A diode laser spectrometer at 634nm and absolute frequency measurements using optical frequency comb

This paper reports that two identical external-cavity-diode-laser (ECDL) based spectrometers are constructed at 634 nm referencing on the hyperfine B-X transition R(80)8-4 of ¹²⁷I₂. The lasers are stabilized on the Doppler-free absorption signals using the third-harmonic detection technique. The instability of the stabilized laser is measured to be 2.8×10^-12 (after 1000 s) by counting the beat note between the two lasers. The absolute optical frequency of the transition is, for the first time, determined to be 472851936189.5 kHz by using an optical frequency comb referenced on the microwave caesium atomic clock. The uncertainty of the measurement is less than 4.9 kHz.     

光梳主动滤波放大实现锶原子光钟二级冷却光源

提出一种结合注入锁定技术的主动滤波放大方法,将光梳直接注入锁定至光栅外腔半导体激光器,产生窄线宽激光光源,该光源可以用于锶原子光钟二级冷却.实验中,将中心波长为689 nm,带宽为10 nm的光梳种子光源注入689 nm光栅式外腔半导体激光器,通过半导体增益光谱与半导体光栅外腔,从飞秒光梳的多个纵模梳齿中挑选出一个纵模模式来进行增益放大,再通过模式竞争,实现单纵模连续光输出;同时,光梳的重复频率锁定在线宽为赫兹量级的698 nm超稳激光光源上,因此,注入锁定后输出的窄线宽激光也继承了超稳激光光源的光谱特性.利用得到的输出功率为12 mW的689 nm窄线宽激光光源实现了88Sr原子光钟的二级冷却过程,最终获得温度为3μK,原子数约为5×10~6的冷原子团.该方法可拓展至原子光钟其他光源的获得,从而实现原子光钟的集成化和小型化.     

飞秒光梳和碘稳频532nm Nd:YAG激光频率的测量

报道了中国计量科学研究院研制的基于掺钛蓝宝石(Ti:Sapphire)锁模飞秒脉冲激光器的飞秒光学频率梳装置，并利用此装置测量了碘稳频532nm(¹²⁷I₂R(56)32-10) Nd∶YAG固体激光器的频率，结果为 563260223512991±20Hz,相对不确定度为3.6×10^-14.这一数值是直接溯源到铯原子微波频率基准的光学频率测量结果.     

低相噪光学频率梳

光学频率梳是光钟的重要组成部分,相噪是光梳的基本特性。文章从光梳相噪的描述方法入手,对光学频率梳相噪产生的几种常见来源及相噪抑制技术进行了综述,详细介绍了业已实现的几种低相噪光学频率梳。文末展望了未来低相噪光学频率梳的发展新趋势。     

覆盖可见光波长的掺Er光纤飞秒光学频率梳

飞秒光学频率梳波长覆盖范围向可见光波长扩展对于碘稳频激光的绝对频率测量以及光钟研究中钟激光的绝对频率测量都具有十分重要的意义. 本文在自行研制掺Er光纤飞秒光学频率梳的基础上, 采用放大-倍频-扩谱的方案, 实现了激光输出波长向可见光波长的扩展. 掺Er光纤飞秒光学频率梳输出的一部分光激光脉冲, 功率约为8 mW, 首先经掺Er光纤放大器将功率提高到531 mW, 此后利用MgO: PPLN晶体倍频, 倍频后激光的功率为170 mW, 倍频效率为32%, 脉冲宽度为85 fs. 倍频后的激光通过光子晶体光纤进行光谱展宽. 通过优化入射光偏振状态可以实现波长覆盖500-1000 nm, 输出功率为85 mW, 耦合效率为50%. 采用小型化碘稳频532 nm Nd: YAG激光器输出激光与光学频率梳光谱展宽后的激光进行拍频可以获得30 dB的拍频信号. 覆盖可见光波长的掺Er光纤飞秒光学频率梳为可见光范围内激光的绝对频率测量提供了技术手段.     

光纤飞秒光学频率梳的研制及绝对光学频率测量

实验利用商品光纤飞秒激光器,自行构建了一套完整的光学频率梳系统,并获得了约30 dB信噪比的系统频移(f_ceo)信号.实现了光频梳重复频率(f_rep)信号及系统频移(f_ceo)信号的高稳定度锁定,并通过实验验证了光频梳锁定的跟踪精度.基于此稳定光频梳完成了对1064 nm碘稳频Nd:YAG固体激光器的绝对频率测量.实验结果表明,f_rep的跟踪精度在100 s取样时间时优于3.7×10^-14,测量得到的1064 nm激光器绝对频率为:281630111757362 Hz.这一测量结果与国际计量委员会(CIPM)给出的国际推荐值符合到不确定度之内. 关键词： 光纤光频梳 稳频 锁相技术 光学频率计量     

基于飞秒光频梳的双频He-Ne激光器频率测量

利用光纤飞秒光频梳和外腔可调谐半导体激光器, 建立了一套双频He-Ne激光器频率测量系统. 选用铷钟作为系统的频率基准, 通过将外腔半导体激光锁定至光频梳使得其频率溯源至铷钟, 再利用外腔可调谐半导体激光与双频He-Ne激光器输出的正交偏振激光拍频, 同时测量两路正交偏振激光频率. 将可调谐半导体激光器锁定至光频梳第1894449个梳齿, 其绝对频率为473612190000.0±2.7 kHz, 相对不确定度为5.7×10^-12. 对商品双频He-Ne激光器进行频率测量实验, 双频He-Ne激光器水平方向偏振激光频率均值为473612229934 kHz, 竖直方向偏振激光频率均值为473612232111 kHz, 平均时间为1024 s的相对Allan标准差为5.2×10^-11, 频差均值为2.177 MHz, 标准偏差为2 kHz.     

An Yb-fiber frequency comb phase-locked to microwave standard and optical reference

We present a fully stabilized Yb-fiber frequency comb locked to a microwave standard and an optical reference separately. The carrier-envelope offset frequency is generated by a standard f–2f interferometer with 40 dB signal-tonoise ratio. The offset frequency and the repetition rate are stabilized simultaneously to the radio frequency reference for more than 30 hours, and the fractional Allan deviation of the comb is the same as the microwave standard of 10^-12 at 1 s.Alternatively, the comb is locked to an ultra-stable optical reference at 972 nm using an intracavity electro-optic modulator,exhibiting a residual integrated phase noise of 458 mrad(1 Hz–10 MHz) and an in-loop tracking stability of 1.77× 10^-18 at 1 s, which is significantly raised by six orders comparing to the case locked to the microwave frequency standard.     

基于飞秒光学频率梳的大尺寸精密测距综述

飞秒光学频率梳的出现对时间频率技术和光谱学技术产生了深远重大的影响,由此衍生的飞秒光学频率梳绝对测距技术以其快速、大尺寸、高精度等优点已成为国际研究热点,并有望直接应用于大装备制造、激光雷达和卫星编队飞行等大尺寸精密测距。在简要阐述飞秒光学频率梳的原理特性及主要应用的基础上,围绕光梳测距的发展历程及前沿方向,着重介绍了飞秒光梳精密测距近两年来的最新研究进展,并对该技术进行了总结和展望。     

Pump-induced carrier envelope offset frequency dynamics and stabilization of an Yb-doped fiber frequency comb

In this paper, we demonstrate a carrier envelope phase-stabilized Yb-doped fiber frequency comb seeding by a nonlinear-polarization-evolution（NPE） mode-locked laser at a repetition rate of 60 MHz with a pulse duration of 191 fs.The pump-induced carrier envelope offset frequency（ f0） nonlinear tuning is discussed and further explained by the spectrum shift of the laser pulse. Through the environmental noise suppression, the drift of the free-running f0 is reduced down to less than 3 MHz within an hour. By feedback control on the pump power with a self-made phase-lock loop（PLL）electronics the carrier envelope offset frequency is well phase-locked with a frequency jitter of 85 m Hz within an hour.     

All optical arbitrary waveform generation by optical frequency comb based on cascading intensity modulation

We propose and experimentally demonstrate an all optical arbitrary waveform generation by optical frequency comb (OFC) based on cascading intensity modulation. By selecting spectral lines of interest from OFC through optical filters, 10 GHz, 20 GHz, and 60 GHz sinusoidal signals with low phase noise and more complex waveforms, including ultra-short pulse, half-wave cosine, and single frequency modulated MMW signals, are generated easily.     

基于飞秒光频梳的压电陶瓷闭环位移控制系统

利用飞秒光频梳、外腔可调谐半导体激光器和法布里-珀罗干涉仪建立了一套压电陶瓷亚纳米级闭环位移控制系统. 将可调谐半导体激光器锁定至光频梳, 通过精确调谐光频梳的重复频率, 实现了半导体激光器在其工作频率范围内的精密调谐. 利用Pound-Drever-Hall锁定技术将带有压电陶瓷的法布里-珀罗腔锁定至半导体激光器, 进而通过频率发生系统控制压电陶瓷产生亚纳米级分辨率的位移. 实验研究发现锁定至光频梳后可调谐半导体激光器1 s的Allan标准偏差为1.68×10^-12, 将其在30.9496 GHz范围内进行连续闭环调谐, 可获得压电陶瓷的位移行程约为4.8 μm; 以3.75 Hz的步长扫描光频梳的重复频率, 实现了压电陶瓷的450 pm闭环位移分辨率并测定了压电陶瓷的磁滞特性曲线. 该系统不存在非线性测量误差, 且激光频率及压电陶瓷位移均溯源至铷钟频率源. 关键词： 光频梳 压电陶瓷 法布里-珀罗腔 可调谐半导体激光器     

Precise determination of characteristic laser frequencies by an Er-doped fiber optical frequency comb

Femtosecond optical frequency combs correlate the microwave and optical frequencies accurately and coherently. Therefore, any optical frequency in visible to near-infrared region can be directly traced to a microwave frequency. As a result, the length unit "meter" is directly related to the time unit "second". This paper validates the capability of the national wavelength standards based on a home-made Er-doped fiber femtosecond optical frequency comb to measure the laser frequencies ranging from visible to near-infrared region. Optical frequency conversion in the femtosecond optical frequency comb is achieved by combining spectral broadening in a highly nonlinear fiber with a single-point frequency-doubling scheme. The signal-to-noise ratio of the beat notes between the femtosecond optical frequency comb and the lasers at 633, 698, 729, 780, 1064, and 1542 nm is better than 30 dB. The frequency instability of the above lasers is evaluated by using a hydrogen clock signal with a instability of better than 1×10^-13 at 1-s averaging time. The measurement is further validated by measuring the absolute optical frequency of an iodine-stabilized 532-nm laser and an acetylene-stabilized 1542-nm laser. The results are within the uncertainty range of the international recommended values. Our results demonstrate the accurate optical frequency measurement of lasers at different frequencies using the femtosecond optical frequency comb, which is not only important for the precise and accurate traceability and calibration of the laser frequencies, but also provides technical support for establishing the national wavelength standards based on the femtosecond optical frequency comb.     

A proposal for the generation of optical frequency comb in temperature insensitive microcavity

We numerically simulate the generation of an optical frequency comb(OFC) in a microring based on the traditional Si_3N_4 strip waveguide and a temperature compensated slot waveguide.The results show that OFCs are susceptible to temperature with strip waveguide while they can keep stable when temperature changes 10 Kin either low-Q(10~5) or highQ(10~6) microcavity with the well-designed slot waveguide,which has great superiority in practical applications where the temperature drift of the cavity due to the intense pump or surrounding change is unavoidable.     

一种光学频率梳绝对测距的新方法

采用光学频率梳的高精度绝对距离测量技术在航空航天、科学研究和工业生产等领域都发挥着重要作用.提出一种利用光学频率梳技术,通过检测光强实现绝对距离测量的新方法,研究了光学频率梳发出脉冲的时间相干性,分析了光强与被测距离之间的关系、干涉条纹峰值点位置与被测距离之间的关系.建立了基于Michelson干涉原理的测距系统,通过测量光强信息得到被测距离.以高精度纳米位移平台的位移量作为长度基准进行了绝对测距实验,在每个被测距离点都重复进行了10次实验,将10次实验测得的光强值取平均后用于距离的计算.实验结果表明,该方法可以实现绝对距离测量,在10μm测量范围内,最大误差为47 nm.因此,该方法可以应用于大尺寸高精度的绝对距离测量.     

利用光频梳提高台阶高度测量准确度的方法

提出一种利用光频梳和可调谐半导体激光器提高台阶高度测量准确度的方法. 通过将可调谐激光器锁定至光频梳,可对激光器的输出波长进行精确锁定与测量.基于可调合成波长链原理,利用锁定后的半导体激光器构建了一套台阶高度测量方案,该方案可消除合成波长误差对台阶高度测量不确定度的影响. 采用一台可调谐半导体激光器和光频梳进行了5000 s的连续锁定实验, 结果表明,锁定后的可调谐半导体激光器的频率稳定度达 1.8×10^-12.该方法的理论测量不确定度约为7.9 nm, 且测量结果可溯源至时间频率基准.     

2005年诺贝尔物理学奖与光学频率梳

光学频率梳是2005年诺贝尔物理学奖的重要内容，本文结合时间频率标准的发展历史，简要介绍了飞秒频率梳的基本原理、发明背景、科学意义及研究趋势．最后通过对该项发明的思考，浅谈了一点对科学研究方法的不成熟认识．     

高速OCDM系统中的全光阈值技术分析

分析了高速OCDM系统中基于非线性光学环境(NOLM)和非线性放大(NALM)环境的全光阈值技术。考虑了NOLM环境输入脉冲峰值功率对其阈值判决功能的影响,数值模拟了由高非线性光纤构成的NOLM和NALM环境的脉冲整形和旁瓣抑制功能,并和实验结果进行了比较。结果表明基于NOLM和NALM环境的全光阈值技术都能有效地抑制40 Gbit/s的OCDM系统中的干扰噪声,最优的NOLM环境的脉冲峰值输入功率为2 W,而NALM环境只需要mW量级的脉冲峰值输入功率即能够更好地抑制干扰噪声。     

2005年诺贝尔物理学奖与光学频率梳

光学频率梳是2005年诺贝尔物理学奖的重要内容,本文结合时间频率标准的发展历史,简要介绍了飞秒频率梳的基本原理、发明背景、科学意义及研究趋势.最后通过对该项发明的思考,浅谈了一点对科学研究方法的不成熟认识.     

长时间精密锁定的掺Er光纤飞秒光学频率梳

自行研制了基于掺Er光纤飞秒激光器的光学频率梳并实现了重复频率 f_r信号和载波包络偏移频率(Carrier-envelope offset, f_o) 信号的精密锁定, 锁定后的 f_r信号和 f_o 信号的频率抖动量的标准偏差分别为0.515 mHz和93.13 mHz.