Determination of Trace Amounts of Copper by Adsorptive Stripping Voltammetry

ABSTRACT

A technique is presented for the determination of trace amounts of copper(II) by adsorptive cathodic stripping voltammetry. The procedure is based on adsorptive accumulation of copper(II)-Alizarin Red S (ARS) complex on a hanging mercury drop electrode, followed by a stripping voltammetric measurement of the reduction current of the adsorbed complex at -0.16 V (vs. Ag/AgCl). The height of the copper -ARS reduction peak is linearly dependent upon the copper(II) concentration between 0.2-15 and 15-500 ng.ml^?1. The detection limit of the technique is 0.05 ng.ml^?1 copper(II) for a collection time of 1 minute. The method is free from most interferences. The procedure has been successfully applied to the determination of trace amounts of copper(II) in some analytical grade salts.     

Selective determination of trace arsenic and antimony species in natural waters by gas chromatography with a photoionization detector

Traces amounts of arsenic and antimony in water samples were determined by gas chromatography with a photoionization detector after liquidnitrogen cold trapping of their hydrides. The sample solution was treated with sodium hydroborate (NaBH₄) under weak-acid conditions for arsenic(III) and antimony(III) determination, and under strong-acid conditions for arsenic(III+V) and antimony(III+V) determination. Large amounts of carbon dioxide (CO₂) and water vapor obscured determination of arsine and stibine. Better separation from interference could be achieved by removing CO₂ and water vapor in two tubes containing sodium hydroxide pellets and calcium chloride, respectively. The detection limits of this method were 1.8 ng dm^?3 for arsenic and 9.4 ng dm^?3 for antimony in the case of 100-cm³ sample volumes. Therefore, it is suitable for determination of trace arsenic and antimony in natural waters.     

Selective Sorption–Spectrometric Determination of Nanogram Amounts of Vanadium(IV) and Vanadium(V)

Conditions of the selective sorption–spectrometric determination of vanadium(IV) and vanadium(V) using sulfonitrophenol M were found. The determination of vanadium (visual test (RSD = 30%) using a reference color scale or quantitative determination (RSD < 10%) by diffuse reflectance spectra is performed immediately after the dynamic-mode sorption of its colored complexes with sulfonitrophenol M at pH 3.5 (vanadium(IV)) or with sulfonitrophenol M and hydroxylamine at pH 1.5 (vanadium(V), 650 nm) at the surface of polyamide membrane disks (d= 1 cm, l= 0.1 mm, m= 2.7 mg). The flow rate is 10–20 mL/min. The detection limit is 5–7 ng of vanadium in the support zone or 0.2–0.5 ng/mL. The determination of 0.5–5 ng/mL vanadium(V) at pH 1.5 does not interfere with 20-fold amounts of V(IV) and 1000-fold amounts of Ni, Zn, Cd, Mg, Co, Cr(III), Mn, PO^3- ₄, and F^–.     

Determination of Trace Chloroanilines in Environmental Water Samples Using Hollow Fiber-Based Liquid Phase Microextraction

A liquid phase microextraction method using hollow fiber to support extraction solvent was developed for enrichment of trace level chloroanilines in environmental water samples. Target analytes, 2-chloroaniline, 3-chloroaniline, 2,3-dichloroaniline, 2,4-dichloroaniline, 3,4-dichloroaniline, and 3,5-dichloroaniline were determined using gas chromatography-flame ionization detector after extraction. Experimental conditions that affect extraction efficiency were investigated and optimized. The proposed method showed a wide linear range from lower ??g L^?1 to 1,000 ??g L^?1, low detection limits (??5.1 ??g L^?1), and reasonable relative standard deviations (RSDs < 13%). Feasibility of the method was evaluated by analyzing river water samples collected from the Hudson River and the East River in New York City.     

Determination of Trace Amounts of Acetaldehyde Using a Novel Chemiluminescence Reaction

Abstract

The chemiluminescent reaction of iso-propyl alcohol with C10^?-H₂O₂ is enhanced by acetaldehyde. This provides a new method for the determination of trace amounts of acetaldehyde. The detection limit is 0.08ng/ml acetaldehyde and the linear dynamic range is 0.5ng/ml to 1000 ng/ml. The method results in good selectivity and has been satisfactorily applied to the determination of traces of acetaldehyde in waste water samples.     

Determination of copper,nickel, manganese and cadmium ions in aqueous samples by flame atomic absorption spectrometry after simultaneous coprecipitation with Co(OH)2

A separation-preconcentration procedure was developed for the determination of trace amounts of copper, nickel, manganese and cadmium ions in water samples by flame atomic absorption spectrometry after coprecipitation by Co(OH)₂ as a carrier without a chelating agent. The influence of the various analytical parameters such as pH, amount of carrier reagent, standing time, centrifugation rate and time, sample volume and matrix effects on the recovery of the analyte ions was studied. Under the specified experimental conditions the calibration curves for Ni(II) and Cu(II) were linear from 0.5 to 200 ng mL^?1 and for Mn(II) and Cd(II) from 0.5 to 250 and 0.3 to 80 ng mL^?1, respectively. The relative standard deviations for seven replicate determinations of a mixture of 40.0 ng mL^?1 of Cu(II), Ni(II), Mn(II) and 20 ng mL^?1 of Cd(II) in the original solution were 1.9%, 1.7%, 1.8% and 2.1%, respectively. The detection limits based on 3S_b/m for Cu(II), Ni(II), Mn(II) and Cd(II) in the original solution were 0.2, 0.2, 0.3 and 0.07 ng mL^?1, respectively. The limits of quantification based on 10S_b/m for Cu(II), Ni(II), Mn(II) and Cd(II) in the original solution were 6.7, 6.7, 10.0 and 2.3 ng mL^?1, respectively. The proposed method has been applied to the determination of trace amounts of the analyte ions in two certified reference materials (the National Institute for Environment Studies (NIES) No. 1 Pepperbush and NIES No. 7 Tea Leaves) and water samples and satisfactory results were obtained.     

Residue analysis of ethylenethiourea in vegetables by high-performance liquid chromatography with amperometric detection

Summary A method for the residue analysis of ethylenethiourea (ETU) in vegetables by HPLC with amperometric detection was developed. ETU was separated with Nucleosil C₁₈ as stationary phase and methanol-water (5:95, v/v) containing 0.05 mol/l ammonium acetate as eluent. The voltage of the working electrode (glassy carbon) was set at +1150 mV vs. Ag/AgCl. The limit of detection for ETU was found to be 0.3 ng. The method was applied to the determination of trace amounts of ETU in tomatoes and cucumbers. The minimum quantitation level was 0.01 ppm. The method can be performed easily; it is selective and highly sensitive.     

Determination of trace molybdenum in biological and water samples by graphite furnace atomic absorption spectrometry after separation and preconcentration on immobilized titanium dioxide nanoparticles

A new method has been developed for the determination of trace molybdenum based on separation and preconcentration with TiO₂ nanoparticles immobilized on silica gel (immobilized TiO₂ nanoparticles) prior to its determination by graphite furnace atomic absorption spectrometry (GFAAS). The optimum experimental parameters for preconcentration of molybdenum, such as pH of the sample, sample flow rate and volume, eluent and interfering ions, have been investigated. Molybdenum can be quantitatively retained by immobilized TiO₂ nanoparticles at pH 1.0 and separated from the metal cations in the solution, then eluted completely with 0.5 mol L^?1 NaOH. The detection limit of this method for Mo was 0.6 ng L^?1 with an enrichment factor of 100, and the relative standard deviation (RSD) was 3.4% at the 10 ng mL^?1 Mo level. The method has been applied to the determination of trace amounts of Mo in biological and water samples with satisfactory results.     

Combination of liquid-phase hollow fiber membrane microextraction with gas chromatography-negative chemical ionization mass spectrometry for the determination of dichlorophenol isomers in water and urine

A method for the determination of trace amount of dichlorophenol isomers in urine samples using the combination of liquid-phase hollow fiber microextraction (LPME-HF) with gas chromatography-negative chemical ionization mass spectrometry (GC-NCI-MS) has been demonstrated. The method has been optimized with respect to several parameters including the effects of negative chemical ionization (NCI) reagent pressure, the hollow fiber length, extraction time, stirring rate, sample pH and salt concentration for the determination of dichlorophenol isomers in water. The correlation coefficient (r²) of the calibration curves for 2,5-dichlorophenol, 2,3-dichlorophenol, 2,6-dichlorophenol, 3,5-dichlorophenol and 3,4-dichlorophenol were 0.988, 0.981, 0.985, 0.971 and 0.994, respectively. The average recovery rates for 2,5-dichlorophenol, 2,3-dichlorophenol, 2,6-dichlorophenol, 3,5-dichlorophenol and 3,4-dichlorophenol were 0.97, 0.93, 0.96, 0.95 and 0.95, respectively (n = 3 for each dichlorophenol) indicate that the methodology is feasible for the determination of trace amounts of dichlorophenol isomers in water and urine samples. Limits of detection (LOD) have been found to be in the range of 5-20 ng/ml. In addition, differentiation of the five dichlorophenol isomers is an easy task using the current approach of combining LPME-HF with NCI-GC-MS technique since they exhibit different NCI spectra.     

Construction and Application of an Electrochemical Sensor for Simultaneous Determination of Cd(II), Cu(II) and Hg(II) in Water and Foodstuff Samples

By incorporation of synthesized magnetite nanoparticles (Fe₃O₄ NPs) coated with a new Schiff base into carbon paste electrode, a novel modified electrode was constructed for simultaneous determination of ultra trace amounts of Cd(II), Cu(II) and Hg(II). The complexation reaction of Schiff base with metal ions was studied spectrophotometrically. Under optimal conditions a detection limit of 0.20, 0.90 and 1.00 ng mL^?1 for Cd(II), Cu(II) and Hg(II), respectively, was obtained. We take the advantages of the proposed method for simple, rapid, sensitive and selective simultaneous determination of trace amounts of hazardous Cd(II), Cu(II) and Hg(II) in water and foodstuff samples.     

Preconcentration by coprecipitation of arsenic and tin in natural waters with a Ni–pyrrolidine dithiocarbamate complex and their direct determination by solid-sampling atomic-absorption spectrometry

A method for the determination of trace amounts of arsenic and tin in natural waters is described. Trace amounts of arsenic and tin were preconcentrated by coprecipitation with a Ni–ammonium pyrrolidine dithiocarbamate (APDC) complex. The coprecipitates obtained were directly analyzed by graphite-furnace atomic-absorption spectrometry (GFAAS) using the Ni–APDC complex solid-sampling technique. The coprecipitation conditions used for the trace amounts of arsenic and tin in natural water were investigated in detail. It was found that arsenic and tin at sub-ng mL^–1 levels were both coprecipitated quantitatively by Ni(PDC)₂ in the pH range 2–3. The concentration factors by coprecipitation reached approximately 40,000 when 2 mg nickel was added as a carrier element to 500 mL of the water sample. The proposed method has been applied to the determination of trace amounts of arsenic and tin in river water and seawater reference materials, and the detection limits for arsenic and tin, which were calculated from three times of the standard deviation of the procedural blanks, are 0.02 ng mL^–1 and 0.04 ng mL^–1, respectively, for 500-mL volumes of water sample.     

Determinaton of trace amounts of titanium by flame atomic absorption spectrometry after cloud point extraction

In this work a cloud-point extraction has been used for the preconcentration of the trace amounts of titanium after complex formation with morin (2′,3,4′,5,7-pentahydroxyflavone) using Triton X-114 as surfactant. The chemical variables affecting the phase separation and the viscosity affecting the detection by flame atomic absorption spectrometry (FAAS) were optimized. At pH 4.5, preconcentration of 50 mL of sample in the presence of 0.08% Triton X-114 and 1.0 × 10^?4 M morin enabled the detection limit (c _L = 3S _b/m) of 2.9 ng/mL titanium and linear range 0.02–2.0 μg/mL to be achived. The preconcentration factor was 61, and the relative standard deviation was 3.8% for 0.1 μg/mL solution of Ti(IV) by repeated assays (n = 9). The proposed method has been applied to the determination of titanium in well water, spiked water and plant (Haloxylon).     

Sensitive determination of nitrite by means of a Landolt-type reaction in fluorescent aggregates of a binaphthyl-based amphiphile

The iodine quenching effect on the fluorescence of a binaphthyl-based amphiphile, C₈BNC₆N, was used for monitoring the Landolt-type reaction between nitrite, iodide, and thiosulfate. Due to the possibility of iodine detection in the 10^–8–10^–7 M range, and to the effective concentration of anionic reagents on the surface of cationic aggregates, the indicator reaction can be monitored using reagents at concentration levels as low as 10^–7 M. To optimize the analytical system, the effect of pH and reagent concentrations on the rate of indicator reaction were studied. The influence of the matrix of water samples and effect of side-reactions increasing the value of a blank test were examined. A procedure for nitrite determination in water was developed, using the diazo reaction for selective nitrite removal to provide a reference solution, which avoided possible effects of the matrix components. The usefulness of this method was tested by determining trace amounts of nitrite in water samples. The procedure allows determination of nitrite down to 5 ng/ml (detection limit about 2ng/ml) with r.s.d. of 10% in the 20–250 ng/ml range.     

Novel monohydrogenphosphate sensor based on vanadyl salophen

A novel PVC-based membrane sensor based on vanadyl salophen (VNSP) for determination of trace amounts of monohydrogenphosphate (MHP) ions is introduced. The electrode revealed Nernstian response towards monohydrogenphosphate over the wide concentration range from 1.0×10⁻¹ to 1.0×10⁻⁶ M at the pH of 8.2. The effect of solvent mediator, cationic additives and amount of ion-carrier on the behavior of the sensor was investigated. The sensor shows a short response time (<20 s) in the whole concentration ranges. The selectivity of the electrode is very high, and it can be used for detection of trace amounts of monohydrogenphosphate in the presence of large amounts of other anions. The detection limit of the electrode was 5.0×10⁻⁷ M (48 ng/ml) and it could be used for 14 weeks without any measurable changes in the slope. The potentiometric selectivity coefficients data revealed negligible interference from 16 common anions. It was successfully applied for the direct determination of monohydrogenphosphate in fertilizer samples and, as an indicator electrode, in potentiometric titration of HPO₄²⁻ ion with barium nitrate.     

The catalytic adsorptive stripping voltammetric determination of chromium with TTHA and nitrate

A sensitive voltammetric method is presented for the determination of trace amounts of total chromium (Cr(III) and Cr(VI)) in natural waters, employing the square wave mode. The method is based on the preconcentration of the Cr(III)-TTHA complex by adsorption at the HMDE at the potential of –1.0 V vs. Ag/AgCl. The adsorbed complex is then reduced producing a response with a peak potential of –1.29 V and the peak height of the Cr(III) reduction is measured. The catalytic action of the nitrate ions on the Cr(III)-TTHA reduction has been elucidated using cyclic voltammetry. The adsorption of chromium complexes at the HMDE was investigated using out-of-phase a.c. voltammetry and the potential range of adsorption was determined.Based on these investigations optimal conditions for the determination of the total chromium concentration in the range 155–2000 ng 1^–1 have been established. The determination limit is 15 ng 1^–1 and the RSD is 3.5% for chromium concentrations 200 ng 1^–1.The usefulness and wide scope of this method for reliable and highly sensitive chromium analysis down to the ultra trace levels existing in various types of natural waters is demonstrated by determinations of the total chromium content in lake, sea and rain water.     

ICP-MS法测定高纯钛中痕量元素

建立了ICP-MS直接测定高纯钛中Be,V,Co,Ni,Ga,Mo,Nb,Cd,Sb,TI,Pb的分析方法,并对ICP-MS工作参数及条件进行了优化和选择.高纯钛用HF与HNO3溶解后加入Sc、Cs、Re内标,用ICP-MS直接检测.方法的检出限为0.03～0.1 ng/mL,测定下限为0.2～0.5 ng/mL,各元...     

Catalytic kinetic spectrophotometric determination of trace amounts of palladium with dahlia violet after separation and preconcentration on sulphydryl dextran gel

A sensitive and selective kinetic catalytic spectrophotometric method has been described for the determination of trace amounts of palladium(II). The method is based on the catalytic effects of palladium(II) on the reduction reactions of Dahlia Violet with sodium dihydrogen hypophosphite (NaH₂PO₂) in a sulfuric acid medium. Under optimal conditions, trace amounts of palladium(II) can be determined. A good linear range has been obtained in the concentration range of Pd(II) over 0.001–0.028 μg/mL with a detection limit of 5.9 × 10⁻¹⁰ g/mL. The method has been successfully applied to the determination of palladium(II) in ore and soil samples. The relative standard deviation was less than 5.0% (n = 11). The coexisting ions were eliminated by preconcentration and separation on sulphydryl dextran gel with satisfactory results. The text was submitted by the authors in English.     

Flow-injection spectrophotometry of vanadium by catalysis of the bromate oxidation of N,N'-bis(2-hydroxyl-3-sulfopropyl)-tolidine

A highly sensitive flow-injection method is proposed for the catalytic determination of vanadium(V) at sub-nanogram per milliliter levels using a new indicator reaction. The method is based on the catalytic effect of vanadium(V) on the bromate oxidation of N,N′-bis(2-hydroxyl-3-sulfopropyl)-tolidine. 1,2-Dihydroxybenzene-3,5-disulfonate was used as an activator in the vanadium(V)-catalyzed reaction and significantly enhanced the sensitivity of the method. Vanadium(V) in the range 0.01-3.0 ng ml⁻¹ was easily determined with sampling rate of about 30 h⁻¹. Vanadium(IV) could be also determined. The limit of detection (S/N=3) was 0.008 ng ml⁻¹ and the relative standard deviations were 1.4 and 1.6% for ten determinations of 0.2 ng ml⁻¹ vanadium(IV) and vanadium(V), respectively. Interferences from metal ions could be suppressed by the addition of ethylenediamine-N,N,N′,N′-tetrakis(methylenephosphonic acid) as a masking agent. The proposed method was successfully applied to the determination of vanadium in water samples.     

Highly Sensitive and Selective Determination of Manganese in Tea Leaves by a Catalytic Kinetic Spectrophotometric Method

The catalytic effect of manganese(II) on the oxidation of barium diphenylamine sulfonate (BDAS) with potassium bromate in sulfuric acid was studied. Progress of the reaction was monitored, spectrophotometrically, by measuring absorbance changes at 547.5 nm. A highly sensitive, selective and simple method was accordingly developed for the determination of trace amounts of Mn(II), with no need for a separation or pre‐concentration step. Effects of reaction time, concentration of reagents, temperature and ionic strength on the reaction rate were studied. In the optimized conditions, manganese could be determined in a range of 1 to 60 ng mL^?1 with a detection limit of 0.2 ng mL^?1. The proposed method was successfully applied to the determination of manganese in tea leaves.     

Differential pulse voltammetric determination of P(V) following adsorptive accumulation of alpha-[PMo(12)O(40)](3-) on a polypyrrole-modified glassy carbon electrode

On the basis of the formation and pre-concentration of an α-Keggin-type [PMo₁₂O₄₀]³⁻ complex, a novel voltammetric method was developed for the determination of trace levels of P(V). The α-[PMo₁₂O₄₀]³⁻ complex was formed by heating a 5×10⁻⁴ M Mo(VI)-0.2 M HCl-40% (v/v) CH₃CN system containing a trace amount of P(V) at 70 °C for 30 min. During the electrochemical polymerization of pyrrole in the α-[PMo₁₂O₄₀]³⁻ solution, the α-[PMo₁₂O₄₀]³⁻ complex was accumulated into the polypyrrole film on a glassy carbon electrode. The differential pulse voltammetric peak current due to the α-[PMo₁₂O₄₀]³⁻ complex incorporated in the polypyrrole film was linearly dependent on the P(V) concentration in the range of 5×10⁻⁹-5×10⁻⁷ M; a detection limit of 2×10⁻⁹ M was achieved.