Determination of nitrobenzene by differential pulse voltammetry and its application in wastewater analysis

A new method for the determination of nitrobenzene (NB) by differential pulse voltammetry (DPV) based on an adsorptive stripping technique was developed. Cyclic voltammetry (CV) was used in a comparative investigation into the electrochemical reduction of NB at a glassy carbon electrode (GCE). With this electrode, the sharp peak of NB appeared at −0.71 V (vs. Ag/AgCl). The experimental parameters were optimized. Studies on the effect of pH on the peak height and peak potential were carried out over the pH range ca. 9.0–11.5 with sodium carbonate/sodium hydrogen carbonate buffer solution. A solution of pH 9.9 was chosen as analytical medium. Cathodic peak currents were found to be linearly related to the concentration of NB over the range ca. 12.3–1.23 × 10⁴ μg L⁻¹ with relative standard deviations of ca. 3.26–6.75%. The detection limit of NB in water was 5.42 μg L⁻¹. The interference of organic and inorganic species on the voltammetric response was also studied. The proposed method was applied to the determination of NB in wastewater samples with an average recovery of ca. 95.9–102.4%.     

Electrochemical studies on the interaction of heparin with crystal violet and its analytical application

In this paper, crystal violet (CV) was used to determine heparin concentration by linear sweep voltammetry on a dropping mercury electrode (DME). In Britton-Robinson (B-R) buffer solution, pH 3.0, CV had a well-defined second-order derivative linear sweep voltammetric reductive wave at −0.74 V (vs. SCE). After the addition of heparin to the CV solution, the reductive peak current decreased greatly with the positive movement of the peak potential and without appearance of new peaks in the scanning potential range. Based on the decrease in the reductive peak current, a new voltammetric method for the determination of heparin was established. The conditions for the interaction and the electrochemical detection were optimized, and interfering substances were investigated. Under the optimal conditions, the decrease in reductive peak currents of CV was proportional to heparin concentration in the range 0.1–8.0 mg/L with the linear regression equation Δip″(nA) = 400.42 + 1563.11c (mg/L), (n = 14, γ = 0.993). The detection limit was 0.092 mg/L. This new method was further successfully applied to the determination of heparin content in heparin sodium injection samples with satisfactory results. The binding ratio and binding mechanism were also studied by the electrochemical method. The text was submitted by the authors in English.     

Spectrophotometric multicomponent analysis of a mixture of chlorhexidine hydrochloride and lidocaine hydrochloride in pharmaceutical formulation using derivative spectrophotometry and partial least-squares multivariate calibration

Two spectrophotometric methods were applied to the simultaneous assay of chlorhexidine hydrochloride (CHL) and lidocaine hydrochloride (LIH) in pharmaceutical formulations. Using derivative spectrophotometry, CHL was determined by measurement of its first derivative signal at 290 nm (peak to zero amplitude) in the concentration range 5–9 μg/mL, and LIH was analysed by measurement of its second derivative signals at 272 and 276 nm (peak to peak amplitude) in the concentration range 160–480 μg/mL. With the partial least-squares (PLS-2), the experimental calibration matrix was constructed using 9 samples. The concentration ranges considered were 5–7 μg/mL for CHL and 220, 240, 260 μg/mL for LIH. The absorbances were recorded between 240 and 310 nm at every 5 nm.     

A simple linear sweep voltammetric method for the determination of double-stranded DNA with malachite green

In pH 3.5 Britton—Robinson buffer solution double-stranded (ds) DNA can react with malachite green (MG) to form an interaction complex, which resulted in the decrease of the electrochemical response of MG, MG had a well-defined second-order derivative linear sweep voltammetric peak at −0.73 V (vs. SCE). After the addition of dsDNA into MG solution, the reductive peak current decreased with the positive shift of peak potential, which was the typical characteristic of intercalation. Based on the interaction, an indirect electrochemical determination method for dsDNA was established. The optimum conditions for the reaction were investigated and there were little or no interferences from the commonly coexisting substances. The decrease of peak current was linear with the concentration of dsDNA over the range of 0.8–12.0 μg cm⁻³ with the linear regression equation as ΔI _p″/nA = 91.70 C/(μg cm⁻³) + 74.55 (n = 10, γ = 0.990). The detection limit was calculated as 0.46 μg cm⁻³ (3σ). The method had high sensitivity and was further applied to the dsDNA synthetic samples with satisfactory result. The interaction mechanism was discussed with the intercalation of DNA-MG to form a supramolecular complex and the stoichiometry of the supramolecular complex was calculated by electrochemical method with the binding number 3 and the binding constant 2.35 × 10¹⁵ (mol dm⁻³)⁻³.     

Fabrication of poly(orthanilic acid)–multiwalled carbon nanotubes composite film-modified glassy carbon electrode and its use for the simultaneous determination of uric acid and dopamine in the presence of ascorbic acid

A multiwalled carbon nanotubes (MWNT) modified glassy carbon electrode (GCE) coated with poly(orthanilic acid) (PABS) film (PABS–MWNT/GCE) has been fabricated and used for simultaneous determination of dopamine (DA) and uric acid (UA) in the presence of ascorbic acid (AA) by differential pulse voltammetry (DPV). Scanning electron microscopy, Fourier transform infrared spectra, and electrochemical techniques have been used to characterize the surface morphology of the PABS–MWNT composite film and the polymerization of ABS on electrode surface. In comparison with the bare GCE and the MWNT-modified GCE, the PABS–MWNT composite film-modified GCE, which combines the advantages of MWNT and the self-doped PABS, exhibits good selectivity and sensitivity for the simultaneous and selective determination of UA and DA in the presence of AA. Due to the different electrochemical responses of AA, DA, and UA, PABS–MWNT/GCE can resolve the overlapped oxidation peak of DA and UA into two well-defined voltammetric peaks with enhanced current responses using both cyclic voltammetry (CV) and DPV. The peak potential separations between DA and UA are 170 mV using CV and 160 mV using DPV, respectively, which are large enough for the selective and simultaneous determination of these species. In the presence of 0.5 mM AA, the DPV peak currents are linearly dependent on the concentration of UA and DA in the range of 6–55 and 9–48 μM with correlation coefficients of 0.997 and 0.993, respectively. The detection limits (S/N = 3) for detecting UA and DA are 0.44 and 0.21 μM, respectively. The PABS–MWNT/GCE shows good reproducibility and stability and has been used for the simultaneous determination of DA and UA in the presence of AA in samples with satisfactory results.     

Anodic voltammetric behavior of ascorbic acid and its selective determination in pharmaceutical dosage forms and some Rosa species of Turkey

Ascorbic acid is the most common electroactive biological compound found in some plant species (e.g., Citrus species, Rosa species). The electrochemical oxidation of ascorbic acid was investigated by cyclic, linear sweep, differential pulse (DPV), and square wave (SWV) voltammetry. For analytical purposes, a very well-resolved diffusion-controlled voltammetric peak was obtained in acetate buffer at pH 3.50 for DPV and SWV. The linear response was obtained in the range of 3.52–176.1 μg/mL with a detection limit of 0.88 μg/mL for DPV and 0.52 μg/mL for SWV. Based on this study, simple, rapid, selective, and sensitive voltammetric methods were developed for the determination of ascorbic acid in pharmaceutical dosage forms and Rosa species (R. dumalis ssp. boissieri var. boissieri, R. canina, R. pulverulenta, R. heckeliana ssp. vanheurckiana, and R. montana subsp. woronowii). The results obtained are compared with the HPLC data. The developed methods enable the extracts to be analyzed without the necessity of any time-consuming separation. The text was submitted by the authors in English.     

High-Speed Large Scale Chromatographic Purification of Plasmid DNA with a Novel Giant-Pore Stationary Phase

A rigid spherical giant-pore poly (glycidyl methacrylate-co-ethylene dimethacrylate) matrix has been prepared by radical suspension–polymerization on the basis of a novel porogenic mode using superfine particles of calcium carbonate as a solid porogen. Scanning electron microscopy reveals that the bead has pores as large as 10 μm. The hydrodynamic properties show that this polymeric material has good strength and a low back pressure of 1.0 MPa at a flow velocity of 3,000 cm h⁻¹. After being modified to be an anion-exchange material, high dynamic binding capacity of plasmid DNA of above 1,000 μg plasmid per mL of bed by a column of this material, could be obtained comparing to the 150 μg plasmid per mL of bed with a Q-Sepharose FF column at the same flow rate. Large-scale preparative plasmid separations (2–20 mL) from cell lysate were investigated. A 75% yield and 94.9% purity of SC plasmid DNA were obtained by a 20 mL column of giant-pore beads at a flow rate of 600 cm h⁻¹.     

Electrochemical behavior and differential pulse voltammetric determination of paracetamol at a carbon ionic liquid electrode

The electrochemical behavior of paracetamol in 0.1 M acetate buffer solution (pH 4.6) was investigated at a traditional carbon paste electrode (TCPE) and a carbon ionic liquid electrode (CILE) fabricated by replacing nonconductive organic binders with a conductive hydrophobic room temperature ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate (BmimPF₆). The results showed that the CILE exhibited better reversibility for the electrochemical redox of paracetamol. The oxidation potential of paracetamol at the CILE is +0.462 V, which is approximately 232 mV lower than that at the TCPE; the oxidation peak current response is nine times higher than that at the TCPE. The differential pulse voltammetric determination of paracetamol at the CILE was established based on this behavior. After optimizing several important parameters controlling the performance of paracetamol at the CILE, the oxidation peak current versus paracetamol concentration at the CILE showed linearity in the range from 1.0 μM to 2.0 mM (R ²  = 0.9992) with a detection limit of 0.3 μM (S/N = 3). The method has been applied to the determination of paracetamol in tablets and urine samples and the average recovery of paracetamol was 98.5% and 99.3%, respectively. The proposed CILE showed good sensitivity and reproducible response without influence of interferents commonly existing in pharmaceutical and urine samples. Figure CV curves of paracetamol illustrate the enhanced electrochemical behavior of paracetamol at the CILE (b), which forms the basis for the differential pulse voltammetric determination of paracetamol     

Electrochemical behavior of nicotinamide using carbon paste electrode modified with macrocyclic compounds

The electrochemical behavior of nicotinamide was studied at a carbon paste electrode and the electrodes modified with macrocyclic compounds using voltammetric and impedance measurements. The electrodes so formed were able to bind nicotinamide ions chemically and gave better voltammetric responses than the unmodified ones. The macrocycles used as modifiers for the electrode preparation were 18-crown-6, dicyclohexano-18-crown-6, dibenzo-18-crown-6, 7,16-dibenzyl-1,4,10,13-tetraoxa-7,16-diazacyclooctadecane, 1,4,7,10,13,16-hexathiacyclooctadecane (Hexathia), 1,4,7,10-tetratosyl-1,4,7,10-tetraazacyclododecane, 1,4,8,11-tetraazacyclooctadecane, c-Methylcalix[4]resorcenarene and calix[8]arene. Among these macrocyclic modified electrodes, hexathia showed more affinity towards nicotinamide and a 2.3-fold increase in voltammetric signal was obtained. Impedance measurement was used to confirm this enhancement observed on modified electrode. This increase in anodic peak current was then used for finding linear working range, which was 0.1–500 μg mL⁻¹ with a detection limit of 0.03 μg mL⁻¹ by DPV. Interference from other vitamins like thiamine HCl (Vit. B₁), riboflavin (Vit. B₂), pyridoxine HCl (Vit. B₆) cynocobamine (Vit. B₁₂), para-aminobenzoic acid (PABA) and ascorbic acid (Vit. C) was also studied. The modified electrode could be used for the simultaneous determination of riboflavin, nicotinamide and pyridoxine HCl. It has also been utilized for the analysis of nicotinamide in pharmaceutical preparations.     

Linear sweep voltammetric studies on the interaction of brilliant cresyl blue with nucleic acids and its analytical application

In this paper, the interaction of brilliant cresyl blue (BCB) with nucleic acids was studied and further applied for the microdetermination of nucleic acids. In aqueous Britton-Robinson (B-R) buffer solution, BCB can be easily reduced on the hanging mercury drop electrode (HMDE) and had a sensitive voltammetric reduction peak at -0.09 V (vs. SCE). The reduction peak current of BCB could be greatly decreased by the addition of DNA. The results of voltammetric measurements had indicated that a binding reaction was occurred between BCB and DNA and a new supramolecular complex was formed, which resulted in the decrease of the diffusion coefficient of the reaction solution and the decrease of the reduction peak current correspondingly. The conditions of interaction and the electrochemical detection were carefully investigated. Under the selected conditions, the calibration curves for the detection of fish sperm (fs)DNA, calf thymus (ct)DNA and yeast (y)RNA were established. The linear range of this assay was 1.0-30.0 microg/mL for fsDNA, 1.0-45.0 microg/mL for ctDNA and 1.0-25.0 microg/mL for yRNA, respectively. The detection limits were 0.38 microg/mL fsDNA, 0.43 microg/mL ctDNA, 0.64 microg/mL yRNA. The interaction parameters such as the equilibrium constant and the binding number were calculated by electrochemical method. The results showed that the 2:3 type of complex was formed in the fsDNA-BCB complex with the binding constant as 2.51 x 10(7). The proposed method was further applied to the synthetic samples determination with satisfactory results.     

A new sensor for electrochemical determination of captopril using chlorpromazine as a mediator at a glassy carbon electrode

A new simple, selective and rapid cyclic voltammetric method is reported for the accurate and precise determination of captopril using chlorpromazine as a suitable electrocatalyst. It has been shown by cyclic voltammetry, single step chronoamperometry and electrochemical impedance spectroscopy that chlorpromazine can catalyze the oxidation of captopril in aqueous buffer solution and produces a sharp oxidation peak current at about 0.625 V vs. saturated calomel reference electrode. The catalytic oxidation peak current of captopril is linearly dependent on its concentration and enables the determination of captopril over the concentration range of 8–1000 μM at pH 5.0, with a detection limit of 4.8 μM. The relative standard deviation for the determination of 400 μM captopril is 0.66% (n = 9). The influence of potential interfering substances on the determination of captopril was studied. The method was satisfactorily applied to the determination of captopril in real samples such as drug and urine.     

Electrochemical preparation, characterization, and electrocatalytic studies of Nafion–ruthenium oxide modified glassy carbon electrode

Electrochemical synthesis of ruthenium oxide (RuOx) onto Nafion-coated glassy carbon (GC) electrode and naked GC electrode were carried out by using cyclic voltammetry. Electrochemical deposition of RuOx onto Nafion-coated electrode was monitored by in situ electrochemical quartz crystal microbalance (EQCM). Surface characterizations were performed by scanning electron microscope (SEM) and atomic force microscope (AFM). SEM and AFM images revealed that ruthenium oxide particles incorporated onto the Nafion polymer film. In addition, a GC electrode modified with ruthenium oxide–Nafion film (RuOx–Nf–GC) was shown excellent electrocatalytic activity towards dopamine (DA) and ascorbic acid (AA). The anodic peak current increases linearly over the concentration range of 50 μM–1.1 mM for DA with the correlation coefficient of 0.999, and the detection limit was found to be (S/N = 3) 5 μM. Owing to the catalytic effect of the modified film towards DA, the modified electrode resolved the overlapped voltammetric responses of AA and DA into two well-defined voltammetric peaks with peak-to-peak separation about 300 mV. Here, RuOx–Nf–GC electrode employed for determination of DA in the presence of AA. This modified electrode showed good stability and antifouling properties.     

Molecularly imprinted polymer solid-phase extraction coupled to square wave voltammetry at carbon fibre microelectrodes for the determination of fenbendazole in beef liver

A molecularly imprinted polymer was developed and used for solid-phase extraction (MISPE) of the antihelmintic fenbendazole in beef liver samples. Detection of the analyte was accomplished using square wave voltammetry (SWV) at a cylindrical carbon fibre microelectrode (CFME). A mixture of MeOH/HAc (9:1) was employed both as eluent in the MISPE system and as working medium for electrochemical detection of fenbendazole. The limit of detection was 1.9 × 10⁻⁷ mol L⁻¹ (57 μg L⁻¹), which was appropriate for the determination of fenbendazole at the maximum residue level permitted by the European Commission (500 μg kg⁻¹ in liver). Given that the SW voltammetric analysis could not be directly performed in the sample extract as a consequence of interference from some sample components, a sample clean-up with a MIP for selectively retaining fenbendazole was performed. The MIP was synthesized using a 1:8:22 template/methacrylic acid/ethylene glycol dimethacrylate ratio. A Britton–Robinson Buffer of pH 9.0 was selected for retaining fenbendazole in the MIP cartridges, and an eluent volume of 5.0 mL at a flow rate of 2.0 mL min⁻¹ was chosen in the elution step. Cross-reactivity with the MIP was observed for other benzimidazoles. The synthesized MIP exhibited a good selectivity for benzimidazoles with respect to other veterinary drugs. The applicability of the MISPE-SWV method was tested with beef liver samples, spiked with fenbendazole at 5,000 and 500 μg kg⁻¹. Results obtained for ten different liver samples yielded mean recoveries of (95 ± 12)% and (96 ± 11)% for the upper and lower concentration level, respectively.     

Development of automated amperometric detection of antibodies against <Emphasis Type="Italic">Bacillus anthracis</Emphasis> protective antigen

Picogram levels of antibodies against the protective antigen (PA) of Bacillus anthracis were detected in an automated electrochemical sandwich-type enzyme-linked immunosorbant assay. The antibodies were captured and detected using an 8 × 3 array of 50-μm-diameter cavities. The reagent and sample volumes were as low as 200 nL in a less than 25-min assay from capture to signal generation. The electrochemical detection of the antibodies was demonstrated at 0.05–10 μg/mL containing only 10–5,000 pg antibodies. The limit of detection is 10 fg for a 200-nL sample. Detection of anti-PA immunoglobulin G performed in spiked normal human serum and fresh whole human blood did not show a significant difference from detection in a buffer. The initial automation of the assay involved the use of a digital syringe pump for the delivery of reagents to the capture surface.     

Simultaneous Determination of Baicalin, Baicalein, Wogonin, Oxysophocarpine, Oxymatrine and Matrine in the Chinese Herbal Preparation of Sanwu-Huangqin-Tang by Ion-Paired HPLC

A sensitive and reliable ion-paired high-performance liquid chromatographic method has been established for the simultaneous quantification of six major active ingredients, namely baicalin, baicalein, wogonin, oxysophocarpine, oxymatrine and matrine in the Chinese herbal preparation, Sanwu-Huangqin-Tang. HPLC analyses were performed on a Phenomenex luna C₁₈ column with mobile phase of methanol–acetonitrile–aqueous phosphoric acid at a flow rate of 0.9 mL min⁻¹. The complete separation was achieved within 35 min for the six target constituents. A good linear regression relationship between peak-areas and concentrations was obtained over the range of 12.10–242.0 μg*mL⁻¹ for baicalin, 5.05–101.0 μg*mL⁻¹ for baicalein, 0.95–19.0 μg*mL⁻¹ for wogonin, 2.75–55.0 μg*mL⁻¹ for oxysophocarpin, 2.75–55.0 μg*mL⁻¹ for oxymatrine and 4.90–98.0 μg*mL⁻¹ for matrine, respectively. The repeatability was evaluated by intra- and inter-day assays with relative standard deviation (RSD) being less than 5.1%. The recoveries, measured at three concentration levels, varied from 93.8 to 102.1%. The assay was successfully applied for determination of six bioactive compounds in Sanwu-Huangqin-Tang. The interaction of chemical constituents was observed when the herbs were used in compatibility. The results indicated that the developed assay method was rapid, accurate and could be readily utilized as a quality control method for Sanwu-Huangqin-Tang.     

The immobilization of Cytochrome c on MWNT–PAMAM–Chit nanocomposite incorporated with DNA biocomposite film modified glassy carbon electrode for the determination of nitrite

A novel and sensitive biosensor was developed for the determination of nitrite. Firstly, multi-walled carbon nanotubes–poly(amidoamine)–chitosan (MWNT–PAMAM–Chit) nanocomposite along with the incorporation of DNA was used to modify the glassy carbon electrode. Then the immobilization of Cyt c was accomplished using electrochemical deposition method by consecutive cyclic voltammetry (CV) scanning in a neutral Cyt c solution. CV behaviors of the modified electrodes showed that the MWNT–PAMAM–Chit nanocomposite is a good platform for the immobilization of DNA and Cyt c in order, at the same time, an excellent promoter for the electron transfer between Cyt c and the electrode. At high potential, the immobilized Cyt c could be further oxidized into highly reactive Cyt c π-cation by two-step electrochemical oxidation, which could oxidize NO₂ ⁻ into NO₃ ⁻ in the solution. Therefore, a nitrite biosensor based on the biocatalytic oxidation of the immobilized Cyt c was fabricated, which showed a fast response to nitrite (less than 5 s). The linear range of 0.2–80 μM and a detection limit of 0.03 μM was obtained. Finally, the application in food analysis using sausage as testing samples was also investigated.     

Electrochemical Study of 4-Nitrophenol at a Modified Carbon Paste Electrode

 A zeolite-modified carbon paste electrode (CPE) has been used for the determination of 4-nitrophenol by differential pulse voltammetry (DPV). The electrochemical reduction of 4-nitrophenol at −1.0 V is carried out in a Britton-Robinson medium at pH 3.5. The cyclic voltammetric (CV) behaviour has been investigated to study the nature of the process. Studies on the effect of pH were carried out over the pH range 2–9 with the Britton-Robinson buffer solution, and the influence of pH on peak height and peak potential was analyzed. A linear relationship between peak intensity and concentration is obtained in the range 0.2–10 mg L⁻¹, with a detection limit of 0.04 mg L⁻¹; a relative standard deviation of 1.5% for a 5 mg L⁻¹ 4-nitrophenol concentration and a relative error of 2.6% were also obtained (n=11). Received March 3, 1998. Revision December 10, 1998.     

Development of a voltammetric procedure for assay of thebaine at a multi-walled carbon nanotubes electrode: quantification and electrochemical studies

The study of electrochemical behavior and determination of thebaine (THEB), an opiate alkaloid, is described on a multi-walled carbon nanotube (MWCNT) modified glassy carbon electrode by adsorptive stripping voltammetry and electrochemical impedance spectroscopy. The results indicated that MWCNT electrodes remarkably enhance electrocatalytic activity toward the oxidation of THEB in a wide pH range of 2.0–10.0, and it shows two irreversible and diffusion-controlled anodic peaks. Then, a sensitive, simple, and time-saving cyclic voltammetric procedure was developed for the analysis of THEB in human urine samples. Under optimized conditions, the oxidation peak has two linear dynamic ranges of 1.0–80.0 and 100.0–600.0 μM, with detection limit of 0.23 μM and a precision of <4% (relative standard deviation for eight analysis).     

HPLC Determination of DCJW in Rat Plasma and Its Application to Pharmacokinetics Studies

A high-performance liquid chromatography–UV method for determining DCJW concentration in rat plasma was developed. The method described was applied to a pharmacokinetics study of intramuscular injection in rats. The plasma samples were deproteinized with acetonitrile in a one-step extraction. The HPLC assay was carried out using a VP-ODS column and the mobile phase consisting of acetonitrile–water (80:20, v/v) was used at a flow rate of 1.0 mL min⁻¹ for the effective eluting DCJW. The detection of the analyte peak area was achieved by setting a UV detector at 314 nm with no interfering plasma peak. The method was fully validated with the following validation parameters: linearity range 0.06–10 μg mL⁻¹ (r > 0.999); absolute recoveries of DCJW were 97.44–103.46% from rat plasma; limit of quantification, 0.06 μg mL⁻¹ and limit of detection, 0.02 μg mL⁻¹. The method was further used to determine the concentration–time profiles of DCJW in the rat plasma following intramuscular injection of DCJW solution at a dose of 1.2 mg kg⁻¹. Maximum plasma concentration (C _max) and area under the plasma concentration–time curve (AUC) for DCJW were 140.20 ng mL⁻¹ and 2405.28 ng h mL⁻¹.     

Sequential injection technique for determination of phenoxybenzamine hydrochloride and metoclopramide in pharmaceutical formulations

A sequential injection analysis (SIA) system is described for the determination of phenoxybenzamine hydrochloride and metoclopramide using spectrophotometer as detector. The method is based on the detection of an unstable red intermediate compound resulting from the reaction of phenoxybenzamine hydrochloride or metoclopramide with the diazotizating product of p-phenylenediamine with sodium nitrite in hydrochloric acid medium. The sampling frequency is 69 h⁻¹ and 75 h⁻¹ for phenoxybenzamine hydrochloride and metoclopramide, respectively. The linear range is 10–400 μg/mL for phenoxybenzamine hydrochloride with a detection limit of 0.081 μg/mL and 20–250 μg/mL for metoclopramide with a detection limit of 0.034 μg/mL. The RSD is 1.01 and 0.45% for phenoxybenzamine hydrochloride and metoclopramide, respectively. The proposed methods were used to determine phenoxybenzamine hydrochloride and metoclopramide in pharmaceuticals. The results are compared with those obtained by pharmacopoeia method. The article is published in the original.