复合结构螺旋超材料对光波前的高效调控

近年来,超材料和超表面因为一些不同于传统材料的新奇性质一直被广泛研究,而基于超材料或者是超表面的波前控制也是其中的一个热门研究领域.迄今为止,已经提出了很多不同的结构来对反射光和透射光的波前进行调控,在已知的结构中,反射光的波前调控效率已经可以达到较高数值,但是很少有报道能够使用超材料简单高效地调制透射光的波前.本文提出了一种由相同几何结构的左旋和右旋结构复合而成的螺旋超材料.通过使用时域有限差分方法进行仿真,发现这种螺旋结构将会在入射光和透射光之间引入一个可控的相位变化,从而可直接对透射光波前进行调控.仿真结果还表明,该复合结构螺旋超材料在较宽的波长范围内可以达到近64%的透射率.最后通过将该螺旋材料沿着X轴排布成有着连续相位变化的阵列,可以在近红外区域(1.0—1.4μm)观察到反常折射现象,仿真结果与理论计算得出的反常折射角十分符合.     

超材料型周期管路声传播特性及低频宽带控制

船舶管路系统噪声的低频宽带控制是船舶设计和制造中亟待解决的关键问题之一。将超材料理论引入船舶管路系统的结构设计,构造了具有低频声波带隙的一维周期管路结构,并给出了周期管路声波带隙和声波透射系数的计算方法。计算结果表明,该周期管路同时存在声波布拉格带隙和局域共振带隙。在这两种带隙频率范围内,声波在系统中的传播将被衰减抑制。进一步发现,布拉格和局域共振带隙在一定条件会发生耦合,出现带隙耦合展宽现象,且两种带隙存在精确耦合条件。利用带隙耦合的展宽效应和低频设计,可实现声波在低频范围内的传播操控,从而达到船舶管路系统低频噪声宽带控制的目的。     

快速响应的硅基纯相位液晶器件对动态大气湍流波前的校正能力研究

液晶相位调制器的响应时间延迟是影响液晶自适应光学系统性能的一个主要因素, 为了提高系统的响应速度, 开发了一种快速响应的向列相液晶材料, 并制成了反射式硅基液晶器件(LCOS). 分析了该LCOS的相位调制特性及其对静态畸变波前和扰动波前的校正能力. 首先, 测量了LCOS的电光响应特性, 得出其780 nm相位调制量的响应时间为2 ms. 其次, 测量了LCOS的相位调制特性, 并对相位调制进行了线性化处理. 再次, 测量了用该LCOS搭建的液晶自适应光学系统的闭环和开环3 dB带宽, 它们分别为16和18 Hz. 最后, 给出了开环液晶自适应光学系统校正大气湍流的数值模拟结果, 结果表明. 系统的Strehl比由校正前的0.025上升到了校正后的0.225. 因此, 该液晶自适应光学系统可以对Greenwood频率为30 Hz以下的大气湍流进行较良好的校正.     

The design and manufacture of a notch structure for a planar InP Gunn diode

A planar InP-based Gunn diode with a notch doping structure is designed and fabricated for integration into millimeter-wave and terahertz integrated circuits.We design two kinds of InP-based Gunn diodes.One has a fixed diameter of cathode area,but has variable spacing between anode and cathode;the other has fixed spacing,but a varying diameter.The threshold voltage and saturated current exhibit their strong dependences on the spacing(10 μm-20 μm) and diameter(40 μm-60 μm) of the InP Gunn diode.The threshold voltage is approximately 4.5 V and the saturated current is in a range of 293 mA-397 mA.In this work,the diameter of the diode and the space between anode and cathode are optimized.The devices are fabricated using a wet etching technique and show excellent performances.The results strongly suggest that low-cost and reliable InP planar Gunn diodes can be used as single chip terahertz sources.     

Tailoring light with a digital micromirror device

A digital micromirror device (DMD) is a product of micromechanics. The DMD employs numerous micromirrors as the actuating components to switch small portions of light on and off. During the past few decades, such devices have been widely applied in digital light processing technology. The expanding range of applications makes the DMD increasingly important in various research aspects. Recent advances demonstrate that the DMD is potentially better than the traditional liquid crystal spatial light modulator in speed, spectrum sensitivity, and polarization modulation. These characteristics have been verified in a series of recently reported experiments. This review summarizes the related theory, experimental techniques, and applications for wavefront shaping with DMDs in both statically shaping various spatial modes and dynamically compensating for wavefront distortion caused by the scattering medium.

     

Measurement of moments for centroid estimation in Shack-Hartmann wavefront sensor—a wavelet-based approach and comparison with other methods

A wavelet-based method of moment calculation with a set of basis functions is presented for centroid estimation in a Shack-Hartmann Wavefront Sensor. The method has been compared with other algorithms such as statistical averaging, FFT and least-squares method. A comparative analysis shows that wavelet method has a high accuracy and processing speed, and better suited for wavefront reconstruction applications. Further, the wavelet method presented here has a variable accuracy and resolution, and can be optimized for a particular application under consideration.     

Probability distribution of normalized structure factor magnitudes for a centrosymmetric crystal with planar molecules in the unit cell

The reasons and conditions for applicability of the Cauchy distribution law for crystal structure factor components are discussed. It is shown that the standardized structure factors of centrosymmetric crystals are quite prone to be Cauchy distributed for crystals having planar molecules in their unit cells.     

Development of a hand-held sensor probe for detection of sound components radiated from a specific device using surface intensity measurements

In this paper, a hand-held sensor probe is developed for surface intensity measurements. The sensor probe is composed of a 1/2-in. condenser microphone and a lightweight accelerometer of 1 g (=10⁻³ kg) which are connected with a vibration damper made of silicon rubber. The reliable measurement range of the sensor probe is examined and shown to be 100 Hz to7 kHz for sound and vibration. The precision of intensity measurements is confirmed by experiments in noisy environment. The precision is shown to be less than 3 dB for a random noise environment when the S/N is greater than −10 dB and for pure tone environment when the S/N is greater than −5 dB. The sensor probe is applied to determine the sound power level of a hard disc drive unit of a personal computer in an office setting. Good agreement is obtained for A-weighted sound power levels determined by the ISO method.     

Hybrid device for acoustic noise reduction and energy harvesting based on a silicon micro-perforated panel structure

A kind of hybrid device for acoustic noise reduction and vibration energy harvesting based on the silicon micro- perforated panel （MPP） resonant structure is investigated in the article. The critical parts of the device include MPP and energy harvesting membranes. They are all fabricated by means of silicon micro-electro-mechanical systems （MEMS） tech- nology. The silicon MPP has dense and accurate micro-holes. This noise reduction structure has the advantages of wide band and higher absorption coefficients. The vibration energy harvesting part is formed by square piezoelectric membranes arranged in rows. ZnO material is used as it has a good compatibility with the fabrication process. The MPP, piezo- electric membranes, and metal bracket are assembled into a hybrid device with multifunctions. The device exhibits good performances of acoustic noise absorption and acoustic-electric conversion. Its maximum open circuit voltage achieves 69.41 mV.     

Direct write of optical diffractive elements and planar waveguides with a digital micromirror device based UV photoplotter

A photoplotter, based on a digital micromirror device as real-time reconfigurable mask, is designed to direct-write microstructures in different photosensitive materials. Binary and multilevel elements, such as computer generated holograms with 2, 4 and 8 phase levels and planar optical waveguide structures with tapers and/or long period gratings, are fabricated in a single processing step. Direct parallel write into different photosensitive materials with attractive optical properties is proposed and first results are shown in a commercially available organic-inorganic hybrid material.     

基于LED光源的非相干宽带腔增强吸收光谱技术探测HONO和NO2

介绍了基于近紫外发光二极管LED (中心波长约372 nm,半高宽13 nm) 光源的非相干宽带腔增强吸收光谱技术,同时用于探测痕量气体HONO和NO₂. LED出射光经准直后耦合进入长度为70 cm,由两块高反射率镜片组成的高精密光学腔内. 分别测量了氮气消光谱和氦气消光谱,通过两者瑞利散射截面的差异而引起光谱强度的变化来标定镜片反射率.在360—390 nm反演波段内,镜片反射率在390 nm处最大且为0.99962, 对应测量NO₂/HONO混合物时的最大光程约1.71 km,并利用最小二乘拟合反演出了 HONO和NO₂的浓度值.当光谱采集时间为1000 s时, HONO和NO₂的探测灵敏度(1σ) 分别为0.6 ppbv和1.9 ppbv.实验结果表明,该技术为实现大气痕量气体的高灵敏度在线监测提供了另一种可能的途径.