Analysis of amino acids by capillary zone electrophoresis with electrochemical detection

The precapillary derivatization of 20 amino acids with naphthalene-2,3-dicarboxaldehyde (NDA) and CN(-) was investigated. All these derivatized amino acids could be oxidized on the carbon fiber microdisk bundle electrode except proline. Capillary zone electrophoresis with electrochemical detection was employed for the analysis of 19 amino acids. The optimum conditions of separation and detection were borate, pH 9.48, for the electrolyte, 18 kV for the separation voltage and 1.15 V versus a saturated calomel electrode for the detection potential. Limits of detection of concentration or mass for individual amino acids were between 1.7 x 10(-7) and 1.8 x 10(-6) mol/L or 84 and 893 amol (according to the signal-to-noise ratio of 3) for the injection voltage of 6 kV and injection time of 10 s. The relative standard deviations were between 0.80 and 2.3% for the migration times and 1.4 and 6.4% for the electrophoretic peak currents. From a mixture of 19 amino acids, 10 amino acids (Arg, Lys, Orn, Try, Ser, Ala, Gly, Cys, Glu, Asp) could be well separated. The other 9 amino acids appeared on three electrophoretic peaks. From the samples, in which the nine amino acids do not exist simultaneously, some of them could also be detected. The method was applied to the determination of amino acids in beer by the standard addition method. The recovery for the amino acids in beer was 91-109%.     

中药菟丝子中生物活性成分的毛细管电泳-电化学检测

采用毛细管电泳-电化学检测法(CE-ECD)同时测定了菟丝子中芦丁、金丝桃甙、山柰酚、对香豆酸和槲皮素等5种主要生物活性成分的含量,考察了运行缓冲液酸度和浓度、分离电压、氧化电位和进样时间等实验参数对分离检测的影响。在最佳实验条件下,以直径300 μm的碳圆盘电极为工作电极,检测电位为+950 mV(vs. 参比电极),以50 mmol/L的硼砂缓冲溶液(pH 9.0)为运行缓冲液,上述各组分在19 min内能完全分离。芦丁、金丝桃甙、山柰酚、对香豆酸和槲皮素在两个数量级的范围内呈良好线性关系,检测下限(按S/N=3计) 分别为1.93×10-5,3.55×10-4,3.65×10-5,1.73×10-5和1.46×10-4 g/L。该法已成功地应用于菟丝子中活性成分的分离检测,结果令人满意。     

Study of the separation and determination of monosaccharides in soluble coffee by capillary zone electrophoresis with electrochemical detection

A simple, fast and reliable method, based on capillary electrophoresis with electrochemical detection, for the separation and determination of six monosaccharides, namely glucose, galactose, arabinose, fructose, xylose and ribose, in soluble coffees was developed. A copper disk electrode was used as the working electrode. The optimum conditions for separation and detection were 50 mmol L-1 sodium hydroxide buffer (pH 12.7), separation voltage 5 kV and detection potential 0.65 V (vs. Ag/AgCl). The linear ranges were from 5.0 x 10(-3) to 0.5 mmol L-1 for all six sugars. All regression coefficients were > 0.99. The detection limits for all the sugars were 1.0 x 10(-3) mmol L-1. The RSD of the peak current was < 4.2% (n = 5). The proposed method was applied directly to the separation and determination of the six sugars without prior derivatization, and the assay results were satisfactory.     

毛细管电泳-电化学检测法测定硫酸铜-维生素C反应体系中的羟基自由基和菊花的抗氧化活性

采用毛细管电泳-电化学检测方法,以对羟基苯甲酸为自由基捕捉剂,测定了硫酸铜-维生素C反应体系(pH 7.4)中生成的羟基自由基。研究了电极电位、运行液的pH值、电泳电压及进样时间对体系中反应物和产物分离的影响,得到了最优化的测定条件;讨论了体系中各反应物浓度和反应时间对产物浓度的影响。以直径为300 μm的碳圆盘电极为检测电极,工作电极电位为0.95 V(vs.SCE),目标产物3,4-二羟基苯甲酸在1.5×10-4~6.0×10-6 mol/L范围内线性关系良好,检测限（S/N=3）为1.5×10-6 mol/L。应用该方法,研究测定了不同品种菊花的抗氧化活性。     

Nafion-离子液体-修饰碳糊电极在抗坏血酸和尿酸存在下选择性测定多巴胺

用Nafion和亲水性离子液体溴化1-辛基-3-甲基咪唑([OMIM]Br)作修饰剂制作了Nafion-离子液体-修饰碳糊电极;在0.1 mol/L磷酸盐缓冲溶液(pH 7.40)中,用循环伏安法(CV)和方波伏安法(SWV)研究了多巴胺在该修饰电极上的电化学行为,建立了抗坏血酸和尿酸存在下选择性测定多巴胺的新方法.研究表明,该修饰电极降低了多巴胺氧化、还原反应的过电位,增大了其氧化、还原反应的峰电流,而抗坏血酸和尿酸在该修饰电极上无响应;在方波伏安曲线上,多巴胺的氧化电流与其浓度在3.0×10-8～2.0×10-6 mol/L范围内呈线性关系,检出限为1.0×10-8 mol/L.该法可用于注射液和模拟生物样品中多巴胺的测定.     

Detection of neuropeptides using on-capillary copper complexation and capillary electrophoresis with electrochemical detection

Capillary electrophoresis with electrochemical detection using a carbon fiber electrode in conjunction with on-capillary copper complexation was evaluated for the determination of peptides in standard and biological matrices. Peptides composed of 2-10 amino acids were investigated. A comparison was made between the responses obtained for peptides containing the oxidizable residue tyrosine and those obtained for their respective copper complexes. Electrochemical detection of non-tyrosine-containing peptides and a cyclic peptide was also demonstrated. A separation of leucine (Leu)-enkephalin and five metabolites was developed and then used for the investigation of Leu-enkephalin metabolism in plasma. The appearance of the des-tyrosine (des-Tyr) Leu-enkephalin, which cannot be detected directly at a carbon electrode, was monitored using the on-capillary complexation technique. Direct injection of the plasma sample was possible using this methodology.     

Simultaneous determination of aminothiols, ascorbic acid and uric acid in biological samples by capillary electrophoresis with electrochemical detection

A method based on capillary electrophoresis with electrochemical detection has been employed for the separation and determination of homocysteine, cysteine, reduced glutathione, ascorbic acid and uric acid. Effects of several important factors such as the acidity and concentration of the running buffer, separation voltage, injection time and detection potential were investigated to acquire the optimum conditions. The detection electrode was a 500 microm diameter platinum disk electrode at a working potential of +1.05 V (vs saturated calomel electrode). The five analytes were well separated within 10 min in a 50 cm long fused silica capillary at a separation voltage of 18 kV in a 100 mm phosphate buffer (pH 7.8). The relation between peak current and analyte concentration was linear over about 3 orders of magnitude with the detection limits (S/N = 3) ranging from 0.83 to 2.58 microm. The proposed method was successfully applied to determine cysteine, reduced glutathione, ascorbic acid and uric acid in human whole blood and rat brain tissues with satisfactory assay results and should find a wide range of bioanalytical applications.     

Direct electrochemical determination of pyruvate in human sweat by capillary zone electrophoresis.

Capillary zone electrophoresis was employed for the determination of pyruvate in human sweat using electrochemical detection with a carbon fiber microdisk bundle electrode at a constant potential of 1.60 V vs. saturated calomel electrode. The optimum separation conditions are 3.6 x 10(-3) mol/L Na2HPO4-1.4 x 10(-3) mol/L NaH2PO4 (pH 7.2) for the buffer solution, and 18 kV for the separation voltage. The limits of detection of pyruvate are 8.0 x 10(-6) mol/L or 24 fmol (S/N = 3) for the injection voltage of 6 kV and the injection time of 10 s. The relative standard deviation is 2.0% for the migration time and 5.7% for the electrophoretic peak current. The method was applied to determining pyruvate in human sweat.     

A new method of quantification of pipemidic-acid by capillary zone electrophoresis with end-column amperometric detection

Capillary zone electrophoresis was employed for the determination of pipemidic acid using an end-column amperometric detection with a carbon fiber microdisk array electrode, at a constant potential of -1.10 V vs. saturated calomel electrode. The optimum conditions of separation and detection were 1.2 x 10(-4) mol/LNaOAc - 8.8 x 10(-4) mol/ LHOAc for the buffer solution, 20 kV for the separation voltage, 5 kV and 10 s for the injection voltage and the injection time. The limit of detection was 1.05 x 10(-7) mol/L or 189 amol (S/N=3). The relative standard deviation was 0.31% for the migration time and 2.0% for the electrophoretic peak current. The method was applied to determining pipemidic acid in human serum.     

Capillary electrophoresis of some tetracycline antibiotics coupled with reductive fast cyclic voltammetric detection.

The separation and quantitative performance parameters for tetracycline, chlortetracycline and oxytetracycline antibiotics were investigated by capillary zone electrophoresis coupled with fast cyclic voltammetric detection. Optimization of pH and complexation with a boric acid-sodium tetraborate buffer provided good resolution of all compounds. Detection by electrochemical reduction using fast on-line cyclic voltammetric detection with a Hg-film-microm electrode gave detection limits (2 x peak-to-peak baseline noise) of 7 x 10(-7) mol/l for tetracycline and chlortetracycline, and 1.5 x 10(-6) mol/l for oxytetracycline. The influence of electrode material, potential range and scan rate was examined and discussed. Optimal electrochemical detection was obtained at a Hg-film electrode with a waveform that consisted of an initial constant potential of -0.6 V for 200 ms followed by a cyclic voltammetry (CV) scan at 300 V/s from - 0.6 V to a vertex potential of 1.7 V. The analytical signal was obtained by plotting the integrated values of the CV current from each applied waveform as a function of time. The calibration plot (peak areas) for each separated peak was found to be linear over three-orders of magnitude.     

Capillary electrophoresis/electrochemical detection system with on-line deoxygenation

A capillary electrophoresis (CE)/electrochemical detection system with on-line deoxygenation was developed, consisting of a deoxygenation injector, a deoxygenation protector, and an electrochemical detection cell. When the system was utilized for 60 min, the steady-state current of oxygen detected could be dropped to 3% of the original value for the gold/mercury amalgam electrode and to 8% of the original value for the gold electrode, and the limit of detection could be decreased two orders of magnitude for the reducible analytes such as TI+ (from 3.1 x 10-5 mol/L to 8.0 x 10-7 mol/L) and metronidazole (from 3.8 x 10-5 mol/L to 4.0 x 10-7 mol/L).     

Capillary electrophoresis coupled with electrochemical detection using porous etched joint for determination of antioxidants

Capillary electrophoresis coupled with electrochemical detection (CE-EC) for determination of antioxidants, propyl gallate (PG) and tert-butylhydroquinone (TBHQ), in cosmetic samples was proposed in this work. A porous etched joint was used to isolate the electrochemical detection from the electrophoretic high voltage. Compared with the 25 microm i.d. capillary without a decoupler in a CE-EC system, a 75 microm i.d. capillary applied in the present system gave an improvement in both sample injection and sensitivity. Moreover, the carbon fiber working electrode could be directly in touch with the end of separation capillary due to the elimination of the effect of separation voltage on the EC detection, so the alignment of working electrode and capillary became easy and the dead volume was also decreased. Baseline separation of the two antioxidants was achieved by CE in a 50 cm long x 75 microm i.d. capillary at 20 kV using 5.0 mmol L(-1) phosphate buffer (pH 8.00). 0.7 V (versus Ag/AgCl) was applied to the carbon fiber electrode for electrochemical detection. Under the optimal condition, the precisions (RSD, n=4) of peak height and migration time of PG and TBHQ were 2.39-3.59% and 0.34-0.44%, respectively. The detection limits of PG and TBHQ were 2.51x10(-6) and 4.88 x 10(-6) mol L(-1) for standard solution and 0.0751 and 0.0328 mg g(-1) for the real cosmetic samples with consumption of 0.3g sample. Analysis of TBHQ and PG in cosmetics samples was also achieved with the present system and the spiked recoveries of two analytes in cosmetics samples were in the range of 93.6-98.8%.     

Separation and determination of the macrolide antibiotics (erythromycin, spiramycin and oleandomycin) by capillary electrophoresis coupled with fast reductive voltammetric detection

Separation and determination of erythromycin, spiramycin and oleandomycin by capillary zone electrophoresis coupled with fast reductive voltammetric detection using an Hg-film electrode was investigated in a simple aqueous phosphate buffer system. The influence of pH, concentration of phosphate, applied voltage, capillary length and dimension on the separation was examined and optimized. The entire separation of erythromycin, spiramycin, and oleandomycin was achieved in a 0.2 mol/L phosphate buffer system without organic modifiers. The electrochemical detection parameters, such as electrode material, applied waveform, scan rate, preconcentration potentials and preconcentration times, were investigated and discussed. This approach provides high separation efficiency and high sensitivity for all compounds, with detection limits (3 x peak-to-peak baseline noise) of 7.5 x 10(-8) mol/L for spiramycin, and 3 x 10(-7) mol/ L for erythromycin and oleandomycin. The calibration plot of peak areas for each separated peak vs. concentration of analyte was found to be linear over three orders of magnitude.     

L-苏氨酸分子印迹传感器的制备及应用

采用电化学方法制备了纳米银/聚槲皮素修饰充蜡石墨电极(Ag/Qu/WGE)。以L-苏氨酸(L-Thr)为模板分子,将一定量的壳聚糖,L-Thr和Nafion的混合液涂布在Ag/Qu/WGE上,采用恒电位法电化学清洗除去模板分子L-Thr,得到基于壳聚糖/纳米银/聚槲皮素的L-Thr分子印迹复合膜修饰电极(TMIP/WGE)。采用场发射扫描电镜、红外光谱分析、X射线光电子能谱和电化学技术表征了TMIP/WGE的形成。TMIP/WGE对L-Thr具有良好的电催化氧化作用,可用于L-Thr的快速、灵敏检测,L-Thr的氧化峰电流(1.45 V)和其浓度在0.1~1.0μmol/L范围内呈良好的线性关系,检出限(3σ)为0.01μmol/L。该电极已成功用于苏氨酸发酵液中L-Thr的检测。     

Electrocatalytic oxidation of dopamine at an ionic liquid modified carbon paste electrode and its analytical application

A room-temperature ionic liquid N-butylpyridinium hexafluorophosphate was used as a binder to construct an ionic liquid modified carbon paste electrode, which was characterized by scanning electron microscopy and electrochemical impedance spectroscopy. The ionic liquid carbon paste electrode (IL-CPE) showed enhanced electrochemical response and strong analytical activity towards the electrochemical oxidation of dopamine (DA). A pair of well-defined quasireversible redox peaks of DA appeared, with the redox peaks located at 215 mV (E _pa) and 151 mV (E _pc) (vs. the saturated calomel electrode, SCE) in pH 6.0 phosphate buffer solution. The formal potential (E ^0′) was calculated as 183 mV (vs. SCE) and the peak-to-peak separation as 64 mV. The electrochemical behavior of DA on the IL-CPE was carefully investigated. Under the optimal conditions, the anodic peak currents increased linearly with the concentration of DA in the range 1.0 × 10⁻⁶–8.0 × 10⁻⁴ mol/L and the detection limit was calculated as 7.0 × 10⁻⁷ mol/L (3σ). The interferences of foreign substances were investigated and the proposed method was successfully applied to the determination of DA injection samples. The IL-CPE fabricated was sensitive, selective and showed good ability to distinguish the coexisting ascorbic acid and uric acid.     

Determination of hesperidin and synephrine in Pericarpium Citri Reticulatae by capillary electrophoresis with electrochemical detection

A method based on capillary electrophoresis with electrochemical detection (CE-ED) has been developed for the determination of hesperidin (HP) and synephrine (SP) in the Chinese traditional herbal drug, Pericarpium Citri Reticulatae, the dried rind of the ripe fruits of Citrus reticulata Blanco (mandarin orange). The effects of some important factors such as the acidity and concentration of running buffer, separation voltage, and detection potential were investigated to determine the optimum conditions. The working electrode was a 300 microm diameter carbon disc electrode positioned opposite the outlet of the capillary. Both analytes could be well separated within 5 min in a 40 cm long capillary at a separation voltage of 12 kV in 50 mmol L(-1) borate buffer (pH 9.0). Excellent linearity was observed for the dependence of peak current on analyte concentration in the range from 2.5 x 10(-6) to 1.0 x 10(-3) mol L(-1) for SP and from 5.0 x 10(-6) to 1.0 x 10(-3) mol L(-1) for HP. The detection limits (S/N=3) for SP and HP were 4.96 x 10(-7) mol L(-1) and 6.54 x 10(-7) mol L(-1), respectively. This method has been successfully applied for the analysis of real samples, with satisfactory results.     

Evaluation of a sol-gel derived carbon composite electrode as an amperometric detector for capillary electrophoresis

In this paper, we report the construction and application of a sol-gel derived carbon composite electrode (CCE) as an amperometric detector for capillary electrophoresis. The electrochemical properties were characterized and compared with those of conventional carbon fiber and carbon paste electrode (CPE). Experimental results show that peak-to-peak noise of CCE was about 20% of CPE and electrode capacitance was comparatively low. When applied to the detection of dopamine and epinephrine, the optimal detection potential for CCE was 0.1 V lower than CPE under the same separation conditions; CCE with diameter of 75 and 100 microm could achieve a low detection limit of 3 x 10(-8) and 6 x 10(-8) M for the detection of epinephrine, which approaching that of the 33-microm diameter carbon fiber electrode. Also, the linearity for epinephrine at CCE was more than two orders of magnitude, which was slightly wider than that of carbon fiber electrode. Applications to real sample analysis were tested by the determination of betahistine dihydrochloride in tablets and human urine. Using CCE with diameter < or = 100 microm as an amperometric detector after capillary electrophoresis separation, a low detection limit and a wide linear range combined with excellent reproducibility were obtained. This CCE possesses of many advantages, namely, convenience, ease of fabrication, low cost and high stability.     

Determination of rate constants and activation energy of 3-chloro-1,2-propanediol hydrolysis by capillary electrophoresis with electrochemical detection

A method based on capillary electrophoresis with electrochemical detection (CE-ED) to calculate the rate constants and activation energy of 3-chloro-1,2-propanediol (3-MCPD) hydrolysis was described. Effects of several factors, such as the pH value and the concentration of the running buffer, separation voltage, injection time and the potential applied to the working electrode, were investigated to find the optimum conditions. With a 50 cm length of 25 microm diameter fused-silica capillary at a separation of 10 kV, well-defined separation of 3-chloro-1,2-propanediol from glycerol was achieved in 30 mmol/l borax (pH 9.24) within 13 min. Operated in a wall-jet configuration, a 328 microm copper-disk electrode used as the working electrode exhibits good response at 0.65 V (versus SCE) for 3-MCPD and glycerol. The rate constants of 3-MCPD hydrolysis at different temperatures were determined by monitoring the concentration changes of 3-MCPD. At 80, 85 and 90 degrees C, the measured rate constants of 3-MCPD hydrolysis were 3.8 x 10(-3) min(-1), 7.1 x 10(-3) min(-1) and 11.5 x 10(-3) min(-1), respectively. The activation energy for 3-MCPD hydrolysis was calculated to be 118.1 kJ/mol, which is in good agreement with the value in the literature.     

Determination of amino acids in tobacco samples by capillary electrophoresis/indirect absorbance detection with isolation of the electrolysis compartment and p-Aminobenzoic acid as a background electrolyte.

A fast, convenient and sensitive method of capillary zone electrophoresis (CZE) and indirect UV detection was proposed for the determination of 16 amino acids. p-Aminobenzoic acid (PAB) was selected as a background electrolyte (BGE). An isolated cell included a BGE buffer part and an electrode buffer one, which were jointed with a glass frit. The isolated cell can prevent PAB from the electrode reaction and improve the stability of the detection baseline. The separation conditions of amino acids were investigated, such as different BGEs, BGE concentration, buffer pH and electroosmotic flow (EOF) modifiers. Under the selected separation conditions, 14 amino acid peaks could be separated in 12 min. The detection limits of the amino acids were in the range of 1.7 - 4.5 micromol/L. The isolated cell is suitable for reagents reacting on the electrodes in capillary electrophoresis. The proposed method has been successfully applied to the determination of the amino acids in tobacco samples.     

Determination of idarubicin in human urine by capillary zone electrophoresis with amperometric detection

A simple, reliable and reproducible method, based on capillary zone electrophoresis with amperometric detection, has been developed for the determination of idarubicin in human urine. A carbon disk electrode was used as working electrode. The optimal conditions of separation and detection were pH 5.6 phosphate buffer (0.20 mol/L), 22 kV for the separation voltage and 1.00 V (vs. Ag/AgCl, 3 mol/L KCl) for the detection potential. The linear range was from 4.0 x 10(-7) to 2.0 x 10(-5) mol/L with a regression coefficient of 0.9986, and the detection limit was 8.0 x 10(-8) mol/L. The method was directly applied to the determination of idarubicin in spiked human urine without any other sample pretreatment except filtration, and the assay results were satisfactory.