高能量掺Yb偏振型大模场面积光子晶体光纤孤子锁模飞秒激光器

实验研究了基于掺Yb偏振型大模场面积光子晶体光纤的孤子锁模激光器,获得了高脉冲能量的飞秒激光输出. 激光器基于线形腔结构,利用光栅对补偿腔内色散,并通过半导体可饱和吸收镜实现锁模的自启动. 实验中从振荡级直接获得了平均功率为700mW, 重复频率为47.3MHz(对应于14.8 nJ的单脉冲能量),脉冲宽度为518 fs的稳定锁模脉冲输出. 与普通孤子锁模飞秒光纤激光器相比,输出的单脉冲能量提高了两个数量级. 关键词： 光子晶体光纤 飞秒 光纤激光器 孤子锁模     

Dynamic control of the operation regimes of a mode-locked fiber laser based on intracavity polarizing fibers: experimental and theoretical validation

An intracavity polarizing fiber is proposed to control the emission regime of a passively mode-locked fiber laser. Stable operation in self-starting high and low dispersion soliton mode-locking and 100 GHz multiwavelength regimes is demonstrated through numerical simulations and experimental validation. Mode-locking stability is ensured by a saturable absorber in the ring cavity. The effective selection of operation regime is dynamically carried out by controlling the intracavity polarization state.     

Dissipative dispersion-managed soliton 2 μm thulium/holmium fiber laser

We report a first dissipative dispersive-managed soliton fiber laser operating at 2?μm. The cavity comprised of all-anomalous-dispersion fiber employs chirped fiber Bragg grating, which ensures net-normal cavity dispersion and semiconductor saturable absorber for mode-locking.     

Er-doped all-fiber laser mode-locked by graphitic carbon nitride nanosheets

Few-layer graphitic carbon nitride(g-C_3N_4) nanosheets were fabricated and utilized as a saturable absorber for mode-locking in an Er-doped fiber laser with net normal dispersion. The g-C_3N_4/polyvinyl alcohol(PVA) hybrid-film-based saturable absorber has a modulation depth of 4.01% and a saturation intensity of 7.5 MW/cm~2. By integrating g-C_3N_4-PVA mode-locker into the laser cavity, a mode-locked operation could be obtained. The achieved mode-locking pulse centered at 1530.3 nm has a pulse width of 530 ps. Its repetition rate is 40.8 MHz, and the corresponding signal-to-noise ratio is about 55 dB.     

Zinc-oxide/PDMS-clad tapered fiber saturable absorber for passively mode-locked erbium-doped fiber laser

We propose and demonstrate a passively mode-locked erbium-doped fiber laser(EDFL) based on zincoxide/polydimethylsiloxane(Zn O/PDMS) saturable absorber(SA) that evanescently interacts with the light on a tapered fiber. The Zn O/PDMS composite is coated on the whole surface of the tapered fiber to guarantee the maximum efficiency of the SA device, with a measured insertion loss of 0.87 d B and a modulation depth of 6.4%. The proposed laser can generate soliton mode-locking operation at a threshold power of 33.07 m W. The generated output pulse yields a repetition rate and pulse width of 9.77 MHz and 1.03 ps, respectively. These results indicate that the proposed Zn O/PDMS-clad tapered fiber could be useful as an efficient, compatible, and low-cost SA device for ultrafast laser applications.     

Experimental study of electro-optical Q-switched pulsed Nd:YAG laser

We report the specification of a compact and stable side diode-pumped Q-switched pulsed Nd:YAG laser. We experimentally study and compare the performance of the pulsed Nd:YAG laser in the free-running and Q-switched modes at different pulse repetition rates from 1 Hz to 100 Hz. The laser output energy is stabilized by using a special configuration of the optical resonator. In this laser, an unsymmetrical concave-concave resonator is used and this structure helps the mode volume to be nearly fixed when the pulse repetition rate is increased. According to the experimental results in the Q-switched operation, the laser output energy is nearly constant around 70 mJ with an FWHM pulse width of 7 ns at 100 Hz. The optical-to-optical conversion efficiency in the Q-switched regime is 17.5%.     

Toward higher-order passive harmonic mode-locking of a soliton fiber laser

We report >13 MHz/mW pump power efficiency in increasing the repetition rate of passive harmonic mode-locking by engineering the soliton pulse energy in Er fiber lasers incorporating carbon nanotube saturable absorber. Stable pulses with a ～5 GHz repetition rate and 40 dB of super-mode suppression are demonstrated with only ～400 mW pump power in a single-clad fiber laser.     

氧化石墨烯被动锁模掺镱光纤激光器多脉冲现象的实验研究

利用氧化石墨烯作为可饱和吸收体,在被动锁模全正常色散掺镱光纤激光器中研究了多脉冲的现象,在同一抽运功率不同偏振态下,实验获得了矩形脉冲谐波锁模、耗散孤子谐波锁模、准谐波锁模,脉冲峰值周期性调制,脉冲簇、脉冲束、混沌多重脉冲的多脉冲现象,插入激光腔内的2nm窄带滤波器具有限制增益带宽、对脉冲塑形、诱导多脉冲产生的作用,调节偏振控制器相当于改变腔内增益,是实现不同类型多脉冲现象的主要原因,本实验研究有利于加深对多脉冲动力学行为在正常色散区域氧化石墨烯锁模掺镱光纤激光器中的理解。     

147 fs碳纳米管倏逝场锁模全光纤掺铒光纤激光器

利用化学腐蚀法在光纤包层表面成功制备了调制深度为3.9%的单壁碳纳米管饱和吸收体.组建了环形腔结构的全光纤掺铒光纤激光器,以制备的单壁碳纳米管薄膜为锁模元件,利用倏逝场锁模实现了锁模输出.锁模脉冲的中心波长为1556 nm,3 dB光谱带宽为24 nm,脉冲宽度为147 fs,重复频率为150 MHz.在520mW抽运功率下,平均输出功率为21 mW,相应的单脉冲能量为0.14 nJ.     

Mode-locked fiber laser in the C-band region for dual-wavelength ultrashort pulses emission using a carbon nanotube saturable absorber

A saturable absorber is commonly employed to generate an ultrashort laser with a mode-locking scheme. In an erbium-doped fiber laser system, the laser regimes of either 1530 or 1550 nm wavelength are procured based on the absorption profile of the erbium-doped fiber. The absorption of the erbium-doped fiber is designed to emit at both wavelengths by controlling the net gain of the laser cavity. Subsequently, simultaneous erbium-doped fiber laser emission is attained at 1533.5 and 1555.1 nm with the pulse duration of 910 and 850 fs, respectively.Therefore, this work maximizes the output portfolios of a mode-locking fiber laser for dual-wavelength ultrashort pulses emission.     

Single-walled carbon nanotubes on side polished fiber as a universal saturable absorber for various laser output states

We demonstrated four different laser operational states in the same passive fiber ring laser cavity by controlling solely the polarization state in a saturable absorber. The demonstrated laser operational states were continuous wave, mode-locking, Q-switching, and Q-switched mode-locking. The saturable absorber was fabricated by spin-coating a single-walled carbon nanotubes (SWCNT)/polymer composite on a side polished fiber providing enhanced nonlinear interaction with the SWCNT. The wide tuning range of the saturable absorber allows the simple means to generate different forms of laser output from a single laser cavity.     

基于10 m光子晶体光纤的放大自相似锁模振荡器研究

基于单根10 m大模场面积保偏光子晶体光纤, 搭建了带有色散图的放大自相似振荡器; 通过仔细调节腔内色散量的大小以及位于色散补偿端的端镜前的狭缝位置和大小, 实现了稳定的锁模运转, 获得了抛物线形脉冲输出. 输出脉冲的重复频率为8.6 MHz, 脉冲宽度为6.2 ps, 光谱宽度为3.84 nm, 平均功率820 mW, 对应单脉冲能量95 nJ. 这是第一次在自相似振荡器中直接获得重复频率在10 MHz 以下的脉冲输出, 95 nJ也是目前自相似振荡器直接输出的最高脉冲能量. 通过数值模拟证实了在第一个光栅的零级反射处和狭缝滤波后可以分别实现抛物线型脉冲和高斯脉冲的两种锁模脉冲输出.     

Stable passively Q-switched operation of Tm3+ doped silica fiber laser by anti-resonant Fabry-Perot saturable absorber

We demonstrate a diode-pumped passively Q-switched Tm-doped double-cladding silica fiber laser operating at wavelength of 1960 nm using an anti-resonant Fabry-Perot saturable absorber as passive modulation element. To determine a relatively preferable fiber length for stable cw Q-switched operation, three active fiber simples with the length of 1.1, 5.3, and 7.0 m were employed respectively in our experiments. With 1.1 m gain fiber, we generated Q-switched pulses with a pulse width of 245 ns and an average power of up to 2.2 W at a repetition rate of 620 kHz. For the longer two fiber samples, Q-switched operation with longer pulse duration, Q-switched mode-locking and cw mode-locking were observed, respectively.     

Generation of domain-wall solitons in an anomalous dispersion fiber ring laser

We report experimental observations performed using a net anomalous dispersion Er-doped fiber ring laser without polarization-selective elements, highlighting the domain-wall solitary pulses generated under the incoherent polarization coupling. By adjusting the pump power and the polarization state appropriately, bright and dark solitons can stably co-exist in the cavity, both centered at 1562.16 nm with a 3-dB spectral width of ～ 0.15 nm and a repetition rate of 3.83 MHz. Moreover, the 0.8 mm long thulium-doped fiber (TDF) facilitated the mode-locking and self-starting of the laser. This is the first demonstration of a laser being used to generate bright and dark solitons synchronously while using TDF as the saturable absorber (SA). Except possessing the all-fiber structure, the laser exhibits good stability, which may have a significant influence on improvement of the pulse-laser design, and may broaden practical applications in optical sensing, optical communication, and soliton multiplexed systems.     

Passive mode-locking of an Ar+-laser with rhodamine 6g as saturable absorber and double mode-locking of the pump- and dye laser system

The synchronization of the modes of the Ar⁺-pump laser by using a dye as saturable absorber is proposed. Besides, the passive mode-locking is extended to double mode-locking. In this case the dye simultaneously acts as a synchroneously pumped laser medium.     

Switchable mode-locking states in an all-fiber all-normal-dispersion ytterbium-doped laser

Multi-operation state in an all-normal-dispersion ytterbium-doped fiber laser is obtained by introducing nonlinear polarization or hybrid mode-locking mechanism in the laser cavity. In addition to operating the laser at continuous-wave mode-locking, various operation states including continuous-wave, Q-switched mode-locking, pulse-splitting, and harmonic mode-locking can be achieved by tuning the laser pump power or an intracavity polarization controller. Insertion of a semiconductor saturable absorber mirror in the cavity helps to shorten the output pulsewidth of the hybrid mode-locked laser. When the pump power is rapidly adjusted, a strong asymmetric hysteresis behavior can be observed during the manipulation between different orders of harmonic mode-locking.     

High-power passive mode-locking of a diode pumped Yb:GdVO4 laser

Passive mode-locking of a diode pumped Yb-doped GdVO₄ crystal laser was demonstrated for the first time to our knowledge. The laser was mode-locked at the wavelength of 1019.1 nm and had an average output power of 1.01 W. The mode-locked pulse duration was 3.1 ps. The laser was end-pumped by a high-power fiber pigtailed laser diode bar and the mode-locking was enabled by a semiconductor saturable absorber mirror (SESAM).     

Impact of dispersion on pulse dynamics in chirped-pulse fiber lasers

We report on a systematic study of an environmentally stable mode-locked Yb-doped fiber laser operating in the chirped-pulse regime. The linear cavity chirped-pulse fiber laser is constructed with a saturable absorber mirror as nonlinear mode-locking mechanism and a nonlinearity-free transmission-grating-based stretcher/compressor for dispersion management. Mode-locked operation and pulse dynamics from strong normal to strong anomalous total cavity dispersion in the range of +2.5 to ?1.6 ps² is experimentally studied. Strongly positively chirped pulses from 4.3?ps (0.01?ps²) to 39?ps (2.5?ps²) are obtained at normal net-cavity dispersion. In the anomalous dispersion regime, the laser generates average soliton feature negatively chirped pulses with autocorrelation pulse durations from 0.8?ps (?0.07 ps²) to 3.9?ps (?1.6 ps²). The lowered peak power due to the pulse stretching allows one to increase the double pulse threshold. Based on the numerical simulation, different regimes of mode locking are obtained by varying the intra-cavity dispersion, and the characteristics of average soliton, stretched-pulse, wave-breaking-free and chirped-pulse regimes are discussed.     

Femtosecond Tm-Ho co-doped fiber laser using a bulk-structured Bi_2Se_3 topological insulator

We experimentally demonstrate a femtosecond mode-locked thulium-holmium(Tm-Ho) co-doped fiber laser incorporating a saturable absorber(SA) based on a bulk-structured bismuth selenide(Bi_2Se_3) topological insulator(TI). The SA was prepared by depositing a mechanically exfoliated Bi_2Se_3 TI layer onto a side-polished optical fiber platform. Unlike high-quality nano-structured Bi_2Se_3 TI-based SA, bulk-structured Bi_2Se_3 with non-negligible oxidation was used as a saturable absorption material for this experimental demonstration due to its easy fabrication process. The saturation power and modulation depth of the prepared SA were measured to be ~ 28.6 W and ~13.4%, respectively. By incorporating the prepared SA into a Tm-Ho co-doped fiber ring cavity, stable soliton pulses with a temporal width of ~ 853 fs could be generated at 1912.12 nm. The 3-dB bandwidth of the mode-locked pulse was measured to be ~4.87 nm. This experimental demonstration reaffirms that Bi_2Se_3 is a superb base material for mid-infrared passive mode-locking even under oxidation.     

单偏振控制器环形腔光纤激光器实验研究

理论分析了非线性偏振旋转环形腔作为类饱和可吸收体获得脉冲的物理机理。在光纤环形腔结构中,采用单个偏振控制器实现了非线性偏振旋转锁模,直接获得了脉冲宽度为131 fs的超短脉冲输出。实验中,采用性能稳定的976 nm半导体二极管激光器作为抽运源,使用高掺杂浓度的Er3 光纤为增益介质,通过调节偏振控制器,获得了光谱谱宽(3 dB带宽处)为23.5 nm的稳定锁模脉冲输出。脉冲中心波长为1535.9 nm,平均功率为5.91 mW,脉冲重复率为11.20 MHz。