Bending strength of oriented glass-reinforced plastics

The authors consider the effect of the low shear strength and shear stiffness of oriented glass-reinforced plastics (GRP) on the stress distribution and type of failure in bending. On the basis of relations obtained in [1] it is shown that the effect of shears on the magnitude and law of distribution of the normal and shear stresses is important only for very short beams made of materials with a low shear stiffness. An experimental study of the nature of failure in bending has revealed that the chief cause of extension of the region of shear failure of oriented GRP is the low shear strength of the material, and has made it possible to establish the limits of this region for three typical materials. Anisotropy of the elastic properties has little effect on the type of failure in bending.Mekhanika Polimerov, Vol. 2, No. 4, pp. 535–542, 1966     

Experimental estimation of the effect of transverse shears on the bending of plates made of oriented glass-reinforced plastics

The results of experiments on square, freely supported plates of oriented glass-reinforced plastic are reported. The results obtained are compared with theoretical formulas based on hypotheses less rigorous than the Kirchhoff-Love hypothesis.Mekhanika Polimerov, Vol. 3, No. 1, pp. 146–150, 1967     

Fiber distribution in oriented glass-reinforced plastics

The distribution of the fibers in the structure of a glass-reinforced plastic has been experimentally investigated. Data have been obtained on the distribution of interfiber distances, fiber diameters, and the angles between the lines of centers. Experimental histograms and distribution curves are constructed.Institute of Mechanics, Academy of Sciences of the Ukrainian SSR, Kiev. Translated from Mekhanika Polimerov, Vol. 5, No. 2, pp. 282–287, March–April, 1969.     

Structural residual stresses in oriented glass-reinforced plastics

A previously proposed method is used to obtain expressions for calculating the residual stresses as a function of the physicomechanical properties of the polymer matrix and the reinforcement ratio. The calculation results are presented and the corresponding state of stress and strain analyzed. There are considerable deviations (in the magnitude and distribution of the stresses) from models that neglect or only take partly into account the interaction of the fibers.Moscow Ordzhonikidze Aviation Institute. Translated from Mekhanika Polimerov, Vol. 4, No. 6, pp. 1051–1058, November–December, 1968.     

Theory of shrinkage stresses in oriented glass-reinforced plastics

The problem of shrinkage stress distribution in glass-reinforced plastics is examined on the basis of an improved model under certain assumptions concerning the nature of the curing process. Cylindrical tubes of epoxy glass-reinforced plastic are investigated under stepped temperature conditions.Mekhanika Polimerov, Vol. 1, No. 6, pp. 61–68, 1965     

Mechanical characteristics of oriented glass-reinforced plastics in shear

The mechanical characteristics of oriented glass-reinforced plastics stressed in shear are considered. Various methods of determining them are compared. The dispersion of the shear strength is characterized and the possibility of glass-reinforced plastics elements failing as a result of low interlaminar shear strength is discussed.Moscow Aviation Technological Institute. Translated from Mekhanika Polimerov, No. 6, pp. 1008–1013, November–December, 1969.     

Shear effects during bending of oriented glass-reinforced plastics

An oriented glass-reinforced plastic may be treated as a regular multilayer material. Given large number of layers we can replace the discrete model with a continuous medium whose elastic constants are determined by the properties of the components. Using this approach and assuming that the reinforcing and the resin obey Hooke's law, we examine the problem of the bending of oriented glass-reinforced plastics and by means of two examples demonstrate the importance of shear effects in the bending of beams. The experimental results are in good agreement with theory.Mekhanika Polimerov, Vol 1, No. 2, pp. 38–46, 1965     

Distortion of cross sections during deformation of oriented glass-reinforced plastics

Test pieces equipped with wire strain gauges were used to investigate the distortion of cross sections of bars made of oriented glass-reinforced plastics (GRP) in tension and bending. The need for modified design formulas, obtained without use of the simplifying hypothesis of plane sections, is demonstrated. The previously obtained theoretical results of [2, 3] are experimentally confirmed. The effect of the free ends on beam deflection is found to be unimportant.Mekhanika Polimerov, Vol. 1, No. 5, pp. 107–113, 1965     

Effect of residual stresses on the strength of oriented glass-reinforced plastics

The effect of structural residual stresses on the strength of a glass-reinforced plastic loaded along and across the fibers is investigated. It is established that the residual stresses lead to an increase in the strength of the glass-reinforced plastic across the fibers and to cracking of the polymer matrix in tension along the fibers, but have practically no effect on the combined deformation of the matrix and the fibers in compression.Moscow Ordzhonikidze Aviation Institute. Translated from Mekhanika Polimerov, No. 3, pp. 475–480, May–June, 1969.     

Propagation of elastic waves along the fibers in oriented glass-reinforced plastics

The dispersion equation is derived for axisymmetric (longitudinal and torsional) normal vibrations in oriented glass-reinforced plastics. The low-frequency case is examined in detail. The frequency limits of applicability of the method of substituting a homogeneous medium for the composite (GRP) are estimated. The dependence of the vibration propagation velocity on glass content is calculated.Leningrad Zonal Scientific-Research Institute of Experimental Design of Public and Residential Buildings. Translated from Mekhanika Polimerov, No. 6, pp. 976–983, November–December, 1973.     

Creep and long-time strength of oriented glass-reinforced plastics in interlaminar shear

The creep and long-time strength in interlaminar shear and the creep in compression in the direction of the reinforcement have been experimentally investigated for certain types of oriented glass-reinforced plastics. The specimens in the interlaminar creep tests took the form of short beams loaded in bending. The experimental creep data for shear and compression are well described by the hereditary theory with a kernel of the Abel type (shear) or in the form of a Rabotnov function (compression). If the stresses are constant in time, good agreement with experiment is also given by Findley's form of the aging theory. A deformation criterion of interlaminar shear strength is also obtained. The experimental curves and values of the creep and long-time strength constants are presented.Translated from Mekhanika Polimerov, No. 6, pp. 1003–1012, November–December, 1971.     

Concerning the mechanism of fracture of oriented glass-reinforced plastics in uniaxial compression

The mechanism of fracture of an oriented glass-reinforced plastic in uniaxial compression in various directions in the plane of the sheet is considered on the basis of experimental observations of the microstructure and data on the variation of the linear and volume strains with increasing load. It is shown that increases in load are accompanied by a steady increase in crack development and damage accumulation.Leningrad Structural Engineering Institute. Translated from Mekhanika Polimerov, No. 2, pp. 238–242, March–April, 1971.     

Effect of temperature and anisotropy on the elastic constants of oriented glass-reinforced plastics

The experimental temperature dependence of the modulus of elasticity and Poisson's ratio are presented for SVAM oriented glass-reinforced plastic. The possibility of treating SVAM sheet as orthotropic at elevated temperatures is demonstrated.Institute of Chemical Physics, AS USSR, Moscow. Translated from Mekhanika Polimerov, Vol. 4, No. 6, pp. 1026–1032, November–December, 1968.     

Relation between the interlaminar shear modulus and thermal conductivity of oriented glass-reinforced plastics

The relation between the interlaminar shear modulus G of oriented glass-reinforced plastics and their thermal conductivity in a direction orthogonal to the plane of reinforcement is investigated. It is shown that G can be predicted from the measured values of and the bending deformations from and the propagation velocity of ultrasound.Institute of Polymer Mechanics, Academy of Sciences of the Latvian SSR, Riga. Translated from Makhanika Polimerov, No. 6, pp. 985–989, November–December, 1970.     

Statistical strength of glass-reinforced plastics

The failure of glass-reinforced plastics is treated as an aggregate of successive failures of the individual fibers. A method of estimating the statistical strength from the distribution curve is proposed.Mekhanika Polimerov, Vol. 3, No. 3, pp. 498–502, 1967     

Programmed winding of glass-reinforced plastics

It is proposed to employ a variable winding tension designed to give a required initial stress distribution. The program is constructed on the basis of solutions describing the loss of tension associated with winding and the softening of the resin during heat treatment. The problems are solved in the elastic formulation. Programs are obtained for three cases: constant tension in a ring sill on the mandrel, compensation of the stresses that develop after removal from the mandrel, and compensation of the thermoelastic stresses that develop during cooling.Institute of Polymer Mechanics, Academy of Sciences of the Latvian SSR, Riga. Translated from Mekhanika Polimerov, No. 1, pp. 48–53, January–February, 1970.     

Static fatigue of glass-reinforced plastics

Nonlinear damage accumulation rules are usually constructed on the basis of certain hypotheses derived from semiempirical considerations. A method is proposed for constructing an averaged nonlinear damage accumulation rule based on the direct utilization of the results of static fatigue tests on glass-reinforced plastic specimens. Numerical examples of the calculation of the static fatigue strength under repeat loading with a given strength criterion are presented.Sverdlovsk Branch of the Steklov Mathematical Institute, Academy of Sciences of the USSR. Institute of Polymer Mechanics, Academy of Sciences of the Latvian SSR, Riga. Translated from Mekhanika Polimerov, No. 3, pp. 492–497, May–June, 1969.     

Relaxation characteristics of glass-reinforced plastics

A study was made of the relaxation properties of glass-reinforced plastics KAST-V, ÉDF, SVAM, and Textolite. The article gives experimental and theoretical values of the pliabilities and tables of the values of the relaxation properties required for the solution of boundary value problems in viscoelasticity.M. V. Lomonosov State University, Moscow. Translated from Mekhanika Polimerov, No. 3, pp. 560–562, May–June, 1970.     

Tensile tests on glass-reinforced plastics

The mechanism of failure of glass-reinforced plastics in short-time tensile tests is considered from the statistical viewpoint. It is thus possible to calculate for various materials the damage suffered by the test piece up to failure. This depends on the dispersion of the static properties but not on the absolute dimensions.Mekhanika Polimerov, Vol. 1, No. 2, pp. 93–103, 1965