Microstructure and electro-optical properties of sol–gel derived Cd-doped ZnO films

The microstructure, and the electrical and optical properties of undoped zinc oxide (ZnO) and cadmium-doped ZnO (CZO) films deposited by a sol–gel method have been investigated. The films have a polycrystalline structure with hexagonal wurtzite ZnO. Scanning electron microscopy (SEM) images indicated that the films have a wrinkle network with uniform size distributions. The elemental analyses of the CZO films were carried out by energy dispersive X-ray analysis. The fundamental absorption edge changed with doping. The optical band gap of the films decreased with Cd dopant. The optical constants of the films such as refractive index, extinction coefficient and dielectric constants changed with Cd dopant. A two-probe method was used to investigate the electrical properties, and the effect of Cd content on the electrical properties was investigated. The electrical conductivity of the films was improved by incorporation of Cd in the ZnO film.     

Structure and site selective luminescence of sol–gel derived Eu:Sr2SiO4

Strontium silicate (Sr₂SiO₄) samples doped with varying Eu³⁺content were prepared via sol–gel route and characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), dynamic light scattering (DLS) and photoluminescence (PL) techniques. The synthesis temperature could be brought down to 600 °C for formation of a singe phase sample. The concentration of the dopant ion and the temperature of annealing were optimized for maximum PL intensity. The critical energy-transfer distance for the Eu³⁺ ions was evaluated based on which the quenching mechanism was verified to be a multipole–multipole interaction. Based on the time-resolved emission data (TRES), it was inferred that, two different types of Eu³⁺ ions were present in the matrix. The first type was a long lived species (τ=4.7 ms) present at 10-coordinated ‘Sr’sites and the other was a short lived species (τ=1.2 ms) present at the 9-coordinated ‘Sr’sites which gets selectively excited at 296 nm. Judd–Ofelt (J–O) intensity parameters for both the species were evaluated. The trend observed for the two species in the J–O parameters, Ω₂ and Ω₄ were different confirming their existence in two different environments. The color coordinates of the system were evaluated and plotted on a CIE index diagram. Commercial utility of the phosphor was investigated by comparing it with commercial red phosphor.     

Structural and optical characterization of sol–gel derived Tm-doped BaTiO3 nanopowders and ceramics

Nanocrystalline Tm³⁺(5%)-doped BaTiO₃ (BT-Tm) has been synthesized by the sol–gel method. The morphology, structure, and optical properties of powders and ceramics were characterized. The average grain size of the gel precursor annealed at 700 and 900 °C was 20 nm and 30 nm, respectively. These powders were single phase and crystallized with a cubic structure while the BT-Tm sintered ceramics were crystallized with the tetragonal BaTiO₃ structure. The photoluminescence spectra showed typical transitions of Tm³⁺ ions and a structure consistent with the Tm³⁺ ions incorporation in the BaTiO₃ crystalline lattice. Thermoluminescence peaks recorded at 300 °C (for annealed samples) or at 230 °C for the ceramic sample were assigned to the recombination of the Tm²⁺-electron traps located mainly at the surface of the nano-crystals or inside the microcrystals, respectively.     

TEM characterization of organic nanocrystals grown in sol–gel thin films

The tetracene molecule (2,3-benzanthracene, C₈H₁₂) was used to synthesize nanocrystals grown in sol–gel thin films, ranging from 10 to 100 nm of diameter. This confined nucleation and growth was compared to microcrystallizations of the same molecule in free solution. Transmission electron microscopy (TEM) was used to characterize these two kinds of tetracene crystals. The observation was performed under low-dose illumination to avoid amorphization of the samples during electron irradiation. Spatial confinement and size distribution of micro- and nanocrystals were compared. Using electron microdiffraction and diffraction patterns simulations, we showed that free microcrystals and nanocrystals confined in gel glasses exhibit the same triclinic structure. In addition, time-resolved spectroscopy was used to record fluorescence decays, showing a monoexponential fluorescence decay for nanocrystals while microcrystals exhibit a multiexponential decay. The simple signature of nanocrystals luminescence is promising for the future development of chemical or biological sensors.     

Surface functionalisation of sol–gel derived aluminosilicates in simulated body fluids

Iron containing aluminosilicate systems obtained by sol–gel method are investigated as potential biomaterials for hyperthermia. The samples surface functionalisation in simulated body fluid enriched with bovine serum albumin (BSA) was studied by Fourier-transform infrared spectroscopy performed in reflectance mode and X-ray photoelectron spectroscopy (XPS). β-sheet/turns ratio estimated using the deconvolution of IR absorption band corresponding to amide I of adsorbed BSA on surface samples indicates a positive contribution to the biocompatibility of these materials. XPS results show an early attachment of albumin on sample surface that is weakly influenced by the protein concentration and prolonged immersion time in BSA–SBF solution.     

Structural studies and impedance spectroscopy of sol–gel derived Bi0.9Pr0.1FeO3 nanoceramics

Nano-crystalline Bi_0.9Pr_0.1FeO₃ (BPFO) ceramics have been synthesized by a sol–gel technique. The Rietveld refinement of the room temperature powder X-ray diffraction pattern confirms that the BPFO crystallizes in the rhombohedral R3c space group symmetry. SEM image of the sintered BPFO ceramic shows particles with same shape and fine grain morphology with the average grain size of 53±12 nm. The electrical properties of the ceramic are analysed by impedance spectroscopy. Grain and grain-boundary effect is observed in the material at lower temperature range which has been confirmed by electric modulus formalism. The ac conductivity spectrum obeys the Johnscher's power law. The activation energy calculated from dc conductivity is found to be 0.373 eV, which represents the conduction of small polaron over barrier between two sites of the lattice.     

Inverse magnetocaloric effect in sol–gel derived nanosized cobalt ferrite

The magnetocaloric properties of cobalt ferrite nanoparticles were investigated to evaluate the potential of these materials as magnetic refrigerants. Nanosized cobalt ferrites were synthesized by the method of sol–gel combustion. The nanoparticles were found to be spherical with an average crystallite size of 14 nm. The magnetic entropy change (ΔS _m) calculated indirectly from magnetization isotherms in the temperature region 170–320 K was found to be negative, signifying an inverse magnetocaloric effect in the nanoparticles. The magnitudes of the ΔS _m values were found to be larger when compared to the reported values in the literature for the corresponding ferrite materials in the nanoregime.     

Optical, electrical and morphological properties of p-type Mn-doped SnO2 nanostructured thin films prepared by sol–gel process

SnO₂ thin films doped with various manganese concentrations were prepared on glass substrates by sol–gel dip coating method. The decomposition procedure of compounds produced by alcoholysis reactions of tin and manganese chlorides was studied by thermogravimetric analysis (TGA). The effects of Mn doping on structural, morphological, electrical and optical properties of prepared films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), Hall effect measurement, Fourier Transform Infrared (FTIR) spectral analysis, UV–Vis spectrophotometry, and photoluminescence (PL) spectroscopy. The results of the X-ray diffraction show that the samples are crystalline with a tetragonal rutile structure and the grain size decreases with increasing the doping concentration. The SEM and AFM images demonstrate that the surface morphology of the films was affected from the manganese incorporation. The Sn_1?x Mn _x O₂ thin films exhibited electrically p-type behavior in doping level above x=0.035 and electrical resistivity increases with increase in Mn doping. The optical transmission spectra show a shift in the position of absorption edge towards higher wavelength (lower energy). The optical constants (refractive index and extinction coefficient) and the film thickness were determined by spectral transmittance and using a numerical approximation method. The oscillator and dispersion energies were calculated using the Wemple–DiDomenico dispersion model. The estimated optical band gap is found to decrease with higher manganese doping. The room-temperature PL measurements illustrate the decrease in intensity of the emission lines when content of Mn is increased in Mn-doped SnO₂ thin films.     

Large piezoelectric strain observed in sol–gel derived BZT–BCT ceramics

High performance lead (Pb)-free piezoelectric ceramics with excellent piezoelectric properties is in great demand for sensor and actuator applications. Barium zirconate titanate–barium calcium titanate [xBZT–(1 − x)BCT] (x = 0.5) is one such lead free system, which exhibits high piezoelectric properties similar to lead zirconate titanate (PZT). In this study we report the synthesis and characterization of this lead free [xBZT–(1 − x)BCT] (x = 0.5) via wet chemical sol–gel method. Calcination of the BZT–BCT precursor only at 1000 °C (against 1300 °C reported in the literature) for 4 h resulted in formation of single phase nanoparticles (<50 nm) as confirmed by X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies. Highly dense and homogenous microstructure with 95% of the theoretical density was obtained by solid-state sintering of the green pellets at 1550 °C. Remanent polarization (Pr) of 11.55 μC/cm² and relative permittivity of 20,020 at the Curie temperature of 95 °C were obtained. Electrically poled BZT–BCT ceramics samples exhibited high piezoelectric charge coefficients, d₃₃ ∼ 530 pC/N, d₃₃* ∼ 942 pm/V, large electromechanical coupling coefficient k_p ∼ 0.45 and a large strain of 0.15%, which are comparable to those of lead based piezoelectric ceramics. The excellent piezoelectric properties of this sol–gel derived BZT–BCT system has been analyzed and correlated to its structure in this report.     

Effects of annealing rate and morphology of sol–gel derived ZnO on the performance of inverted polymer solar cells

The effects of annealing rate and morphology of sol–gel derived zinc oxide(ZnO)thin films on the performance of inverted polymer solar cells(IPSCs)are investigated.ZnO films with different morphologies are prepared at different annealing rates and used as the electron transport layers in IPSCs.The undulating morphologies of ZnO films fabricated at annealing rates of 10 C/min and 3 C/min each possess a rougher surface than that of the ZnO film fabricated at a fast annealing rate of 50 C/min.The ZnO films are characterized by atomic force microscopy(AFM),optical transmittance measurements,and simulation.The results indicate that the ZnO film formed at 3 C/min possesses a good-quality contact area with the active layer.Combined with a moderate light-scattering,the resulting device shows a 16%improvement in power conversion efficiency compared with that of the rapidly annealed ZnO film device.     

Effect of the excimer laser irradiation on sol–gel derived tungsten–titanium dioxide thin films

A novel technique based on the excimer laser induced crystallization and modification of TiO₂ thin films is being reported. W⁺⁶ ions loaded TiO₂ (WTO) precursor films were prepared by a modified sol–gel method and spin-coated onto microscopic glass slides. Pulsed KrF (248 nm, 13 ns) excimer laser was used to irradiate the WTO amorphous films at various laser parameters. Mesoporous and nanostructured films consisting of anatase and rutile were obtained after laser irradiation at room temperature. The effect of varying W⁺⁶ ions concentrations on structural and optical properties the WTO films was analyzed by X-ray diffraction, field-emission scanning electron microscope, UV-Vis spectrophotometer and transmission electron microscope before and after laser treatment. Films irradiated for 10 pulses at 65–75 mJ/cm² laser fluence, exhibited anatase whereas higher parameters promoted the formation of rutile. XPS results revealed WO₃ along with minor proportion of WO₂ compounds after laser irradiation. Photo-absorbance of the WTO films was increased with increase in W⁺⁶ ions concentration in the film. TEM results exhibited a crystallite size of 15 nm which was confirmed from SEM results as well.     

Effect of calcination temperature on phase transformation,structural and optical properties of sol–gel derived ZrO2 nanostructures

Zirconia (ZrO₂) nanostructures of various sizes have been synthesized using sol–gel method followed by calcination of the samples from 500 to 700 °C. The calcined ZrO₂ powder samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier-transform infra-red spectroscopy (FT-IR), UV–visible spectroscopy (UV–vis.), Raman spectroscopy (RS) and thermogravimetric analysis (TGA). The phase transformation from tetragonal (t) to monoclinic (m) was observed. The average diameter of the ZrO₂ nanostructures calcined at 500, 600 and 700 °C was calculated to be 8, 17 and 10 nm, respectively. The ZrO₂ sample calcined at 500 °C with tetragonal phase shows a direct optical band gap of 5.1 eV. The value of optical band gap is decreased to 4.3 eV for the ZrO₂ calcined at 600 °C, which contains both tetragonal (73%) and monoclinic (27%) phases. On further calcination at 700 °C, where the ZrO₂ nanostructures have 36% tetragonal and 64% monoclinic phases, the optical band gap is calculated to be 4.8 eV. The enhancement in optical band gap for ZrO₂ calcined at 700 °C may be due to the rod like shape of ZrO₂ nanostructures. The tetragonal to monoclinic phase transformation was also confirmed by analyzing Raman spectroscopic data. The TG analysis revealed that the ZrO₂ nanostructure with dominance of monoclinic phase is found to be more stable over the tetragonal phase. In order to confirm the phase stability of the two phases of ZrO₂, single point energy is calculated corresponding to its monoclinic and tetragonal structures using density functional theory (DFT) calculations. The results obtained by theoretical calculations are in good agreement with the experimental findings.     

Spectroscopic properties of Co2+: ZnAl2O4 nanocrystals in sol–gel derived glass–ceramics

Transparent glass–ceramics containing zinc–aluminum spinel (ZnAl₂O₄) nanocrystals doped with tetrahedrally coordinated Co²⁺ ions were obtained by the sol–gel method for the first time. The gels of composition SiO₂–Al₂O₃–ZnO–CoO were prepared at room temperature and heat-treated at temperature ranging 800–950 °C. When the gel samples were heated up to 900 °C, ZnAl₂O₄ nanocrystals were precipitated. Co²⁺ ions were located in tetrahedral sites in ZnAl₂O₄ nanocrystals. X-ray diffraction analysis shows that the crystallite sizes of ZnAl₂O₄ crystal become large with the heat-treatment temperature and time, and the crystallite diameter is in the range of 10–15 nm. The dependence of the absorption and emission spectra of the samples on heat-treatment temperature were presented. The difference in the luminescence between Co²⁺ doped glass–ceramic and Co²⁺ doped bulk crystal was analysed. The crystal field parameter D_q of 423 cm⁻¹ and the Racah parameters B of 773 cm⁻¹ and C of 3478.5 cm⁻¹ were calculated for tetrahedral Co²⁺ ions.     

Effect of dopants on the structural,optical and electrical properties of sol–gel derived ZnO semiconductor thin films

Undoped, Ga-, In-, Zr-, and Sn-doped ZnO transparent semiconductor thin films were deposited on alkali-free glasses by sol–gel method. 2-methoxyethanol (2-ME) and diethanolamine (DEA) were chosen as a solvent and a stabilizer, respectively. The doping concentration was maintained at 2 at.% in the impurity doping precursor solutions. The effects of different dopants on the structural, optical, and electrical properties of ZnO thin films were investigated. XRD results show that all annealed ZnO-based thin films had a hexagonal (wurtzite) structure. ZnO thin films doped with impurity elements obviously improved the surface flatness and enhanced the optical transmittance. All impurity doped ZnO thin films showed high transparency in the visible range (>91%). The Ga- and In- doped ZnO thin films exhibited higher Hall mobility and lower resistivity than did the undoped ZnO thin film.     

Growth of vertically aligned one-dimensional ZnO nanowire arrays on sol–gel derived ZnO thin films

Vertically aligned one-dimensional ZnO nanowire arrays have been synthesized by a hydrothermal method on sol–gel derived ZnO films. Sol–gel derived ZnO films and corresponding ZnO nanowire arrays have been characterized by X-ray diffraction and field-emission scanning electron microscopy. The effect of sol–gel derived ZnO film surface on the morphology of ZnO nanowire arrays has been investigated. The authors suggest from our investigation that sol–gel derived ZnO films affect the growth of one-dimensional ZnO nanostructures. Not only crystalline ZnO films but also amorphous ones can act as a scaffold for ZnO nucleus. Tilted ZnO micro-rods are grown on ZnO gel films, whereas vertically aligned ZnO nanowire arrays are grown on nanometer-sized ZnO grains. The average diameter of ZnO nanowire arrays are correlated strongly with the grain size of sol–gel derived ZnO films.     

Luminescent features of sol–gel derived rare-earth multi-doped oxyfluoride nano-structured phosphors for white LED application

Rare-earth doped oxyfluoride 75SiO₂:25PbF₂ nano-structured phosphors for white-light-emitting diodes were synthesized by thermal treatment of precursor sol–gel derived glasses. Room temperature luminescence features of Eu³⁺, Sm³⁺, Tb³⁺, Eu³⁺/Tb³⁺, and Sm³⁺/Tb³⁺ ions incorporated into low-phonon-energy PbF₂ nanocrystals dispersed in the aluminosilicate glass matrix and excited with UV light emitting diode were investigated. The luminescence spectra exhibited strong emission signals in the red (600, 610, 625, and 646 nm), green (548 and 560 nm), and blue (485 nm) wavelength regions. White-light emission was observed in Sm/Tb and Eu/Tb double-doped activated phosphors employing UV-LED excitation at 395 nm. The dependence of the luminescence emission intensities upon annealing temperature and rare-earth concentration was also examined. The results indicated that there exist optimum annealing temperature and activator ion concentration in order to obtain intense visible emission light with high color rendering index. The study suggests that the nanocomposite phosphor based upon 75SiO₂:25PbF₂ host herein reported is a promising contender for white-light LED applications.     

Evolution of ZnO nanostructures in sol–gel synthesis

Evolution of the microstructure and optical properties of ZnO nanoparticles in a mild sol–gel synthesis process is studied. The ZnO nanostructures were prepared by reacting zinc acetate dihydrate with NaOH in water at 50−60 °C. Evolution of ZnO nanostructures with reaction time is studied using UV–Vis spectroscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD), and Fourier transform infrared (FT-IR) spectroscopy techniques. During the process of Zn²⁺ hydroxylation, well defined rod-like crystals were formed within 15 min. Further hydroxylation leads to the formation of a gel-like structure within about 45 min. However, XRD, FT-IR and energy dispersive spectroscopy (EDS) confirmed that these initial products were zinc hydroxyl double salts (Zn-HDS), not ZnO. On ageing the reaction mixture, ZnO nanoparticles with wurtzite structure evolved.     

Structural,electrical and optical properties of sol–gel AZO thin films

Transparent conductive Al-doped zinc oxide (AZO) thin films were prepared by a sol–gel method and their structural, electrical and optical properties were systematically investigated. A minimum resistivity of 4.2 × 10⁻³ Ω cm was obtained for the 650 °C-annealed films doped with 1.0 at.% Al. All films had the preferential c-axis oriented texture according to the X-ray diffraction (XRD) results. Optical transmittance spectra of the films showed a high transmittance of over 85% in the visible region and the optical band gap of the AZO films broadened with increasing doping concentration.