P改性对Mo-Ni/Al2O3煤焦油加氢脱氮性能的影响

在磷含量1.34%下,采用分步浸渍法按磷添加顺序不同制备了3种改性催化剂:MoP-Ni/Al₂O₃、Mo-NiP/Al₂O₃、Mo-Ni/PAl₂O₃.通过X射线衍射(XRD)、程序升温脱附(NH₃-TPD)、程序升温还原(H₂-TPR)、氮气吸附等技术对催化剂进行了表征.以新疆中低温煤焦油为原料,考察了不同磷改性方式对催化剂加氢脱氮(HDN)性能的影响.结果表明,适宜的磷添加方式能够改变催化剂的酸性分布,提高10~13 nm加氢脱氮有效孔的比例,并且减弱活性组分与载体的相互作用,同时使得活性组分更易被还原,进而提高催化剂加氢脱氮性能.加氢脱氮活性顺序为Mo-Ni/PAl₂O₃(74.36%)>Mo-NiP/Al₂O₃(72.74%)>Mo-Ni/Al₂O₃(71.72%)>MoP-Ni/Al₂O₃(56.13%).     

磷含量对NiMo/γ-Al2O3催化剂活性相结构的影响

采用程序升温还原（TPR）、高分辨透射电镜（HRTEM）和X射线光电子能谱（XPS）表征手段对共浸渍法制备的不同磷含量NiMo/γ-Al₂O₃催化剂进行了表征,研究了磷含量对NiMo/γ-Al₂O₃催化剂活性相结构的影响。TPR研究表明,磷能够减少四面体配位Mo物种的数量,增加八面体配位Mo物种的数量,促进高活性Ⅱ型"Ni-Mo-S"活性相的形成。HRTEM研究表明,随磷含量的增加,MoS₂颗粒堆积层数增加,催化剂的加氢选择性提高;适量磷能够增加边角位有效Mo原子的分散度(fMo),增加催化剂表面加氢脱硫（HDS）和加氢脱氮（HDN）活性位的数量。上述结论得到了XPS表征的证实：适量磷增加了催化剂表面Mo原子浓度、提高有效助剂比率（PR）和提升比率（Ni/Mo）,相应催化剂表现出最高的HDS和HDN活性;但过高磷含量能够引起MoS₂颗粒过度堆积,片层长度过长,导致活性位数量减少,催化活性降低。     

乙二醇对磷掺杂NiMo/Al_2O_3加氢催化剂性能的影响

采用NiMoP浸渍液中添加乙二醇(EG)的方式制备了不同EG含量的NiMoP(x)/Al_2O_3催化剂,为研究EG及其含量对该系列催化剂催化性能和活性相结构的影响,用二苯并噻吩(DBT)和喹啉(Q)为模型化合物,考察了催化剂的加氢脱硫(HDS)和加氢脱氮(HDN)性能。结果表明,在EG添加量较低的情况下(EG/Ni物质的量比分别为0、0.5、1、2、3),EG能够明显提高催化剂对DBT和Q的HDS和HDN活性,其中,HDN活性提高幅度大于HDS,且随着EG含量提高,催化剂的HDS和HDN活性进一步提高。通过TEM分析和XPS分析可知,EG有助于增加催化剂中MoS_2颗粒的堆积层数和片层长度,且随着EG含量增加,堆积层数和片层长度都有所增加;EG有助于提高Mo表面原子浓度,对Ni表面原子浓度影响较小,但明显提高了Mo和Ni硫化程度。TG表征说明,EG在氧化铝和催化剂表面存在多种相互作用方式,并且存在与活性组分相互作用的耐高温有机物种。     

Temperature-activated hydrogen adsorption on Ir/Al2O3

A strongly temperature-activated character of hydrogen sorption on supported iridium has been observed. Activated hydrogen sorption as a function of temperature grows, at first, rapidly and its further, relatively gentle increase is probably due to a spillover effect.

---

. , , , , .

     

Sulfurization of Pt/Al2O3?Cl catalysts. IV. Adsorption sites of H2S on Al2O3, Al2O3?Cl and Pt/Al2O3?Cl

Chemisorption of H₂S on Al₂O₃, Al₂O₃–Cl and Pt/Al₂O₃–Cl has been studied by gravimetry and IR spectroscopy. The influence of the amount of Cl on the H₂S adsorption equilibrium value and the nature of the adsorption sites at low and high coverages are discussed.

---

H₂S Al₂O₃, Al₂O₃–Cl Pt/Al₂O₃–Cl . Cl H₂S, .

     

Preparation of fibrous CoMo/Al2O3 hydrotreating catalysts by the sol-gel method

Fibrous CoMo–Al oxide hydrotreating catalysts have been prepared by the sol-gel method. It is shown that their catalytic properties are similar to the properties of commercial catalysts prepared by traditional methods.     

助剂SiO_2对CoMo/Al2O3-SiO_2催化剂结构的影响研究

采用原位红外光谱、拉曼光谱、紫外光谱和H2-TPR表征技术对CoMo/Al_2O_3-SiO_2催化剂进行了表征。结果表明,增加CoMo/Al_2O_3-SiO_2催化剂中的SiO_2含量会促进八面体配位钼物种向四面体配位钼物种转变,SiO_2含量越高这种结构转变趋势越显著。在CoMo/Al_2O_3催化剂载体中加入适量的SiO_2能够改变载体与活性金属的相互作用,提高了催化剂加氢脱硫活性。     

TPR studies on steam reforming of 2-propanol on Rh/Al2O3, Ru/Al2O3 and Pd/Al2O3

Reaction pathways for steam reforming of 2-propanol (isopropyl alcohol, IPA) on Rh/Al₂O₃, Ru/Al₂O₃ and Pd/Al₂O₃ have been studied by temperature-programmed reactions (TPRs) of IPA and acetone in the presence of steam. The results of TPRs suggest that that of IPA on Rh/Al₂O₃ and Ru/Al₂O₃ proceeds via acetone, while the steam reforming of IPA on Pd/Al₂O₃ takes place via propene from acetone. This revised version was published online in August 2006 with corrections to the Cover Date.     

制备方法对Fe2O3/Al2O3-ZrO2在乙苯脱氢反应中催化性能的影响

为提高含铁催化剂的脱氢活性,采用浸渍法和一步沉淀法制备了Fe、Al和Zr含量相同的F4AZ10-imp和F4AZ10-pre催化剂,在550 ℃考察了其在乙苯CO₂氧化脱氢制苯乙烯反应过程中的催化性能,并结合XRD、N₂-吸附、NH₃-TPD、CO₂-TPD和H₂-TPR等表征手段对催化剂进行了分析。结果表明,与浸渍法相比,一步沉淀法制备的催化剂更有利于活性组分Fe₂O₃在催化剂表面的分散及反应物CO₂的转化。     

Catalytic activity of NiMo/TiO2?Al2O3 systems in thiophene hydrodesulfurization

A correlation exists between the number of surface acid sites and the catalytic activity of NiMo/TiO₂–Al₂O₃ systems in thiophene hydrodesulfurization. The catalytic activity for thiophene hydrodesulfurization and surface concentration of Brönsted acid sites increase with the titania content in the TiO₂–Al₂O₃ support.     

Interaction of methanol with hydrogen sulfide in the presence of K2WO4/Al2O3

Kinetic data show that in the presence of K₂WO₄/Al₂O₃, methanethiol is largely produced by the reaction of H₂S with metanol and partly with dimethyl ether. Dimethyl sulfide is formed during the interaction of methanethiol with methanol, of H₂S with dimethyl ether and as a result of methanethiol disproportionation. Methane and carbon oxides are the decomposition products of methanethiol and dimethyl sulfide and of methanol and dimethyl ether, respectively.

---

, K₂WO₄/Al₂O₃ H₂S — . , H₂S . , — .

     

Sulfuration of Pt/Al2O3, Pt?Re/Al2O3 and Pt?Ir/Al2O3 catalysts

Three reforming catalysts Pt/Al₂O₃, Pt–Ir/Al₂O₃ and Pt–Re/Al₂O₃ have been sulfurated by H₂S and tested by their activities in benzene hydrogenation. By treatment at 500°C under hydrogen flow only a part of the initial activity of the non-sulfurated catalyst is retained. So only a part of the adsorbed sulfur is easily removed in these conditions. The remaining sulfur for each of the catalysts (Pt/Al₂O₃, Pt–Ir/Al₂O₃ and Pt–Re/Al₂O₃) gives the same atomic ratio of 0.5 sulfur atom per accessible metallic atom.

---

Pt/Al₂O₃, Pt–Ir/Al₂O₃ Pt–Pe/Al₂O₃ . 500°C H₂ . . ., . (Pt/Al₂O₃, Pt–Ir/Al₂O₃ Pt–Pe/Al₂O₃) 0,5.

     

Effect of the activation conditions on the catalytic properties of Pt/Al2O3 catalysts

The effect of the activation conditions of Pt/Al₂O₃ catalysts has been investigated in the hydrogenation of benzene and in the hydrogenolysis of ethane. Whatever the conditions of calcination or reduction, specific activities of all catalysts for benzene hydrogenation remain constant. On the other hand, for identical dispersities, the cacination in a wet argon flow increases the specific activity of platinum for hydrogenolysis of ethane, pointing out the role of wet pretreatment on defect building or on the faceting of supported metallic catalysts.

---

Pt/Al₂O₃ . , . , , . .

     

TiO_2掺杂CuMnCe/Al_2O_3催化剂对甲烷催化燃烧脱氧反应的影响

以掺杂了不同TiO_2含量的Al_2O_3作为载体,通过等体积浸渍法制备了一系列不同TiO_2含量的CuMnCe/TiO_2-Al_2O_3催化剂,用BET、H_2-TPR、XRD和XPS表征技术对催化剂物理化学性质进行表征,并考察了催化剂在含甲烷气脱氧反应中的催化性能。结果表明,在载体中添加TiO_2对催化剂活性组分的晶相结构和分散度没有明显影响;但有效改善了Al_2O_3载体抗烧结能力;增加了CuMnCe/Al_2O_3催化剂表面Ce~(3+)/(Ce~(3+)+Ce~(4+))的相对含量,从而提高了活性氧的移动性,且使催化剂表面可氧化还原物种含量和表面吸附氧Osur/(Osur+Olatt)的含量增多。有效改善了催化剂在含甲烷气催化燃烧脱氧上的催化活性。其中,CuMnCe/4%TiO_2-Al_2O_3表现出最优的催化活性,在387℃时可使含甲烷气中氧气的转化率达到100%。     

氧化铝载体硫酸化对锰铈催化剂SCR脱硝性能的影响

分别以硫酸改性前后的氧化铝为载体,采用浸渍法制备了锰铈催化剂,对其NH_3-SCR脱硝性能进行评价,并采用XRD、BET、NH_3-TPD、H_2-TPR以及FT-IR对催化剂进行了表征。结果表明,改性降低了金属的分散性和氧化性,增加了酸量,特别是B酸量;催化剂的最佳脱硝温度窗口向高温扩展,活性温度窗口范围变宽,并且,改性液浓度越大变化幅度越大。当反应温度在200-250℃时,未改性催化剂与采用0.2 mol/L硫酸改性的催化剂具有接近的催化活性,但改性后的催化剂具有更高的抗水抗硫活性,250℃时脱硝率可达70%。     

Pyrolytic and catalytic conversion of rape oil into aromatic and aliphatic fractions in a fixed bed reactor on Al2O3 and Al2O3/B2O3 catalysts

In the, at present, unstable fuel market, much attention is devoted to alternative technologies for fuel production and development of alternative products of the petrochemical industry. One of the prospective sources of fuel and alternative petrochemical products is biomass, and the use of oil plants is one of the possibilities. This paper reports on a possible conversion of rapeseed oil produced in Poland into intermediate hydrocarbon fractions by pyrolysis combined with parallel catalytic conversion. The products were analysed by gas chromatography coupled with a mass detector. The process was performed in a fixed-bed reactor and was monitored by FTIR and ¹H NMR. Depending on the catalysts applied, the products contained: water, carbon oxides, hydrogen, aliphatic or aromatic hydrocarbons accompanied by some amount of C2-C5 hydrocarbons formed during the cracking process. Presented at the 35th International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 26–30 May 2008.     

Influence of the activation temperature on structural and textural properties of NiMo/Al2O3 hydrodesulfurization catalysts

Investigations of a commercial NiMo/Al₂O₃ hydrodesulfurization (HDS) catalyst are directed towards optimization of the activation procedure of HDS catalyst concerning active phase formation and thermal stability. Structural and textural data obtained with XRD, IR-FTIR, XPS and LTNA reveal that the optimal temperature for the formation of active species on the catalyst surface and an appropriate pore structure is 300°C.     

Kinetic studies of hydrogen and carbon monoxide adsorption on Re2O7/Al2O3 catalysts

Kinetic studies of hydrogen and carbon monoxide adsorption on reduced Re₂O₇/Al₂O₃ catalysts have revealed that its activation energy decreases with increasing reduction degree of rhenium oxide. Adsorption of gases is suggested to take place on metallic rhenium atoms.

---

- . , . , .

     

Partial oxidation of methane on Cr2O3/Al2O3

The oxidation of methane on supported chromia was studied at temperatures varying between 423 and 743 K and CH₄/O₂ ratios between 1 and 9 in a differential reactor. The main reaction products observed were carbon monoxide and formaldehyde. The rates of reaction obey a power law expression.

---

, 423 743 CH₄/O₂ 1 9, . . .

     

Investigation of the acidity of Ni/Al2O3 and Ni/SiO2?Al2O3 catalysts

Acidity of Ni-modified alumina and silica-alumina catalysts was determined using n-butylamine titration and pyridine adsorption methods. Strong influence of Ni²⁺ ions on the Brönsted acidity of silicaalumina was observed. Improved Brönsted acidity of such system was confirmed by the results of the test reaction.