高效无空穴传输层碳基钙钛矿太阳能电池的制备与性能研究

碳基钙钛矿太阳能电池因稳定性高、成本低廉而备受关注,但由于钙钛矿与碳电极之间能级匹配度不高,界面阻力大而导致效率不及金属基钙钛矿太阳能电池.本文制备了碳基无空穴传输层FTO/c-TiO₂/m-TiO₂/CH₃NH₃PbI₃/Carbon电池结构.通过对介孔二氧化钛层、钙钛矿层厚度进行优化,并对钙钛矿的薄膜形貌及钙钛矿激发电子寿命、可见光吸收度、载流子的提取与分离等进行深度分析,讨论了电池效率提升的内在机理.当介孔氧化钛层和钙钛矿层达到最优厚度时,钙钛矿太阳能电池获得了开路电压（V_oc）为0.93 V、电流密度（J_sc）为21.75 mA/cm²、填充因子为55%、光电转化效率达到11.11%.同时对电池进行了稳定性研究,在室温湿度为40%–50%的条件下放置15 d电池性能依旧稳定保持原来的95%,优于金属基钙钛矿太阳能电池,从而为碳电极钙钛矿太阳能电池的商业化发展提供了可能.     

钙钛矿薄膜气相制备的晶粒尺寸优化及高效光伏转换

钙钛矿薄膜的气相制备是一种极具潜力的工业化生产工艺,但薄膜的质量控制目前远落后于溶液制备法.本文通过建立PbI_2薄膜向钙钛矿薄膜完全转化过程中反应时间、晶粒尺寸与温度的关系,实现了薄膜的质量优化及大面积钙钛矿薄膜的制备,将薄膜的平均晶粒粒径从0.42μm优化到0.81μm.基于空间电荷限制电流模型对缺陷密度的研究显示,钙钛矿薄膜的缺陷密度由5.90×10~(16)cm~(–3)降低到2.66×10~(16)cm~(–3).光伏器件(FTO/TiO_2/C_(60)/MAPbI_3/spiro-OMeTAD/Au结构)测试显示,面积为0.045cm~2器件的平均光电转换效率从14.00%提升到17.42%,最佳光电转换效率达到17.80%,迟滞因子减小至4.04%.同时,基于180℃制备的1cm~2器件的光电转换效率达到13.17%.     

高效钙钛矿-有机本体异质结杂化串联太阳能电池

制备了一种有机铅卤钙钛矿-有机本体异质结杂化串联太阳能电池。采用紫外可见吸收光谱、原子力显微镜对薄膜形貌进行了表征。结果表明:有机本体异质结层可以有效改善钙钛矿的表面形貌, 增强了可见光的吸收。优化后的串联结构电池的短路电流可达19.14mA/cm², 开路电压为0.76V, 光电转换效率达到了6.54%。钙钛矿电池和有机本体异质结电池串联结构可以同时提高短路电流及填充因子, 二者具有较好的相容性和协同作用。     

Nano Ag-enhanced photoelectric conversion efficiency in all-inorganic,hole-transporting-layer-free CsPbIBr2 perovskite solar cells

All-inorganic, hole-transporting-layer-free CsPbIBr₂ perovskite solar cells have great potential for development, but their device performance needs to be further improved. Recently, metal nanostructures have been successfully applied in the field of solar cells to improve their performance. Nano Ag-enhanced power conversion efficiency (PCE) in one CsPbIBr₂ perovskite solar cell utilizing localized surface plasmons of Ag nanoparticles (NPs) on the surface has been researched experimentally and by simulation in this paper. The localized surface plasmon resonance of Ag NPs has a near-field enhancement effect, which is expected to improve the light absorption of CsPbIBr₂ perovskite photovoltaic devices. In addition, Ag NPs have a forward-scattering effect on the incident light, which can also improve the performance of CsPbIBr₂-based perovskite photovoltaic devices. By directly assembling Ag NPs (with a size of about 150 nm) on the surface of fluorine-doped tin oxide it is found when the particle surface coverage is 10%, the CsPbIBr₂ perovskite photovoltaic device achieves a best PCE of 2.7%, which is 9.76% higher than that of the control group. Without changing any existing structure in the ready-made solar cell, this facile and efficient method has huge applications. To the best of our knowledge, this paper is the first report on nano Ag-enhanced photoelectric conversion efficiency in this kind of CsPbIBr₂ perovskite solar cell.     

Device simulation of lead-free CH_3NH_3SnI_3 perovskite solar cells with high efficiency

The lead-free perovskite solar cells(PSCs) have drawn a great deal of research interest due to the Pb toxicity of the lead halide perovskite.CH_3NH_3SnI_3 is a viable alternative to CH_3NH_3PbX_3,because it has a narrower band gap of 1.3 eV and a wider visible absorption spectrum than the lead halide perovskite.The progress of fabricating tin iodide PSCs with good stability has stimulated the studies of these CH_3NH_3SnI_3 based cells greatly.In the paper,we study the influences of various parameters on the solar cell performance through theoretical analysis and device simulation.It is found in the simulation that the solar cell performance can be improved to some extent by adjusting the doping concentration of the perovskite absorption layer and the electron affinity of the buffer and HTM,while the reduction of the defect density of the perovskite absorption layer significantly improves the cell performance.By further optimizing the parameters of the doping concentration(1.3 × 10~(16) cm~3) and the defect density(1 × 10~(15) cm~3) of perovskite absorption layer,and the electron affinity of buffer(4.0 eV) and HTM(2.6 eV),we finally obtain some encouraging results of the J_(sc) of 31.59 mA/cm~2,V_(oc) of 0.92 V,FF of 79.99%,and PCE of 23.36%.The results show that the lead-free CH_3NH_3SnI_3 PSC is a potential environmentally friendly solar cell with high efficiency.Improving the Sn~(2+) stability and reducing the defect density of CH_3NH_3SnI_3 are key issues for the future research,which can be solved by improving the fabrication and encapsulation process of the cell.     

基于Al_2O_3/MoO_3复合阳极缓冲层的倒置聚合物太阳能电池的研究

采用旋涂Al_2O_3前驱体溶液和低温退火的方法在活性层上形成Al_2O_3薄膜,并与MoO_3结合形成Al_2O_3/MoO_3复合阳极缓冲层,制备了以聚3-己基噻吩:[6.6]-苯基-C_(61)-丁酸甲酯(P3HT:PC_(61)BM)为活性层的倒置聚合物太阳能电池,并通过改变Al_2O_3前驱体溶液的浓度来分析复合阳极缓冲层对器件性能的影响.结果发现,Al_2O_3/MoO_3复合阳极缓冲层能有效调控倒置聚合物太阳能电池的光电性能及其稳定性.当Al_2O_3前驱体溶液的浓度为0.15%时,器件光伏性能达到最优值,与MoO_3单缓冲层的器件相比,光电转换效率(PCE)由3.85%提高到4.64%;经过80天老化测试后,具有复合阳极缓冲层的器件PCE保留为初始值的76%,而单缓冲层的器件PCE已经下降到50%以下.器件性能得到改善的原因是Al_2O_3/MoO_3复合阳极缓冲层增强了倒置太阳能电池器件阳极对空穴的收集能力,同时钝化了器件活性层,从而提升了太阳能电池器件的光伏性能及其稳定性.     

Ge-Sb-Se硫系玻璃的折射率和热光系数

Ge-Sb-Se硫系玻璃被认为是极佳的红外传输材料和有潜力的非线性光学材料.在光学设计中,玻璃的线性折射率(n)及其热光系数(ζ)是关键技术参数.以预测和调控Ge-Sb-Se玻璃的n和ζ为目的,考察了玻璃的n,ζ,密度(d)和体积膨胀系数(β)与化学参数dSe和拓扑网络结构参数r的内在联系.研究发现,玻璃的n随d的增加而增大;ζ随β的增大而近似线性减小;β随dSe的减小或r的增大而减小;当Ge含量固定时, d随dSe的减小或r的增大而增大,当Sb含量固定时, d在dSe=0时具有最小值.基于实测d和n,拟合获得了Ge, Sb和Se元素在2—12μm波段的摩尔折射度(R_i),分别为R_(Ge)=10.16—10.50 cm~3/mol,RSb=16.71—17.08 cm~3/mol和RSe=11.15—11.21 cm~3/mol,根据d和R_i计算得到的n与实测值的偏差小于1%.基于实测ζ和β,拟合得到了Ge, Sb和Se元素在2—12μm波段的摩尔折射度温度系数(φ_i),分别为φ_(Ge)=21.1—22.6 ppm/K,φ_(Sb)=7.2—8.4 ppm/K和φ_(Se)=90.2—94.2 ppm/K,根据β和φ_i计算得到的ζ与实测值的偏差小于6 ppm/K.     

PTCDI-C8作为阴极修饰层提高钙钛矿太阳能电池的性能

采用N,N'-二正辛烷基-3,4,9,10-苝四甲酰二亚胺（PTCDI-C₈）对钙钛矿电池电子传输层（PCBM）进行界面修饰以减少PCBM与Al电极之间的漏电流,提高阴极的电子收集效率。通过调节PTCDI-C₈薄膜的厚度优化界面接触和电子传输性能。实验结果表明：当PTCDI-C₈薄膜的厚度为20 nm时得到的器件性能最优。光电转换效率（PCE）由5.26%提高到了8.65%,开路电压（V_oc）为0.92 V,短路电流（J_sc）为15.68 mA/cm²,填充因子（FF）为60%。PTCDI-C₈能够有效阻挡空穴向阴极传输,同时PTCDI-C₈具有较高的电子迁移率以及较高的稳定性,在增加电子传输的同时,可减少环境对PCBM的侵蚀,提高了器件的稳定性。     

Simulation design of P–I–N-type all-perovskite solar cells with high efficiency

According to the good charge transporting property of perovskite, we design and simulate a p–i–n-type all-perovskite solar cell by using one-dimensional device simulator. The perovskite charge transporting layers and the perovskite absorber constitute the all-perovskite cell. By modulating the cell parameters, such as layer thickness values, doping concentrations and energy bands of n-, i-, and p-type perovskite layers, the all-perovskite solar cell obtains a high power conversion efficiency of 25.84%. The band matched cell shows appreciably improved performance with widen absorption spectrum and lowered recombination rate, so weobtain a high J_(sc) of 32.47 m A/cm~2. The small series resistance of the all-perovskite solar cell also benefits the high J_(sc). The simulation provides a novel thought of designing perovskite solar cells with simple producing process, low production cost and high efficient structure to solve the energy problem.     

以BAlq为主体的高效高色纯度的红色有机电致磷光器件

以铱配合物红色磷光体Ir(piq)₂(acac)为掺杂剂,制备了基于BAlq材料的红色电致磷光器件,其结构为ITO/NPB(30nm)/Ir(piq)₂(acac):BAlq(25nm)/BCP(13nm)/Alq₃(35nm)/LiF(1nm)/Al(1000nm),当掺杂浓度为8%的时候,器件发光的色坐标为(x=0.67,y=0.32),基本满足了全色显示对红色发光的要求。在电压为16V时,器件达到最高亮度9380cd/m²。在电流密度为5.45mA/cm²时,外量子效率达到最大5.7%。由于磷光体Ir(piq)₂(acac)的磷光寿命较短,所以器件在高电流密度下,仍然保持较高的外量子效率。电流密度为100mA/cm²时,外量子效率仍然维持在4.7%。进一步研究表明在器件中短程的Dexter能量传递以及红光染料对空穴的直接捕获两种机制同时存在。     

The oxidation of fullerene [C70] with various oxidants by ultrasonication

The reaction of C₇₀ by ultrasonication with various oxidants such as 3-chloroperoxy benzoic acid (Fluka 99%), 4-methyl morpholine N-oxide (Aldrich 97%), chromium (VI) oxide (Aldrich 99.9%), and oxone^® monopersulfate compound, at room temperature causes the oxidation of fullerene [C₇₀(O)_n] (n=1–2 or n=1). The FAB-MS, UV–visible, FT-IR spectra, and HPLC analysis confirmed that products of fullerene oxidation are [C₇₀(O)_n] (n=1–2 or n=1).     

Effect of unidirectional solidification rate on Jc for current lead

The dependence of transport J_c value on the traveling rate and the nominal composition was investigated by taking different nominal compositions of YBa₂Cu₃O_6+x (Y123) + n mol% Y₂BaCuO₅ (Y211) (n = 10, 20, 30, 40 and 50) with addition of 0.5 wt% of Pt on samples processed by different unidirectional solidification rates, namely 1, 3 and 5 mm/h. The highest J_c was found in the sample with 30% Y211 addition by the higher traveling rate adjusted to prevent the formation of polycrystals. In this φ 1.56 × 60 mm sample the values of transport I_c and J_c were 1370 A and 71 700 A/cm², respectively, which were obtained by the conventional DC four-probe method with criterion of 1 μV/cm at 77 K and self-field.     

双电子传输层对有机发光二极管效率及其衰减的改善

采用Bphen和BCP制成双电子传输层(Doubleelectrontransportlayers, DETLs)的有机发光二极管器件, 与Bphen单独作ETL的器件相比, DETLs器件具有较小的空穴漏电流, 效率提升10%。与BCP独自作ETL的器件相比, 更多的电子注入使DETLs器件的效率在50~600mA/cm²的电流范围内没有衰减。BCP作ETL的器件的效率从50mA/cm²时的2.5cd/A衰减至300mA/cm²的2.1cd/A, 衰减了16%。Cs₂CO₃:BCP独自作ETL的器件效率在50~300mA/cm²的电流范围内衰减了30%, 而Bphen/Cs₂CO₃:BCP作DETLs的器件效率在50~600mA/cm²的电流范围内衰减幅度为0, 原因是Bphen阻挡了Cs原子扩散至发光层。     

Thermoelectric power and irreversibility field of (Hg,Tl)2Ba2Can−1CunOy (n=2–5) superconductors

We have measured the thermoelectric power, S, and the irreversibility field, H_irr, of the superconducting samples of (Hg,Tl)₂Ba₂Ca_n−1Cu_nO_y (n=2–5). S values for the (Hg,Tl)-22(n−1)n above their T_c's drastically increase with increasing n. Judging from the S values at room temperature, the n=2 and 3 samples are located in the overdoped region, the n=4 is in the almost optimally doped and the n=5 is in the underdoped region. H_irr values for the n=4 and 5 samples are higher than those for the as-synthesized and annealed n=3 samples. It is considered that the enhancement in H_irr is due not only to the increase of hole concentration but to the increase in the number of CuO₂ sheets.     

白色有机发光器件及其稳定性

报道了一种稳定的白色有机薄膜电致发光器件.电流效率6cd/A,在电流密度20mA/cm²驱动下,亮度为1026cd/m²;最高亮度21200cd/m²,色度(x=0.32,y=0.40).该器件具有较平稳的效率电流关系,即具有弱的电流荧光猝灭.初始亮度100cd/m²下,半亮度寿命达22245h.     

W doping-dependent structural and ferroelectric properties of SrBi2Nb2O9 ferroelectric ceramics

The structural and ferroelectric characteristics of SrBi₂(Nb_1−xW_x)₂O₉ (x=0–0.12) ferroelectric ceramics were investigated. SrBi₂(Nb_1−xW_x)₂O₉ ceramics consisted of a single-phase layered perovskite structure when x was less than 0.06. Uniform microstructure and grain size reduction were observed after the introduction of W. The maximum remanent polarization of 16 μC/cm² appeared at x=0.03, and the coercive field decreased with increasing concentration of W. The ferroelectric behavior of SrBi₂(Nb_1−xW_x)₂O₉ ceramics is interpreted based on the Raman measurement.     

Effects of substitution of Ti for Fe in BiFeO3 films prepared by sol–gel process

Ti substituted BiFe_1−xTi_xO_3+δ films have been prepared on indium–tin oxide (ITO)/glass substrates by the sol–gel process. The films with x=0.00–0.20 were prepared at an annealing temperature of 600 °C. X-ray diffraction patterns indicate that all films adopt R3m structure and the films with x=0 and 0.10 show pure perovskite phase. Cross-section scanning shows the thickness of the films is about 300 nm. Through 0.05 Ti substitution, the 2P_r increases to 8.30 μC/cm² from 2.12 μC/cm² of the un-substituted BiFeO₃ film and show enhanced ferroelectricity at room temperature. The 2P_r values are 2.63 and 0.44 μC/cm² for the films with x=0.01 and 0.2, respectively. Moreover, the films with x=0.05 and 0.10 show enhanced dielectric property since the permittivity increases near 150 at the same measuring frequency. Through the substitution of Ti, the leakage conduction is reduced for the films with x=0.05–0.20.     

十二烷二酸修饰TiO_2电子传输层改善钙钛矿太阳电池的电流特性

在经典的平面异质结钙钛矿太阳电池中,TiO_2致密层的电子传输性能一直是获得优异光伏性能的决定性因素之一.相较于spriro-OMe TAD等常见的空穴传输材料优异的空穴传输能力,作为电子传输材料的TiO_2的导电性较弱,无法形成良好的电荷匹配.为了解决这个问题,我们使用自组装的十二烷二酸(DDDA)单分子层来修饰TiO_2致密层的表面,TiO_2致密层的导电性能得到大幅提升,并且其能带结构得到优化,促进了电子传输,降低了电子积聚和载流子复合,使得电池的短路电流密度(JSC)从修饰前的20.34 mA·cm~(-2)提升至修饰后的23.28 mA·cm~(-2),进而使得电池在标准测量条件下的光电能量转换效率从14.17%提升至15.92%.同时还发现,通过DDDA修饰TiO_2致密层,所制备的器件的光稳定性显著提升,器件未封装暴露在AM 1.5光强100 mW·cm~(-2)的模拟太阳光下超过720 min,保持初始效率的71%以上且趋于稳定.     

TiO2/SnO2 electron transport double layers with ultrathin SnO2 for efficient planar perovskite solar cells

The electron transport layer (ETL) plays an important role on the performance and stability of perovskite solar cells (PSCs). Developing double ETL is a promising strategy to take the advantages of different ETL materials and avoid their drawbacks. Here, an ultrathin SnO₂ layer of ～ 5 nm deposited by atomic layer deposit (ALD) was used to construct a TiO₂/SnO₂ double ETL, improving the power conversion efficiency (PCE) from 18.02% to 21.13%. The ultrathin SnO₂ layer enhances the electrical conductivity of the double layer ETLs and improves band alignment at the ETL/perovskite interface, promoting charge extraction and transfer. The ultrathin SnO₂ layer also passivates the ETL/perovskite interface, suppressing nonradiative recombination. The double ETL achieves outstanding stability compared with PSCs with TiO₂ only ETL. The PSCs with double ETL retains 85% of its initial PCE after 900 hours illumination. Our work demonstrates the prospects of using ultrathin metal oxide to construct double ETL for high-performance PSCs.     

Probability of a ductile fracture

The present paper studies ductile fracture by a random fractal and calculates the fracture probability q of a ductile fracture. The fracture probability q is sensitive to the number n (microvoid size) and the probability p of forming microvoids. There are two critical probabilities p_c1 and p_c2. When pp_c2 = 1-1/n², the fracture probability q is 100%, the ductile fracture occurs with probability 1; when p_c2 > p>p_c1, there is a positive probability q (1>q>0), the fracture probability q increases with increasing probability p and/or decreasing number n; when p<p_c1, the fracture probability q is zero (in fact less than 0.00001), the fracture does not occur. The critical probabilities p_c1 and p_c2 increase with increasing n. When 1-1/n²>p>1-1/n, though a ductile fracture does not occur, there is at least a macrovoid which passes through the transverse plane of the specimen.