Preparation and Properties of Poly（vinyl alcohol）/Chitosan Blend Bio-nanocomposites Reinforced by Cellulose Nanocrystals

The aim of this paper is to report the effect of the addition of cellulose nanocrystals（CNCs） on the mechanical, thermal and barrier properties of poly（vinyl alcohol）/chitosan（PVA/Cs） bio-nanocomposites films prepared through the solvent casting process. The characterizations of PVA/Cs/CNCs films were carried out in terms of X-ray diffraction（XRD）, transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, thermogravimetric analysis（TGA and DTG）, oxygen transmission rate（OTR）, and tensile tests. TEM and SEM results showed that at low loading levels, CNCs were dispersed homogenously in the PVA/Cs matrix. The tensile strength and modulus in films increased from 55.1 MPa to 98.4 MPa and from 395 MPa to 690 MPa respectively, when CNCs content went from 0 wt% to 1.0 wt%. The thermal stability and oxygen barrier properties of PVA/Cs matrix were best enhanced at 1.0 wt% of CNCs loading. The enhanced properties attained by incorporating CNCs can be beneficial in various applications.     

Development of sodium alginate-xanthan gum based nanocomposite scaffolds reinforced with cellulose nanocrystals and halloysite nanotubes

Sodium alginate (Alg) and xanthan gum (XG) based nanocomposite scaffolds reinforced with various amounts of cellulose nanocrystals (CNCs) and/or halloysite nanotubes (HNTs) were prepared by freeze-casting/drying method. In this study, the structure-property-performance relationship was mainly focused and analysed. Morphological analysis showed high porosity and pore-interconnectivity (pore channels) in all obtained scaffolds. Structural analysis demonstrates the good interfacial interactions and uniform dispersion of the CNCs and HNTs, involving partial orientation within the polymeric network. The water uptake capacity (from 14.73.7 ± 0.46 g/g to 11.34 ± 0.32 g/g) and porosity (from 91.7 ± 0.81% to 88.5 ± 0.64%) were reduced. The compressive strengths (in dry state from 91.1 ± 1.2 kPa to 114.4 ± 0.6 kPa and in wet state from 9.0 ± 0.8 kPa to 10.6 ± 0.8 kPa), thermal stability, cytocompatibility (MC3T3-E1 osteoblastic cells) of the nanocomposite scaffolds improved as compared to Alg and AlgX scaffolds without CNCs and/or HNTs. The obtained scaffolds may be appropriate as scaffolding material in bone tissue engineering.     

Insight into the extraction and characterization of cellulose nanocrystals from date pits

This study aims to extract and characterize cellulose nanocrystals (CNCs) from date pits (DP), an agricultural solid waste. Two methods were used and optimized for the cellulose nanocrystals (CNCs) extraction, namely the mechanical stirrer method (CNCs₁) and the Soxhlet apparatus method (CNCs₂) in terms of chemical used, cost, and energy consumption. The results showed that scanning electron microscopy revealed the difference in the morphology as they exhibit rough surfaces with irregular morphologies due to the strong chemical treatments during the delignification and bleaching process. Moreover, transmission electron microscopy analysis for CNCs reveals the true modification that was made through sulfuric acid hydrolysis as it presents cellulose microfibrils with a packed structure. Fourier transform infrared proved that the CNCs were successfully extracted using the two methods since most of the lignin and hemicellulose components were removed. The crystallinity index of CNCs₁ and CNCs₂ was 69.99%, and 67.79%, respectively, and both presented a high yield of CNCs (≥10%). Ultimately, both techniques were successful at extracting CNCs. Based on their cost-effectiveness and time consumption, it was concluded that method 1 was less expensive than method 2 based on the breakdown of the cost of each step for CNCs production.     

Poly(acrylamidoglycolic acid) nanocomposite hydrogels reinforced with cellulose nanocrystals for pH-sensitive controlled release of diclofenac sodium

In this study, a non-cytotoxic and pH-sensitive poly(acrylamidoglycolic acid) based nanocomposite (PAGA-NC) hydrogels reinforced with cellulose nanocrystals (CNCs) was synthesized using redox free radical polymerization. The successful formation and crystalline behaviour of PAGA-NC hydrogels was verified by fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) analyses. The results showed that morphological, rheological and mechanical properties of the PAGA-NC hydrogels were strongly influenced by the CNCs content. Moreover, swelling properties were investigated, and the results suggested that they behaved as pH sensitive manner. The in vitro MTT assay showed that the PAGA-NC hydrogels are cytocompatibile to NIH-3T3 fibroblast cells. In addition, diclofenac sodium (DCF) model drug was successfully encapsulated into these PAGA-NC hydrogels via equilibrium swelling method. The in vitro release of DCF from PAGA-NC hydrogels was retained at pH 1.2 and maximum release was observed at 7.4, revealing as potential candidates for controlled release carriers for oral drug delivery applications.     

Optimization of the isolation of nanocrystals from microcrystalline cellulose by acid hydrolysis

The objective of this work was to find a rapid, high-yield process to obtain an aqueous stable colloid suspension of cellulose nanocrystals/whiskers. Large quantities are required since these whiskers are designed to be extruded into polymers in the production of nano-biocomposites. Microcrystalline cellulose (MCC), derived from Norway spruce (Picea abies), was used as the starting material. The processing parameters have been optimized by using response surface methodology. The factors that varied during the process were the concentration of MCC and sulfuric acid, the hydrolysis time and temperature, and the ultrasonic treatment time. Responses measured were the median size of the cellulose particles/whiskers and yield. The surface charge as calculated from conductometric titration, microscopic examinations (optical and transmission electron microscopy), and observation of birefringence were also investigated in order to determine the outcome (efficiency) of the process. With a sulfuric acid concentration of 63.5% (w/w), it was possible to obtain cellulose nanocrystals/whiskers with a length between 200 and 400 nm and a width less than 10 nm in approximately 2 h with a yield of 30% (of initial weight).     

Reinforcement of hydroxypropylcellulose films by cellulose nanocrystals in the presence of surfactants

Hydroxypropylcellulose (HPC) films were prepared by casting with cellulose nanocrystals in the presence of anionic surfactant sodium dodecylsulphate (SDS) and cationic surfactant hexadecyltrimethyl ammonium bromide (CTAB). The cellulose nanocrystals were isolated from maize straw, a biomass source produced in huge quantities as an agrowaste in Brazil. These bionanocomposite films had good transparency and their surface hydrophilic character was evidenced by static contact angle measurements. Thermogravimetry (TGA) measurement revealed that nanocrystals and surfactants changed the thermal stability of the HPC films. Dynamic mechanical analysis (DMA) showed that the tensile storage and loss moduli of the HPC films increased by increasing the contents of cellulose nanocrystals and surfactants, especially in the case of CTAB. This good reinforcing effect of HPC matrix can be explained as due to electrostatic attractive interactions brought about by the presence of CTAB and the nanocrystals.     

Effect of chitosan and ions on actuation behavior of cellulose–chitosan laminated films as electro-active paper actuators

Cellulose-chitosan laminated films were made for Electro-Active Paper (EAPap) actuators and the effect of chitosan and different types of free ions namely, Cl⁻, NO₃⁻ and CF₃COO⁻ were investigated on the actuation behavior. The fabrication process of the films was explained and the actuation performance was tested in terms of bending displacement of the actuators. It was observed that, chitosan content and type of free ions influence the tip displacement of the actuators. Cl⁻ was found the best free ion among others, and detail observations are explained. By laminating chitosan layer on the cellulose films, the humidity sensitiveness of cellulose EAPap actuators was reduced.     

Treatment of oxidized cellulose fabric with chitosan and its surface activity towards anionic reactive dyes

The surface modification of cellulose fabric with chitosan was achieved through an oxidation of the fabric with KIO₄ followed by reductive ammination with chitosan. The chitosan content in the fabric determined by Kjeldahl nitrogen analysis technique was 1.69%. The scanning electron micrograph revealed submicron particles of chitosan attached on the fabric surface. Dyeing of the modified fabrics with mono-chloro-triazine and vinyl sulfone anionic reactive dyes, showed vastly improved exhaustion and color yield (K/S) indicating that this method of surface modification is effective for changing surface activity of the fabric. The enhancement of the dye uptake brought about an improved dyeing process in which the dye and salt used could be reduced by half and 14%, respectively. A Significant drop in burst strength upon the oxidation but no discernable adverse color fastness property was observed for the chitosan-modified fabric.     

Characterization and biocompatibility of chitosan nanocomposites

Chitosan nanocomposites were prepared from chitosan and gold nanoparticles (AuNPs) or silver nanoparticles (AgNPs) of ～5 nm size. Transmission electron microscopy (TEM) showed the NPs in chitosan did not aggregate until higher concentrations (120-240 ppm). Atomic force microscopy (AFM) demonstrated that the nanocrystalline domains on chitosan surface were more evident upon addition of AuNPs (60 ppm) or AgNPs (120 ppm). Both nanocomposites showed greater elastic modulus, higher glass transition temperature (T(g)) and better cell proliferation than the pristine chitosan. Additionally, chitosan-Ag nanocomposites had antibacterial ability against Staphylococcus aureus. The potential of chitosan-Au nanocomposites as hemostatic wound dressings was evaluated in animal (rat) studies. Chitosan-Au was found to promote the repair of skin wound and hemostasis of severed hepatic portal vein. This study indicated that a small amount of NPs could induce significant changes in the physicochemical properties of chitosan, which may increase its biocompatibility and potential in wound management.     

Effect of organic and inorganic acids on chitosan/glycerophosphate thermosensitive hydrogel

The influence of organic and inorganic acids on chitosan/glycerophosphate (CS/GP) hydrogel has been investigated by dissolving chitosan in different acids. The results of gelation showed that all of the chitosan dissolved in monovalent acid solutions (i.e., formic, acetic, propionic, butyric, isobutyric, lactic, nitric, hydrochloric, and chloroacetic acid), when neutralized by GP solution, could transform into hydrogel after 2–5 min at 37 °C, while those dissolved in multivalent acids failed in gel formation. The inner structures of CS/GP hydrogels prepared with monovalent acids depended on the ionic strength and chain length of acids. Morphological examination by scanning electron microphotography demonstrated that large pores occurred during the gel-forming process, and the aperture size was also related to different acids. The cytotoxicity studies indicated that CS/GP systems prepared by dissolving chitosan in tested acids except chloroacetic acid were nontoxic to mouse embryonic fibroblasts and Hela cells.     

Immobilization of cellulose extracted from Robinia Pseudoacacia seed fibers onto chitosan: Chemical characterization and study of methylene blue removal

The design of economical adsorbents to remove pollutants from contaminated water is attracting more attention. In this study, cellulose was successfully extracted from Robinia Pseudoacacia seed fibers and immobilized onto chitosan beads. The prepared spherical beads were then used for the biosorption of methylene blue dye from aqueous media. Samples were investigated using several analytical methods, namely FT-IR, XRD, EDX, SEM, and TGA analyses. The adsorption experiments showed that combining cellulose with chitosan improved the removal of methylene blue. The maximum uptake amount of methylene blue using cellulose–chitosan composite beads was 55 mg/g. However, it was about 35 mg/g at 20 °C for chitosan beads. The kinetic data complied strongly with the pseudo-second order equation, suggesting that the biosorption phenomenon has predominantly a chemical nature. Overall, the current study has shown a promising technique to design new adsorbents from abundant natural polymers for eliminating cationic dyes from water.     

Cellulose/chitosan hybrid nanofibers from electrospinning of their ester derivatives

A facile approach has been established to generate cellulose/chitosan hybrid nanofibers with full range of compositions by electrospinning of their ester derivatives, cellulose acetate (CA) and dibutyryl chitin (DBC), followed by alkaline hydrolysis to cellulose (Cell) and chitosan (CS). DBC was synthesized by acid-catalyzed acylation of chitin (CHI) with butyric anhydride and the newly formed butyl groups on C3 and C6 were confirmed by FT-IR and ¹HNMR. DBC had robust solubility in acetone, DMAc, DMF, ethanol, and acetic acid, all except ethanol were also solvents for CA, allowing mixing of these ester derivatives. Fiber formation by electrospinning of either DBC or CA alone and together in these common solvents and their mixtures were studied. The 1/1 acetone/acetic acid was found to be the optimal solvent system to generate fibers from either DBC or CA as well as their mixtures at all CA/DBC ratios, resulting in hybrid fibers with diameters ranging from 30 to 350 nm. DBC and CA were well mixed and showed no phase separate in the hybrid fibers. Alkaline hydrolysis (NaOH) of the equal mass CA/DBC nanofibers regenerated Cell and CHI readily via O-deacylation, then proceeded to further deacetylate CHI to CS via N-deacetylation at higher alkaline concentrations and/or temperatures. Under conditions studied, hydrolysis with 5N NaOH at 100 °C for 3 h was optimal to regenerate cellulose/chitosan hybrid nanofibers.     

Effects of cellulose nanocrystals on the vulcanization of natural rubber/cellulose nanocrystals nanocomposite and corresponding regulating strategies

Vulcanization is a vital process in rubber processing, it endows rubber with valuable physical and mechanical properties, making rubber a widely used engineering material. In addition to vulcanization agent, reinforcing fillers play a non-ignorable influence on the vulcanization of rubber nanocomposites. Herein, the effects of cellulose nanocrystals (CNCs) on the vulcanization of natural rubber (NR)/CNCs nanocomposite was studied. It was found that even though the addition of CNCs can effectively improve the dispersion of ZnO in NR matrix, the vulcanization of NR was inhibited. This may be attributed to the CNCs' adsorption of vulcanizing agents (DM, ZnO) and the acidic chemical environment on the surface of CNCs. In order to improve the vulcanization properties of NR/CNCs nanocomposite, tetramethyldithiochloram (TMTD) and triethanolamine (TEOA) were used as a combination accelerator and curing activator, respectively, and polyethylene glycol (PEG) was introduced to screen hydroxyl groups on the surface of CNCs to prohibit the CNCs' adsorption of vulcanizing agents. The results indicate that TMTD and TEOA effectively improved the vulcanization rate of NR/CNCs nanocomposite and increased the crosslink density by an order of magnitude. Subsequently, the tensile strength, tear strength, and so forth. of NR/CNCs nanocomposite were significantly improved. However, PEG hardly help to improve the vulcanization properties of NR/CNCs nanocomposite. In addition, the control samples without CNCs were prepared and characterized, the comparation between NR and NR/CNCs nanocomposite shows that the synergistic effect of crosslink density and CNCs' reinforcement more effectively improve mechanical properties of NR. This work not only elucidates the inhibiting mechanisms of CNCs on the vulcanization of NR, but also provides practical strategies for improving the vulcanization and properties of NR/CNCs nanocomposite. It may accelerate the application of CNCs as rubber reinforcing filler.     

Development of biopolymer/cellulose/silica nanostructured hybrid materials and their characterization by NMR relaxometry

The objective of this study was to investigate the preparation and properties of hybrid materials composed of poly(lactic acid) (PLA) and poly(lactic acid)/poly(lactic-co-glycolic acid) (PLA/PLGA) blends employing cellulose nanocrystals (CNCs) and/or organophilic silica (R972) as nanoparticles. The CNCs were obtained by acid hydrolysis of commercially available microcrystalline cellulose (MCC). The materials were produced in film form by solution casting. Organophilic silica was incorporated at a ratio of 3 wt.%, and CNCs were added at ratios of 3 wt.% and 5 wt.% in relation to the weight of the polymer matrix. Two series of films were obtained. The first was prepared using only PLA as the matrix, and the second was obtained using blends of PLA and PLGA. The properties of the films were evaluated by X-ray diffractometry, nuclear magnetic resonance, Fourier-transform infrared spectroscopy and measurement of mechanical properties. The results revealed that each nanoparticle, whether added individually or combined with the other type of nanoparticle, induced different final material properties. Cellulose nanocrystals can act as nucleating agents for the crystallization of PLA. There was an improvement in the mechanical performance of films with the addition of CNCs. Further, the incorporation of silica combined with CNCs resulted in the generation of films with the strongest mechanical properties. The results of this study indicate that silica decreases the surface tension between PLA-cellulose and PLA/PLGA-cellulose.     

Assembled structures of nanocrystals in polymer/calcium carbonate thin-film composites formed by the cooperation of chitosan and poly(aspartate)

Assembled structures of calcium carbonate (CaCO₃) nanocrystals have been examined for polymer/CaCO₃ thin-film composites synthesized through a self-organization process inspired by biomineralization. For the crystallization of CaCO₃, a thin-film matrix of chitosan has been used as a polymeric substrate. When the matrix is immersed into a supersaturated aqueous solution of CaCO₃ containing 1.4 × 10⁻³ wt % poly(aspartate) (PAsp), thin-film crystals of CaCO₃ are formed spontaneously. Three kinds of disklike films have been observed under a polarizing optical microscope. Electron diffraction analyses of each film have revealed that one is aragonite, displaying radial orientation of the c axes, and the others are vaterite, exhibiting different orientations. Detailed observation by scanning electron microscopy has clarified that these films are assemblies of crystalline particles 10–20 nm in size. The thin-film composites have been obtained over a PAsp concentration range of 4.4 × 10⁻⁴ to 1.0 × 10⁻² wt %. Vaterite formation becomes dominant when the concentration of PAsp is increased. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5153–5160, 2006     

Graft modification of chitosan,cellulose and alginate using reversible deactivation radical polymerization (RDRP)

This perspective covers the most recent literature on the graft-modification of the natural polymers celluloses, chitosan and alginate through reversible deactivation radical polymerization (NMP, ATRP and RAFT). The different routes to obtain well-defined polysaccharide-based hybrids including “grafting from” and “grafting to” approaches, and their applications as composite, stimuli-responsive, and biomaterials are discussed.     

Photovoltaic devices from CdSe nanocrystals and conjugated polymer composites

The preparation of CdSe nanospheres (ns-CdSe) and their application as electron acceptor in conjugated polymer photovoltaic devices are reported. ns-CdSe with diameters of 5 nm were prepared through an organometallic method. The transmission electron microscopy (TEM), ultraviolet-visible (UV-Vis) absorption and photoluminescence (PL) spectra indicate that the CdSe nanocrystals (NCs) are monodispersed nanospheres with the first exciton absorption peak at around 625 nm and the emission peak at around 652 nm. The PL spectra of the ns-CdSe/polymer composite films show that the PL of the conjugated polymers is effectively quenched upon the addition of ns-CdSe. Photovoltaic devices were fabricated from the composites of ns-CdSe and poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV) or poly(3-hexylthiophene) (P3HT). Under AM1.5 illumination (100 mW/cm²), the short circuit current (I _SC), open circuit voltage (V _OC), fill factor (FF) and energy conversion efficiency (η) reached 1.56 mA/cm², 0.75 V, 34.5% and 0.40%, respectively for device from the ns-CdSe/MEH-PPV (15: 1 by weight) and 1.93 mA/cm², 0.65 V, 38.4% and 0.48%, respectively for device from the ns-CdSe/P3HT (10: 1 by weight). __________ Translated from Chemical Journal of Chinese Universities, 2007, 28(3): 596–599 [译自: 高等学校化学学报]     

Chemical interactions and yellowing in chitosan-treated cellulose

The chemical interactions between cellulose and chitosan were studied in chitosan-treated celluloses using diffuse reflectance spectroscopic techniques (UV-Vis and FTIR) and fluorescence spectroscopy. The materials were obtained by treating pure cotton cellulose with chitosan in dilute acetic acid solutions of different concentration, and some samples were exposed to different thermal treatments in air. Other related materials, including cellulose treated with benzyl amine and chitosan-treated with acetaldehyde, were also prepared and studied as models for chitosan-treated celluloses. The spectra of the treated celluloses showed new absorption and emission bands that revealed the existence of chemical interactions. These bands were assigned to conjugated imines produced in the reaction of the chitosan amino groups with cellulose carbonyl groups. The reaction is strongly amplified at temperatures above 100 °C, causing the intense yellowing of chitosan-treated celluloses.     

In vitro biocompatibility of electrospun hexanoyl chitosan fibrous scaffolds towards human keratinocytes and fibroblasts

With the ability to form a submicron-sized fibrous structure with interconnected pores mimicking the extracellular matrix (ECM) for tissue formation, electrospinning was used to fabricate ultra-fine fiber mats of hexanoyl chitosan (H-chitosan) for potential use as skin tissue scaffolds. In the present communication, the in vitro biocompatibility of the electrospun fiber mats was evaluated. Indirect cytotoxicity evaluation of the fiber mats with mouse fibroblasts (L929) revealed that the materials were non-toxic and did not release substances harmful to living cells. The potential for use of the fiber mats as skin tissue scaffolds was further assessed in terms of the attachment and the proliferation of human keratinocytes (HaCaT) and human foreskin fibroblasts (HFF) that were seeded or cultured on the scaffolds at different times. The results showed that the electrospun fibrous scaffolds could support the attachment and the proliferation of both types of cells, especially for HaCaT. In addition, the cells cultured on the fibrous scaffolds exhibited normal cell shapes and integrated well with surrounding fibers. The obtained results confirmed the potential for use of the electrospun H-chitosan fiber mats as scaffolds for skin tissue engineering.     

In vitro biocompatibility of electrospun and solvent-cast chitosan substrata towards Schwann, osteoblast, keratinocyte and fibroblast cells

Chitosan or poly(N-acetyl-d-glucosamine-co-d-glucosamine) with a degree of deacetylation of about 85% was fabricated into nanofibrous membranes by electrospinning from 7% w/v chitosan solution in 70:30 v/v trifluoroacetic acid/dichloromethane solvent system. The obtained fibers were smooth without the presence of beads. The diameters of the individual fiber segments were 126 ± 20 nm. The potential for use of the electrospun chitosan nanofibrous membranes as substrates for cell/tissue culture was evaluated with four different cell types, i.e., Schwann cells, osteoblast-like cells, keratinocytes and fibroblasts, in terms of the attachment and the proliferation of the cells as well as the morphology of the seeded and the cultured cells. The results were compared with the corresponding solvent-cast films. Both types of the chitosan substrates supported the attachment and, at the same time, promoted the largest increase in the viability of the cultured keratinocytes. The viability of Schwann cells cultured on these substrates increased marginally well, but the attachment of the cells on the surfaces was relatively poor. Finally, both types of the chitosan substrates showed cytostatic property towards both osteoblast-like cells and fibroblasts, despite the convincingly good attachment of osteoblast-like cells on the surfaces.