基于石墨烯的毒死蜱分子印迹电化学传感器的制备及对毒死蜱的测定

利用分子印迹技术,以马来松香丙烯酸乙二醇酯为交联剂,使用自由基热聚合法在石墨烯修饰的玻碳电极表面合成毒死蜱( CPF)分子印迹聚合膜,制得了CPF分子印迹电化学传感器。采用循环伏安法、线性扫描伏安法和电化学交流阻抗法等,考察了此CPF分子印迹膜的电化学性能。在最佳检测条件下,传感器的峰电流与CPF浓度在2.0×10-7~1.0×10-5mol/L范围内呈线性关系,线性方程为Ip(μA)=-7.1834-0.2424C (μmol/L),相关系数r2=0.9959,检出限为6.7×10-8 mol/L(S/N=3)。构建了CPF分子印迹电化学传感器的动力学吸附模型,测得印迹传感器的印迹因子β=2.59,结合速率常数k=12.2324 s。传感器表现出良好的重现性和稳定性,并成功用于实际水样和蔬菜样品中CPF的测定,加标回收率为94.1%~101.4%。     

基于分子印迹膜修饰丝网印刷电极的地西泮电化学传感器

以地西泮为模板分子,采用循环伏安法在一次性丝网印刷电极表面原位电聚合形成聚邻苯二胺膜,洗脱除去模板分子后得到地西泮分子印迹膜修饰丝网印刷电极。利用差示脉冲法对印迹膜和非印迹膜进行评价,表征了电极表面膜的电化学性质。以KI为印迹电极和底液间的探针,建立了一种间接检测地西泮的传感方法。该传感器的敏感元件为修饰有分子印迹膜的丝网印刷电极,其制备和更换非常方便。用于电化学检测时,样品的富集时间为3min,地西泮的浓度在2.0×10-7～1.0×10-5mol/L范围内与峰电流呈良好的线性关系,检出限为2.5×10-8mol/L,基于猪肉样品的加标回收率为92%～95%。将该传感器初步用于实际样品分析,结果满意。     

Molecularly Imprinted Poly-o-phenylenediamine Electrochemical Sensor for Entacapone

We have developed a molecularly imprinted polymer (MIP) electrochemical sensor for entacapone (ETC) based on an electropolymerised polyphenylenediamine (Po-PD) on a glassy carbon electrode (GCE) surface. The direct electropolymerisation of the o-phenylenediamine monomer (o-PD) was carried out with ETC as a template. The steps of electropolymerization process, template removal and binding of the analyte were tested by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) using [Fe(CN)₆]³⁻/[Fe(CN)₆]^{4 −} as a redox probe. The operation of the sensor has been investigated by differential pulse voltammetry (DPV). Under optimal experimental conditions, the response of the DPV was linearly proportional to the ETC concentration between 1.0×10⁻⁷ and 5.0×10⁻⁶ M ETC with a limit of detection (LOD) of 5.0×10⁻⁸ M. The developed sensor had excellent selectivity without detectable cross-reactivity for levodopa and carbidopa. The MIP sensor was successfully used to detect ETC in spiked human serum samples.     

Electrochemical Determination of Tetracycline Using Molecularly Imprinted Polymer Modified Carbon Nanotube‐Gold Nanoparticles Electrode

This paper reports the use of a tetracycline (TC) sensor constructed from a combination of molecularly imprinted polymer (MIP) and gold nanoparticles modified multiwall carbon nanotubes (MWNTs‐GNPs). The results demonstrated that the amount of recognition sites in the polymer was significantly increased and the electron transfer ability of the sensor was improved. The relationship between the peak current and the TC concentration was linear in the range from 0.1 to 40 mg L^?1, and the detection limit was 0.04 mg L^?1 (S/N=3). The peak current to TC was 4.3, 6.2 and 6.8 times larger than that of oxytetracycline, chloramphenicol and nafcillin, respectively. Thus, the combination of MIP and MWNTs‐GNPs provides a sensitive and selective electrochemical detection method for tetracycline.     

Determination of Bisphenol A Using an Electrochemical Sensor Based on a Molecularly Imprinted Polymer-Modified Multiwalled Carbon Nanotube Paste Electrode

A novel electrochemical sensor for bisphenol A was developed through the combination of a molecular imprinting technique with a multiwalled carbon nanotube paste electrode. A molecularly imprinted polymer and nonimprinted polymer were synthesized in the presence and absence of bisphenol A, and then used to prepare the electrode. The bisphenol A imprinted polymer was applied as a selective recognition element in the electrochemical sensor. Differential pulse voltammetry was used to characterize the electrochemical behavior of bisphenol A at the modified electrodes. The results showed that the imprinted sensor had highest response for bisphenol A. Parameters including the carbon paste composition, pH, and adsorption time for the imprinted sensor were optimized. Under the optimized conditions, the differential pulse voltammetry peak current was linear with the concentration of bisphenol A from 0.08 to 100.0 µM, with a detection limit of 0.022 µM. The imprinted sensor for bisphenol A exhibited good selectivity, stability, and reproducibility. This sensor was successfully used for the determination of bisphenol A in real water samples.     

Development and Characterization of an Electrochemical Sensor for Cinchonidine Detection Based on Molecularly Imprinted Polymer with Modified Rosin as Cross-linker

Molecularly imprinted polymers(MIPs) were applied as molecular recognition elements to an electrochemical sensor for cinchonidine(CD). A kind of MIP was synthesized with cinchonidine as template, modified rosin( ethylene glycol maleic rosinate acrylate) containing the skeleton of phenanthrene rings as cross-linker and methylacrylic acid as functional monomer. MIP membrane was prepared on a glassy carbon electrode for the determination of CD via free radical polymerization method. Electrochemical impedance spectroscopy(EIS) and cyclic voltammetry( CV) were used to characterize the membrane electrochemical behavior in electrode fabrication process. The experimental conditions were discussed. Under optimum conditions, it was found that the response of peak currents was linear to the concentration of CD in a range of 0.013―2.26 mmol/L. The detection limit for CD is 1 μmol/L, the relative standard deviation for 100 μmol/L CD is 1.34% and the incubation time is 2 min. The sensor was applied to the determination of CD in urine samples with satisfactory results.     

Electrochemical Sensor for trans‐Resveratrol Determination Based on Indium Tin Oxide Electrode Modified with Molecularly Imprinted Self‐Assembled Films

A voltammetric sensor for sensitive and specific determination of trans‐resveratrol (RES) were prepared based on immobilization of an RES‐imprinted film on the surface of functionalized Indium Tin Oxide (ITO) electrode, which was modified with γ‐methacyloxypropyl trimethoxysilane (γ‐MPS). Cyclic Voltammetry (CV) was presented to extract RES from the molecularly imprinted polymer film and RES were extracted rapidly and completely. The binding performance of the imprinted electrode with the template RES were investigated using differential pulse voltammetry (DPV). The results showed that the imprinted ITO film can give selective recognition to the template RES over that of structurally analogous molecules. A linear response to RES in the concentration range of 2.0×10^?6 M to 2.0×10^?5 M was observed with a correlation coefficient of 0.992, and the detection limit of the electrochemical sensor was 8.0×10^?7 M. Whereas, binding to the reference nonimprinted electrode, made in the same way but without the addition of template RES, there was almost no response to RES.     

分子印迹电位型传感器快速检测猪尿液中的克伦特罗

以盐酸克伦特罗为模板分子,采用沉淀聚合法合成了克伦特罗的分子印迹聚合物,并以其为离子载体,制得分子印迹聚合物膜克伦特罗离子选择性电极。在最优实验条件下,电极对克伦特罗阳离子的检出限可达7.0×10-8mol/L,线性范围为1.0×10-7～1.0×10-4mol/L,能斯特斜率为55.7 mV/decade。此电极具有优越的选择性、快速的响应时间以及良好的稳定性;已成功应用于实际猪尿样品中克伦特罗的测定,加标回收率为98%～107%,检测时间小于3 min。     

A Novel and Selective Methylene Blue Imprinted Polymer Modified Carbon Paste Electrode

In this study, methylene blue (MB) imprinted microbeads were synthesized and characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM).Differential pulse voltammetric responses of carbon paste electrodes modified with MB imprinted polymer were used to evaluate the adsorption and selectivity features of the polymer. For selectivity studies two basic dyestuffs (thionine blue and toluidine blue) which have similar structure to MB were chosen. Comparison of the voltammetric responses obtained with pure carbon paste and carbon paste modified with either imprinted or nonimprinted polymer electrodes revealed that MB imprinted polymer presented a higher selectivity to the template molecule MB in contrast to structurally similar molecules, thionine blue and toluidine blue.     

一种新型分子印迹聚合物基的化学发光阵列传感器

建立了一种分子印迹-化学发光阵列传感器测定甘氨酸的新方法. 该方法以甘氨酸为模板分子, 合成了分子印迹聚合物微球, 将该聚合物微球固定在96孔板上, 用它来识别丹磺酰氯标记的甘氨酸(Dns-Gly). 最后加入化学发光试剂(TCPO-H2O2-咪唑), 测量相对化学发光强度定量检测甘氨酸. 在最佳试验条件下, 相对化学发光强度和甘氨酸的浓度在0.2～60 μmol/L范围内成良好的线性关系, 相关系数为r＝0.9972, 方法的检出限为0.07 μmol/L, 对1 μmol/L甘氨酸溶液进行11次平行测定, 相对标准偏差为3.3% (n＝11). 由于以甘氨酸为模板分子合成出来的分子印迹聚合物空腔比较小, 避免了非特异性吸附, 使它在识别丹磺酰氯标记的甘氨酸时特异性、响应速度和灵敏度都有所增强.     

Modification of Carbon Paste Electrode Based on Molecularly Imprinted Polymer for Electrochemical Determination of Diazinon in Biological and Environmental Samples

The wide use of pesticides can lead to environmental and human adverse effects. Diazinon, as an organophosphorous pesticide, is used in agriculture because of its low cost and high efficiency on insects. Due to the increasing application of pesticides, accurate analytical methods are necessary. The aim of this work was modification of carbon paste electrode composition and applying it as a sensor for determination of diazinon in biological and environmental samples. Multi‐walls carbon nanotubes and a molecularly imprinted polymer were used as modifiers in the sensor composition. A molecularly imprinted polymer and a non‐imprinted polymer were synthesized for applying in the electrode. After optimization of electrode composition, it was used to determine the analyte concentration. Instrumental parameters affecting the square wave voltammetric response were adjusted to obtain the highest current intensity. The modified electrode with MIP showed very high recognition ability compared to the electrode containing NIP. The obtained linear range was 5×10⁻¹⁰ to 1×10⁻⁶ mol L⁻¹. The detection limit of the sensor was 1.3×10⁻¹⁰ mol L⁻¹ and the relative standard deviation for analysis of target molecule by the proposed sensor was 2.87 %. This sensor was used to determine the diazinon in real samples (human urine, tap, and river water samples) without special sample preparation before analysis. The optimization of electrode composition containing mentioned modifiers improved its response considerably.     

分子印迹电化学传感器的研究进展

本文综述了分子印迹电化学传感器的制备及其在电分析化学领域中的应用研究。引用文献83篇。     

基于石墨烯分子印迹电化学传感器测定芦丁

将石墨烯(GR)滴涂至裸Au电极表面,并以邻氨基酚为功能单体,芦丁为模板分子,制备了芦丁分子印迹膜电化学传感器,利用循环伏安法(CV)和差分脉冲伏安法(DPV)对制得的传感器进行了电化学性能研究,并且对制备条件和测定条件进行了优化。结果表明,与裸Au电极相比,该GR修饰的Au电极在[Fe(CN)_6]~(3-/4-)溶液中峰电流明显增大,显著提高了芦丁分子印迹传感器的灵敏度。在最优实验条件下,基于GR分子印迹电化学传感器在4.40×10~(-6)~2.80×10~(-4) mol/L范围内呈良好的线性关系,检测限为1.46×10~(-6) mol/L。用该传感器测定了黑茶中芦丁的含量,获得较好结果。     

Molecularly Imprinted Polypyrrole for DNA Determination

In this study graphite electrodes modified by a thin DNA‐imprinted polypyrrole layer, which was able to bind specific target‐DNA, are reported. For this aim, electrochemical synthesis of polypyrrole was performed on a pencil graphite electrode by cyclic voltammetry (CV) or by potential pulse sequences (PPS). The modified electrode surface was used for electrochemical determination of target‐DNA by differential pulse voltammetry. According to our best knowledge this is a first report on the application of DNA‐imprinted polymer for the determination of target‐DNA. The results showed that the molecularly imprinted polypyrrole (MIPPy) layer that formed on the carbon electrode surface was sensitive for target‐DNA, while the nonimprinted polypyrrole layer was not sensitive to the same target‐DNA. Comparison of electrodes modified using PPS and CV techniques is presented.     

Development of Uric Acid Sensor Based on Molecularly Imprinted Polymer‐Modified Hanging Mercury Drop Electrode

Uric acid (UA) sensor based on molecularly imprinted polymer‐modified hanging mercury drop electrode was developed for sensitive and selective analysis in aqueous and blood serum samples. The uric acid‐imprinted polymer was prepared from melamine and chloranil and coated directly onto the surface of a hanging mercury drop electrode, under charge‐transfer interactions at +0.4 V (vs. Ag/AgCl), in model 303A electrode system connected with a polarographic analyzer/stripping voltammeter (PAR model 264A). The binding event of uric acid was detected in the imprinted polymer layer through differential pulse, cathodic stripping voltammetry (DPCSV) at optimized operational conditions [accumulation potential +0.4 V (vs. Ag/AgCl), accumulation time 120 s, pH 7.0, scan rate 10 mV s^?1, pulse amplitude 25 mV]. The limit of detection for UA was found to be 0.024 μg mL^?1 (RSD=0.64%, S/N=3). Under the optimized operational conditions, the sensor was able to differentiate between uric acid and other closely structural‐related compounds and interfering substances. Ascorbic acid (AA), a major interferent in UA estimation, was not adsorbed on the surface of sensor electrode. The present sensor is, therefore, UA‐selective at all concentrations of AA present in human blood serum samples. The précised and accurate quantification of UA have been made in the dilute as well as concentrated regions varying within limits 0.1–4.0 and 9.8–137.0 μg mL^?1, respectively.     

A Novel Electrochemical Sensor Based on Molecularly Imprinted Solid-Phase Extraction for Rapid Determination of Ractopamine in Pig Urine

A new absorbent (polymer) for solid-phase extraction of ractopamine (RAC) was synthesized on the multi-walled carbon nanotubes (MWCTs) using grafting technique and surface imprinting methods. The superficial characteristics of the polymer were studied by scanning electron microscopy (SEM) and UN spectrometry was applied to investigate the static and kinetic adsorption capacity of the new absorbent. After the experimental conditions for the solid-phase extraction of RAC were optimized, a sensing system for the determination of RAC was established by connecting the solid-phase extraction column with a portable amperometric sensing system. The SEM study showed that numbers of imprinted micro-pores were exhibited on the surface of the imprinted polymers, and the absorption experiments indicated that the molecularly imprinted absorbent possessed satisfactory kinetics for the adsorption of ractopamine. The current response of the amperometric sensor demonstrated a linear correlation to the concentration of RAC over the range of 50 to 450 nM (r = 0.998) and the detection limit was 15 nM. Satisfactory sensitivity and stability was also presented under the optimized experimental conditions. The recoveries of RAC samples reached 87.3–94.8% in urine sample.     

盐酸阿霉素分子印迹传感器的制备及识别特性

采用自组装以及电聚合的方法,在磷酸盐缓冲液(PBS)中以3,4-乙烯二氧噻吩(EDOT)为功能单体,盐酸阿霉素(DOX)为模板,在金电极表面电聚合制备DOX印迹敏感膜(MIPs),构建了一种选择性检测DOX的分子印迹电化学传感器.采用循环伏安法(CV)及交流阻抗法(EIS)对其性能进行了表征.优化实验条件后,在含0.005 mol/L K3[Fe(CN)_6]及0.1 mol/L KCl的PBS中,应用差分脉冲伏安法(DPV)测试了该传感器的响应性能.实验结果表明,该传感器检测DOX的线性范围为4.0×10~(-7)~1.0×10~(-6)mol/L,相关系数为0.9967,检出限(S/N=3)达6.5×10~(-8)mol/L;采用电化学洗脱法可使传感器再生,对DOX的测定具有良好重现性及稳定性;该传感器对于干扰物长春碱、放线菌素D及5-氟尿嘧啶有微弱的电流响应,显示出良好的选择性.将该传感器用于人体血样中盐酸阿霉素的分析,回收率为96.0%~106.7%,表明其具有潜在的实用价值.     

以马来松香丙烯酸乙二醇酯为交联剂的咖啡因分子印迹电化学传感器

以咖啡因为模板分子, 含菲环骨架的马来松香丙烯酸乙二醇酯为交联剂, 甲基丙烯酸为功能单体, 在玻碳电极表面以自由基热聚合的方式制备分子印迹聚合物敏感膜, 构建了测定咖啡因的新型分子印迹膜电化学传感器. 通过循环伏安法、 差分脉冲伏安法及电化学交流阻抗法研究了传感器对咖啡因的响应特性. 结果表明, 在最佳的实验条件下, 传感器的峰电流与咖啡因浓度在3.00×10^-3~2.73 mmol/L范围内呈现良好的线性关系, 检出限(S/N=3)为1.12×10^-4 mmol/L. 传感器具有良好的选择性和重现性. 将该传感器用于可口可乐饮料中咖啡因含量的测定, 平均回收率为98.7%.     

碳纳米管修饰电极分子印迹传感器的制备及其对氧乐果的测定

以氧乐果为模板分子,邻苯二胺为功能单体,在碳纳米管修饰的玻碳电极表面通过电聚合方法制成氧乐果分子印迹聚合物膜,用无水乙醇洗脱后制备出对氧乐果有特异响应的电化学传感器。通过循环伏安法和电化学阻抗法对分子印迹传感器的电化学性能进行表征。以K_3Fe(CN)_6为探针,采用差分脉冲伏安法研究了该分子印迹传感器的分析性能,建立了氧乐果的间接测定方法。结果表明,K_3Fe(CN)_6的相对峰电流与氧乐果浓度在1.0×10~(-7)~2.0×10~(-6)mol/L范围内呈良好的线性关系,检出限为3.6×10~(-8)mol/L。     

基于抗原决定基的胰岛素分子印迹电化学传感器

采用抗原决定基法制备了胰岛素电化学分子印迹传感器.以胰岛素C端多肽作为模板分子,定向自组装在Au电极上,以邻苯二胺为功能单体,电化学聚合制备分子印迹聚合膜.以NaOH为洗脱液,洗脱模板分子,形成的与胰岛素C端多肽三维结构相匹配的分子印迹孔穴能特异性识别胰岛素.重吸附胰岛素分子后,以K3[Fe(CN)6]/K4[Fe(CN)6]为探针,通过测量探针在电极表面产生的电流大小实现胰岛素的间接测定.在1.0 × 10-14~5.0 × 10-13 mol/L浓度范围内,传感器的电流响应值与胰岛素浓度呈良好的线性关系,检出限为7.24 × 10-15 mol/L(3σ).此传感器具有较好的选择性和稳定性,并成功用于血清样品中胰岛素的测定.