MWNT/ITO electrodes were characterized with Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The influence of various parameters was investigated, including the applied potential, pH of the medium, and the concentration of the enzyme on the performance of the biosensor. The cholesterol bioelectrode exhibited a sensitivity of 3.4 nA/ mgdL^?1 with a response time of five seconds. The biosensor using ChOx/CHIT‐SiO₂‐MWNT/ITO as the working electrode retained its original response after being stored for six months. The biosensor using ChOx/CHIT‐SiO₂‐MWNT/ITO as the working electrode showed a linear current response to the cholesterol concentration in the range of 50–650 mg/dL.     

Nonenzymatic Electrochemical Glucose Sensor Based on Novel Copper Film

Novel copper (Cu) film composed of pillar‐like structure was synthesized on indium‐doped tin oxide (ITO) substrate by electrodeposition in acetate bath with proline as additive for the first time and used to construct nonenzymatic glucose sensor. When applied to detect glucose, such prepared electrode showed low operating potential (0.4 V), high sensitivity (699.4499 µA mM⁻¹ cm⁻²), and fast response time (<3 s) compared with other Cu‐based electrodes. In addition, the prepared electrode also offered good anti‐interference ability to ascorbic acid, uric acid and acetaminophen. Present study provides new insights into the control of Cu film morphology for sensor fabrication.     

A Novel NH2/ITO Ion Implantation Electrode: Preparation,Characterization, and Application in Bioelectrochemistry

A novel NH₂⁺ ion implantation‐modified indium tin oxide (NH₂/ITO) electrode was prepared. Acid‐pretreated, negatively charged MWNTs were firstly modified on the surface of NH₂⁺ ion implantation electrode, then, positively charged Mb was adsorbed onto MWNTs films by electrostatic interaction. The assembly of MWNTs and Mb was characterized with electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The immobilized Mb showed a couple of quasireversible cyclic voltammetry peaks in pH 7.0 phosphate buffer solution (PBS). The apparent surface concentration of Mb at the electrode surface was 1.06×10^?9 mol cm^?2. The Mb/MWNTs/NH₂/ITO electrode also gave an improved electrocatalytic activity towards the reduction of hydrogen peroxide. The catalysis currents increased linearly to the H₂O₂ concentration in a wide range from 9×10^?7 to 9.2×10^?5 M with a correlation coefficient of 0.999. The detection limit was 9.0×10^?7 M. The experiment results demonstrated that the modified electrode provided a biocompatible microenvironment for protein and supplied a necessary pathway for its direct electron transfer.     

Direct electrochemistry and electrocatalysis of hemoglobin on a gold ion implantation-modified indium tin oxide electrode

In this paper, a gold nanoparticle-modified indium tin oxide electrode (Au/ITO) was prepared without the use of any cross-linker or stabilizer reagent. The prepared Au/ITO was used as a new platform to achieve the direct electron transfer between Hb and the modified electrode. The proposed electrode exhibited a pair of well-defined redox peaks with a formal potential of ?0.073 V (vs. Ag/AgCl). The immobilized Hb showed excellent electrocatalytic activity toward H₂O₂ and the electrocatalytic current values were linear with the increasing concentration of H₂O₂ ranging from 1.0?×?10^?6?M to 7.0?×?10^?4?M. The detection limit was 2.0?×?10^?7?M (S/N?=?3) and the Michaelis–Menten constant was calculated to be 0.2 mM. The proposed electrode also showed high selectivity, long-term stability, and good reproducibility.     

CuO‐Doped Mesoporous Silica Hybrid for Rapid and Sensitive Amperometric Detection of Phenolic Compounds

This work constructed an amperometric biosensing platform using CuO doped mesoporous silica hybrid (CuO/SBA‐15) as a carrier. The CuO/SBA‐15 showed a pair of redox peaks of Cu^2+/0. Upon immobilization of tyrosinase on the hybrid, the resulting biosensor exhibited a rapid (<0.5 s) and sensitive amperometric response to phenolic compounds under the optimized conditions. The linear response to catechol ranged from 1.2×10^?9 to 3.0×10^?5 M. The activation energy for enzymatic reaction was calculated to be 26.6 kJ mol^?1. The apparent Michaelis–Menten constants of the enzyme electrode were estimated to be 54.6, 145, 17.0, 74.8 and 633 µM for catechol, phenol, p‐cresol, m‐cresol and dopamine hydrochloride, respectively. The metal oxide doped mesoporous silica hybrid exhibited excellent performance for construction of new biosensors.     

Electrochemical Synthesis of Shape-controlled Cu−Ni Nanocomposite and its Application for Nonenzymatic Glucose Sensing at Nanomolar Level

The electrodeposition method was firstly applied to obtain uniform cube-shaped copper nanoparticles on conductive glass (ITO), and then a layer of tiny nickel nanoparticles. A bimetallic composite electrode (Cu−Ni/ITO), characterized by TEM, XPS and XRD, was prepared to construct the non-enzyme electrochemical glucose sensor with high catalytic activity. The catalytic performance of Cu−Ni/ITO had been greatly improved, probably due to the synergistic bimetallic catalysis effect. The electrode had a satisfactory linear response in the range of 2.5×10⁻⁷ M to 2.6×10⁻³ M, with detection limit as low as 67 nM. Besides, Cu−Ni/ITO had good anti-interference ability and reproducibility, indicating the promising application for glucose detection in practical samples.     

Nanostructured Iron Oxide Platform for Impedimetric Cholesterol Detection

A nanostructured iron oxide (NanoFe₃O₄, particle size ca. 25 nm and roughness ca. 21 nm) film deposited onto a hydrolyzed indium‐tin‐oxide (ITO) coated glass plate has been used to immobilize cholesterol oxidase (ChOx) to fabricate an impedimetric cholesterol sensor. Electrochemical studies reveal that surface charged Fe₃O₄ nanoparticles provide better conformation for ChOx loading resulting in enhanced electron transfer between ChOx and the electrode. Impedimetric response studies of the ChOx/NanoFe₃O₄/ITO bioelectrode exhibit improved linearity (2.5–400 mg/dL), low detection limit (0.25 mg/dL), fast response time (25 s), high sensitivity (86 Ω/mg dL^?1/cm^?2) and a low value of the Michaelis‐Menten constant (K_m, 0.8 mg/dL) with a regression coefficient of 0.997.     

Nonenzymatic glucose sensor based on CuO microfibers composed of CuO nanoparticles

Fluorine tin oxide (FTO) electrode modified by copper oxide microfibers (CuO-MFs) composed of numerous interconnected CuO nanoparticles (CuO-NPs) for nonenzymatic glucose sensor was prepared by electrospinning precursor containing high percentage content of copper nitrate with subsequent calcination. The results of scanning electron microscope (SEM) showed the size of CuO particles composing CuO-MFs depended on the percentage content of copper nitrate in precursor solution. With increasing the percentage content of copper nitrate, the interconnected CuO-NPs would gradually replace the large-size CuO particles to accumulate the CuO-MFs, which have the potential to provide larger surface area and more reaction sites for electrocatalytic activity toward glucose. As a glucose sensor, the CuO-MFs modified FTO electrode prepared by 40 wt.% of copper nitrate exhibited a high sensitivity of 2321 μA mM⁻¹ cm⁻² with a low detection limit of 2.2 nM (signal/noise ratio (S/N) = 3). Additionally, the application of the CuO-MFs modified FTO electrode as a glucose sensor for biological samples was demonstrated with satisfactory results.     

Potential of Gelatin‐Zinc Oxide Nanocomposite as Ascorbic Acid Sensor

We report on the studies relating to fabrication of gelatin B (GB) and zinc oxide (ZnO) based nanocomposite (GB‐ZnO) film deposited on indium‐tin‐oxide (ITO) glass plate, and used for the immobilization of ascorbate oxidase (AsOx) which was further used for ascorbic acid (AA) detection. The structural and morphological studies of GB‐ZnO, and AsOx/GB‐ZnO/ITO bioelectrodes were carried out using XRD, SEM and FTIR techniques. This bioelectrode showed a broad range of linearity (5–500 mg/dL), low detection limit (1 mg/dL), higher sensitivity (0.106 µA mg/dLcm^?2) and low value of the apparent Michaelis? Menten constant (K_m^app=0.35 mg/dL) for AA. Efforts are being made to utilize this electrode for sensing AA in real samples in a bid to develop a strip based sensor.     

Electrocatalytic Oxidation of Glucose at Carbon Nanotubes Supported PtRu Nanoparticles and Its Detection

PtRu nanoparticles were supported on multiwall carbon nanotubes (MWNTs), which were further fabricated as an electrode for nonenzymatic glucose sensing. Transmission electron microscope and X‐ray diffraction patterns were used for characterization of the PtRu nanoparticles on MWNTs. Cyclic voltammetry and chronopotentiometry were applied to investigate the performance of the PtRu/MWNTs nanocomposite electrode for nonenzymatic oxidation of glucose. The PtRu/MWNTs electrode shows high electrocatalytic activity towards the oxidation of glucose in 0.1 M NaOH solution and thus can be used to selectively detect glucose. Under the optimal potential (+0.55 V vs. Ag/AgCl), the biosensor effectively performs a selective electrochemical analysis of glucose in the presence of common interferents, such as ascorbic acid (AA), dopamine (DP) and uric acid (UA). Wide linear calibration ranging from 1 mM to 15 mM, high sensitivity of 28.26 μA cm^?2 mM^?1, low detection limit of 2.5×10^?5 M, and fast response time of 10 s were achieved for the detection of glucose at the PtRu/MWNTs electrode.     

Study of ITO Glass Electrode Modified with Iron Oxide Nanoparticles and Nafion for Glucose Biosensor Application

In this study, we report the fabrication of the indium tin oxide (ITO) glass electrode modified with iron oxide nanoparticles (IONPs) and nafion for glucose biosensor applications. The IONPs was synthesized using the precipitation method and functionalized with citric acid (CA) to provide hydrophilic surface and functional group for glucose oxidase (GOx) enzyme immobilization. The structural and morphological studies of CA-IONPs were characterized using X-ray diffractometer (XRD) and transmission electron microscope (TEM). The size of the IONPs measured from TEM image was ∼17 nm. The bioelectrode designated as Nafion/GOx/CA-IONPs/ITO was developed by drop casting of the CA-IONPs, GOx and nafion on the ITO glass. The Nafion/GOx/CA-IONPs/ITO bioelectrode showed good electrochemical performance for glucose detection. The functionalized CA-IONPs acted as the catalyst and help to improve the electron transfer rate between GOx and ITO electrode. In addition, thin nafion film was coated on the electrode to prevent interference and improve chemical stability. The Nafion/GOx/CA-IONPs/ITO bioelectrode showed high sensitivity of 70.1 μAmM^-1cm^-2 for the linear range of 1.0-8.0 mM glucose concentrations.