Photoacoustic spectroscopy of thin films of As<Subscript>2</Subscript>S<Subscript>3</Subscript>, As<Subscript>2</Subscript>Se<Subscript>3</Subscript> and GeSe<Subscript>2</Subscript>

Photoacoustic spectroscopy (PAS) is one of the important branches of spectroscopy, which enables one to detect light-induced heat production following the absorption of pulsed radiation by the sample. As₂S₃, As₂Se₃ and GeSe₂ exhibit a wide variety of photo-induced phenomena that enable them to be used as optical imaging or storage medium and various electronic devices, including electro-optic information storage devices and optical mass memories. Therefore, accurate measurement of thermal properties of semiconducting films is necessary to study the memory density. The thermal conductivity of thin films of As₂S₃ (thickness 100 μm and 80 μm), As₂Se₃ (thickness 100 μm and 80 μm) and GeSe₂ (thickness 120 μm and 100 μm) has been measured using PAS technique. Our result shows that the thermal conductivity of thicker films is larger than the thinner films. This can be explained by the thermal resistance effect between the film and the surface of the substrate.      

Reversible photo-induced volume changes in evaporated As2S3 and As4Se5Ge1 films

Reversible photo-induced volume changes have been observed accompanying reversible optical absorption edge shift produced by successive cycles of band gap illumination and annealing for well-annealed evaporated As₂S₃ and As₄Se₅Ge₁ films. The As₂S₃ film shows an increase in its volume by illumination, while As₄Se₅Ge₁ film shows a decrease. Qualitative discussion has been given in connection with pressure-induced optical constant change.     

Magnetotransport in thin epitaxial Bi<Subscript>2</Subscript>Se<Subscript>3</Subscript> films

The magnetoconductivity of thin Bi₂Se₃ films covered by a protective Se layer and grown at (111) BaF₂ substrates is studied. It is shown that the negative magnetoconductivity observed at low magnetic fields and caused by the effect of weak antilocalization, as well as the Shubnikov?de Haas oscillations at higher fields, is determined only by the magnetic field component perpendicular to the film plane. The obtained experimental results can be reasonably interpreted under the assumption that the studied films exhibit two-dimensional topologically protected electron states. Moreover, the contribution of these states to the total conductivity turns out to be the dominant one.     

Spin Polarization of Mn<Subscript>5</Subscript>Ge<Subscript>3</Subscript> in the Bulk and Thin Films

The intermetallic compound Mn₅Ge₃ is one of the promising materials for application as a source of charge carriers in spintronics. The existing experimental data on the spin polarization in Mn₅Ge₃ demonstrate significant discrepancies. All theoretical studies concern a Mn₅Ge₃ bulk crystal. At the same time, thin films are of interest for applications. In this work, ab initio calculations have been performed for a Mn₅Ge₃ thin film on a germanium substrate. The difference between the magnetic moments of manganese atoms, densities of states, and spin polarizations for the bulk crystal and thin film has been demonstrated.     

Electrical properties of a-Ge<Subscript>x</Subscript>Se<Subscript>100-<Emphasis Type="Italic">x</Emphasis></Subscript>

In general, the conductivity in chalcogenide glasses at higher temperatures is dominated by band conduction (DC conduction). But, at lower temperatures, hopping conduction dominates over band conduction. A study at lower temperature can, eventually, provide useful information about the conduction mechanism and the defect states in the material. Therefore, the study of electrical properties of Ge_xSe_100-x in the lower temperature region (room temperature) is interesting. Temperature and frequency dependence of Ge_xSe_{100-x (x} = 15, 20 and 25) have been studied over different range of temperatures and frequencies. An agreement between experimental and theoretical results suggested that the behaviour of germanium selenium system (Ge_xSe_100-x ) have been successfully explained by correlated barrier hopping (CBH) model.     

Electrical switching studies on As<Subscript>40</Subscript>Te<Subscript>60-x</Subscript>Se<Subscript>x</Subscript> and As<Subscript>35</Subscript>Te<Subscript>65-x</Subscript>Se<Subscript>x</Subscript> glasses

The I–V characteristics of bulk As₄₀Te_60-xSe_x and As₃₅Te_65-xSe_x glasses have been studied with a current sweep of 0–18 mA-0, over a wide range of compositions (4≤x≤22). All the glasses studied showed a threshold electrical switching behaviour. The number of switching cycles withstood by the samples has been found to depend on the ON-state current. It is seen that the switching voltages increase with increase in selenium content. Further, the switching voltages are found to be almost independent of the thickness of the sample (d), in the range 0.18–0.3 mm. Also, the switching voltages and the number of switching cycles withstood by the samples are found to decrease with temperature. Received: 6 November 2002 / Accepted: 8 November 2002 / Published online: 29 January 2003 RID="*" ID="*"Corresponding author. Fax: +91-80/360-0135, E-mail: sasokan@isu.iisc.ernet.in     

Photoplasticity of As2Se3 films investigated with combined nanoindentation and AFM methods

Thin As₂Se₃ amorphous chalcogenide films have been studied by nanoindentation and atomic force microscopy in darkness and under illumination by band-gap light. The combination of these two methods has been used to study the peculiarities of the photoplastic effect in amorphous semiconductors. It has been shown by multiple loading indentation experiments that a non-linear mechanism of the formation of the strain response is realized in the As₂Se₃ films subjected to the combined action of light and external mechanical loading. We have observed that light illumination alters the internal friction of the films and their shear modulus. These observations have been considered in the frame of the two-phase model of chalcogenide glasses. Some arguments in favor that the self-organization processes take place in the structure of irradiated film are given.     

Features of the electronic spectrum and optical absorption of ultrathin Bi<Subscript>2</Subscript>Se<Subscript>3</Subscript> films

The electronic spectra and relative permittivity of ultrathin (1–3 QL) films of Bi₂Se₃ topological insulator have been calculated by the density functional theory. The calculated spectra exhibit a characteristic feature: the range of 0.0–0.9 eV below the Fermi level contains two doubly degenerate valence bands (“U-bands”), which are geometrically congruent to low-lying spectral branches in the conduction band. It has been shown that the saturation of optical absorption can result in a significant rearrangement of the electronic structure and properties in the near infrared spectral range in the considered film. In particular, the semiconductor (in the absence of interaction with light) type of conductivity of the film can be changed to the metallic type of conductivity strongly nonlinear in the intensity of light.     

Magnetic properties of Pb<Subscript>2</Subscript>Fe<Subscript>2</Subscript>Ge<Subscript>2</Subscript>O<Subscript>9</Subscript> single crystals

Single crystals of Pb₂Fe₂Ge₂O₉ have been grown. They were subjected to X-ray diffraction, magnetic, neutron diffraction, Mössbauer and spin resonance studies. It has been established that Pb₂Fe₂Ge₂O₉ is a weak ferromagnet with a Néel temperature T _N = 46 K, and the exchange and spin-flop transition fields have been estimated. It has been demonstrated that the weak ferromagnetic moment is actually the result of the single-ion anisotropy axes for the magnetic moments of different magnetic sublattices being not collinear.     

Growth of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> films on the Si(111) surface covered by a thin SiO<Subscript>2</Subscript> layer

Magnetite polycrystalline films are grown by variously oxidizing a Fe film on the Si(111) surface covered by a thin (1.5 nm) SiO₂ layer. It is found that defects in the SiO₂ layer influence silicidation under heating of the Fe film. The high-temperature oxidation of the Fe film results in the formation of both Fe₃O₄ and iron monosilicide. However, the high-temperature deposition of Fe in an oxygen atmosphere leads to the growth of a compositionally uniform Fe₃O₄ film on the SiO₂ surface. It is found that such a synthesis method causes [311] texture to arise in the magnetite film, with the texture axis normal to the surface. The influence of the synthesis method on the magnetic properties of grown Fe₃O₄ films is studied. A high coercive force of Fe₃O₃ films grown by Fe film oxidation is related to their specific morphology and compositional nonuniformity.     

Selective wet etching of Ge<Subscript>2</Subscript>Sb<Subscript>2</Subscript>Te<Subscript>5</Subscript> phase-change thin films in thermal lithography with tetramethylammonium

In this paper, we study Ge₂Sb₂Te₅ phase-change film as a promising inorganic photoresist using organic alkaline: tetramethylammonium hydroxide (TMAH) solution, instead of inorganic alkali or acid as etchant. The basic etching properties are investigated by prior and posterior annealing Ge₂Sb₂Te₅ films. Selectivity is found to be dependent on concentration of TMAH. There is a good selectivity in the 25% TMAH solution, in which the amorphous state is etched away, whereas the crystalline state remains. The etching rate decreases when the concentration of TMAH is diluted; and an opposite selectivity, compared with 25% TMAH solution, is observed in the 0.125% TMAH solution. Selective etching with laser crystallization in different power levels is also studied, and an excellent wet selectivity in the 25% TMAH solution is obtained. The remaining crystalline lines are observed by atomic force microscopy. The surface roughness after etching is at a good level. The selective wet-etching mechanism is also discussed.     

Weak antilocalization in thin films of the Bi<Subscript>2</Subscript>Te<Subscript>2.7</Subscript>Se<Subscript>0.3</Subscript> solid solution

A technology has been developed for the preparation of thin films of the Bi₂Te_2.7Se_0.3 solid solution through the thermal evaporation in a vacuum using the “hot-wall” method. The high quality of the thin films thus prepared has been confirmed by the X-ray diffraction and Raman scattering data. The electron transport has been investigated over wide ranges of temperatures (1.4–300 K) and magnetic fields (up to 8 T). It has been assumed that the observed weak antilocalization is associated with the dominant contribution from the surface states of a topological insulator. The dephasing length has been estimated.     

Electronic structure,topological phase transitions and superconductivity in (K,Cs)<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Fe<Subscript>2</Subscript>Se<Subscript>2</Subscript>

We present LDA band structure of novel hole doped high temperature superconductors (T _c ∼ 30 K) K _x Fe₂Se₂ and Cs _x Fe₂Se₂ and compare it with previously studied electronic structure of isostructural FeAs superconductor BaFe₂As₂ (Ba122). We show that stoichiometric KFe₂Se₂ and CsFe₂Se₂ have rather different Fermi surfaces as compared with Ba122. However at about 60% of hole doping Fermi surfaces of novel materials closely resemble those of Ba122. In between these dopings we observe a number of topological Fermi surface transitions near the Γ point in the Brillouin zone. Superconducting transition temperature T _c of new systems is apparently governed by the value of the total density of states (DOS) at the Fermi level.     

Effect of heat treatment on the structure and the thermoelectric properties of Sb<Subscript>0.9</Subscript>Bi<Subscript>1.1</Subscript>Te<Subscript>2.9</Subscript>Se<Subscript>0.1</Subscript> thin films and composites based on them

This work considers the effect of vacuum annealing on the thermoelectric properties of Sb_0.9Bi_1.1Te_2.9Se_0.1 thin film and Sb_0.9Bi_1.1Te_2.9Se_0.1–C composites with various carbon contents produced by ion-beam deposition in an argon atmosphere. The electrical resistivity and the thermopower of Sb_0.9Bi_1.1Te_2.9Se_0.1–C nanocomposites are found to be dependent on not only the carbon concentration but also the type and the concentration of intrinsic point defects of the Sb_0.9Bi_1.1Te_2.9Se_0.1 solid solution, which determine the type of conductivity of Sb_0.9Bi_1.1Te_2.9Se_0.1 granules. The power factors are estimated for films of Sb_0.9Bi_1.1Te_2.9Se_0.1 solid solution and films of Sb_0.9Bi_1.1Te_2.9Se_0.1–C composites and found to have values comparable with the values for nanostructured materials on the basis of (Bi,Sb)₂(Te,Se)₃ solid solutions.     

Structure,the lattice dynamic,and the dielectric characteristics of Sr<Subscript>0.5</Subscript>Ba<Subscript>0.5</Subscript>Nb<Subscript>2</Subscript>O<Subscript>6</Subscript> films

Solid solution Sr_0.5Ba_0.5Nb₂O₆ films have been synthesized on a (111)Pt/(001)Si substrate by rf deposition in an oxygen atmosphere. The depolarized Raman spectra, the structure, and the dielectric characteristics of the films have been studied over a wide temperature range. It is found that the films were singlephase, had the tetragonal tungsten bronze structure, and had a pronounced axial texture with axis 001 directed perpendicular to the substrate surface. It is shown that the film material undergoes a diffuse phase transition to the state of a relaxor ferroelectric in the temperature range 300–425 K. Possible reasons of the regularities observed are discussed.     

Effect of thermal treatment on the thermoelectric properties of Sb<Subscript>0.9</Subscript>Bi<Subscript>1.1</Subscript>Te<Subscript>2.9</Subscript>Se<Subscript>0.1</Subscript> solid solution thin films

The effect thermal treatment in a vacuum has on the thermoelectric properties of Sb_0.9Bi_1.1Te_2.9Se_0.1 solid solution thin films obtained via ion-beam sputtering in an argon atmosphere is considered. It is established that the specific resistance and thermopower are determined by the type and concentration of intrinsic point defects of the Sb_0.9Bi_1.1Te_2.9Se_0.1 solid solution. The power factor values are found to be comparable to those of nanostructured materials based on (Bi,Sb)₂(Te,Se)₃ solid solutions.     

硫系非晶半导体薄膜中的超快光 Kerr效应

利用飞秒激光超外差光Kerr(OHD-OKE)技术研究了As₂S₃, As₂Se₃, GeS₂, GeSe₂, Ge₂₀As₂₅S₅₅, Ge₂₀As₂₅Se₅₅, Ge₁₀As₄₀S_{20关键词： 全光开关 硫系非晶半导体薄膜 飞秒激光超外差光Kerr(OHD-OKE) 三阶非线性}     

Geometries and electronic structures of Ga<Subscript>2</Subscript>Se<Subscript>3</Subscript>, Ga<Subscript>3</Subscript>Se<Subscript>2</Subscript> and their anions. Theoretical insights

We hereby report a theoretical study on the equilibrium geometries, electronic structures and harmonic vibrational frequencies of Ga₂Se₃, Ga₃Se₂ and their anions. The ground and low-lying excited states of Ga₂Se₃⁻, Ga₂Se₃, Ga₃Se₂⁻ and Ga₃Se₂ are studied at the B3LYP and/or MP2 and CCSD(T) levels in conjunction with 6-311+G(d) and 6-311+G(2df) one particle basis sets. Ga₂Se₂⁻ adopts the C_2v kite geometry while Ga₂Se₃ has a ‘V’ geometry. Ga₃Se₂⁻ has a three-dimensional ‘D_3h ’ geometry and Ga₃Se₂ prefers the three-dimensional ‘C_2v ’ structure. Electron detachment energies from the ground electronic states of the anions to several neutral states are reported and discussed. At CCSD(T)//MP2 level, the adiabatic electron affinity (AEA) of Ga₂Se₃ is calculated to be 3.23 eV when using the 6-311+G(2df) basis set and that of Ga₃Se₂ is 2.77 eV with the 6-311+G(d) basis set. The findings of this research are analyzed and compared with gallium oxide and sulfide analogues.     

Optical properties of films of the ternary compound CuIn<Subscript>3</Subscript>Se<Subscript>5</Subscript>

We have used the laser vaporization method to obtain films of the ternary compound CuIn₃Se₅ and have studied the composition and structure of the films obtained. We have determined the energy and nature of the optical transitions for the indicated compound from the transmission spectra in the region of the intrinsic absorption edge. We have calculated the valence-band crystal-field (Δ_CF) and spin-orbit (Δ_SO) splitting energies according to Hopfield’s quasicubic model for the ternary compound CuIn₃Se₅. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 1, pp. 82–85, January–February, 2007.     

Two-dimensional electron gas at the interface of Ba<Subscript>0.8</Subscript>Sr<Subscript>0.2</Subscript>TiO<Subscript>3</Subscript> ferroelectric and LaMnO<Subscript>3</Subscript> antiferomagnet

The temperature dependence of the electrical resistance has been studied for heterostructures formed by antiferromagnetic LaMnO₃ single crystals of different orientations with epitaxial films of ferroelectric Ba_0.8Sr_0.2TiO₃ deposited onto them. The measured electrical resistance is compared to that exhibited by LaMnO₃ single crystals without the films. It is found that, in the samples with the film, for which the axis of polarization in the ferroelectric is directed along the perpendicular to the surface of the single crystal, the electrical resistance decreases significantly with temperature, exhibiting metallic behavior below 160 K. The numerical simulations of the structural and electronic characteristics of the BaTiO₃/LaMnO₃ ferroelectric?antiferromagnet heterostructure has been performed. The transition to the state with two-dimensional electron gas at the interface is demonstrated.