Self‐Assembled Prussian Blue Nanoparticles Based Electrochemical Sensor for High Sensitive Determination of H2O2 in Acidic Media

In this paper, self‐assembled Prussian blue nanoparticles (PBNPs) on carbon ceramic electrode (CCE) were developed as a high sensitive hydrogen peroxide (H₂O₂) electrochemical sensor. The PBNPs film was prepared by a simple dipping method. The morphology of the PBNPs‐modified CCE was characterized by scanning electron microscopy (SEM). The self‐assembled PB film exhibited sufficient mechanical, electrochemical stability and high sensitivity in compare with other PB based H₂O₂ sensors. The sensor showed a good linear response for H₂O₂ over the concentration range 1 μM–0.26 mM with a detection limit of ca. 0.7 μM (S/N=3), and sensitivity of 754.6 mA M^?1 cm^?2. This work demonstrates the feasibility of self‐assembled PBNPs‐modified CCE for practical sensing applications.     

Low‐Potential Sensitive Hydrogen Peroxide Detection Based on Nanotubular TiO2 and Platinum Composite Electrode

In this work, a novel sensor for detecting hydrogen peroxide was constructed on the base of nanotubular TiO₂ and platinum nanoparticles. The morphology, structural, and electrochemical properties of the Pt/TiO₂ nanocomposite electrodes were characterized by SEM, XRD and electrochemical methods. With an operating potential of +0.3 V versus Ag/AgCl, the sensor produces catalytic oxidation currents at the nanocomposite electrode, which can be exploited for quantitative determinations. The amperometric signals are linearly proportional to hydrogen peroxide concentration in the range 4×10^?6 to 1.25×10^?3 M. The regression equation is I (μA)=0.85 c (mM)+0.16 with a correction coefficient of 0.997. At a signal‐to‐noise ratio of 3, a detection limit of 4.0 μM H₂O₂ can be observed for the nanocomposite electrode. In addition, the sensor has a good stability and reproducibility. The construction process is simple and inexpensive. The results demonstrated that nanotubular TiO₂ exhibits great prospect for developing a class of ideal and novel bioreactors and biosensors.     

The Hybrid of Gold Nanoparticles and 3D Flower‐like MnO2 Nanostructure with Enhanced Activity for Detection of Hydrogen Peroxide

3D Flower‐like manganese dioxide (MnO₂) nanostructure with the ability of catalysis for hydrogen peroxide (H₂O₂) and super large area that can support gold nanoparticles (AuNPs) with enhanced activity of electron transfer have been developed. The nanostructure of hybrids was prepared by directly mixing citric‐capped AuNPs and 3‐aminopropyltriethoxysilane (3‐APTES)‐capped nano‐MnO₂ using an electrostatic adsorption strategy. The Au‐MnO₂ composite was extensively characterized by scanning electron microscope (SEM), X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), the Brunauer‐Emmett‐Teller (BET) method and X‐ray photoemission spectroscopy (XPS). Electrochemical properties were evaluated through cyclic voltammetry (CV) and amperometric method. The prepared sensor showed excellent electrochemical properties towards H₂O₂ with a wide linear range from 2.5×10⁻³∼1.39 mM and 3.89∼13.89 mM. The detection limit is 0.34 μM (S/N=3) with the sensitivities of 169.43 μA mM⁻¹ cm⁻² and 55.72 μA mM⁻¹ cm⁻². The detection of real samples was also studied. The result exhibited that the prepared sensor can be used for H₂O₂ detection in real samples.     

Electrode modified with a composite film of ZnO nanorods and Ag nanoparticles as a sensor for hydrogen peroxide

A conducting fluorine-doped tin oxide (FTO) electrode, first modified with zinc oxide nanorods (ZnONRs) and subsequently attached with photosynthesized silver nanoparticles (AgNPs), designated as AgNPs/ZnONRs/FTO electrode, was used as an amperometric sensor for the determination of hydrogen peroxide. The first layer (ZnONRs) was obtained by chemical bath deposition (CBD), and was utilized simultaneously as the catalyst for the photoreduction of Ag ions under UV irradiation and as the matrix for the immobilization of AgNPs. The aspect ratio of ZnONRs to be deposited was optimized by controlling the number of their CBDs to render enough surface area for Ag deposition, and the amount of AgNPs to be attached was controlled by adjusting the UV-irradiation time. The immobilized AgNPs showed excellent electrocatalytic response to the reduction of hydrogen peroxide. The resultant amperometric sensor showed 10-fold enhanced sensitivity for the detection of H₂O₂, compared to that without AgNPs, i.e., only with a layer of ZnONRs. Amperometric determination of H₂O₂ at −0.55 V gave a limit of detection of 0.9 μM (S/N = 3) and a sensitivity of 152.1 mA M⁻¹ cm⁻² up to 0.983 mM, with a response time (steady-state, t₉₅) of 30-40 s. The selectivity of the sensor was investigated against ascorbic acid (AA) and uric acid (UA). Energy dispersive X-ray (EDX) analysis, transmission electron microscopic (TEM) image, X-ray diffraction (XRD) patterns, cyclic voltammetry (CV), and scanning electron microscopic (SEM) images were utilized to characterize the modified electrode. Sensing properties of the modified electrode were studied both by CV and amperometric analysis.     

Synthesis of PtxSn/MWCNTs and their Application in Non‐enzymatic Glucose and Hydrogen Peroxide Sensors

Pt_xSn/MWCNTs (x=1, 2, 3) nanocomposites were synthesized by chemical reduction. Comparing all of the materials, the results revealed that the best material was Pt₃Sn/MWCNTs. The sensor based on Pt₃Sn/MWCNTs exhibited excellent catalytic activities towards glucose and hydrogen peroxide. Sensing of glucose had a double‐linear range: one was between 50 μM and 550 μM, the other was between 1.35 mM and 16.35 mM. These were due to the fact that more and more intermediate species were adsorbed onto the electrode surface with increasing concentration of glucose, which limited the following glucose oxidation. Meanwhile, the sensor also had a linear response range between 0.05 mM and 18.95 mM for hydrogen peroxide. Furthermore, the glucose and hydrogen peroxide sensors exhibited excellent selectivity, stability, and reproducibility. Thus the sensors had potential utilities in the detection of glucose and hydrogen peroxide.     

Template-assisted synthesis of rough Ag nanorods and their application for amperometric sensing of H2O2

Silver nanorods (Ag NRs) with rough sidewalls were successfully obtained via extremely simple template-assisted electrochemical deposition followed by selective dealloying. Ag–Zn NRs with an average diameter of ∼250 nm and the atomic ratio of about 1:1 were synthesized inside the nanochannels of a polycarbonate membrane. A chemical etching of Zn in a sulfuric acid solution led to the formation of NRs with smaller diameters, rough sidewalls, and much lower Zn content. Such kind of a material exhibited quite promising electrocatalytic properties toward reduction of hydrogen peroxide and can be used as an amperometric sensor for the detection and determination of H₂O₂.     

Application of Copper Electrode Based Amperometric Detector Cell for LC Analysis of Main Sugar Component of Honey and Nectar

A method for quantification of the main sugar components of honey and nectars are worked out and investigated. The method employs IC separation on CarboPac PA1 column with sodium hydroxide eluent and home made, electrochemical detector cells that contain copper working electrode. The detector cells operate in amperometric mode. The electrochemical oxidation of the sugar components was studied, estimating the number of electrons exchanged, the rate constant of the electrode reaction. The electrode processes showed electrocatalytic character with formate ions as main product of oxidation. Real samples of honey and nectar taken from different plants were analyzed with the method proposed.     

Direct Electrochemistry of Hemoglobin Immobilized on Carbon‐Coated Iron Nanoparticles for Amperometric Detection of Hydrogen Peroxide

A novel method for preparation of hydrogen peroxide biosensor was presented based on immobilization of hemoglobin (Hb) on carbon‐coated iron nanoparticles (CIN). CIN was firstly dispersed in a chitosan solution and cast onto a glassy carbon electrode to form a CIN/chitosan composite film modified electrode. Hb was then immobilized onto the composite film with the cross‐linking of glutaraldehyde. The immobilized Hb displayed a pair of stable and quasireversible redox peaks and excellent electrocatalytic reduction of hydrogen peroxide (H₂O₂), which leading to an unmediated biosensor for H₂O₂. The electrocatalytic response exhibited a linear dependence on H₂O₂ concentration in a wide range from 3.1 μM to 4.0 mM with a detection limit of 1.2 μM (S/N=3). The designed biosensor exhibited acceptable stability, long‐term life and good reproducibility.     

Electrocatalytic Behavior and Amperometric Detection of Morphine on ITO Electrode Modified with Directly Electrodeposited Gold Nanoparticles

A gold nanoparticles (AuNPs) modified indium tin oxide (ITO) film coated glass electrode was prepared via a novel electrochemical deposition technique. The UV‐visible spectrum and SEM indicated that the AuNPs on ITO electrode surface were spherical shape and quite symmetric distributed. The modified electrode exhibited excellent catalytic activity for the oxidation of morphine (MO). At optimal experimental condition, the oxidation current was responsive with the MO concentrations ranging from 8.0×10^?7 to 1.6×10^?5 M, the detection limit was 2.1×10 ^–7 M. The modified electrode also exhibited high stability and reproducibility. The average recoveries of detection MO in human urine were ranged between 91.95% and 92.23%, and the RSD was less than 3.68% (n=5).     

The Rapid and Practical Route to Cu@PCR Sensor: Modification of Copper Nanoparticles Upon Conducting Polymer for a Sensitive Non-Enzymatic Glucose Sensor

In this work, rapid, sensitive, practical, and economical strategy for non-enzymatic glucose sensor has been reported based on a modification of copper nanoparticles upon conducting polymer with high surface area (Cu@PCR). Firstly, PCR conducting polymer electrode (PCR) has been successfully fabricated by electrochemical polymerization of a specially synthesized and characterized star-shaped carbazole derivative. Then copper nanoparticles have been successfully electrodeposited on the PCR as a practical method with cyclic voltammetry. The morphologies of the synthesized materials have been characterized by scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) measurements. The Cu@PCR sensor platform has been displayed a synergistic effect of high catalytical properties of copper nanoparticles and high electroactive properties of PCR towards the glucose oxidation in alkaline medium. The Cu@PCR sensor platform has shown high sensitivity of 847 μAmM⁻¹cm⁻², good stability (10 weeks), a low detection limit of 0.043 μM, and a fast response of 3 s for the non-enzymatic electrochemical detection of glucose. This organic−inorganic hybrid composite sensor is a promising candidate for the fabrication of a highly sensitive and rapid glucose-sensing with the simple preparation procedure and use of a low-cost precursor.     

Fabrication and Application of a Sensitive and Highly Stable Copper Hexacyanoferrate Modified Carbon Ionic Liquid Paste Electrode for Hydrogen Peroxide and Glucose Detection

A three‐factor mixture design and response surface methodology were employed to find the optimal weight ratio of graphite powder, n‐dodecylpyridinium hexafluorophosphate and paraffin for the fabrication of a copper hexacyanoferrate modified carbon ionic liquid paste electrode (CuHCFe‐CILPE). The fabricated sensor showed electrocatalytic activity towards oxidation and reduction of hydrogen peroxide. It also was observed that the electrocatalytic activity for hydrogen peroxide oxidation was much higher than the electrocatalytic activity for hydrogen peroxide reduction. Glucose oxidase was then successfully immobilized on the surface of the proposed sensor to examine the possibility of using CuHCFe‐CILPE for the biosensor fabrication.     

Renewable Surface Sol‐gel Derived Carbon Ceramic Electrode Modified with Copper Complex and Its Application as an Amperometric Sensor for Bromate Detection

A sol‐gel technique was used for the preparation of a three dimensional carbon composite electrode modified with [Cu(bpy)₂]Br₂ complex. A reversible redox couple of Cu(II)/Cu(I) is observed at the electrode surface. The electrochemical behavior and stability of the modified electrode was characterized by cyclic voltammetry. The charge transfer coefficient (α) and charge transfer rate constant (K_s) for the modified electrode were determined by cyclic voltammetry, which were found to be 0.46 and 14.2 s^?1, respectively. The modified electrode showed excellent catalytic activity toward bromate reduction at significantly reduced overpotentials and can be used successfully for amperometric detection of bromate. Under the optimized conditions, the calibration plots are linear in the concentration range 0.5 μM ?200μM. Detection limit (signal to noise is 3) and sensitivity were found to be 0.1 μM and 20 nA / μM, respectively. These analytical parameters compare favorably with those obtained with modern analytical techniques. The modified carbon ceramic electrode doped with Cu‐Complex shows a good reproducibility, a short response time (t<2 s), remarkable long term stability (>4 months) and especially good surface renewability by simple mechanical polishing (RSD for 6 successive polishing is 1.5%).     

An Enzyme‐free H2O2 Sensor Based on Poly(2‐Aminophenylbenzimidazole)/Gold Nanoparticles Coated Pencil Graphite Electrode

A poly(2‐aminophenylbenzimidazole)/gold nanoparticles (P2AB/AuNPs) coated disposable pencil graphite electrode (PGE) was fabricated as an enzyme‐free sensor for the H₂O₂ determination. P2AB/AuNPs and P2AB were successfully synthesized electrochemically on PGE in acetonitrile for the first time. The coatings were characterized by scanning electron microscopy, X‐ray diffraction spectroscopy, Energy‐dispersive X‐ray spectroscopy, Surface‐enhanced Raman spectroscopy, and UV‐Vis spectroscopy. AuNPs interacted with P2AB as carrier enhances the electrocatalytic activity towards reduction of H₂O₂. The analytical performance was evaluated in a 100 mM phosphate buffer solution at pH 6.5 by amperometry. The steady state current vs. H₂O₂ concentration is linear in the range of 0.06 to 100 mM (R²=0.992) with a limit of detection 3.67×10^?5 M at ?0.8 V vs. SCE and no interference is caused by ascorbic acid, dopamine, uric acid, and glucose. The examination for the sensitive determination of H₂O₂ was conducted in commercially available hair oxidant solution. The results demonstrate that P2AB/AuNPs/PGE has potential applications as a sensing material for quantitative determination of H₂O₂.     

基于纳米银的比色阵列传感器的构建及在蛋白质检测中的应用

蛋白质的快速高效检测和鉴定在医学诊断、不同疾病的治疗和蛋白质组学中具有巨大的前景。目前的检测手段大多存在一些问题,如操作繁琐、效率低等,因此开发一个理想的蛋白质检测方法尤为重要。以纳米银(AgNPs)为传感元件的阵列传感器在蛋白质检测方面具有操作便捷、准确率高、可视化等优点。本文合成两种不同颜色和形状的AgNPs:黄色球形和蓝色三角形,以此构建一个简单的比色阵列传感器,用于蛋白质的区分检测。该传感器可以准确地识别和区分不同种类的蛋白质,准确率为100%。在成功识别出不同类型的蛋白质的基础上,进一步评估了该阵列传感器应用于区分正常和变性蛋白质的能力,准确率为96.0%。此外,该阵列传感器对于未知样本的识别也具有高的准确率。     

Green Synthesis of Ag Nanoparticles by Callicarpa Maingayi: Characterization and Its Application with Graphene Oxide for Enzymeless Hydrogen Peroxide Detection

A facile green synthesis of silver nanoparticles (AgNPs) was achieved using aqueous leaf extract of Callicarpa Maingayi as a reducing and stabilizing agent during the synthesis from its salt solutions. The synthesized silver nanoparticles were analyzed with transmission electron microscopy (TEM), X‐ray diffraction (XRD) and energy dispersive spectrometer (EDS). XRD study shows that the particles are crystalline in nature with face centered cubic geometry. The crystallite size obtained from XRD is about 15 nm which is in agreement well with the TEM results. A new nanostructure sensor was constructed by immobilizing silver nanoparticles and graphene oxide (AgNPs‐GO) composite film on a glassy carbon electrode (AgNPs‐GO/GCE). It was found that the AgNPs‐GO composite exhibits good catalytic activity toward the reduction of hydrogen peroxide (H₂O₂), leading to an enzymeless sensor with a fast amperometric response time of less than 5 s, high selectivity, good reproducibility and stability. The linear range was 5.0 μM to 700 μM with a detection limit of 0.6 μM (S/N = 3).     

Application of a Square‐Wave Potential Program for Time‐Dependent Amperometric Detection in Capillary Electrophoresis

Use of a square‐wave potential program for time‐dependent amperometric detection of analyte zones in capillary electrophoresis (CE) is described. Electrochemical detection for CE requires that the separation field be isolated from that of the electrochemical detection. This is generally done by physically separating the CE separation field from that of the detection. By applying a time variant potential program to the detection electrode, the detector current has a time dependence that can be used to help isolate the electrochemical detection current from that of the separation. When using a 20 μm inner‐diameter capillary, we find that a square‐wave potential program decreases the RMS baseline current from 4.5×10^?10 A, found with a constant potential amperometric detection, to 1.1×10^?10 A when using a square‐wave potential program. With a 75 μm inner‐diameter capillary, the improvement is even more dramatic, from 2.3×10^?9 A with amperometric detection to 2.06×10^?10 A when using a 1 Hz square‐wave potential program. When not using the time‐dependent detection with the 75 μm capillary, the analyte zones were beneath the S/N for the system and not detected. With the square‐wave potential program and time‐dependent detection, however, the analyte zones for an electrokinetic injection of 200 μM solution of 2,3‐dihydroxybenzoic acid were observed with the 75 μm inner‐diameter capillary. The improvement in the ability to discriminate the analytical signal from the background found experimentally is consistent with modeling studies.     

Electrocatalytic Reduction of H2O2 and Oxygen on the Surface of Thionin Incorporated onto MWCNTs Modified Glassy Carbon Electrode: Application to Glucose Detection

A new H₂O₂ enzymeless sensor has been fabricated by incorporation of thionin onto multiwall carbon nanotubes (MWCNTs) modified glassy carbon electrode. First 50 μL of acetone solution containing dispersed MWCNTs was pipetted onto the surface of GC electrode, then, after solvent evaporations, the MWCNTs modified GC electrode was immersed into an aqueous solution of thionin (electroless deposition) for a short period of time <5–50 s. The adsorbed thin film of thionin was found to facilitate the reduction of hydrogen peroxide in the absence of peroxidase enzyme. Also the modified electrode shows excellent catalytic activity for oxygen reduction at reduced overpotential. The rotating modified electrode shows excellent analytical performance for amperometric determination of hydrogen peroxide, at reduced overpotentials. Typical calibration at ?0.3 V vs. reference electrode, Ag/AgCl/3 M KCl, shows a detection limit of 0.38 μM, a sensitivity of 11.5 nA/μM and a liner range from 20 μM to 3.0 mM of hydrogen peroxide. The glucose biosensor was fabricated by covering a thin film of sol–gel composite containing glucose oxides on the surface of thionin/MWCNTs modified GC electrode. The biosensor can be used successfully for selective detection of glucose based on the decreasing of cathodic peak current of oxygen. The detection limit, sensitivity and liner calibration rang were 1 μM, 18.3 μA/mM and 10 μM–6.0 mM, respectively. In addition biosensor can reach 90% of steady currents in about 3.0 s and interference effect of the electroactive existing species (ascorbic acid–uric acid and acetaminophen) is eliminated. The usefulness of biosensor for direct glucose quantification in human blood serum matrix is also discussed. This sensor can be used as an amperometric detector for monitoring oxidase based biosensors.     

Nanodiamond Decorated with Silver Nanoparticles as a Sensitive Film Modifier in a Jeweled Electrochemical Sensor: Application to Voltammetric Determination of Thioridazine

Nanodiamond? graphite (NDG) decorated with Ag nanoparticles (AgNPs‐NDG) was prepared and used to construct a novel sensitive sensor for the voltammetric determination of thioridazine (TR). The results indicate a remarkable increase in the oxidation peak currents together with a negative shift in the oxidation peak potentials, in comparison to the bare pyrolytic graphite electrode. Remarkable enhancement in microscopic area of the electrode along with strong adsorption of TR on the surface of the modified electrode resulted in a considerable increase in the peak current of TR. The surface morphology and the nature of the composite film deposited on PGE were characterized by scanning electron microscopy, atomic force microscopy, cyclic voltammetry and electrochemical impedance spectroscopy. Experimental variables, such as the deposited amount of the modifier suspension, pH of the supporting electrolyte, the accumulation potential and time are optimized by monitoring the CV responses of TR. Under the optimal conditions, the modified electrode showed a wide linear response to the concentration of TR in the range of 0.08–100 µM with a detection limit of 0.01 µM. The prepared modified electrode showed several advantages: simple preparation method, high stability and uniformity in the composite film, high sensitivity, long‐term stability and remarkable voltammetric reproducibility in response to TR. The modified electrode can be successfully applied for accurate determination of trace amounts of TR in pharmaceutical and clinical preparations.     

Amperometric Detection of H2O2 Using Gold Electrodes Modified with Starburst PAMAM Dendrimers and Prussian Blue

Gold‐bead electrodes were modified by covalent bonding or physical adsorption of several Starburst PAMAM dendrimers (generations 2.0, 3.0 and 4.0) followed by absorption of Prussian Blue (PB). The covalent dendrimer‐PB‐modified electrodes can be used as amperometric sensors of H₂O₂ in aqueous solution. They offer enhanced sensitivity with correspondingly lower detection and quantification limits compared to similar amperometric detectors.     

Gold Nanoparticles Decorated Graphene as a High Performance Sensor for Determination of Trace Hydrazine Levels in Water

Electrochemical sensors provide a selective, sensitive and an easy approach to detect hazardous substances such as hydrazine. Herein, we investigate a facile route for the fabrication of a nanostructured composite based on Au nanoparticles (AuNPs) decorated graphene and present its sensing performance towards hydrazine. Our strategy involves electrophoretic deposition (EPD) of graphene oxide (GO) on Au substrate to obtain a uniform layer EPD‐GO, followed by electrochemical reduction of GO to yield high quality graphene ERGO and electrodeposition of monodispersed AuNPs on ERGO (AuNPs/ERGO/Au). The modified AuNPs/ERGO/Au electrode was characterized using scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FT‐IR) techniques. The sensor exhibited an improved catalytic activity with a peak potential of +87 mV (vs. Ag/AgCl) for hydrazine oxidation. The high performance of this hybrid electrode is due to the presence of a synergistic effect between AuNPs and ERGO at their interface. Insights into the mechanism and kinetics of hydrazine oxidation are withdrawn from varying the voltage scan rate as the reaction is fully irreversible and diffusion‐controlled. The proposed hydrazine sensor showed suitability for nanomolar detection (detection limit of 74 nM), high selectivity in the presence of common ions and efficiency for application in water samples.