周期性应变调控斯格明子在纳米条带中的运动

斯格明子是一种拓扑稳定的手性自旋结构,凭借其在磁性赛道存储器和自旋电子器件方面的巨大应用潜力而受到研究人员的广泛关注.为了使斯格明子能够更好地应用于磁性赛道存储器,研究斯格明子在纳米条带中的运动行为就变得非常重要.本文主要研究了存在周期性应变的纳米条带中铁磁斯格明子和反铁磁斯格明子在电流驱动下的运动行为.研究结果表明:周期性应变使得驱动电流存在一个临界电流密度,只有当电流密度大于临界电流密度时斯格明子才能够在纳米条带中连续移动.临界电流密度随应变振幅的增加而增加,随应变周期的增加而减小.铁磁斯格明子在周期性应变的调制下会产生周期性运动,轨迹为波浪式,其横向速度受到边界的影响,而纵向速度则与应变梯度成正比.反铁磁斯格明子在周期性应变调控下运动方向不变,但其移动速度则剧烈变化.     

Fabrication of high quality chirped fiber Bragg grating by establishing strain gradient

To fabricate chirped fiber Bragg grating (CFBG) with high reflectivity and accurately controlled chirp profile with low cost, we develop the CFBG fabrication technique based on strain gradient: fabricating CFBG using fabricated fiber Bragg grating (FBG) by establishing strain gradient along the length of grating. We theoretically analyze the form of such CFBGs, and study the characteristics of gratings using piecewise-uniform approach. It is shown that increasing UV-induced index change or the length of the grating or both are the efficient ways to obtain high quality CFBG with high reflectivity and good reflection spectrum. The dispersion of this grating is decided by and varies inversely with the slope of the strain gradient along the length of the grating, not decided by UV-induced index change or by the length of grating. One can control the dispersion and the chirp profile by adjusting the slope of the strain gradient. Based on the theoretical analysis, we have fabricated CFBG whose reflectivity is maintained at 100% in a large range of strain gradients.     

光梯度力驱动纳谐振器的非线性动力学特性研究

光梯度力作为纳谐振器的一种新型驱动方式,得到了广泛关注.本文研究了光梯度力的固有非线性特性,建立了光梯度力驱动圆环与辐条谐振系统的动力学模型.揭示了入射光功率以及几何参数对系统的非线性动力学响应的影响规律.研究表明:光梯度力会引起系统呈现刚度软化效应,随着入射光功率增大,系统主共振峰值明显增大,且谐振频率随着振幅增大而产生较大偏移;两环初始间隙增大,系统振动幅值和谐振频率均下降;辐条厚度越大,系统主共振峰值和谐振频率均减小.因此,可以通过调节入射光功率来实现圆环辐条谐振器的频率调节,为光梯度力驱动纳谐振器动力学设计和性能预测提供理论参考.     

光梯度力驱动的纳米硅基光开关

通过一道光改变另一道光的传输路线是光子集成网络中重要而长远的目标, 然而, 由于硅材料的光学非线性较弱, 在硅材料上实现开关的全光控制难以实现. 因此本文提出了一种由光梯度力驱动的纳米硅基光开关, 实现了硅基光开关的全光控制. 该光开关由一个部分悬空的微环谐振器和一个交叉波导结构构成, 当通入一道控制光时, 悬空的微环谐振器在光梯度力的作用下发生弯曲, 微环谐振器的谐振波长随之发生变化, 从而实现光信号的传输路线发生改变. 该光开关利用纳米光子制造技术在标准绝缘体上硅晶圆上制造, 实验数据得出其最小消光比为10.67 dB, 最大串扰为 -11.01 dB, 开关时间分别为180 ns和170 ns. 该光开关具有尺寸小, 响应速度快, 低损耗和可拓展等优点, 在片上集成光路、高速信号处理以及下一代光纤通信网络中具有潜在应用.     

Velocity gradient driven flute instabilities in plasmas

The effect of velocity gradient across the magnetic field on the low frequency flute modes is examined in detail, using the normal mode analysis. It is shown that some new type of instabilities driven primarily by the velocitygradient arise and these excited modes eventually attain the convective saturation. The onset of plasma turbulence due to these instabilities may possibly be one of the major contributors for anomalous heating process and enhanced plasma resistivity.     

The nano scale vibration of protein microtubules based on modified strain gradient theory

This paper investigates the free vibration of protein microtubules (MTs) embedded in the cytoplasm by using linear and nonlinear Euler–Bernoulli beam model based on modified strain gradient theory. The protein microtubule is modeled as a simply support or clamped–clamped beam. Beside, the elastic medium surrounding of MTs is modeled with Pasternak foundation. Vibration equations are obtained by using Hamilton principle and these equations are solved according to boundary conditions. Finally the dependency of vibration frequencies on environmental conditions, MTs size, changes of temperature and material length scale parameters (size effects) is studied. By comparing the findings, it could be said that the MTs' frequency is greatly increased in the presence of cytoplasm and it is very dependent to material length scale parameters.     

Control of Hall angle of Skyrmion driven by electric current

Skyrmions are very promising for applications in spintronics and magnetic memory.It is desired to manipulate and operate a single skyrmion.Here we report on the thermal effect on the motion of current-driven magnetic Skyrmions in magnetic metal.The results show that the magnon current induced by the thermal gradient acts on Skyrmions via magnonic spin-transfer torque,an effect of the transverse and longitudinal Skyrmions drift velocities,thus leading to the effective manipulation of the Hall angle through the ratio of thermal gradient to electric current density,which can be used as a Skyrmion valve.     

梯度掺杂体异质结对有机太阳能电池光电转换效率的影响

基于传统的体异质结有机太阳能电池结构, 对结构中的混合层改用梯度掺杂的方法, 在AM1.5, 100 mW/cm²光照下, 使得器件的短路电流由原来的7.72 mA/cm²提高到了9.18 mA/cm², 相应的光电转换效率提高了25%. 器件性能的提升归因于梯度掺杂体系的引入使得体异质结混合层中同一材料分子之间形成了较好的连续网络结构, 降低了器件的串联电阻, 提高了电极对载流子的收集效率, 从而提高了器件的光电转换效率. 关键词： 有机太阳能电池 体异质结 梯度掺杂     

托卡马克离子温度梯度湍流输运同位素定标修正中杂质的影响

托卡马克实验发现,在不同参数条件下,等离子体能量约束经验定标律会有或大或小的修正.为解释这种修正现象发生的原因,应用回旋动理学方法,对含重(钨)杂质等离子体离子温度梯度(ITG)(包括杂质模)湍流输运的同位素效应进行了数值研究.结果表明钨杂质效应极大地修改了同位素定标律和有效电荷效应.随着杂质离子电荷数Z和电荷集中度f_z的变化,同位素定标律在较大范围内变化. ITG模最大增长率定标大约为M_i~(-0.48→-0.12),杂质模的定标为M_i~(-0.46→-0.3),其中, M_i表示主离子质量数.在ITG模湍流中,有效电荷数越大,关于M_i的拟合指数偏离-0.5越远,表现为同位素质量依赖减弱.在两种模中,杂质电荷集中度越大,同位素质量依赖越弱.研究了杂质效应使定标关系发生偏离的原因,证实杂质种类、杂质电荷数和杂质浓度的不同,是引起同位素质量依赖发生改变的重要原因.结果证实并解释了不同参数条件下托卡马克同位素定标的差异性.研究成果可以为ITER实验安排及杂质相关输运实验中选择装置材料、工作气体和设置其他参数提供理论参考.     

表面能梯度驱动下纳米水滴在不同微结构表面上的运动

近年来, 微观尺度下水滴在能量梯度表面上的运动情况受到了广泛关注, 然而通过实验进行研究尚存在困难. 本文利用分子动力学方法研究了不同微结构表面上纳米水滴在表面能梯度驱动下的运动情况. 结果表明: 槽状和柱状微结构可以明显提升纳米水滴在微结构表面上的运动效率, 钉状微结构会降低纳米水滴的运动效率, 尽管它具有稳定的疏水性; 结合槽状和钉状结构的混合状微结构兼具二者的优点, 不但可以有效地提高纳米水滴在粗糙表面上的运动效率, 而且具有比较高的疏水稳定性. 此外, 表面能的微小改变会明显影响水滴的运动效率.     

Viscoelastic wave propagation in the viscoelastic single walled carbon nanotubes based on nonlocal strain gradient theory

In this paper, the viscoelastic wave propagation in an embedded viscoelastic single-walled carbon nanotube (SWCNT) is studied based on the nonlocal strain gradient theory. The characteristic equation for the viscoelastic wave in SWCNTs is derived. The emphasis is placed on the influence of the tube diameter on the viscoelastic wave dispersion. A blocking diameter is observed, above which the wave could not propagate in SWCNTs. The results show that the blocking diameter is greatly dependent on the damping coefficient, the nonlocal and the strain gradient length scale parameters, as well as the Winkler modulus of the surrounding elastic medium. These findings may provide a prospective application of SWCNTs in nanodevices and nanocomposites.     

单轴应变驱动铁bcc—hcp相转变的微观模拟

用分子动力学方法模拟了沿〈001〉晶向应变加载和卸载情况下单晶铁中体心立方(bcc)与六方密排(hcp)结构的相互转变,分析了相变的可逆性和微结构演化特征.微观应力的变化显示样品具有超弹性性质,而温度变化表明在相变和逆相变过程中均出现放热现象.相变起始于爆发式均匀形核,晶核由块状颗粒迅速生长为沿{011}晶面的片状分层结构; 而卸载逆相变则从形核开始就呈现片状形态,且相界面晶面指数与加载相变完全一致,表现出形态记忆效应.在两hcp晶核生长的交界面易形成面心立方(fcc)堆垛层错. fcc通过在hcp晶粒内     

Wave propagation in viscoelastic single-walled carbon nanotubes with surface effect under magnetic field based on nonlocal strain gradient theory

The governing equation of wave motion of viscoelastic SWCNTs (single-walled carbon nanotubes) with surface effect under magnetic field is formulated on the basis of the nonlocal strain gradient theory. Based on the formulated equation of wave motion, the closed-form dispersion relation between the wave frequency (or phase velocity) and the wave number is derived. It is found that the size-dependent effects on the phase velocity may be ignored at low wave numbers, however, is significant at high wave numbers. Phase velocity can increase by decreasing damping or increasing the intensity of magnetic field. The damping ratio considering surface effect is larger than that without considering surface effect. Damping ratio can increase by increasing damping, increasing wave number, or decreasing the intensity of magnetic field.     

准一维纳米线电子输运的梯度无序效应

考虑实际体系的梯度无序和结散射,发展格林函数矩阵分解消元方法,研究了准一维纳米线的电子输运性质. 结果表明,由于结散射,电导随能量呈现振荡行为,无序的引入破坏了电子相干性,在低无序度区平均电导呈现异常增加,呈现一个新的电导峰. 当表面存在无序但无梯度衰减时,体系的平均电导随无序度增强先减后增,出现类局域-退局域性转变. 当表面无序线性衰减时,平均电导在强无序区稍有增加,而当表面无序高斯型衰减时,平均电导指数衰减,类局域-退局域性转变消失,不同于以前的理论预言. 研究结果对准一维纳米线电子器件的结构设计和应用有指导作用. 关键词： 准一维纳米线 梯度无序 电子输运     

Wave dispersion in viscoelastic single walled carbon nanotubes based on the nonlocal strain gradient Timoshenko beam model

Based on the nonlocal strain gradient theory and Timoshenko beam model, the properties of wave propagation in a viscoelastic single-walled carbon nanotube (SWCNT) are investigated. The characteristic equations for flexural and shear waves in visco-SWCNTs are established. The influence of the tube size on the wave dispersion is clarified. For a low damping coefficient, threshold diameter for shear wave (SW) is observed, below which the phase velocity of SW is equal to zero, whilst flexural wave (FW) always exists. For a high damping coefficient, SW is absolutely constrained, and blocking diameter for FW is observed, above which the wave propagation is blocked. The effects of the wave number, nonlocal and strain gradient length scale parameters on the threshold and blocking diameters are discussed in detail.     

Valley-dependent transport in strain engineering graphene heterojunctions

We study the effect of strain on band structure and valley-dependent transport properties of graphene heterojunctions. It is found that valley-dependent separation of electrons can be achieved by utilizing strain and on-site energies. In the presence of strain, the values of transmission can be effectively adjusted by changing the strengths of the strain, while the transport angle basically keeps unchanged. When an extra on-site energy is simultaneously applied to the central scattering region, not only are the electrons of valleys K and K' separated into two distinct transmission lobes in opposite transverse directions, but the transport angles of two valleys can be significantly changed. Therefore, one can realize an effective modulation of valley-dependent transport by changing the strength and stretch angle of the strain and on-site energies, which can be exploited for graphene-based valleytronics devices.     

Modulation of Schottky barrier in XSi2N4/graphene (X=Mo and W) heterojunctions by biaxial strain

Reducing the Schottky barrier height (SBH) and even achieving the transition from Schottky contacts to Ohmic contacts are key challenges of achieving high energy efficiency and high-performance power devices. In this paper, the modulation effects of biaxial strain on the electronic properties and Schottky barrier of MoSi₂N₄ (MSN)/graphene and WSi₂N₄ (WSN)/graphene heterojunctions are examined by using first principles calculations. After the construction of heterojunctions, the electronic structures of MSN, WSN, and graphene are well preserved. Herein, we show that by applying suitable external strain to a heterojunction stacked by MSN or WSN — an emerging two-dimensional (2D) semiconductor family with excellent mechanical properties — and graphene, the heterojunction can be transformed from Schottky p-type contacts into n-type contacts, even highly efficient Ohmic contacts, making it of critical importance to unleash the tremendous potentials of graphene-based van der Waals (vdW) heterojunctions. Not only are these findings invaluable for designing high-performance graphene-based electronic devices, but also they provide an effective route to realizing dynamic switching either between n-type and p-type Schottky contacts, or between Schottky contacts and Ohmic contacts.     

基于多铁纳磁体的择多逻辑门三维磁化动态特性研究

建立了多铁纳磁体择多逻辑门的三维磁化动态模型,并施加应变时钟(应力或电压)对多铁择多逻辑门的择多计算功能进行了动态仿真,同时分析了应变时钟工作机制以及它与择多逻辑门可靠转换之间的关系.仿真结果表明所建三维动态模型准确地描述了择多逻辑门的工作机制,在30 MPa应力作用下,择多逻辑门接受新输入实现了正确的择多计算功能.研究还发现对中心纳磁体和输出纳磁体依次撤去应变时钟时,提前撤去输出纳磁体上的应力会降低择多逻辑门的正确计算概率,而延迟撤去输出纳磁体上的应力会降低择多逻辑门的工作频率.研究结果深化了人们对多铁择多逻辑门动态特性的认识,可为多铁逻辑电路的设计提供重要指导.     

Investigating the non-classical boundary conditions relevant to strain gradient theories

In the present study, two classes of non-classical constitutive equations consisting of the first and the second order strain gradients theories (FSG and SSG) were applied in order to develop the governing equations of static and free vibrational behavior of beam structures. The governing equations in orders of six and eight were constructed for FSG and SSG theories, respectively. Therefore, higher order or in other words non-classical boundary conditions (HOBCs or NCBCs) came into play in addition to the classical ones (CBCs). Some explanations were presented about the concept of the non-classical boundary conditions. Analytical and finite element (FE) approaches were employed to solve the governing equations. The analytical solutions were utilized in validation and convergence study of FE results. Comparisons were made with the relevant data reported in the open literature; however, to the best of the authors’ knowledge, few references have been published on SSG theory and HOBCs. In the numerical studies, the effects of applying different combinations of CBCs and HOBCs to the static and free vibration behaviors of the beam were investigated. Moreover, the impacts of non-classical elastic constants and the beam size on its behavior were also studied.