Application of the Swimming Pool Backwash Water Recovery System with the Use of Filter Tubes

During the operation of swimming pools, large losses of water from the backwash of swimming pool filters are observed. This water is often discharged into sewers or used to sprinkle sports grounds. The aim of the research was to design and build an installation for purification and recovery of backwash water (BWW). It consists of flocculation, pre-filtration, and ultrafiltration based on filter tubes and ozone disinfection. Backwash water treatment installation contributes to purification and improvement of water quality. The effectiveness of the removal of microbial contamination with the use of the system was over 99%. The high efficiency of removing physicochemical impurities was also achieved. Water turbidity was reduced from 96.9 NTU to 0.13 NTU. After using the system, the oxidability of water decreased from 6.26 mg O₂∙dm⁻³ to 0.4 mg O₂∙dm⁻³. When using the system, a reduction of total organic carbon by 80% was also noticed. After the treatment process, water meets the strict criteria and can be returned to the pool system of water as fresh water with parameters of supply water—directly to the overflow tank. It has been shown that up to 96% of water can be recovered with the technology. The cost comparison showed annual savings of over EUR 9000.     

Photocatalytic Decomposition of Acetaldehyde with Anatase Nanocrystals-Dispersed Silica Films Prepared by the Sol-Gel Process with Hot Water Treatment

Anatase nanocrystals of 5 to 10 nm in diameter were formed in the silica-titania films by treatment with hot water. The formation of nanocrystals with hot water treatment was a unique phenomenon to the silica-titania system and the addition of organic polymers such as PEG was indispensable for the high dispersion of anatase nanocrystals in the films. The hydrolysis of Si—O—Ti bonds with hot water was considered to play an important role for the formation of anatase nanocrystals. The resultant films were transparent even after the formation of anatase nanocrystals. Acetaldehyde was photocatalytically decomposed into CO₂ on the films which were subjected to a hot water treatment. The amounts of generated CO₂ were twice of that of introduced acetaldehyde, indicating that the total acetaldehyde was completely decomposed to CO₂. Anatase nanocrystals-dispersed films can be formed on various kinds of substrates including those with poor heat resistance such as organic polymers and organisms by this process, so that the substrates coated with the films are expected to be widely used for photocatalytic applications.     

Proficiency tests for pharmaceuticals in different waters

To date there are no German or international standards for the analysis of pharmaceuticals in waters. The efficiency of the analytical methods—predominantly LC-MS/MS and GC-MS—used for trace analysis of pharmaceuticals is proved for the first time by proficiency tests using natural waters.Two proficiency tests for up to 11 different groups of pharmaceuticals in river water and waste water were carried out in 2000 (28 participants) and 2002 (20 participants). The spiking concentrations were 60–800 ng/L for surface water and 80–1280 ng/L for waste water. For most determinants good recovery rates (80–120%) and variations (around 35% for surface water and 50% for waste water) were reported.     

Mercury depth profiles in river and marine sediments measured by the diffusive gradients in thin films technique with two different specific resins

The diffusive gradients in thin films technique (DGT) was used to measure depth profiles of mercury in river and marine sediments in situ to a spatial resolution of 0.5 cm. Agarose gel was used as the diffusive gel in the DGT probes. Two different selective resins—Chelex 100 with iminodiacetic groups and Spheron-Thiol with thiol groups incorporated in the polyacrylamide resin gel—were tested. The different capture efficiencies of the two adsorbents enabled the fractions of mercury bound in different species in sediment pore water to be estimated. Mercury concentrations obtained by DGT with Spheron-Thiol resin were very similar to those obtained after centrifugation. This indicates that DGT with Sheron-Thiol resin reports on total dissolved mercury levels. The concentration of mercury measured by DGT with Chelex-100 resin was much lower (by a factor of 5–20) for the same sediment samples. Chelex-100 does not have such a high affinity to mercury as Spheron-Thiol, and so it only reports on the content of labile mercury species, such as inorganic ions and weak complexes. The content of labile mercury species in the river sediment was approximately 20% of the total dissolved mercury in pore water, whereas in marine sediment only 7% of the mercury was present as labile species.     

Determination of differences in free and bound water contents of beef muscle by DSC under various freezing conditions

The differences in bound water content of beef semimembranous muscle samples obtained from previously chilled (24 h at +4°C) middle-aged beef carcasses were determined by the use of DSC. Initially, samples obtained from fresh, unprocessed meat were frozen at –40, –50 or –65°C to determine their melting peaks for freezable water (free water) content with the use of DSC. The samples were then subjected to an environment with an ambient temperature of –30, –35, –40 or –45°C, with no air circulation, or with an air circulation speed of 2 m s^–1, until a thermal core temperature of –18°C was attained; this was followed by thawing the samples until a thermal core temperature of 0°C was reached. This process was followed by subjecting the samples to the ambient temperatures mentioned above, to accomplish complete freezing and thawing of the samples, with DSC, and thereby determination of the freezable water contents, which were then used to determine the peaks of melting. The calculated peak areas were divided by the latent heat of melting for pure water, to determine the freezable water contents of the samples. The percentage freezable water content of each sample was determined by dividing its freezable water content by its total water content; and the bound water content of each sample was determined by subtracting the percentage free water content from the total. In view of the fact that the free water content of a sample is completely in the frozen phase at temperatures of –40°C and below, the calculations of free and bound water contents of the samples were based on the averages of values obtained at three different temperatures.     

Hydride-trapping techniques for the speciation of arsenic

The determination of arsenic species by the trapping of volatile hydrides prior to atomization in the light path of an atomic absorption spectrometer is described and its operation in the measurement of arsenic species in the marine environment are discussed. Examples are drawn from the analysis of Tamar estuary water and sediment interstitial (pore) waters and from studies of the temporal variation of dimethylarsenic in coastal waters. Improvements in both the design and operation of the technique have resulted in enhanced performance. Baseline resolution of inorganic arsenic, monomethylarsenic and dimethylarsenic is now possible and trimethylarsine is resolved. Ultraviolet photolysis of arsenobetaine and arsenocholine gives partial conversion to trimethylarsine oxide. This can be employed in the qualitative appraisal of the presence of trimethylarsenic species. Current detection limits (3 sigma) for inorganic, mono- and di-methylarsenic lie in the range 19 to 61 pg absolute, giving 19–61 ng/1 concentration detection limits for 1 ml samples. This can be improved even further by using larger sample volumes. The properties of the analysis system when presented with various arsenic species are described. A ca. 10% loss of arsenite occurs in samples stored at —20 °C and immediate freezing of samples in liquid nitrogen is recommended.     

The Role of 2-(Methacryloyloxy) Ethyl Acetoacetate in the Polymerization of Hybrid Multicomponent (Si, Ti, Zr) Sols

2-(Methacryloyloxy) ethylacetoacetate (MEEAH) was used as stabilyzing agent to control the chemical reactivity of Ti and Zr monomeric alkoxides in a Si—Ti—Zr sol. The organic and inorganic polymerizations were carried out simultaneously. The organic polymerization was performed using benzoyl peroxide as the initiator. The inorganic polymerization was done via the sol-gel process. The polymerization was studied by several spectroscopic techniques, including Fourier Transform Infrared (FTIR), UV-Vis, ²⁹Si NMR, Small Angle X-ray Scattering (SAXS) and X-ray diffraction (XRD). Theoretical calculation and experimental results showed that MEEAH acted as a monodentate ligand, mainly. This led to a high condensation extent of the Si species in the sol. A short range order gel was obtained, according to the SAXS results. The Si—O—Ti and Si—O—Zr bonds were detected by FTIR. The bonds remained stable, because a sample calcined at 1173 K was amorphous according to the XRD results, indicating structural homogeneity.     

Change in the state of aluminum in heat-and-water vapor dealumination of Y zeolite based on the IR spectrum of framework vibrations

The effect of heat treatment of dealuminated samples of Y zeolite in water vapors and in air on the state of the aluminum in the composition of six-coordinated compounds, Al^VI, O, was investigated by IR Fourier spectroscopy. The existence of at least two crystal chemically different Al^VI, O compounds which act differently to the effect of acids: weakly bound with the framework — out-of-framework, and covalently bound with the framework oxygen — in-framework, and the ratio between them changes with an increase in the temperature of treatment in water vapors toward an increase in the concentration of out-of-framework aluminum compounds, and in heat treatment in air, toward in-framework aluminum compounds.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 6, pp. 1299–1303, June, 1991.     

Determination of mercury species in natural waters at picogram level with on-line RP C18 preconcentration and HPLC-UV-PCO-CVAAS

A new technique has been developed for the determination of methyl-, ethyl-, methoxyethyl-, ethoxyethyl-, phenyl- and inorganic mercury in natural water samples. The mercury compounds have been complexed for the preconcentration on RP C18 columns by sodium pyrrolidinedithiocarbamate (SPDC), sodium diethyldithiocarbamate (SDDC) and hexamethyleneammonium (HMA) — hexamethylenedithiocarbamate (HMDC), separated by HPLC and determined by UV-PCO-CVAAS (ultra violet, post column oxidation, cold vapour atomic absorption spectrometry). The standard deviations are in the range of 6.9 to 11.8%. The recoveries amount to 86%, 78%, 88%, 83%, 79% and 84% for methyl-, ethyl-, methoxyethyl-, ethoxyethyl-, phenyl- and inorganic mercury for the enrichment from 300 ml water samples. The detection limit for methyl mercury is 0.5 ppt. This new on-line preconcentration procedure has been tested with rain, drinking, surface and process water samples.     

聚硅酸铝在水处理过程中絮凝热效应的研究

用SRC-100溶解―反应量热计测定了聚硅酸铝在水处理过程中的絮凝焓变,利用均匀设计法分析了不同因素对结果的影响。结果表明:絮凝焓变随水样浊度的增加而增大,随铝/硅摩尔比的增加先增大(0～0.7)后减小(0.7～1.6);聚硅酸铝用量与水样浊度、pH值与水样浊度在焓变较小时交互作用较大;聚硅酸铝用量与pH值的相互作用在强碱性条件下随焓变增大而增强。絮凝进行的过程推动力为聚硅酸铝在水中的溶解稀释焓变。     

On the Existence and Hydrolytic Stability of Titanosiloxane Bonds in the System: Glycidoxypropyltrimethoxysilane-Water-Titaniumtetraethoxide

Heterometal materials based on glycidoxypropyltrialkoxysilane and titaniumalkoxide are used for optical applications and require a high homogeneity on the molecular level. The presence of heterometal titanosiloxanes, their distribution and hydrolytic stability should influence the homogeneity of these materials. 29Si and 17O NMR spectroscopy has been used to investigate sols with molar ratios Si : Ti = 1 and H2O : OR (H) = 0.5 – 2.0 and their gels after heat treatment at 130°C. The presence of Si—O—Ti bonds in sols with a low water content (H < 0.2) and in the corresponding gels was identified by the high-field shift of the 29Si NMR signals of T1 and T2 units of up to 2–3 ppm compared to corresponding signals of homo-condensed Si—O—Si bonds. The existence of Si—O—Ti bonds in the sols is supported by 17O NMR spectra which show a characteristic signal around 340 ppm. A cleavage of the Si—O—Ti bonds occurs with increasing water/OR ratio in the sols. The cleavage of the heterometal bonds and the building up of homo-condensed species leads to a separation into areas with predominantly Ti—O—Ti and Si—O—Si bonds resulting in a decreased molecular homogeneity of the materials.     

Electron-microscope investigation of polish sandomir silicas

Summary Silica was examined under the electron microscope —directly by transmission and indirectly in the form of carbon replicas — and the change in structure resulting from alkaline treatment was examined. It was found that the original silica has a larnellar structure with marked surface relief. After treatment with alkali and washing with water, its surface becomes covered with round particles about 100–200 A in size, a phenomenon which results from the hydrolysis of, alkali silicate and separation of colloidal silicon dioxide.     

The mechanism and stability of thermal transitions in hair keratin

Differential Scanning Calorimetry (DSC) has been applied to study the interactions between components of human hair keratin. Keratin is a biopolymeric composite made of several proteins forming basically two phases: amorphous matrix and crystalline microfibrillar phase. Water, the content of which depends on atmospheric humidity, is also an integral part of keratin structure. The following processes are apparent from the DSC: removal of loosely bound water (ca. 70°C), a transition in the amorphous phase (155°C) and melting/denaturation of the -crystalline phase (233°C). The process occurring in keratin at ca. 155°C has an opposite character to a glass transition; we refer to this process as the toughening transition. The area of the -keratin peak increases significantly upon annealing at temperatures from 80°C to 150°C and decreases for higher annealing temperatures. Water affects both the crystalline and amorphous phases of keratin. The process similar in nature to annealing — induced recrystallization in synthetic polymers is strictly correlated with removal of strongly bound fraction of water in keratin.     

Efficient Degradation of Iopromide by Using Sulfite Activated with Mackinawite

Iopromide (IOP), an iodinated X-ray contrast medium (ICM), is identified as a precursor to iodide disinfection byproducts that have high genotoxicity and cytotoxicity to mammals. ICM remains persistent through typical wastewater treatment processes and even through some hydroxyl radical-based advanced oxidation processes. The development of new technologies to remove ICMs is needed. In this work, mackinawite (FeS)-activated sulfite autoxidation was employed for the degradation of IOP-containing water. The experiment was performed in a 500 mL self-made temperature-controlled reactor with online monitoring pH and dissolved oxygen in the laboratory. The effects of various parameters, such as initial pH values, sulfite dosages, FeS dosages, dissolved oxygen, and inorganic anions on the performance of the treatment process have been investigated. Eighty percent of IOP could be degraded in 15 min with 1 g L⁻¹ FeS, 400 μmol L⁻¹ sulfite at pH 8, and high efficiency on the removal of total organic carbon (TOC) was achieved, which is 71.8% via a reaction for 1 h. The generated hydroxyl and oxysulfur radicals, which contributed to the oxidation process, were identified through radical quenching experiments. The dissolved oxygen was essential for the degradation of IOP. The presence of Cl⁻ could facilitate IOP degradation, while NO₃⁻ and CO₃²⁻ could inhibit the degradation process. The reaction pathway involving H-abstraction and oxidative decarboxylation was proposed, based on product identification. The current system shows good applicability for the degradation of IOP and may help in developing a new approach for the treatment of ICM-containing water.     

Application of Inductively Coupled Plasma Spectrometric Techniques and Multivariate Statistical Analysis in the Hydrogeochemical Profiling of Caves—Case Study Cloșani,Romania

The aim of the study was to develop the hydrogeochemical profiling of caves based on the elemental composition of water and silty soil samples and a multivariate statistical analysis. Major and trace elements, including rare earths, were determined in the water and soil samples. The general characteristics of water, anions content, inorganic and organic carbon fractions and nitrogen species (NO₃⁻ and NH₄⁺) were also considered. The ANOVA—principal component analysis (PCA) and two-way joining analysis were applied on samples collected from Cloșani Cave, Romania. The ANOVA-PCA revealed that the hydrogeochemical characteristics of Ca²⁺-HCO₃⁻ water facies were described by five factors, the strongest being associated with water-carbonate rock interactions and the occurrence of Ca, Mg and HCO₃⁻ (43.4%). Although organic carbon fractions have a lower influence (20.1%) than inorganic ones on water characteristics, they are involved in the chemical processes of nitrogen and of the elements involved in redox processes (Fe, Mn, Cr and Sn). The seasonal variability of water characteristics, especially during the spring, was observed. The variability of silty soil samples was described by four principal components, the strongest influence being attributed to rare earth elements (52.2%). The ANOVA-PCA provided deeper information compared to Gibbs and Piper diagrams and the correlation analysis.     

The Role of Sulphate and Phosphate Ions in the Recovery of Benzoic Acid Self-Enhanced Ozonation in Water Containing Bromides

The ozonation of aromatic compounds in low-pH water is ineffective. In an acidic environment, the decomposition of ozone into hydroxyl radicals is limited and insufficient for the degradation of organic pollutants. Radical processes are also strongly inhibited by halogen ions present in the reaction medium, especially at low pH. It was shown that even under such unfavorable conditions, some compounds can initiate radical chain reactions leading to the formation of hydroxyl radicals, thus accelerating the ozonation process, which is referred to as so-called “self-enhanced ozonation”. This paper presents the effect of bromides on “self-enhanced ozonation” of benzoic acid (BA) at pH 2.5. It is the first report to fully and quantitatively describe this process. The presence of only 15 µM bromides in water inhibits ozone decomposition and completely blocks BA degradation. However, the effectiveness of this process can be regained by ozonation in the presence of phosphates or sulphate. The addition of these inorganic salts to the bromide-containing solution helps to recover ozone decomposition and BA degradation efficiency. As part of this research, the fractions of hydroxyl, sulphate and phosphate radicals reacting with benzoic acid and bromides were calculated.     

Correlations between bond lengths and stretching frequencies in the O—D...O hydrogen bridge and their consequences

Based on modern neutron diffraction data and the known empirical correlations between the geometric and spectroscopic parameters of hydrogen bonds, the analytical expression describing the relation between the O—D covalent and D...O hydrogen bond lengths in the O—D...O hydrogen bridge was obtained. The distribution functions of the interatomic and nearest intermolecular distances in heavy water were calculated from the Raman band shapes in the 10 to 90 °C temperature interval in the framework of the fluctuation theory of hydrogen bonding.     

Quaternary benzophenanthridine alkaloids 9,10-demethylene derivatives of sanguinarine

Summary In the isolation and purification of the benzophanthridine alkaloids sanguinarine and chelerythrine two minor bases — 9,10-demethylenesanguinarine and 9,10-demethylene-9,10-dehydrosanguinarine — were isolated, and it was shown that the former is an artefact produced from sanguinarine in the process of isolation and also when the sulfates of the alkaloids are subjected to prolonged storage.Translated from Khimiya Prirodnykh Soedinenii, No. 6, pp. 764–767, November-December, 1978. Original article submitted August 10, 1978.     

Thermal Analysis of Casein

Case in was analyzed during thermal treatment and pyrolysis. The thermal degradation process of casein was interpreted and thermostability indices, rate, order and activation energy of thermode-structive reaction of casein were determined on the basis of thermogravimetric analysis. The thermodestruction of casein has the characteristics of a first order reaction with activation energy E _a=3.87 kcal mol^–1 (16.2 kJ mol^–1).The pyrolysis of casein was investigated and we determined optimal heating temperature — 550°C and yields of biochar, pitch, pyrolysis water and gases.This revised version was published online in November 2005 with corrections to the Cover Date.