Enhanced and selective adsorption of mercury ions on chitosan beads grafted with polyacrylamide via surface-initiated atom transfer radical polymerization

Enhanced and selective removal of mercury ions was achieved with chitosan beads grafted with polyacrylamide (chitosan-g-polyacrylamide) via surface-initiated atom transfer radical polymerization (ATRP). The chitosan-g-polyacrylamide beads were found to have significantly greater adsorption capacities and faster adsorption kinetics for mercury ions than the chitosan beads. At pH 4 and with initial mercury concentrations of 10-200 mg/L, the chitosan-g-polyacrylamide beads can achieve a maximum adsorption capacity of up to 322.6 mg/g (in comparison with 181.8 mg/g for the chitosan beads) and displayed a short adsorption equilibrium time of less than 60 min (compared to more than 15 h for the chitosan beads). Coadsorption experiments with both mercury and lead ions showed that the chitosan-g-polyacrylamide beads had excellent selectivity in the adsorption of mercury ions over lead ions at pH < 6, in contrast to the chitosan beads, which did not show clear selectivity for either of the two metal species. Mechanism study suggested that the enhanced mercury adsorption was due to the many amide groups grafted onto the surfaces of the beads, and the selectivity in mercury adsorption can be attributed to the ability of mercury ions to form covalent bonds with the amide. It was found that adsorbed mercury ions on the chitosan-g-polyacrylamide beads can be effectively desorbed in a perchloric acid solution, and the regenerated beads can be reused almost without any loss of adsorption capacity.     

Using NaCl particles as porogen to prepare a highly adsorbent chitosan membranes

Macroporous chitosan membranes were prepared by using NaCl particles porogen and genipin as cross-linking agent. For characterization and sorption behavior comparison, other genipin cross-linked chitosan membranes were prepared by either freeze drying or by using silica particles as porogen. The mean pore diameter, the porosity, the crystallinity index (CrI) as well as the effect of the drying procedures of these chitosan membranes were examined. NaCl reduced the CrI of the chitosan membrane. The oven drying (OD) procedure decreased the mean pore diameter, the porosity, and increased the CrI of the chitosan membranes when compared with the vacuum drying (VD) procedure. The heat treatment of chitosan membrane in aqueous NaOH to attract silica porogen increased the CrI of the membrane. Under the same conditions, the membranes prepared with NaCl had better sorption performance on RR 189 and Cu²⁺ than other membranes. The maximum sorption capacity (q_e) reached 1836.17 mg RR 189/g chitosan and 151.98 mg Cu²⁺/g chitosan. The pore diameter (d_pore) of the membranes was much larger than the diameter of the adsorbate molecules (d_adsorbate), such that the ratio of d_pore/d_adsorbate had little influence on q_e. The porosity and the amorphous extent of the membranes were almost the same on q_e. When using tyrosinase catalyzing, the hydrocaffeic acid (HCA) grafted on the NaCl treated chitosan membrane was almost 10 times more than on chitosan beads. The chitosan membrane prepared with NaCl can be used as a good adsorbent with high loading capacity for implanting molecules (such as ligands, enzymes, etc.) on.     

Dye-labeled silver nanoshell-bright particle

Silica beads with average diameters of 40-600 nm were prepared, and Ru(bpy)3(2+) complexes were incorporated into the beads. These beads were coated by silver layer by layer to generate porous but continuous metal nanoshells. The thicknesses of these metal shells were 5-50 nm. The emission band from the dyes in the silica cores was more narrow and the intensity was enhanced with growth of silver shell thickness due to coupling of the emission light from Ru(bpy)3(2+) in the cores with the metal plasmon from the silver shells. The enhancement of emission intensity was also dependent on the size of the silica core, showing that the enhancement efficiency decreased with an increase in the size of the silica beads. Lifetime measurements support the coupling mechanism between the dye and metal shell. This study can be used to develop novel dye-labeled metal particles with bright and narrow emission bands.     

Immobilization of cellulose extracted from Robinia Pseudoacacia seed fibers onto chitosan: Chemical characterization and study of methylene blue removal

The design of economical adsorbents to remove pollutants from contaminated water is attracting more attention. In this study, cellulose was successfully extracted from Robinia Pseudoacacia seed fibers and immobilized onto chitosan beads. The prepared spherical beads were then used for the biosorption of methylene blue dye from aqueous media. Samples were investigated using several analytical methods, namely FT-IR, XRD, EDX, SEM, and TGA analyses. The adsorption experiments showed that combining cellulose with chitosan improved the removal of methylene blue. The maximum uptake amount of methylene blue using cellulose–chitosan composite beads was 55 mg/g. However, it was about 35 mg/g at 20 °C for chitosan beads. The kinetic data complied strongly with the pseudo-second order equation, suggesting that the biosorption phenomenon has predominantly a chemical nature. Overall, the current study has shown a promising technique to design new adsorbents from abundant natural polymers for eliminating cationic dyes from water.     

A novel support for antibody purification: Fatty acid attached chitosan beads

Linoleic acid attached chitosan beads [poly(LA-Ch)] (1.25 μm in diameter) are obtained by the formation of amide linkages between linoleic acid and chitosan. Poly(LA-Ch) beads are characterized by FTIR, TEM, and swelling studies. Poly(LA-Ch) beads are used for the purification of immunoglobulin-G (IgG) from human plasma in a batch system. The maximum IgG adsorption is observed at pH 7.0 for HEPES buffer. IgG adsorption onto the plain chitosan beads is found to be negligible. Adsorption values up to 136.7 mg/g from aqueous solutions are obtained by poly(LA-Ch) beads. IgG adsorption saw an increase as a result of increasing temperature. Higher amounts of IgG are adsorbed from human plasma (up to 390 mg/g) with a purity of 92%. The adsorption phenomena appeared to follow a typical Langmuir isotherm. It is observed that IgG could be repeatedly adsorbed and desorbed without significant loss when we take into account the adsorption amount. It is concluded that the poly(LA-Ch) beads allowed one-step purification of IgG from human plasma.     

Highly Porous Hydroxyapatite/Graphene Oxide/Chitosan Beads as an Efficient Adsorbent for Dyes and Heavy Metal Ions Removal

Dye and heavy metal contaminants are mainly aquatic pollutants. Although many materials and methods have been developed to remove these pollutants from water, effective and cheap materials and methods are still challenging. In this study, highly porous hydroxyapatite/graphene oxide/chitosan beads (HGC) were prepared by a facile one-step method and investigated as efficient adsorbents. The prepared beads showed a high porosity and low bulk density. SEM images indicated that the hydroxyapatite (HA) nanoparticles and graphene oxide (GO) nanosheets were well dispersed on the CTS matrix. FT-IR spectra confirmed good incorporation of the three components. The adsorption behavior of the obtained beads to methylene blue (MB) and copper ions was investigated, including the effect of the contact time, pH medium, dye/metal ion initial concentration, and recycle ability. The HGC beads showed rapid adsorption, high capacity, and easy separation and reused due to the porous characteristics of GO sheets and HA nanoparticles as well as the rich negative charges of the chitosan (CTS) matrix. The maximum sorption capacities of the HGC beads were 99.00 and 256.41 mg g⁻¹ for MB and copper ions removal, respectively.     

Effect of MWCNTs Doping on the Morphology,Structure and Properties of Chitosan Beads

A series of chitosan (CS)/multi-walled carbon nanotubes (MWCNTs) composite hydrogel beads with different MWCNTs contents are prepared via a solution blending method. The effects of MWCNTs on the morphology, structure and properties of chitosan beads have been investigated. Digital pictures show that the composite beads obtained are of good morphological characteristics, and the SEM micrographs indicate that the addition of MWCNTs into CS beads made the surface of the CS/MWCNTs hydrogel beads contain much larger wrinkles. Fourier transform infrared spectra (FTIR) show that the main chain of CS bead is not changed, but there are some electrostatic interactions between CS and MWCNTs, which lead to very significant changes in the crystallization behavior of CS and MWCNTs. The thermal stability of CS/MWCNTs composites at high temperatures is increased with the existence of MWCNTs, indicating a possible electrostatic interaction between MWCNTs and CS lattices to limit the motivation of CS. The adsorption capacity of CS beads doped with a lower percentage of MWCNTs (0.02 wt%) for acid fuchsin is 112.76 mg/g, higher than that of pure CS beads (35.62 mg/g).     

A NOVEL APPROACH TO SYNTHESIZE CHITOSAN BEADS CROSSLINKED BY EPICHLOROHYDRIN

1. INTRODUCTION Chitosan is the deacetylated chitin which is one of the most abundant natural polymers produced from crab, lobster and shrimp shells or fungal fermentation processes [1]. It is a family of deacetylated β1→4 D-glucosamine polymers. Chitosan has properties including bioactivity, biocompatibility and biodegradability, so it is potentially more useful than cellulose for developing advanced of attention not only as an unutilized biomass resource but also as a novel type of sp…     

A NOVEL APPROACH TO SYNTHESIZE CHITOSAN BEADS CROSSLINKED BY EPICHLOROHYDRIN

The present investigation describes a novel method for preparing spherical chitosan particles based on crosslinking with epichlorohydrin.Certain amount of pre-crosslinking agent was added to form chitosan gels by traditional inverse phase suspension polymerization.Then the gels were crosslinked by epichlorohydrin at basic condition to obtain chitosan beads.The effects of reaction conditions,such as crosslinking time,the amount of crosslinking agent and the NaOH concentration,on the physical properties of the chitosan beads were investigated.The beads were found to have more amino groups in the polymer chains than the beads crosslinked by glutaraldehyde.The capacity for copper ions in as high as 40mg/g,The beads have good mechanical strength and can be reused.     

氨基酸修饰壳聚糖对胆固醇的吸附作用

通过将不同脱乙酰度的壳聚糖粉末与戊二醛交联,再经苯丙氨酸和色氨酸修饰,得到了两种珠状壳聚糖吸附剂,并进而研究了有关吸附剂对胆因醇的吸附性能。实验表明,交联壳聚糖珠对ＣＨＯ的吸附能力比壳聚糖粉末降低,而经不同氨基酸修饰后的壳聚糖珠对ＣＨＯ吸附能力提高,用Ｐｈｅ修饰比用Ｔｒｙ修饰的珠吸附性能更好些。     

Macroporous chitosan layer coated on non-porous silica gel as a support for metal chelate affinity chromatographic adsorbent

A new immobilized metal affinity chromatography (IMAC) matrix was prepared by coordinating Cu2+ with cross-linked chitosan coated on non-porous silica gel (Cu-CTS-SiO2). Macroporous structure could be formed on the coated layer by imprinting polyethylene glycol (PEG) in chitosan film. The surface morphology changes on Cu-CTS-SiO2 bead prepared in different condition were confirmed by scanning electron microscopy (SEM). Effects of chitosan and PEG content in coating solution, the molecular mass of PEG on the surface macropore formation and adsorption capacity of bovine serum albumin (BSA) were investigated. Results indicated that coating solution with 2% chitosan and 10% PEG 20000 was optimal. Batch experiments were also conducted for elucidating the optimal pH, the adsorption isotherm and adsorption kinetics of BSA. Adsorption isotherm of trypsin on the same adsorbent was also performed. Results showed that the support itself had low non-specific interaction with both BSA and trypsin. The maximum adsorption capacity for BSA and trypsin on the prepared IMAC adsorbent could reach 192 mg and 5000 IU, respectively calculated by every gram of chitosan. The binding and eluting condition for BSA were tested on column filled with the adsorbent. Crude BSA sample could be purified on the IMAC column.     

Electrophoretic extraction and analysis of DNA from chitosan or poly-l-lysine-coated alginate beads

Alginate beads containing entrapped DNA were produced using both external and internal calcium sources, and coated with chitosan or poly-l-lysine membranes. The beads were assayed with DNase nuclease to determine formulation conditions offering the highest level of DNA protection fromnucleic acid hydrolysis, simulating gastrointestinal exposure. A method was developed to extract and assay intracapsular DNA through a modified agarose electrophoresis system. Both external and internally gelled beads were permeable to DNase (M_w=31 kDa), indicated by the absence of DNA after nuclease exposure. At low levels of DNase exposure, coated high guluronic content alginate beads offered a higher level of DNA protection compared with coated beads with low guluronic alginate. No apparent correlation was found with chitosan membrane molecular weight and degree of deacetylation; however, increasing poly-l-lysine molecular weight appeared to increase DNase exclusion from beads. At elevated levels of DNase exposure, DNA hydrolysis was evident within all coated beads with the exception of those coated with the highest molecular weight poly-l-lysine (M_w=197.1 kDa), which provided almost total nuclease protection. Optimal combination then for DNA protection from nucleases is a high guluronic alginate core, coated with high molecular weight poly-l-lysine.     

Heavy Metal Removal from Synthetic Solutions with Magnetic Beads Under Magnetic Field

The aim of this study is to prepare magnetic beads which can be used for the removal of heavy metal ions from synthetic solutions. Magnetic poly(ethylene glycol dimethacrylate‐vinyl imidazole) [m‐poly(EGDMA‐VIM)] beads were produced by suspension polymerization in the presence of magnetite Fe₃O₄ nano‐powder. The specific surface area of the m‐poly(EGDMA‐VIM) beads was found to be 63.1 m²/g with a size range of 150–200 µm in diameter and the swelling ratio was 85%. The average Fe₃O₄ content of the resulting m‐poly(EGDMA‐VIM) beads was 12.4%. The maximum binding capacities of the m‐poly(EGDMA‐VIM) beads were 32.4 mg/g for Cu²⁺, 45.8 mg/g for Zn²⁺, 84.2 mg/g for Cd²⁺and 134.5 mg/g for Pb²⁺. The affinity order on mass basis is Pb²⁺>Cd²⁺>Zn²⁺>Cu²⁺. Equilibrium data agreed well with the Langmuir model. pH significantly affected the binding capacity of the magnetic beads. Binding of heavy metal ions from synthetic wastewater was also studied. The binding capacities were 26.2 mg/g for Cu²⁺, 33.7 mg/g for Zn²⁺, 54.7 mg/g for Cd²⁺ and 108.4 mg/g for Pb²⁺. The magnetic beads could be regenerated up to about 97% by treating with 0.1 M HNO₃. These features make m‐poly(EGDMA‐VIM) beads a potential candidate for support of heavy metal removal under magnetic field.     

Preparation of ion-exchange beads based on poly(methacrylic acid) brush grafted chitosan beads: Isolation of lysozyme from egg white in batch system

Poly(methacrylic acid) brush grafted crosslinked-chitosan (chitosan-g-poly(MAA)) beads were prepared in two sequential steps: in the first step, chitosan beads were prepared by phase-inversion technique and then were crosslinked with epichlorohydrin under alkaline condition; in the second step, the graft copolymerization of methacrylic acid onto the chitosan beads was initiated by ammonium persulfate (APS) under nitrogen atmosphere. The chitosan-g-poly(MAA) beads were first used as an ion exchange support for adsorption of lysozyme (LYZ) from aqueous solution. The influence of pH, equilibrium time, ionic strength and initial LYZ concentration on the adsorption capacity of the chitosan-g-poly(MAA) ion-exchange beads has been investigated in a batch system. Maximum LYZ adsorption onto chitosan-g-poly(MAA) beads was found to be 65.7 mg/g at pH 6.0. The experimental equilibrium data obtained LYZ adsorption onto chitosan-g-poly(MAA) ion-exchange beads fitted well to the Langmuir isotherm model. Kinetics parameters of this adsorption system were also analyzed by using the equilibrium experimental data. The result of kinetic analyzed for LYZ adsorption onto ion-exchange beads showed that the second order rate equation was favourable. Finally, the chitosan-g-poly(MAA) ion-exchange beads were used for the purification of LYZ from egg white in batch system and the purity of the eluted LYZ from ion-exchange chitosan-g-poly(MAA) beads was determined as 94% by HPLC from single step purification.     

染料壳聚糖微球的制备及其对牛血清白蛋白(BSA)吸附性能的研究

采用反相悬浮交联法制备壳聚糖微球,对微球进行羟丙基氯化及氨基化,并偶联色素配体Cibacron Blue F3GA,得到一种新型染料亲和吸附剂.以牛血清白蛋白(BSA)为目标蛋白,考察了该染料亲和吸附剂的吸附性能,发现其对BSA有较高的吸附量(95.2mg/g),吸附行为满足Langmuir吸附等温式.负载牛血清白蛋白的微球容易洗脱,洗脱率高达99％.     

染料壳聚糖微球的制备及其对人血清白蛋白吸附性能研究

人血清白蛋白(Human Serum Albumin,HSA)是血浆中含量最丰富的蛋白质,约占血浆总蛋白的60%.在人体内,HSA有许多重要的生理功能[1],临床上广泛应用于手术输血和危重病人补液,治疗创伤休克、烧伤、水肿和低白蛋白血症等,而且能增强人体抵抗能力,是迄今为止产量最大、临床用量最大     

固定化木瓜蛋白酶的制备和性质研究

多孔硅球固定化木瓜蛋白酶具有热增活性 .本文在前文研究的基础上 ,用载体交联法制备了甲壳胺固定化木瓜蛋白酶和纤维素固定化木瓜蛋白酶 .考察了固定化pH值、戊二醛浓度和给酶量对固定化木瓜蛋白酶活力的影响 .研究了固定化木瓜蛋白酶的性质 ,特别是热稳定性和耐热性 ,并与溶液酶和多孔硅球固定化木瓜蛋白酶进行了比较 .所制得的甲壳胺固定化木瓜蛋白酶和纤维素固定化木瓜蛋白酶的最适反应温度均达到了 80℃ ;90℃温育 1h后固定化酶的活力保持在 95 %以上 ;70℃温育处理 5h和 6h后固定化酶的活力也仍能保持在 90 %以上 .固定化木瓜蛋白酶的热稳定性和耐热性得到了显著提高     

Radiation synthesis of chitosan beads grafted with acrylic acid for metal ions sorption

Radiation-induced grafting of acrylic acid onto chitosan beads was performed in solution at a dose rate of 20.6 Gy/min of cobalt-60 gamma rays. The effect of absorbed dose on grafting yield was investigated. The characterization of the grafted material was performed by FTIR spectroscopy and the swelling measurements at different pHs. The grafting yield increased with the increase in dose, it reached 80% at 40 kGy irradiation dose.The removal of Pb and Cd ions from aqueous solutions was investigated with both ungrafted and grafted chitosan beads. The sorption behavior of the sorbents was examined through pH, kinetics and equilibrium measurements. Grafted chitosan beads presented higher sorption capacity for both metal ions than unmodified chitosan beads.     

Adsorption of chromium from aqueous solution using chitosan beads

A basic investigation on the removal of Cr(III) and Cr(VI) ions from aqueous solution by chitosan beads was conducted in a batch adsorption system. The chitosan beads were prepared by casting an acidic chitosan solution into an alkaline solution. The influence of different experimental parameters; pH, agitation period and different concentration of Cr(III) and Cr(VI) ions was evaluated. A pH 5.0 was found to be an optimum pH for Cr(III) adsorption, and meanwhile pH 3.0 was the optimum pH for the adsorption of Cr(VI) onto chitosan beads. The Langmuir and Freundlich adsorption isotherm models were applied to describe the isotherms and isotherm constants for the adsorption of Cr(III) and Cr(VI) onto chitosan beads. Results indicated that Cr(III) and Cr(VI) uptake could be described by the Langmuir adsorption model. The maximum adsorption capacities of Cr(III) and Cr(VI) ions onto chitosan beads were 30.03 and 76.92 mg g⁻¹, respectively. Results showed that chitosan beads are favourable adsorbents. The Cr(III) and Cr(VI) ions can be removed from the chitosan beads by treatment with an aqueous EDTA solution.     

壳聚糖包裹硅胶载体印迹牛血红蛋白的研究

用壳聚糖包裹的硅胶为载体, 利用壳聚糖表面的氨基与戊二醛结合, 在硅胶表面引入醛基, 固定模板蛋白(牛血红蛋白). 用溶胶-凝胶过程再次包裹固定蛋白质的载体, 洗去模板蛋白后, 得到具有选择性识别的牛血红蛋白分子印迹聚合物. 用红外光谱(IR)、扫描电子显微镜(SEM)和元素分析对聚合物进行了表征, 结果表明, 载体表面成功地接枝了分子印迹聚合物. 选择性吸附实验结果表明, 分子印迹聚合物具有良好的识别性能, 能实现水溶液中牛血红蛋白的富集.