The effect of humidity on sensitivity of amine detection in ion mobility spectrometry

Vaporized water molecules are unavoidably present in every ion mobility spectrometry (IMS) measurement. In general, this humidity is seen in positive mode IMS-spectra as protonated water clusters producing reactant ions. Clusters containing water molecules are also abundant among ions generated by an analyte. In this paper the influence of humidity on IMS-spectra was systematically investigated and determined by measuring different concentrations of a selected amine at various levels of humidity. The selected amine, trimethylamine (TMA), was chosen as the model analyte due to its atmospheric importance. During the measurements, surplus water vapor was introduced into the drift section inside the IMS instrument; the concentrations of both amine and water were adjusted by controlling the gas flows. The simultaneous presence of water vapor and analyte at various predefined concentrations revealed the sensitivity of the IMS-technique to water and the effect of moisture on the ion mobility distribution. The results indicated that the existence, positions and shapes of the peaks are strongly dependent on the amount of moisture. However, the sensitivity of detection is weakly dependent on humidity if this detection is based on monomer ion peak or the sum of peaks generated by the analyte, In addition, the main principles of the adjustment of sample and water concentrations are presented here.     

Corona Discharge Ion Mobility Spectrometry of Ten Alcohols

Ion mobility spectra for ten alcohols have been studied in an ion mobility spectrometry apparatus equipped with a corona discharge ionization source. Using protonated water cluster ions as the reactant ions and clean air as the drift gas, the alcohols exhibit different product ion characteristic peaks in their ion mobility spectra. The detection limit for these alcohols is at low concentration pmol/L level according to the concentration calibration by exponential dilution method. Based on the measured ion mobilities, several chemical physics parameters of the ion-molecular interaction at atmosphere were obtained, including the ionic collision cross sections, diffusion coefficients, collision rate constants, and the ionic radii under the hard-sphere model approximation.     

Monte Carlo Simulation of Ion Trajectories of Reacting Chemical Systems: Mobility of Small Water Clusters in Ion Mobility Spectrometry

For the comprehensive simulation of ion trajectories including reactive collisions at elevated pressure conditions, a chemical reaction simulation (RS) extension to the popular SIMION software package was developed, which is based on the Monte Carlo statistical approach. The RS extension is of particular interest to SIMION users who wish to simulate ion trajectories in collision dominated environments such as atmospheric pressure ion sources, ion guides (e.g., funnels, transfer multi poles), chemical reaction chambers (e.g., proton transfer tubes), and/or ion mobility analyzers. It is well known that ion molecule reaction rate constants frequently reach or exceed the collision limit obtained from kinetic gas theory. Thus with a typical dwell time of ions within the above mentioned devices in the ms range, chemical transformation reactions are likely to occur. In other words, individual ions change critical parameters such as mass, mobility, and chemical reactivity en passage to the analyzer, which naturally strongly affects their trajectories. The RS method simulates elementary reaction events of individual ions reflecting the behavior of a large ensemble by a representative set of simulated reacting particles. The simulation of the proton bound water cluster reactant ion peak (RIP) in ion mobility spectrometry (IMS) was chosen as a benchmark problem. For this purpose, the RIP was experimentally determined as a function of the background water concentration present in the IMS drift tube. It is shown that simulation and experimental data are in very good agreement, demonstrating the validity of the method.      

Ion mobility-mass spectrometry

This review article compares and contrasts various types of ion mobility-mass spectrometers available today and describes their advantages for application to a wide range of analytes. Ion mobility spectrometry (IMS), when coupled with mass spectrometry, offers value-added data not possible from mass spectra alone. Separation of isomers, isobars, and conformers; reduction of chemical noise; and measurement of ion size are possible with the addition of ion mobility cells to mass spectrometers. In addition, structurally similar ions and ions of the same charge state can be separated into families of ions which appear along a unique mass-mobility correlation line. This review describes the four methods of ion mobility separation currently used with mass spectrometry. They are (1) drift-time ion mobility spectrometry (DTIMS), (2) aspiration ion mobility spectrometry (AIMS), (3) differential-mobility spectrometry (DMS) which is also called field-asymmetric waveform ion mobility spectrometry (FAIMS) and (4) traveling-wave ion mobility spectrometry (TWIMS). DTIMS provides the highest IMS resolving power and is the only IMS method which can directly measure collision cross-sections. AIMS is a low resolution mobility separation method but can monitor ions in a continuous manner. DMS and FAIMS offer continuous-ion monitoring capability as well as orthogonal ion mobility separation in which high-separation selectivity can be achieved. TWIMS is a novel method of IMS with a low resolving power but has good sensitivity and is well intergrated into a commercial mass spectrometer. One hundred and sixty references on ion mobility-mass spectrometry (IMMS) are provided.     

Spray nebulization for sample introduction in ion mobility spectrometry

A new sample introduction system based on spray nebulization has been successfully developed to perform direct analysis of liquid samples by IMS. The system comprises a concentric nebulizer that generates a spray plume which is introduced in the ionization region of the IMS instrument through a temperature controlled transfer line. This system avoids previous problems of direct injection of liquid samples and maintains the countercurrent flow of inert gas necessary for the operation of the IMS instrument. Evaluation of the qualitative and quantitative capabilities of the methodology has been performed after a carefully study of the main variables affecting the spray nebulization and the transport of the analyte molecules through the transfer line. To demonstrate the usefulness of the new sample introduction system, direct analysis of drugs and drug metabolites in saliva or urine samples have been performed, obtaining accurate, reliable and sensitive results. Moreover, analytes with physico-chemical properties that limited the capability of thermal desorption as sample introduction method such as amino acids can be analyzed by using the spray nebulization methodology.     

Solid state chemical ionization for characterization of organic compounds by laser mass spectrometry

A new technique involving the addition of a compound to the analyte to serve as a source of "reagent" ions has been developed for negative-ion laser mass spectrometry. This "solid state chemical ionization" leads to ions characteristic of the analyte, owing to ion-molecule reactions between the "reagent" ion and the neutral analyte in the laser-generated plume. Polycyclic aromatic hydrocarbons show formation of an ion corresponding to (M + O - H)(-) in their negative-ion laser mass spectra when mixed with compounds such as sym-trinitrobenzene, sodium nitrate and sodium peroxide. NO(-)(2), O(-), and O(-)(2) serve as "reagent" ions in these compounds. Formation of (M + Cl)(-) is seen in the laser mass spectra of glycosides mixed with hexachlorobenzene. Chloride serves as the "reagent" ion in this case.     

Buffer gas additives (modifiers/shift reagents) in ion mobility spectrometry: Applications,predictions of mobility shifts,and influence of interaction energy and structure

Ion mobility spectrometry (IMS) is an analytical technique used for fast and sensitive detection of illegal substances in customs and airports, diagnosis of diseases through detection of metabolites in breath, fundamental studies in physics and chemistry, space exploration, and many more applications. Ion mobility spectrometry separates ions in the gas‐phase drifting under an electric field according to their size to charge ratio. Ion mobility spectrometry disadvantages are false positives that delay transportation, compromise patient's health and other negative issues when IMS is used for detection. To prevent false positives, IMS measures the ion mobilities in 2 different conditions, in pure buffer gas or when shift reagents (SRs) are introduced in this gas, providing 2 different characteristic properties of the ion and increasing the chances of right identification. Mobility shifts with the introduction of SRs in the buffer gas are due to clustering of analyte ions with SRs. Effective SRs are polar volatile compounds with free electron pairs with a tendency to form clusters with the analyte ion. Formation of clusters is favored by formation of stable analyte ion‐SR hydrogen bonds, high analytes' proton affinity, and low steric hindrance in the ion charge while stabilization of ion charge by resonance may disfavor it. Inductive effects and the number of adduction sites also affect cluster formation. The prediction of IMS separations of overlapping peaks is important because it simplifies a trial and error procedure. Doping experiments to simplify IMS spectra by changing the ion‐analyte reactions forming the so‐called alternative reactant ions are not considered in this review and techniques other than drift tube IMS are marginally covered.     

Formation of halide reactant ions and effects of excess reagent chemical on the ionization of TNT in ion mobility spectrometry

The efficiency of chloride reactant ion formation, when chlorinated hydrocarbon reagent chemicals were added to the ionization region of an ion mobility spectrometer, corresponded to the electron attachment rate constant of the chemical. The chemicals investigated here included chloromethane, dichlormethane, trichloromethane, tetrachloromethane and chlorobenzene, with tetrachloromethane producing the greatest amount of chloride reactant ions for the amount of chemical added. Reagent chemicals with smaller electron attachment rate constants required the addition of more chemical to reach functional reactant ion levels. The excess neutral reagent molecules clustered to the chloride reactant ions and reduced the effectiveness of abstracting a proton from 2,4,6-trinitrotoluene (TNT). The effect of clustering was different for each chemical. Tetrachloromethane, which had the least exothermic clustering reaction, had the most effective production of the (TNT-H)(-) product ion per mole of reagent chemical. Bromide and iodide ions were also investigated as potential reactant ions. Bromide was found to effectively produce the proton abstracted (TNT-H)(-) ion. Iodide, however, was not a strong enough base to form (TNT-H)(-) from TNT. There was no apparent transfer of an electron to TNT by chloride, bromide or iodide.     

Adduct-ion formation in trapped ion mobility spectrometry as a potential tool for studying molecular structures and conformations

Recent developments in the field of ion mobility spectrometry provide new possibilities to explore and understand gas-phase ion chemistry. In this study, hyphenated trapped ion mobility spectrometry-mass spectrometry (TIMS-MS) was applied to investigate analyte ion mobility as function of adduct ion formation for twelve pharmaceutically relevant molecules, and for tetrahydrocannabinol (THC) and its isomer cannabidiol (CBD). Samples were introduced by direct infusion and ions were generated with positive electrospray ionization (ESI+) observing protonated and sodiated ions. Measurements were performed with and without addition of cesium-, lithium-, silver- and sodium ions to the samples. For the tested compounds, metal adduct ions with the same m/z but with different mobility and collision cross section (CCSs) were observed, indicating different molecular conformations. Formation of analyte dimers was also observed, which could be associated with molecular geometry of the compounds. By optimizing the range and speed of the electric field gradient and ramp, respectively, the separation of THC and CBD was achieved by employing the adduct formation. This study demonstrates that the favorable resolution of TIMS combined with the ability to detect weakly bound counter ions is a valuable means for rapid detection, separation and structural assignment of molecular isomers and analyte conformations.     

Ion characterisation by comparison of ion mobility spectrometry and mass spectrometry data

The major uncertainty related to ion mobility spectrometry is the lack of knowledge about the characteristics of the ions detected. When using a radioactive atmospheric pressure ionisation source (e.g. ⁶³Ni), from theory proton bound water clusters are expected as reactant ions. When analyte ions occur, proton transfer should lead to proton-bound monomer and dimer ions. To increase the knowledge about those ionisation processes in an ion mobility spectrometer (IMS), a ß-radiation ionisation source was coupled to a mass spectrometer (MS) and an identical one to an IMS. Exemplarily, acetone, limonene and 2- and 5-nonanone were introduced into both instruments in varying concentrations. By correlating the MS and IMS spectra, conclusions about the identities of the ions detected by IMS could be drawn. Proton-bound monomer, dimer and even trimer ions (MH⁺, 2MH⁺, 3MH⁺) could be observed in the MS spectra for acetone and 5-nonanone and could be assigned to the related signals detected by IMS. The oligomers could be expected from theory for increasing concentration. Limonene and 2-nonanone yielded in a variety of different ions and fragments indicating complex gas phase ion chemistry. Those findings on the obviously different behaviour of different analytes require further research focussed on the ion chemistry in IMS including the comparison of different ionisation sources.     

If the ionization mechanism in fast-atom bombardment involves ion/molecule reactions, what are the reagent ions? The time dependence of fast-atom bombardment mass spectra and parallels to chemical ionization

The evaporation in vacuo of the matrices used and the particle-induced desorption of matrix molecules in fast-atom bombardment (FAB) contribute to a proposed high pressure region above the FAB matrix known as the selvedge region. If the neutral number density is sufficiently high, ions formed upon bombardment may undergo collisions with molecules, yielding matrix-related cluster ions and, in cases when the analyte is desorbed in neutral form, protonated and deprotonated analyte molecules. Similarities with the chemical ionization (CI experiment have been pointed out previously and are further developed here. If FAB is similar to CI, then the response depends on the structures of the reagent ions — those ions that react with gas phase analyte molecules. We consider here the time dependence of positive and negative ion FAB spectra to attempt to identify the reagent ions of FAB. A model is suggested for the FAB ion source which evaluates similarities to a CI source, as well as spatial aspects that are unique to desorption/ionization techniques.     

Simultaneous fragmentation of multiple ions using IMS drift time dependent collision energies

Ion mobility spectrometry coupled with mass spectrometry (IMS-MS) was utilized to evaluate an ion collision energy ramping technique that simultaneously fragments a variety of species. To evaluate this technique, the fragmentation patterns of a mixture of ions ranging in mass, charge state, and drift time were analyzed to determine their optimal fragmentation conditions. The precursor ions were pulsed into the IMS-MS instrument and separated in the IMS drift cell based on mobility differences. Two differentially pumped short quadrupoles were used to focus the ions exiting the drift cell, and fragmentation was induced by collision induced dissociation (CID) between the conductance limiting orifice behind the second short quadrupole and before the first octopole in the mass spectrometer. To explore the fragmentation spectrum of each precursor ion, the bias voltages for the short quadrupoles and conductance limiting orifices were increased from 0 to 50 V above nonfragmentation voltage settings. An approximately linear correlation was observed between the optimal fragmentation voltage for each ion and its specific drift time, so a linear voltage gradient was employed to supply less collision energy to high mobility ions (e.g., small conformations or higher charge state ions) and more to low mobility ions. Fragmentation efficiencies were found to be similar for different ions when the fragmentation voltage was linearly ramped with drift time, but varied drastically when only a single voltage was used.     

Evaluation of false positive responses by mass spectrometry and ion mobility spectrometry for the detection of trace explosives in complex samples

Secondary electrospray ionization-ion mobility-time of flight mass spectrometry (SESI-IM-TOFMS) was used to evaluate common household products and food ingredients for any mass or mobility responses that produced false positives for explosives. These products contained ingredients which shared the same mass and mobility drift time ranges as the analyte ions for common explosives. The results of this study showed that the vast array of compounds in these products can cause either mass or mobility false positive responses. This work also found that two ingredients caused either enhanced or reduced ionization of the target analytes. Another result showed that an IMS can provide real-time separation of ion species that impede accurate mass identifications due to overlapping isotope peak patterns. The final result of this study showed that, when mass and mobility values were used to identify an ion, no false responses were found for the target explosives. The wider implication of these results is that the possibility exists for even greater occurrences of false responses from complex mixtures found in common products. Neither IMS nor MS alone can provide 100% assurance from false responses. IMS, due to its low cost, ease of operation, rugged reliability, high sensitivity and tunable selectivity, will remain the field method of choice for the near future but, when combined with MS, can also reduce the false positive rate for explosive analyses.     

Ion mobility spectrometry as a high-throughput analytical tool in occupational pyrethroid exposure

The capabilities of ion mobility spectrometry (IMS) as a high throughput and green analytical tool in the occupational health and safety control, using pyrethroids as models has been evidenced. The method used for dermal and inhalation exposure assessment is based on the passive pyrethroid sampling using Teflon membranes, direct thermal extraction of the pyrethroids, and measurement of the vaporized analytes by IMS without reagent and solvent consumption. The IMS signatures of the studied synthetic pyrethroids under atmospheric pressure chemical ionization by investigating the formed negative ion products have been obtained. The main advantages of the proposed procedure are related to the obtained limits of detection, ranging from 0.08 to 5 ng, the simplicity of measurement, the lack of sample treatment, and therefore, solvent consumption and waste generation, and finally, the speed of analysis.     

Coupling of capillary electrophoresis with electrospray ionization multiplexing ion mobility spectrometry

In this work, ion mobility spectrometry (IMS) function as a detector and another dimension of separation was coupled with CE to achieve two‐dimensional separation. To improve the performance of hyphenated CE‐IMS instrument, electrospray ionization correlation ion mobility spectrometry is evaluated and compared with traditional signal averaging data acquisition method using tetraalkylammonium bromide compounds. The effect of various parameters on the separation including sample introduction, sheath fluid of CE and drift gas, data acquisition method of IMS were investigated. The experimental result shows that the optimal conditions are as follows: hydrodynamic sample injection method, the electrophoresis voltage is 10 kilo volts, 5 mmol/L ammonium acetate buffer solution containing 80% acetonitrile as both the background electrolyte and the electrospray ionization sheath fluid, the ESI liquid flow rate is 4.5 μL/min, the drift voltage is 10.5 kilo volts, the drift gas temperature is 383 K and the drift gas flow rate is 300 mL/min. Under the above conditions, the mixture standards of seven tetraalkylammoniums can be completely separated within 10 min both by CE and IMS. The linear range was 5–250 μg/mL, with LOD of 0.152, 0.204, 0.277, 0.382, 0.466, 0.623 and 0.892 μg/mL, respectively. Compared with traditional capillary electrophoresis detection methods, the developed CE‐ESI‐IMS method not only provide two sets of qualitative parameters including electrophoresis migration time and ion drift time, ion mobility spectrometer can also provide an additional dimension of separation and could apply to the detection ultra‐violet transparent compounds or none fluorescent compounds.     

Optimum collision energies for proteomics: The impact of ion mobility separation

Ion mobility spectrometry (IMS) is a widespread separation technique used in various research fields. It can be coupled to liquid chromatography–mass spectrometry (LC–MS/MS) methods providing an additional separation dimension. During IMS, ions are subjected to multiple collisions with buffer gas, which may cause significant ion heating. The present project addresses this phenomenon from the bottom-up proteomics point of view. We performed LC–MS/MS measurements on a cyclic ion mobility mass spectrometer with varied collision energy (CE) settings both with and without IMS. We investigated the CE dependence of identification score, using Byonic search engine, for more than 1000 tryptic peptides from HeLa digest standard. We determined the optimal CE values—giving the highest identification score—for both setups (i.e., with and without IMS). Results show that lower CE is advantageous when IMS separation is applied, by 6.3 V on average. This value belongs to the one-cycle separation configuration, and multiple cycles may supposedly have even larger impact. The effect of IMS is also reflected in the trends of optimal CE values versus m/z functions. The parameters suggested by the manufacturer were found to be almost optimal for the setup without IMS; on the other hand, they are obviously too high with IMS. Practical consideration on setting up a mass spectrometric platform hyphenated to IMS is also presented. Furthermore, the two CID (collision induced dissociation) fragmentation cells of the instrument—located before and after the IMS cell—were also compared, and we found that CE adjustment is needed when the trap cell is used for activation instead of the transfer cell. Data have been deposited in the MassIVE repository (MSV000090944).     

Detection of fuel-oxidizer explosives utilizing portable capillary electrophoresis with wipe-based sampling

Portable analytical instrumentation that can provide an alarm indication for the presence of explosives and related components is critical for the identification of explosives-based hazards and threats. Many explosives incident reports involve an inorganic oxidizer-fuel mixture which can include pyrotechnics, fireworks, flash powders, black powders, black powder substitutes, and improvised or homemade explosives. A portable CE instrument with targeted analysis of common inorganic oxidizer ions, for example, chlorate, perchlorate, and nitrate, was used here as a rapid detection platform. Unlike frequently used gas-phase separation and detection instrumentation such as ion mobility spectrometry (IMS), an automated liquid extraction mechanism is required for CE separation using acetate paper sample collection wipes. Target inorganic oxidizers were inkjet-printed onto sample wipes to investigate instrument response relative to the collected analyte spatial distribution. Overall, analyte signal intensities increased with off-center sample deposition due to improved sample extraction from wipes and no change in response was observed for varied array distributions across wipes. The system demonstrated sub 200 ng detection limits for all target analytes, with further improvement when normalizing to an internal standard.     

Ion mobility spectrometry detection for gas chromatography

The hyphenated analytical method in which ion mobility spectrometry (IMS) is coupled to gas chromatography (GC) provides a versatile alternative for the sensitive and selective detection of compounds after chromatographic separation. Providing compound selectivity by measuring unique gas phase mobilities of characteristic analyte ions, the separation and detection process of gas chromatography-ion mobility spectrometry (GC-IMS) can be divided into five individual steps: sample introduction, compound separation, ion generation, ion separation and ion detection. The significant advantage of a GC-IMS detection is that the resulting interface can be tuned to monitor drift times/ion mobilities (as a mass spectrometer (MS) can be tuned to monitor ion masses) of interest, thereby tailoring response characteristics to fit the need of a given separation problem. Because IMS separates ions based on mobilities rather than mass, selective detection among compounds of the same mass but different structures are possible. The most successful application of GC-IMS to date has been in the international space station. With the introduction of two-dimensional gas chromatography (2D-GC), and a second type of mobility detector, namely differential mobility spectrometry (DMS), GC prior to mobility measurements can now produce four-dimensional analytical information. Complex mixtures in difficult matrices can now be analyzed. This review article is intended to provide an overview of the GC-IMS/DMS technique, recent developments, significant applications, and future directions of the technique.     

Determination of terpenes in humid ambient air using ultraviolet ion mobility spectrometry

Atmospheric humidity causes the major problem using ion mobility spectrometers (IMS) under ambient conditions. Significant changes of the spectra are decreasing sensitivity as well as selectivity. Therefore, the influence of humidity on the IMS signal was investigated in case of direct introduction of the analyte into the ionisation chamber and in case of pre-separation by help of a multi-capillary column (MCC). For direct analyte introduction, a significant decrease of the total number of ions in the range of 28-42% with increasing relative humidity was found. Simultaneously additional peaks in the spectra were formed, thus complicating the identification of the analytes. In case of pre-separation of the analyte, the spectra do not change with increasing relative humidity, due to the successive appearance of the analyte and the water molecules in the ionisation chamber. Detection limits were found in the range of 5 μg/m³ (about 1 ppbv) for selected terpenes and—with pre-separation—independent on relative humidity of the analyte. Without pre-separation, detection limits are in the same range for dry air as carrier gas but in the range of 200-600 μg/m³ when relative humidity reaches 100%. Thus, MCC-UV ion mobility spectrometry is optimally capable for the detection of trace substances in ambient air (e.g. indoor air quality control, process control, odour detection) without further elaborate treatment of the carrier gas containing the analyte and independent on relative humidity.