Determination of Parathion‐methyl in Vegetables by Fluorescent‐Labeled Molecular Imprinted Polymer

A novel sensor for the determination of parathion‐methyl based on couple grafting of functional molecular imprinted polymers (MIPs) was fabricated which is developed by anchoring the MIP layer on surfaces of silica particles embedded CdSe quantum dots by surface imprinting technology. The synthesized molecular imprinted silica nanospheres (CdSe@SiO₂@MIP) allow a high selectivity and sensitivity of parathion‐methyl via fluorescence intensity decreasing when the MIP material rebinding the parathion‐methyl molecule. Compared with the MIP fabricated in traditional method, the template of parathion‐methyl was easier to remove from the CdSe@SiO₂@MIP imprinted material. Under optimal conditions, the fluorescence intensity of parathion‐methyl at the imprinted sensor was detected by spectrofluorophotometer. The relative fluorescence intensity of CdSe@SiO₂@MIP decreased linearly with the increasing concentration of parathion‐methyl ranging from 0.013 mg·kg⁻¹ to 2.63 mg·kg⁻¹ with a detection limit (3δ) of 0.004 mg·kg⁻¹ (S/N=3), which is lower than the MIP in tradition. The imprinted film sensor was applied to detect parathion‐methyl in vegetable samples without the interference of other organophosphate pesticides and showed a prosperous application in the field of food safety.     

Preparation and application of a novel molecularly imprinted solid‐phase microextraction monolith for selective enrichment of cholecystokinin neuropeptides in human cerebrospinal fluid

A novel molecularly imprinted polymer (MIP) monolith for highly selective extraction of cholecystokinin (CCK) neuropeptides was prepared in a micropipette tip. The MIPs were synthesized by epitope imprinting technique and the polymerization conditions were investigated and optimized. The synthesized MIPs were characterized by infrared spectroscopy, elemental analyzer and scanning electron microscope. A molecularly imprinted solid‐phase microextraction (MI‐μ‐SPE) method was developed for the extraction of CCK neuropeptides in aqueous solutions. The parameters affecting MI‐μ‐SPE were optimized. The results indicated that this MIP monolith exhibited specific recognition capability and high enrichment efficiency for CCK neuropeptides. In addition, it showed excellent reusability. This MIP monolith was used for desalting and enrichment of CCK4, CCK5 and CCK8 from human cerebrospinal fluid prior to matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry analysis, and the results show that this MIP monolith can be a useful tool for effective purification and highly selective enrichment of multiple homologous CCK neuropeptides in cerebrospinal fluid simultaneously. By employing MI‐μ‐SPE combined with HPLC‐ESI‐MS/MS analysis, endogenous CCK4 in human cerebrospinal fluid was quantified. Copyright © 2015 John Wiley & Sons, Ltd.     

An Energetic Triazolo‐1,2,4‐Triazine and its N‐Oxide

The reaction of 3‐amino‐5‐nitro‐1,2,4‐triazole with nitrous acid produces the corresponding diazonium salt. When the diazonium salt is treated with nitroacetonitrile, a subsequent condensation and cyclization reaction occurres to produced 4‐amino‐3,7‐dinitrotriazolo‐[5,1‐c][1,2,4] triazine (DPX‐26). X‐ray crystallographic analysis shows that the DPX‐26 has a density of 1.86 g cm^?3, while it is calculated to have a heat of formation of 398.3 kJ mol^?1. DPX‐26 is predicted to approach the explosive performance of RDX but displays significantly better safety properties. Oxidation of DPX‐26 using hypofluorous acid produces 4‐amino‐3,7‐dinitrotriazolo‐[5,1‐c][1,2,4] triazine 4‐oxide (DPX‐27), which is also predicted to be a high‐performance material with enhanced safety properties.     

Synthesis of molecularly imprinted polypyrrole as an adsorbent for solid‐phase extraction of warfarin from human plasma and urine

The aim of this work was to develop a method for the clean‐up and preconcentration of warfarin from biological sample employing a new molecularly imprinted polymer (MIP) as a selective adsorbent for solid‐phase extraction (SPE). This MIP was synthesized using warfarin as a template, pyrrole as a functional monomer and vinyl triethoxysilane as a cross‐linker. The molar ratio of 1:4:20 (template–functional monomer–cross‐linker) showed the best results. Nonimprinted polymers (NIPs) were prepared and treated with the same method, but in the absence of warfarin. The prepared polymer was characterized by Fourier transmission infrared spectrometry and scanning electron microscopy. An adsorption process (SPE) for the removal of warfarin using the fabricated MIPs and NIPs was evaluated under various conditions. Effective parameters on warfarin extraction, for example, type and volume of elution solvent, pH of sample solution, breakthrough volume and maximum loading capacity, were studied. The limits of detection were in the range of 0.0035–0.0050 µg mL^?1. Linearity of the method was determined in the range of 0.0165–10.0000 µg mL^?1 for plasma and 0.0115–10.0000 µg mL^?1 for urine with coefficients of determination (R²) ranging from 0.9975 to 0.9985. The recoveries for plasma and urine samples were >95%. Copyright © 2015 John Wiley & Sons, Ltd.     

Development of a Creatinine Sensor Based on a Molecularly Imprinted Polymer‐Modified Sol‐Gel Film on Graphite Electrode

An electrochemical creatinine sensor based on a molecularly imprinted polymer (MIP)‐modified sol‐gel film on graphite electrode was developed. The surface coating of MIP over sol‐gel was advantageous to obtain a porous film with outwardly exposed MIP cavities for unhindered selective rebinding of creatinine from aqueous and biological samples. A fast differential pulse, cathodic stripping voltammetric response of creatinine can be obtained after being preanodized the sensor in neutral medium containing appropriate amount of creatinine at +1.8 V versus SCE for 120 s. A linear response over creatinine concentration in the range of 1.23 to 100 μg mL^?1 was exhibited with a detection limit of 0.37 μg mL^?1 (S/N=3).     

Investigation of the Reaction of Gold(III) with 2‐[2‐(4‐Dimethylamino‐Phenyl)‐Vinyl]‐1,3,3‐Trimethyl‐3H‐Indolium. Application for Determination of Gold

A new, simple, rapid, sensitive, efficient and low‐cost spectrophotometric procedure for the determination of gold was developed. The method is based on the reaction of [AuCl₄]^? with 2‐[2‐(4‐dimethylaminophenyl)‐vinyl]‐1,3,3‐trimethyl‐3H‐indolium reagent to form a colored ion associate extractable by various organic solvents. The molar absorptivity of the ion associates is in the range (5.7–9.2) × 10⁴ L mol^?1 cm^?1 depending on the extractant. Butyl acetate was chosen as the extractant. The optimum reaction conditions were established: pH 2–4, concentration of the dye reagent (0.8–1.5) × 10^?4 mol L^?1. The determination of gold is not hindered even by a 1000‐fold concentration of Ni and Co; a 500‐fold concentration of Pb and Zn; a 100‐fold concentration of Bi, Cu, Cd, Pt, Rh and Ru; or a 20‐fold concentration of Ag. The established method was applied to the determination of gold in model samples and enriched polymetallic ores.     

Ion Transport Across Liquid|Liquid Interfacial Boundaries Monitored at Generator‐Collector Electrodes

Anion transfer processes at a liquid|liquid interface were studied with an interdigitated gold band array electrode. The organic phase, 4‐(3‐phenylpropyl)‐pyridine containing Co(II)phthalocyanine, was immobilised as random droplets at the electrode surface and then immersed into aqueous electrolyte. Oxidation of Co(II)phthalocyanine at the generator electrode was shown to be associated with anion transfer from the aqueous into the organic phase. The corresponding back reduction at the collector electrode with anion expulsion was delayed by the anion/cation diffusion time across the interelectrode gap. A working curve based on a finite difference numerical simulation model was employed to estimate the apparent diffusion coefficients for anions in the organic phase (PF₆^?4^?3^?). Potential applications in ion analysis are discussed.     

A Sensitive Surface‐enhanced Raman Scattering Method for Determination of Melamine with Aptamer‐modified Nanosilver Probe

The small nanosilver was prepared by the sodium borohydride procedure. The aptamer was used to modify nanosilver to obtain a nanosilver‐aptamer (AgssDNA) SERS probe for the determination of melamine. In pH 6.6 phosphate buffer solution and in the presence of NaCl, the AgssDNA probe specifically combined with melamine to release nanosilver particles that were aggregated to nanosilver clusters, which exhibited SERS effect at 240 cm^?1. When melamine concentration increased, the nanosilver clusters increased, and the SERS intensity at 240 cm^?1 increased. The increased SERS intensity ΔI_{240 cm?1} is linear to melamine concentration in the range of 6.3–403.6 μg·L^?1, with a detection limit of 1.2 μg·L^?1. This assay was applied to determination of melamine in milk, with satisfactory results.     

Development of solid‐phase microextraction coupled with liquid chromatography for analysis of tramadol in brain tissue using its molecularly imprinted polymer

In this work, performance of a molecularly imprinted polymer (MIP) as a selective solid‐phase microextraction sorbent for the extraction and enrichment of tramadol in aqueous solution and rabbit brain tissue, is described. Binding properties of MIPs were studied in comparison with their nonimprinted polymer (NIP). Ten milligrams of the optimized MIP was then evaluated as a sorbent, for preconcentration, in molecularly imprinted solid‐phase microextraction (MISPME) of tramadol from aqueous solution and rabbit brain tissue. The analytical method was calibrated in the range of 0.004 ppm (4 ng mL⁻¹) and 10 ppm (10 μg mL⁻¹) in aqueous media and in the ranges of 0.01 and 10 ppm in rabbit brain tissue, respectively. The results indicated significantly higher binding affinity of MIPs to tramadol, in comparison with NIP. The MISPME procedure was developed and optimized with a recovery of 81.12–107.54% in aqueous solution and 76.16–91.20% in rabbit brain tissue. The inter‐ and intra‐day variation values were <8.24 and 5.06%, respectively. Finally the calibrated method was applied for determination of tramadol in real rabbit brain tissue samples after administration of a lethal dose. Our data demonstrated the potential of MISPME for rapid, sensitive and cost‐effective sample analysis.     

Sugar acrylate‐based polymers as chiral molecularly imprintable hydrogels

New polymeric hydrogels with molecular imprinting properties were prepared from enzymically generated sugar acrylates. These so called MIPs (molecularly imprinted polymers) were used as chiral stationary phases for the resolution of the D ‐ and L ‐isomers of CBz–Asp in polar organic eluants. In the presence of 25% (mol/mol) methyl‐α‐D ‐glucopyranoside‐6‐acrylate [the balance consisting of N,N′‐methylenebisacrylamide (BIS)], a separation factor of nearly 2.5 is achieved. The effectiveness of separation was dependent on the nature of the solvent used as eluant and the sugar incorporated into the MIP. Molecular modeling revealed that hydrogen bonding between the sugar and CBz–Asp strongly influences chiral resolution. The broad array of sugars available and their ability to be modified selectively with the use of biocatalysts in both aqueous and organic media may provide a wide range of new imprinted materials for use in separations, sensing, and catalysis. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1665–1671, 1999     

Highly Stereoselective β‐Mannopyranosylation via the 1‐α‐Glycosyloxy‐isochromenylium‐4‐gold(I) Intermediates

While the gold(I)‐catalyzed glycosylation reaction with 4,6‐O‐benzylidene tethered mannosyl ortho‐alkynylbenzoates as donors falls squarely into the category of the Crich‐type β‐selective mannosylation when Ph₃PAuOTf is used as the catalyst, in that the mannosyl α‐triflates are invoked, replacement of the ^?OTf in the gold(I) complex with less nucleophilic counter anions (i.e., ^?NTf₂, ^?SbF₆, ^?BF₄, and ^?BAr₄^F) leads to complete loss of β‐selectivity with the mannosyl ortho‐alkynylbenzoate β‐donors. Nevertheless, with the α‐donors, the mannosylation reactions under the catalysis of Ph₃PAuBAr₄^F (BAr₄^F=tetrakis[3,5‐bis(trifluoromethyl)phenyl]borate) are especially highly β‐selective and accommodate a broad scope of substrates; these include glycosylation with mannosyl donors installed with a bulky TBS group at O3, donors bearing 4,6‐di‐O‐benzoyl groups, and acceptors known as sterically unmatched or hindered. For the ortho‐alkynylbenzoate β‐donors, an anomerization and glycosylation sequence can also ensure the highly β‐selective mannosylation. The 1‐α‐mannosyloxy‐isochromenylium‐4‐gold(I) complex ( Cα ), readily generated upon activation of the α‐mannosyl ortho‐alkynylbenzoate ( 1 α ) with Ph₃PAuBAr₄^F at ?35 °C, was well characterized by NMR spectroscopy; the occurrence of this species accounts for the high β‐selectivity in the present mannosylation.     

Efficient one‐pot synthesis of water‐compatible and photoresponsive molecularly imprinted polymer nanoparticles by facile RAFT precipitation polymerization

A facile, general, and highly efficient one‐pot approach to obtain azobenzene (azo)‐containing molecularly imprinted polymer (MIP) nanoparticles with photoresponsive template binding and release properties in aqueous media is described, which involves the combined use of hydrophilic macromolecular chain transfer agent‐mediated reversible addition‐fragmentation chain transfer precipitation polymerization and easily available water‐insoluble azo functional monomers. The resulting azo‐containing MIPs were characterized with dynamic laser scattering (DLS), SEM, FTIR, static contact angle and water dispersion studies, and equilibrium binding experiments. They have proven to be nanoparticles (their diameters being around 104–397 nm, as determined by DLS in methanol) with surface‐grafted hydrophilic polymer brushes and exhibit excellent pure water‐compatible template binding properties. Moreover, obvious photoregulated template binding behaviors were observed for such azo‐containing MIP nanoparticles, which led to their largely accelerated template release in the aqueous media under the UV light irradiation. Furthermore, the general applicability of the strategy was also demonstrated. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1941–1952     

Synthesis and Characterization of Gold‐Nanoparticle‐Cored Dendrimers Stabilized by Metal–Carbon Bonds

Synthesis and characterization of gold‐nanoparticle‐cored dendrimers (NCDs), in which the dendrons are attached to the gold core through gold–carbon bonds, are described. Synthesis of these materials involved the simultaneous reduction of HAuCl₄ and a Fréchet‐type dendron with a diazonium group at the focal point, all in an organic solvent such as toluene. These materials possess a nanometer‐sized gold core surrounded by a shell of polyaryl ether dendrons, which are connected radially to the core. The NCDs were characterized by TEM, thermogravimetric analysis (TGA), and IR, UV, and NMR spectroscopic techniques. Average particle diameter of the NCDs ranged from 4.7 to 5.5 nm for the different generations. All NCDs exhibit the characteristic plasmon absorption of gold nanoparticles at 520 nm. Average numbers of dendrons per NCD in AuG_n were calculated using results from TGA and TEM studies. Multiple layering of the dendrons is proposed as a possible reason for the high dendron/NCD value.     

Ligand‐Assisted Gold‐Catalyzed Cross‐Coupling with Aryldiazonium Salts: Redox Gold Catalysis without an External Oxidant

Gold‐catalyzed C(sp)–C(sp²) and C(sp²)–C(sp²) cross‐coupling reactions are accomplished with aryldiazonium salts as the coupling partner. With the assistance of bpy ligand, gold(I) species were oxidized to gold(III) by diazonium without any external oxidants. Monitoring the reaction with NMR and ESI‐MS provided strong evidence for the nitrogen extrusion followed by Au^III reductive elimination as the key step.     

Electrochemical Determination of Tetracycline Using Molecularly Imprinted Polymer Modified Carbon Nanotube‐Gold Nanoparticles Electrode

This paper reports the use of a tetracycline (TC) sensor constructed from a combination of molecularly imprinted polymer (MIP) and gold nanoparticles modified multiwall carbon nanotubes (MWNTs‐GNPs). The results demonstrated that the amount of recognition sites in the polymer was significantly increased and the electron transfer ability of the sensor was improved. The relationship between the peak current and the TC concentration was linear in the range from 0.1 to 40 mg L^?1, and the detection limit was 0.04 mg L^?1 (S/N=3). The peak current to TC was 4.3, 6.2 and 6.8 times larger than that of oxytetracycline, chloramphenicol and nafcillin, respectively. Thus, the combination of MIP and MWNTs‐GNPs provides a sensitive and selective electrochemical detection method for tetracycline.     

Enzyme‐Initiated Free‐Radical Polymerization of Molecularly Imprinted Polymer Nanogels on a Solid Phase with an Immobilized Radical Source

An enzyme‐mediated synthetic approach is described for the preparation of molecularly imprinted polymer nanoparticles (MIP‐NPs) in aqueous media. Horseradish peroxidase (HRP) was used to initiate the polymerization of methacrylate or vinyl monomers and cross‐linkers by catalyzing the generation of free radicals. To prevent entrapment of the enzyme in the cross‐linked polymer, and to enable it to be reused, HRP was immobilized on a solid support. MIPs based on 4‐vinylpyridine and 1,4‐bis(acryloyl)piperazine for the recognition of 2,4‐dichlorophenoxyacetic acid (2,4‐D) and salicylic acid were synthesized in an aqueous medium. MIPs for the protein trypsin were also synthesized. MIP nanoparticles with sizes between 50 and 300 nm were obtained with good binding properties, a good imprinting effect, and high selectivity for the target molecule. The reusability of immobilized HRP for MIP synthesis was shown for several batches.     

Gold‐loading magnetic core–shell organic/inorganic nanocomposites: facile preparation and multiple properties

Magnetic composite nanospheres (MCS) were first prepared via mini‐emulsion polymerization. Subsequently, the hybrid core–shell nanospheres were used as carriers to support gold nanoparticles. The as‐prepared gold‐loading magnetic composite nanospheres (Au‐MCS) had a hydrophobic core embed with γ‐Fe₃O₄ and a hydrophilic shell loaded by gold nanoparticles. Both the content of γ‐Fe₃O₄ and the size of gold nanoparticles could be controlled in our experiments, which resulted in fabricating various materials. On one hand, the Au‐MCS could be used as a T₂ contrast agent with a relaxivity coefficient of 362 mg^?1 ml S^?1 for magnetic resonance imaging. On the other hand, the Au‐MCS exhibited tunable optical‐absorption property over a wavelength range from 530 nm to 800 nm, which attributed to a secondary growth of gold nanoparticles. In addition, dynamic light scattering results of particle sizing and Zeta potential measurements revealed that Au‐MCS had a good stability in an aqueous solution, which would be helpful for further applications. Finally, it showed that the Au‐MCS were efficient catalysts for reductions of hydrophobic nitrobenzene and hydrophilic 4‐nitrophenol that could be reused by a magnetic separation process. Copyright © 2014 John Wiley & Sons, Ltd.     

Electrochemistry and Ion Sensing Properties of Conducting Hydrogel Layers Based on Polypyrrole and Alkoxysulfonated Poly(3,4‐ethylenedioxythiophene) (PEDOT‐S)

Acidic aqueous solutions containing pyrrole and alkoxysulfonated PEDOT derivative (PEDOT‐S) were found to undergo polymerization in the absence of an external oxidizing agent. The product was a nearly black‐colored conducting hydrogel that after separation could be dispersed in water or acetone. The suspensions could be used to deposit cast films on a polycrystalline gold electrode. The polymer modified electrode showed a nearly Nernstian potentiometric response to Ag⁺ cations in the concentration range of 10^?5–10^?1 M with the slope of 54 mV/decade. The response was specific to Ag⁺ compared to a series of alkali and transition‐metal cations (pK_Ag/M>3.7).     

Direct Electrochemistry and Electrocatalysis of the Hemoglobin Immobilized on Diazonium‐Functionalized Aligned Carbon Nanotubes Electrode

A simple and efficient electrochemical method is utilized to functionalize aligned carbon nanotubes (ACNTs) by the electrochemical reduction of 4‐carboxyphenyl diazonium salt. Thus hemoglobin (Hb) molecules were covalently immobilized on the diazonium‐ACNTs surface via carbodiimide chemistry. Direct electrochemistry and bioelectrocatalytic activity of the immobilized Hb were then investigated by cyclic voltammetry (CV) and amperometry techniques. It is showed that the Hb film on the diazonium‐ACNTs electrode had well‐defined redox peaks with a formal potential (E°) at ?312 mV (vs. Ag/AgCl), and the Hb‐ACNTs electrode displayed good electrocatalytic activity to H₂O₂ reduction. Owing to the high Hb covering on the ACNTs surface (Γ*=2.7×10^?9 mol cm^?2), the catalytic current were significantly improved when compared to the current measured at an Hb‐tangled carbon nanotubes electrode. The Hb‐ACNTs electrode exhibited high sensitivity, long‐term stability and wide concentration range from 40 μM to 3 mM for the amperometric detection of H₂O₂. The heterogeneous reaction rate constant (k_s) was 0.95±0.05 s^?1 and the apparent Michaelis–Menten constant (K was 0.15 mM.     

Voltammetric Determination of Urinary 1‐Hydroxypyrene Using Molecularly Imprinted Polymer‐Modified Screen‐Printed Carbon Electrodes

A two step non‐competitive affinity method for the trace determination of 1‐hydroxypyrene (1‐OHP) using a disposable molecularly imprinted polymer (MIP) modified screen‐printed carbon electrode (MIP‐SPCE) has been developed. The MIP was synthesized according to a novel strategy, which is described, and is capable of rebinding the phenolic analyte, 1‐hydroxypyrene (1‐OHP), from high pH aqueous organic media, via ionic interactions. In the first step of our method 1‐OHP was accumulated at the MIP‐SPCE from 35% aqueous methanol containing 0.014 M NaOH and 0.14 M NaCl, at open circuit. In the second step, the resulting SPCE with accumulated 1‐OHP was then transferred to fresh, clean phosphate buffered aqueous methanol, and subjected to cyclic voltammetry (CV) or differential pulse voltammetry (DPV). The latter technique proved to be more sensitive at detecting 1‐OHP, with a limit of detection of 182 nM and a linear range to 125 μM on unmodified electrodes. The possible effects of interference by related phenolic compounds in the MIP‐SPCE of 1‐OHP were investigated. Finally the method was evaluated by carrying out 1‐OHP determinations on spiked human urine samples; the recovery of 1‐OHP was 79.4% and the coefficient of variation was found to be 7.7% (n= 4) using a separate MIP‐SPCE for each determination. Therefore, the performance data suggests that the method is reliable at the concentrations examined in this study. The method was found to be superior to the direct determination of 1‐OHP in human urine by DPV alone, which was greatly affected by interference from uric acid.