氧化物隔离对Si基片上生长L1_0相FePt薄膜磁性的影响

用MgO和SiO_2两种氧化物将FePt薄膜与Si(100)基片隔离,分析隔离层在FePt层发生A1→L1_0转变过程中的作用,寻找用Si母材涂敷L1_0-FePt磁性层来提高磁力显微镜针尖矫顽力的合理方案.采用磁控溅射法在400?C沉积Fe Pt薄膜,在不同温度进行2 h的真空热处理,分析晶体结构和磁性的变化.结果表明:没有隔离层,Si基片表层容易发生扩散,50 nm厚FePt薄膜的矫顽力最大只有5kOe(1 Oe=10~3/(4π)A·m~(-1));而插入隔离层,矫顽力可以超过10 kOe;MgO在Si基片上容易碎裂,热处理温度不能高于600?C,用作隔离层,FePt的最大矫顽力为12.4 kOe;SiO_2与Si基片的晶格匹配更好,热膨胀系数差较小,能承受的最高热处理温度可以超过800?C,使得Fe Pt的矫顽力可以在5 kOe到15 kOe范围内调控,更适合用于制作矫顽力高并可控的磁力显微镜针尖.     

Magnetic hysteresis in rapidly quenched rare-earth alloys

The magnetic and structural properties of rapidly quenched (Pr₈₀Ga₂₀)_100-xFe_x, RTbFe and RTbFe(Co)M alloys are examined over a wide range of chemical compositions, where R ≡ Pr, Sm, MM and M ≡ B and Si. The Ga-containing samples show relatively high coercive fields (up to 3 kOe) in the amorphous state which subsequently disappear after crystallization. On the other hand, the high coercive fields (≈5 kOe) of melt-spun RTbFe samples decrease slightly after crystallization but their magnetic moment increases substantially. Melt-spun RTbFe(Co)M samples are generally magnetically soft in the as-quenched state. Magnetic hardening is produced by annealing the samples around 750°C leading to coercive fields which could not be measured with an ordinary electromagnet (H_c #62; 23 kOe). The best properties have been obtained on a Pr₁₄Fe₇₁B₁₅ sample with a coercive field of 8 kOe and an energy product of 8.5 MGOe. Thermomagnetic data show that a structural transformation takes place upon heating the samples to 750°C. The Curie temperature of the precipitate phase is around 320°C while that of the as-quenched phase is around 160°C. Transmission electron microscope studies show a very fine precipitate structure with a precipitate size below 100 Å. The precipitate phase is believed to be highly anisotropic leading to the observed hard magnetic properties.     

L1_0-FePt合金单层磁性薄膜的微磁学模拟

具有四方结构的L10-FePt合金因其具有高磁晶各向异性和良好的化学稳定性而成为超高密度薄膜磁记录介质的最佳选择.对实验制备得到的磁性能良好的垂直取向L10-FePt合金单层膜进行了微磁学分析.在传统微磁学模型的基础上,根据晶体的对称性,引入了四角磁晶各向异性能密度的唯象表达形式;又依据薄膜生长过程中晶格对称性的破坏,考虑了薄膜面内的应力,并引入了磁弹性能.以四角磁晶各向异性能和磁弹性能为重点,对L10-FePt合金单层膜的磁滞回线进行了详细的分析,并且用微磁学方法确定了薄膜面内应力的大小.     

ZnSb掺杂的Ge2Sb2Te5薄膜的相变性能研究

本文采用双靶(ZnSb靶和Ge₂Sb₂Te₅靶)共溅射制备了系列ZnSb掺杂的Ge₂Sb₂Te₅(GST)薄膜. 利用X射线衍射、透射电子显微镜、原位等温/变温电阻测量、X射线光电子能谱等测试研究了薄膜样品的非晶形态、电学及原子成键特性. 利用等温原位电阻测试表明ZnSb掺杂的Ge₂Sb₂Te₅薄膜具有更高的结晶温度. 采用Arrhenius 公式计算发现ZnSb掺杂的Ge₂Sb₂Te₅薄膜的十年数据保持温度均高于传统的Ge₂Sb₂Te₅薄膜的88.9℃. 薄膜在200, 250, 300和350℃ 下退火后的X射线衍射图谱表明ZnSb的掺杂抑制了Ge₂Sb₂Te₅薄膜从fcc态到hex态的转变. 通过对薄膜的光电子能谱和透射电镜分析可知Zn, Sb, Te原子之间键进行重组, 形成Zn–Sb 和Zn–Te 键, 且构成非晶物质存在于晶体周围. 采用相变静态检测仪测试样品的相变行为发现ZnSb掺杂的Ge₂Sb₂Te₅薄膜具有更快的结晶速度. 特别是(ZnSb)_24.3(Ge₂Sb₂Te₅)_75.7薄膜, 其结晶温度达到250℃, 十年数据保持温度达到130.1℃, 并且在70 mW激光脉冲功率下晶化时间仅～64 ns, 远快于传统Ge₂Sb₂Te₅薄膜的晶化时间～280 ns. 以上结果表明(ZnSb)_24.3(Ge₂Sb₂Te₅)_75.7薄膜是一种热稳定性好且结晶速度快的相变存储材料.     

Microstructures and magnetic properties of Fe---Pt permanent magnets

We have investigated the magnetic properties of Fe---38.5Pt, Fe---39.5Pt and Fe---50.0Pt (at%) alloys after various heat treatment conditions using a vibrating sample magnetometer, and correlated these properties with the microstructures of the alloys by transmission electron microscopy. The Fe---50Pt alloy shows poor magnetic hardness regardless of the heat treatment conditions. The magnetic hardness of the Fe---39.5Pt alloy shows a maximum value after annealing for 10 h at 873 K, while it monotonically decreases after annealing at 1073 K. The alloy with the highest coercivity was composed of a single phase γ₁ with an average domain size of approximately 10 nm. The electron diffraction results indicate that the alloy is frustrated with accumulated stress, induced by a cubic → tetragonal transformation which occurs without twinning. On the other hand, when stress is relieved by twin formation after prolonged aging, the coercivity decreases. By annealing at 1073 K, the well known polytwin structure evolves. However, only poor hard magnetic properties are observed when this polytwin structure appears. Hence, the highest coercivity is attributed to the formation of nanoscale L1₀ ordered antiphase domains which is expected to be a highly anisotropic single domain magnetic particle.     

非晶Ni-P合金的晶化相

利用电镜双倾台倾转Ni₁₂P₅晶体以及对Vafaei-Makhsoos发表的数据的分析,证实了由他所提出的三个新的Ni₃P相并不存在。从而澄清了非晶Ni-P合金在加热过程中总共有七个晶化相析出:α=5.48?的面心立方亚稳相α,由此相转变生成的六角多型体α₁,α₂,α₃亚稳相,体心四方Ni₁₂P₅相,体心四方Ni₃P相及Ni固溶体。 关键词：     

Abnormal variation of magnetic properties with Ce content in(PrNdCe)_2Fe_(14)B sintered magnets prepared by dual alloy method

Resource-saving(PrNdCe)_2Fe_(14)B sintered magnets with nominal composition(PrNd)_(15-x)Ce_xFe_(77)B_8(x=0–10)were prepared using a dual alloy method by mixing(PrNd)_5Ce_(10)Fe_(77)B_8 with(PrNd)_(15)Fe_(77)B_8 powders. For Ce atomic percent of 1% and 2%, coercivity decreases dramatically. With further increase of Ce atomic percent, the coercivity increases, peaks at 6.38 kOe in(PrNd)_(11)Ce_4Fe_(77)B_8, and then declines gradually. The abnormal dependence of coercivity is likely related to the inhomogeneity of rare earth chemical composition in the intergranular phase, where Pr Nd concentration is strongly dependent on the additive amount of(PrNd)_5Ce_(10)Fe_(77)B_8 powders. In addition, for Ce atomic percent of 8%,7%, and 6% the coercivity is higher than that of magnets prepared by the conventional method, which shows the advantage of the dual alloy method in preparing high abundant rare earth magnets.     

MAGNETIC PROPERTIES AND CRYSTALLIZATION OF THE RAPIDLY QUENCHED (Fe1-xNdx) 81.5B18.5 ALLOYS

Magnetic properties and crystallization behaviors of amorphous (Fe_1-xNd_x) _81.5B_18.5 alloys were studied. The crystallization temperature is found to rise at first and then drop monotonically with x, having a maximum value of 976K at x=0.11 (9at% Nd). The (Fe_1-xNd_x) _81.5B_18.5 alloys prepared at a quenching rate of v_s = 6.6m /s are amorphous, and exhibit good glass formability. Both the coercive field H_c and energy product (BH)_max depend strongly on Nd concentration. Amorphous (Fe_1-xNd_x) _81.5B_18.5 alloys with higher Nd concentration have a high coercive field at low temperature, due to the large random uniaxial anisotropy of Nd. The room-temperature H_c and (BH)_max obtained on optimal annealing con-ditions show two maxima as a function of Nd concentration x. The highest room-temperature coercive field H_c =22 kOe within the Nd concentrations around x=0.368 and the maximum energy product(RH)_max= 13.3 MG·Oe at x =0.055 are observed. The hard magnetic properties of these crystallized samples are related to the presence of the bard magnetic Nd₂Fe₁₄B phase.     

Low temperature magnetic and magnetostrictive properties in Pr(Fe_(1-x)Co_x)_(1.9) cubic Laves alloys

The structures,spin reorientations,magnetic,and magnetostrictive properties of the polycrystalline Pr(Fe_(1-x)Co_x)_(1.9)(x=0–1.0)cubic laves phase alloys between 5 K and 300 K are investigated.Large low-field magnetostrictions are observed at 5 K in the alloys with x=0.2 and 0.4 due to the low magnetic anisotropies of these two alloys.A large negative magnetostriction of about-1130 ppm is found in PrCo_(1.9) alloy at 5 K.The magnetizations of the alloys with 0≤x≤0.6decrease abnormally at the spin reorientation temperature T_(sr),and an abnormity is detected in the alloy with x=1.0 at its Curie temperature T_c(45 K).The substitution of Fe by Co increases the value of T_(sr) in the alloy with x value increasing from 0.0 to 0.4,and then reduces the value of Tsr with x value further increasing to 0.6.     

Improvement in coercivity,thermal stability,and corrosion resistance of sintered Nd-Fe-B magnets with Dy_(80)Ga_(20) intergranular addition

To investigate the coercivity,corrosion resistance,and thermal stability of Nd-Fe-B magnets,their properties were investigated at room and high temperature before and after doping with Dy_(80)Ga_(20)(at.%) powder.The coercivity of the magnets increased from the undoped value of 12.72 kOe to a doped value of 21.44 kOe.A micro-structural analysis indicates that a well-developed core-shell structure forms in the magnets doped with Dy_(80)Ga_(20) powder.The improvement in magnetic properties is believed to be related to the refined and uniform matrix grains,continuous grain boundaries,and a hardened(Nd,Dy)_2Fe_(14)B shell surrounding the matrix grains.Additionally,the doped magnets exhibit an obvious improvement in thermal stability.For the magnets with added Dy_(80)Ga_(20) powder,the temperature coefficients of remanence(α) and coercivity(β) increased to-0.106%℃~(-1) and-0.60%℃~(-1) over the range 20-100 ℃,compared to temperature coefficients of-0.117%℃~(-1)(α) and-0.74%℃~(-1)(β) in the regular magnets without Dy_(80)Ga_(20) powder.The irreversible loss of magnetic flux(Hirr) was investigated at different temperatures.After being exposed to 150 ℃ for 2 h,the Hirr of magnets with 4 wt.%Dy_(80)Ga_(20) decreased by ~95%compared to that of the undoped magnets.The enhanced temperature coefficients and Hirr indicate improved thermal stability in the doped Nd-Fe-B magnets.The intergranular addition of Dy_(80)Ga_(20) also improved the corrosion resistance of the magnets because of the enhanced intergranular phase.In a corrosive atmosphere for 96 h,the mass loss of the sintered magnets with 4 wt.%Dy_(80)Ga_(20) was 2.68 mg/cm~2,less than 10%of that suffered by the undoped magnets(28.1 mg/cm~2).     

Amorphous-crystalline dual-layer structures resulting from metastable liquid phase separation in(Fe₅₀Co₂₅B₁₅Si₁₀)₈₀Cu₂₀ melt-spun ribbons

(Fe50Co25B15Si10)80Cu20 ribbons are prepared by using the single-roller melt-spinning method.A dual-layer structure consisting of a(Fe,Co)-rich amorphous phase and a Cu-rich crystalline phase forms due to metastable liquid phase separation before solidification.The magnetic hysteresis loops of the as-quenched and annealed samples are measured at room temperature.It is indicated that the coercivity of the ribbon is almost zero in the as-quenched state.The crystallization leads to the increase of coercivity and decrease of saturation magnetization.     

Growth behavior of high k LaAlO3 films on Si by metalorganic chemical vapor deposition for alternative gate dielectric application

LaAlO₃ (LAO) is explored in this work to replace SiO₂ as the gate dielectric material in metal–oxide–semiconductor field effect transistor. Amorphous LAO gate dielectric films were deposited on Si (0 0 1) substrates by low pressure metalorganic chemical vapor deposition using La(dpm)₃ and Al(acac)₃ sources. The effect of processing parameters such as deposition temperature and precursor vapor flux on growth, structure, morphology, and composition of LAO films has been investigated by various analytical methods deeply. The film growth mechanism on Si is reaction limiting instead of mass transport control. The reaction is thermally activated with activation energy of 37 kJ/mol. In the initial growth stage, Al element is deficient due to higher nucleation barrier on Si. The LAO films show a smooth surface and good thermal stability and remain amorphous up to a high temperature of 850 °C. The electrical properties of amorphous LAO ultrathin films on Si have also been evaluated, indicating LAO is suitable for high k gate dielectric applications.     

A comparison of FePt thin films with HfO2 or MnO additive

The influence of oxide additives on the magnetic and structural properties of FePt L1₀ thin films has been studied. FePt films with HfO₂ additive grown on a 5 nm MgO buffer showed a primarily random texture for both as-deposited and annealed samples. The average grain size was limited to 10 nm and the perpendicular coercivity was 1.3 kOe for a 10 nm thick FePt +20% HfO₂ film annealed at 650°C for 10 min. In direct contrast, MnO additive neither limited grain size nor L1₀ ordering in annealed FePt films. A 10 nm thick FePt+20% MnO film grown on a 5 nm MgO buffer showed a unique discontinuous microstructure composed of clusters of (0 0 1) textured L1₀ grains after being annealed at 650°C for 10 min. The average size of the grains making up these clusters was 50 nm and the perpendicular coercivity of the film exceeded 7 kOe.     

非晶Nd3Fe81B16合金的晶化及其对磁性和M?ssbauer谱的影响

本文报道利用单辊方法制备的非晶Nd₃Fe₈₁B₁₆合金的晶化及其对磁性和M?ssbauer谱的影响。发现在非晶Fe₈₁B₁₉合金中用3at％Nd取代B,使非晶Fe₈₁B₁₉合金的晶化温度提高88℃。在适当的退火条件下晶化后样品在室温下的磁性是:σ_s=189emu/g,σ_r/σ_s=0.7,_iH_c=2.15kOe,B_r≈12kG,_bH_c=2kOe,(BH)_max≈8MGOe。与目前广泛使用的六角铁氧体相比,_bH_c相近,但B_r和(BH)_max远比六角铁氧体高。这种材料仅含有少量的Nd,因此可能开发为一种新的廉价永磁材料。本文对少量Nd的添加对非晶FeB合金的晶化温度,磁性和M?ssbauer谱的影响进行了讨论。初步探讨了高矫顽力的来源,认为它的磁化和反磁化过程可以用畴壁钉扎理论解释。 关键词：     

原子间相互作用势对中Al浓度Ni75AlxV25-x合金沉淀序列的影响

基于微观相场模型与反演算法,研究了中Al浓度及温度对Ni₇₅Al_xV_25-x合金沉淀过程的影响：在相同浓度下,L1₂与DO₂₂结构的第一近邻原子间相互作用势随温度升高呈线性增加,两者呈正比的关系;但在同一温度下,L1₂（DO₂₂）结构的第一近邻原子间相互作用势随Al原子浓度的增加而增加（减少）.同时将反演得出的原子作用势代入微观相场模拟中,探讨中Al浓度合金沉淀序列与原子作用势的关系,即当L1₂的第一近邻原子间相互作用势大于（小于）DO₂₂时,L1₂（DO₂₂）优先析出;当L1₂和DO₂₂的第一近邻原子间相互作用势相等时,两者同时析出.特别地,当Al原子的浓度等于0.0589时,发现L1₂和DO₂₂同时析出.利用微观相场法反演原子间相互作用势,为判断中Al浓度合金的沉淀序列增加了可信度.     

Effect of thermal deformation on giant magnetoresistance of flexible spin valves grown on polyvinylidene fluoride membranes

We fabricated flexible spin valves on polyvinylidene fluoride(PVDF) membranes and investigated the influence of thermal deformation of substrates on the giant magnetoresistance(GMR) behaviors. The large magnetostrictive Fe_(81)Ga_(19)(Fe Ga) alloy and the low magnetostrictive Fe_(19)Ni_(81)(Fe Ni) alloy were selected as the free and pinned ferromagnetic layers.In addition, the exchange bias(EB) of the pinned layer was set along the different thermal deformation axes α_(31) or α_(32) of PVDF. The GMR ratio of the reference spin valves grown on Si intrinsically increases with lowering temperature due to an enhancement of spontaneous magnetization. For flexible spin valves, when decreasing temperature, the anisotropic thermal deformation of PVDF produces a uniaxial anisotropy along the α_(32) direction, which changes the distribution of magnetic domains. As a result, the GMR ratio at low temperature for spin valves with EB α_(32)becomes close to that on Si, but for spin valves with EB α_(31)is far away from that on Si. This thermal effect on GMR behaviors is more significant when using magnetostrictive Fe Ga as the free layer.     

三元Co_(79)Zr_(18)Cr_3合金中高矫顽力

通过在Co_(82)Zr_(18)合金中添加过渡族元素Cr的方法,利用快淬工艺,制备出了Co_(82-x)Zr_(18)Cr_x(x=0,2,3,4)快淬合金薄带,利用磁性测量、X光衍射、热磁分析、扫描电子显微镜,对其磁性能、相组成、微结构进行了研究,实验结果表明,在Co_(82)Zr_(18)合金中添加少量的Cr可以使其矫顽力(iHc)显著提高,其中,Co_(79)Zr_(18)Cr_3快淬薄带经600℃退火处理后iHc=6.5 kOe.相分析发现,600℃退火后的Co_(79)Zr_(18)Cr_3快淬薄带由单一Co_(11)Zr_2相组成,Cr原子进入到了Co_(11)Zr_2相的晶格之中替换了原子半径相对较小的Co原子,这导致了Co_(11)Zr_2居里温度(T_C)的降低却使其磁晶各向异性场(Ha)显著提高;另一方面,通过微结构研究发现,未退火的Co_(79)Zr_(18)Cr_3快淬薄带由50—80 nm的等轴晶粒组成,经600℃退火后,其晶粒形态并未发生改变然而晶粒尺寸却增长到400—500nm。     

Properties of a rare earth free L10-FeNi hard magnet developed through annealing of FeNiPC amorphous ribbons

The rare-earth-free hard magnetic L1₀-FeNi phase found in cosmic meteorites demonstrates potential as a next-generation permanent magnet. However, it is very difficult to artificially produce the L1₀-FeNi phase due to the low atomic diffusion coefficients of Fe and Ni near the order-disorder transition temperature (∼320 °C). Therefore, FeNiPC amorphous alloy systems exhibiting crystallization temperature (T_x) near the transition temperature were investigated. The amorphous alloys were annealed at T_x, resulting in high atomic diffusion. The structural and microstructural characterizations of annealed ribbons revealed the formation of L1₀-FeNi phase through observation of the superlattice peak. The magnetic property, such as coercivity (H_c), also indicated the formation of L1₀-FeNi phase, because the maximum H_c value is 641 Oe after the annealing process.     

Cobalt substituted R---Fe(Co)---C alloys

The formation of tetragonal R₂(FeCo)₁₄C phase has been examined in as-cast and melt-spun R₁₄Fe_78−xCo_xC₈ alloys with cobalt substitutions (R = Y, Dy, Nd). The magnetic properties over a temperature range and the microstructure have been studied as a function of cobalt content. The Curie temperature is increased with Co content but the anisotropy K is decreased. High cobalt content leads to the formation of 1:5 phase. High corecivities have been developed in as-cast and melt-spun Dy₁₄Fe_78−xCo_xC₈ alloys with Co content at zero and 32 at %, respectively. As-cast Nd₁₆Fe_78−xCo_xC₈ alloys did not show any permanent magnetic properties although they had the 2:14:1 phase. However, melt-spun and powdered Nd---Fe---Co---C samples showed a coercivity with the highest value corresponding to a melt-spun Nd₁₄Fe₇₈C₈ sample. Microstructure studies showed that the high H_C in ribbons is due to the fine grain size which is in the range of 500–1000 Å.     

垂直磁各向异性L10-Mn1.67Ga超薄膜分子束外延生长与磁性研究

具有超强垂直磁各向异性的L1₀-Mn_xGa薄膜由于其与半导体材料结构及工艺的高度兼容性而受到广泛关注, 其超高垂直磁各向异性能和极低的磁阻尼因子预示着L1₀-Mn_xGa薄膜在高热稳定性自旋电子学器件中将发挥重要作用. 而L1₀-Mn_xGa超薄膜对于降低L1₀-Mn_xGa基垂直磁各向异性隧道结中的磁矩翻转临界电流密度有着重要的意义. 本文采用分子束外延的方法, 在半导体GaAs衬底上成功制备出了一系列不同厚度的L1₀-Mn_1.67Ga薄膜, 厚度范围为1-5 nm. 生长过程中反射式高能电子衍射原位检测以及X射线衍射结果均表明了其良好的单晶相. 磁性测量结果表明, 厚度在1 nm以上的L1₀-Mn_1.67Ga薄膜均可以保持垂直磁各向异性特征, 厚度为5 nm的L1₀-Mn_1.67Ga薄膜的垂直磁各向异性能可达到14.7 Merg/cm³. 这些结果为基于L1₀-Mn_1.67Ga的垂直磁各向异性隧道结在自旋转移扭矩驱动的磁随机存储器等低功耗器件的集成及应用提供了重要的实验支持.