纳米SiO2改性超高分子量聚乙烯纤维的制备及其结构性能研究

采用萃取阶段加入纳米粒子的方式,制得纳米SiO2改性的超高分子量聚乙烯(UHMWPE)纤维.借助于扫描电镜、声速法、WAXD、DSC、TMA和强力测试等手段,研究了纳米SiO2对UHMWPE纤维结构和性能的影响.结果表明,纳米SiO2粒子在UHMWPE纤维中可达到均匀分散,分散尺寸约为50～100nm;改性后纤维取向度、结晶度基本不变,纤维横向晶粒尺寸大大降低,纤维力学强度稍有增加,力学模量大大增加(由1359.2cNdtex增加到1505.9cNdtex),同时,纤维热性能和热力学性能也得到大大改善.     

聚二氧杂环己酮合成可吸收缝合线体外降解研究

通过检测缝线的力学性能、分子量、失重、大分子取向和结晶度变化研究了聚二氧杂环己酮可吸收缝合线（ＰＤＳ）在体外的初期（４星期）降解过程。研究结果表明，本文工艺条件下研制的ＰＤＳ缝线在体外降解过程中随着分子量和大分子取向程度下降，力学性能明显下降，４星期时强度基本消失。分子量明显下降而失重变化很小的结果，证明ＰＤＳ缝线的酯水解在链中和链端等活性，水解的几率只与水分子的可及程度相关。ＷＡＸＤ和ＤＳＣ测试结果表明，随着体外降解进行，缝线原晶区基本保持不变，无定形区产生新的有序区，并且含量不断增加和完善。采用结晶高聚物微原纤结构模型解释ＰＤＳ缝线无定形区在水中的降解机理与研究结果相吻合。ＰＤＳ缝线的体外降解机理与聚羟基乙酸（ＰＧＡ）缝线基本相同     

The influence of chitin nanocrystals on structural evolution of ultra-high molecular weight polyethylene/chitin nanocrystal fibers in hot-drawing process

Ultra-high molecular weight polyethylene (UHMWPE)/chitin nanocrystal (CNC) fibers were prepared. Compared with the pure UHMWPE fibers, the ultimate tensile strength and Young’s modulus of UHMWPE/CNC fibers are improved by 15.7% and 49.6%, respectively, with the addition of chitin nanocrystals (CNCs) of 1 wt%. The melting temperature (T _m) of UHMWPE/CNC fibers was higher than that of pure UHMWPE fibers. Pure UHMWPE fibers and UHMWPE/CNC fibers were characterized with respect to crystallinity, orientation and kebab structure by wide-angle X-ray diffraction (WAXD), small-angle X-ray scattering (SAXS) and scanning electron microscopy (SEM). It is found that the CNCs act as the shish structure in UHMWPE/CNC fibers and the kebab crystals are grown around the CNCs. There was almost no difference between pure UHMWPE fibers and UHMWPE/CNC fibers in orientation. But the degree of crystallinity of various stages of UHMWPE/CNC fibers was respectively higher than the corresponding stage of pure UHMWPE fibers. Moreover, the addition of 1 wt% CNCs improved the thickness of kebab crystals and accelerated the transformation of kebab to shish.     

EFFECT OF COMPATIBILITY ON PHASE MORPHOLOGY AND ORIENTATION OF ISOTACTIC POLYPROPYLENE （IPP） BLENDS OBTAINED BY DYNAMIC PACKING INJECTION MOLDING

The effect of compatibility on phase morphology and orientation of isotactic polypropylene （iPP） blends under shear stress was investigated via dynamic packing injection molding （DPIM）. The compatibility of iPP blended with other polymers, namely, atactic polypropylene （aPP）, octane-ethylene copolymer （POE）, ethylene-propylene-diene rubber （EPDM） and poly（ethylene-co-vinyl acetate） （EVA）, have first been studied using dynamic mechanical analysis （DMA）. These blends were subjected to DPIM, which relies on the application of shear stress fields to the melt/solid interfaces during the packing stage by means of hydraulically actuated pistons. The phase morphology, orientation and mechanical properties of the injection-molded samples were characterized by SEM, 2D WAXS and Instron. For incompatible iPP/EVA blends, a much elongated and deformed EVA particles and a higher degree of iPP chain orientation were observed under the effect of shear. However, for compatible iPP/aPP blends, a less deformed and elongated aPP particles and less oriented iPP chains were deduced. It can be concluded that the compatibility between the components decreases the deformation and orientation in the polymer blends. This is most likely due to the hindering effect, resulting from the molecular entanglement and interaction in the compatible system.     

Thermal characterization and electrical properties of Fe-modified cellulose long fibers and micro crystalline cellulose

Thermal properties of polylactic acid (PLA) filled with Fe-modified cellulose long fibers (CLF) and microcrystalline cellulose (MCC) were studied using thermo gravimetric analysis (TG), differential scanning calorimetry, and dynamic mechanical analysis (DMA). The Fe-modified CLFs and MCCs were compared with unmodified samples to study the effect of modification with Fe on electrical conductivity. Results from TG showed that the degradation temperature was higher for all composites when compared to the pure PLA and that the PLA composites filled with unmodified celluloses resulted in the best thermal stability. No comparable difference was found in glass transition temperature (T _g) and melting temperature (T _m) between pure PLA and Fe-modified and unmodified CLF- and MCC-based PLA biocomposites. DMA results showed that the storage modulus in glassy state was increased for the biocomposites when compared to pure PLA. The results obtained from a femtostat showed that electrical conductivity of Fe-modified CLF and MCC samples were higher than that of unmodified samples, thus indicating that the prepared biocomposites have potential uses where conductive biopolymers are needed. These modified fibers can also be tailored for fiber orientation in a matrix when subjected to a magnetic field.     

碳纳米管改性聚苯硫醚熔纺纤维的结构与性能研究

将多壁碳纳米管(MWCNTs)和聚苯硫醚(PPS)经过熔融挤出后制备成复合材料切片,并采用熔融纺丝法制得碳纳米管改性聚苯硫醚复合纤维.采用扫描电镜(SEM)、拉曼光谱、示差扫描量热分析(DSC)、动态机械分析(DMA)以及力学性能测试等表征手段研究了复合纤维中碳管的分散状态,与基体的界面作用,复合纤维的结晶性能以及力学性能,从而探讨了聚苯硫醚/碳纳米管复合纤维体系的微观结构与宏观性能之间的关系.研究表明,聚苯硫醚分子结构与碳纳米管之间具有的π-π共轭作用使碳管较为均匀的分散在基体中,界面结合较为紧密.同时熔融纺丝过程中的拉伸作用使碳管进一步解缠并使碳管沿纤维拉伸方向取向.另一方面,拉曼光谱显示拉伸作用有效地增强了界面作用,有利于外界应力的传递.碳管的良好分散以及强的界面作用使复合纤维力学性能得到大幅度的提高,当碳管含量达到5 wt%时,复合纤维的模量有了明显的提高,拉伸强度较纯PPS纤维提高了近220%.     

Properties,Morphology and Structure of BPDA/PPD/TFMB Polyimide Fibers

The mechanical properties of fibers were notably improved by incorporating 2,2′-bis(trifluoromethyl)- benzidine(TFMB) into 3,3′,4,4′-biphenyltetracarboxylic dianhydride(s-BPDA) and p-phenylenediamine(PPD) backbone. The best strength and modulus of BPDA/PPD/TFMB polyimide(PI) fiber(diamine molar ratio of PPD/TFMB= 90/10) were 1.60 and 90 GPa, respectively, which was over two times that of BPDA/PPD PI fiber. SEM image showed that the cross-section of fibers at each stage was round and voids free. Besides, the “skin-core” and microfibrillar structure were not observed. The thermal properties of PI fibers were also investigated. The results showed that the fibers owned excellent thermal stability, moreover, the structural homogeneity of fibers were significantly improved by heat-drawn stage. The T_g values were found to be around 300℃ by dynamic mechanical analysis(DMA). Wide angle X-ray diffraction(WAXD) and small angle X-ray scattering(SAXS) experiments indicated that the order degree of longitudinal and lateral stacks, the molecular orientation and the structural homogeneity of fibers were improved in the preparation process of fibers.     

Compatibilization of polypropylene/poly(glycolic acid) blend with maleated poe/attapulgite hybrid compatibilizer: Evaluation of mechanical,thermal, rheological,and morphological characteristics

In this work, the compatibilization effects of hybrid maleated POE/attapulgite hybrid compatibilizer (M-POE/ATP) on the immiscible polypropylene/poly(glycolic acid) (PP/PGA) blends was investigated. The hybrid compatibilizer integrating strengthening, toughening and compatibilization functions was prepared via one-step reactive extrusion using peroxidated ATP as the initiator. Then, the effects of compatibilizer dosage on the mechanical, thermal, rheological and morphological characteristics of blends were evaluated in detail. It was found that the hybrid compatibilizer resulted in the significantly enhanced compatibility and mechanical performance. Increased amount of compatibilizer content fractionated and almost wholly suppressed the crystallization process of PGA. The compatibilized blends showed higher thermal stability than pure PGA, and lower storage modulus and complex viscosity at higher shearing frequency. PGA in the blends presented a much lower degradation rate, which lead to the higher strength retention of 81% for the blend with 4 wt% of compatibilizer in buffer solution after 35 days.     

Effect of starch content on the biodegradation of polycaprolactone/starch composite for fabricating in situ pore-forming scaffolds

Bone tissue engineering is an efficient approach to regenerating bone-related defects. The optimal scaffold used for bone tissue engineering must possess adequate porosity and suitable mechanical properties. This work described the development of a biodegradable polymeric composite based on polycaprolactone (PCL) and starch that can form a porous structure in situ. The scaffold exhibited the required mechanical properties at the initial stage of implantation by controlling in situ degradation and subsequent pore formation. PCL/starch (SPCL) scaffolds with 100/0, 70/30, and 50/50 ratios were developed. Degradation studies were performed in phosphate buffer saline (PBS) containing α-amylase or lipase at 37 °C for 4 weeks. Fourier-transform infrared spectroscopy was used to analyze chemical bonds and their changes after degradation. Differential scanning calorimetry was applied to determine the crystallinity and recrystallization of samples before and after degradation. Mass loss and starch release were observed during degradation, and the porosity of samples was measured by the ethanol replacement method. Morphology was further determined using scanning electron microscopy. Finally, variations in compressive strength and modulus during degradation and pore formation were also measured. The porosity of samples reached 45% after 1 month of degradation, and mechanical properties were still appropriate for human bone tissue. Reduction in mechanical property after mass loss, starch release and pore formation was controlled by the hydrogen bonding and recrystallization effect of PCL after degradation. Results suggested that SPCL composite had potential to form porous scaffold with adequate mechanical properties in situ and is promising for bone tissue engineering applications.     

Influence of metal ion on the degradation of LDPE at the composting temperatures

Low Density Polyethylene(LDPE) films with additives that contain metal ions were subjected to accelerated degradation at simulated composting temperatures. The mechanical properties and viscosity-average molecular weight of the samples, during the degradation, were determined and the degradation mechanism was studied. The results show that the samples containing metal ion show considerable decreases. Percentage crystallinity of LDPE in the samples has changed obviously during the degradation. [POOH] increases during the early stage of degradation followed by a more or less flat maximum before it starts to decrease, but carbonyl index shows a polynomial increase during the degradation.     

共聚酯型热熔粘结纤维结晶结构及其熔融行为

采用DSC与WAXD相结合的方法研究了两个系列的无规嵌段共聚酯型热熔粘结纤维的结晶结构并探讨了系列样品的熔融行为.实验表明,以最低熔融温度为界,可将样品分为两组,每组只含一种可结晶单元的结晶.其结构与物理机械性质随该可结晶单元的加入量而有规律的变化.纤维的粘结性能则取决于非晶区结构,非晶区分子链柔性增加,会明显改善粘结效果.     

在低频振动场中注塑成型iPP试样的结构与性能研究

利用自行研制的低频振动注塑成型装置进行等规聚丙烯(iPP)试样的结构与性能研究.实验中对常规注射和振动注射成型的试样力学性能和微观形态进行了对比实验.采用低频振动注塑成型工艺实现了IPP试样的自增强,在190℃下进行注射,强度由常规试样的41.3 MPa最大提高到振动试样的48.4 MPa(振幅PA=59.4 MPa,振频FR=0.7 Hz),强度提高了17.2%;SEM显示常规试样芯层结构主要由球晶构成,振动注射使球晶在流动方向上变形、取向,晶粒尺寸得到细化;DSC表明振动注射促进熔融峰向高温漂移,晶体结晶更加完善,结晶度最大提高了12.1%;WAXD显示低频大振幅振动注塑有利于γ晶型的生成,γ晶型有利于试样实现自增强.     

Enzymatic degradation of poly(L-lactide) and poly(epsilon-caprolactone) electrospun fibers

Poly(L-lactide) (PLLA) and poly(epsilon-caprolactone) (PCL) ultrafine fibers were prepared by electrospinning. The influence of cationic and anionic surfactants on their enzymatic degradation behavior was investigated by measuring weight loss, molecular weight, crystallinity, and melting temperature of the fibers as a function of degradation time. Under the catalysis of proteinase K, the PLLA fibers containing the anionic surfactant sodium docecyl sulfate (SDS) exhibited a faster degradation rate than those containing cationic surfactant triethylbenzylammonium chloride (TEBAC), indicating that surface electric charge on the fibers is a critical factor for an enzymatic degradation. Similarly, TEBAC-containing PCL fibers exhibited a 47% weight loss within 8.5 h whereas SDS-containing PCL fibers showed little degradation in the presence of lipase PS. By analyzing the charge status of proteinase K and lipase PS under the experimental conditions, the importance of the surface charges of the fibers and their interactions with the charges on the enzymes were revealed. Consequently, a "two-step" degradation mechanism was proposed: (1) the enzyme approaches the fiber surface; (2) the enzyme initiates hydrolysis of the polymer. By means of differential scanning calorimetry and wide-angle X-ray diffraction, the crystallinity and orientation changes in the PLLA and PCL fibers during the enzymatic degradation were investigated, respectively.     

TEXTURE AND CRYSTALLINITY EVOLUTION IN ISOTACTIC POLYPROPYLENE INDUCED BY ROLLING AND THEIR INFLUENCE ON MECHANICAL PROPERTIES

The orientation and crystallinity evolution of isotactic polypropylene （iPP） induced by rolling were studied using wide angle X-ray scattering with an area detector. The tensile mechanical properties of rolled isotactic polypropylene sheets were also measured in this work. The texture component method was used to analyze the rolling texture. The rolling texture consists mainly of （010）[001], （130）[001] and [001]//RD fiber components in the sample with a rolling true strain of 1.5. The results reveal that crystallinity drastically decreases during rolling. It is suggested that amorphization is a deformation mechanism which takes place as an alternative to crystallographic intralamellar slip depending on the orientation of the lamellae. Both the orientation and crystallinity affect the tensile mechanical properties of rolled polypropylene. Crystallinity influences the elastic modulus on both directions and yield strength on transverse direction at the first stage of deformation. Orientation is the main reason for the changes of mechanical properties, especially at the latter part of deformation. The changes of both tensile strength and elongation percentage on rolling direction are larger than those on transverse direction, which results from the orientation. At last, the anisotropic mechanical properties occur on the rolling and transverse direction： high tensile strength with low elongation percentage on rolling direction and low tensile strength with high elongation percentage on transverse direction.     

聚对苯二甲酰对苯二胺纤维的热老化行为与机理研究

在250～400℃空气中对自由状态下对位芳纶进行等温热老化处理,采用万能材料试验机、红外光谱法、广角X射线衍射法、声速法和特性黏数法表征了老化过程中力学性能和结构的变化.结果表明,在老化初期,由于分子链的解取向,强度随时间快速下降;随后的热分解使强度随老化时间继续降低,符合二级反应动力学模型,其热老化表观活化能为32.4kJ/mol.老化样品的强度随温度升高显著下降,但高于350℃时热交联反应变得明显,同时结晶度增大和结晶结构完善,使强度的损失速率减小.老化样品的模量随老化温度的升高而增大,低于350℃时,非晶态分子链的解取向占优,模量较未热老化样品低;升高至350℃时,结晶结构完善占优,表现在第二类晶格畸变参数降低、表观微晶尺寸增大,特别是微晶横向融合使a,b轴方向尺寸显著增大,模量明显高于未老化样品.     

PET/PTT双组分弹性长丝的结晶取向结构和卷曲性能

为研制军官礼服用PET/PTT双组分弹性长丝,在纺丝加工工艺研究的基础上,通过声速法、WAXD、DSC、Instron5566对典型工艺下的弹性长丝进行了结晶和取向结构及卷曲性能的测试分析.在可纺的前提下,PET/PTT两组分复合纺丝中,PET组分优先结晶,具有高于其单组分纤维的拉伸诱导取向和结晶;而PTT组分只有形变,其结晶度和晶区取向均低于其对应的单组分纤维.在实验条件范围内,两组分粘度差异越大,纤维的卷曲伸长率和收缩率越大、声速取向因子增加、各单组分结晶度增加;两组分质量比为50/50时,纤维有最大的卷曲伸长率和收缩率,且各单组分结晶度随该两组分含量差异的增加而减少,而声速取向变化相反;随牵伸比的增加,纤维的整体取向、各组分结晶度均有所增加,卷曲伸长和收缩率也增加.牵伸温度和定型温度对双组分纤维的结构和卷曲性能影响较小.     

The effect of ionic electrolytes on hydrolytic degradation of biodegradable polymers: Mechanical and thermodynamic properties and molecular modeling

The purpose of this study was to examine the effect of electrolytes on the hydrolytic degradation of synthetic biodegradable polymers and fibers. Both Polyglycolic acid (PGA) and poly(glycolide–lactide) copolymer (PGL) were used for the study. Four different electrolytes were used: NaCl, LiCl, MgCl₂, and ZnCl₂. The electrolyte effect was evaluated in terms of the change in tensile properties, water uptake, and surface morphology of the polymers and fibers. It was found that the NaCl and MgCl₂ solutions significantly retarded the hydrolytic degradation of both PGA and PGL as evidenced in the prolonged retention of tensile breaking strength of these fibers when compared to deionized water control. Increasing the concentration of the electrolyte retarded the hydrolytic degradation rate further. These mechanical property data agreed well with the rate and amount of water uptake of PGA and could be correlated with the chemical potential difference of water between the electrolyte solution and pure water. The effect of electrolyte was further analyzed by theoretical calculation. Semiemperical molecular orbital calculations indicated that hard cations like Mg, Li, and Zn strongly coordinated to the polar sites of the polymer chain segments (? C?O) and severely disrupted their solvation spheres. Such a disruption was reflected in the smaller amount and slower rate of water uptake by PGA, and thus a slower rate of hydrolytic degradation as evident in the retention of tensile breaking strength. © 1993 John Wiley & Sons, Inc.     

Effect of short glass fiber on structure and viscoelastic behavior of olefinic polymers synthesized with metallocene catalyst

Several composites were prepared on the basis of an ethylene homopolymer and different copolymers of ethylene and 1‐hexene, synthesized with a metallocene catalyst, as matrices and a content of a 5 wt % of short glass fiber. The effect of the fiber incorporation on the structure and mechanical and viscoelastic behaviors was analyzed for the different samples. The glass fibers induced a slightly higher crystallinity, and the crystallite morphology significantly changed (long spacings and crystal orientation). The incorporation of fibers did not reinforce the different matrices under study at this low content; consequently, the mechanical parameters, such as Young's modulus, yielding stress, and microhardness, were lower in the composites as compared with those values found in the neat polyolefins. The location and apparent activation energies of distinct relaxation processes are also discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1244–1255, 2003     

Effects of force and simulated body fluids on oxidative degradation and mechanical properties of ultrahigh molecular weight polyethylene

The change in oxidative degradation and mechanical properties of ultrahigh molecular weight polyethylene (UHMWPE) samples was evaluated. The percentage of crystallinity, chemical composition, and wetting properties were performed on different UHMWPE samples. Experimental results showed that the percentage of crystallinity and O/C ratio increased after immersion in simulated body fluids (SBF) for 5 years, and this resulted in lower mechanical properties. A coarse surface quality of UHMWPE surface caused lower contact angle and higher initial friction coefficient after the coeffect of force and SBF, but other mechanical properties changed little. The wear mechanism changed when immersed in SBF for 5 years.     

TAILORING TISSUE ENGINEERING SCAFFOLDS USING ELECTROSTATIC PROCESSING TECHNIQUES: A STUDY OF POLY(GLYCOLIC ACID) ELECTROSPINNING

Poly(glycolic acid) (PGA) has long been a popular polymer in the tissue engineering field. PGA possesses many favorable properties such as biocompatibility, bioabsorbability, and tensile strength. The traditional fiber formation techniques of melt extrusion and cold-drawing are generally limited to fibers of 10–12 μm in diameter. Electrostatic spinning, or electrospinning, is an attractive approach for the production of much smaller diameter fibers which are of interest as tissue engineering scaffolds. We demonstrate the ability to control the fiber diameter of PGA as a function of solution concentration and fiber orientation, as well as show a correlation between the fiber orientation, elastic modulu, and strain to failure of PGA in a uniaxial model.