Synthesis and characterization of amphiphilic phenylene ethynylene oligomers and their Langmuir-Blodgett films

We report the synthesis of a series of amphiphilic molecular building blocks that can be self-assembled at the air-water interface to form two- and three-dimensional nanostructures with tunable optoelectronic properties. Compression of these molecular building blocks using the Langmuir-Blodgett method gives rise to monolayer and multilayer thin films with different packing densities and electronic properties that are tunable due to varying pi-pi (hydrophobic) interactions. Depending on the noncovalent interaction between chromophores, we observe a transition toward denser packing with increasing number of phenylene ethynylene repeat units. Additionally, we use quantum-chemical simulations to help determine the excited-state electronic structure, intermolecular interactions, and packing trends. Our results demonstrate that the interplay between dipole-dipole and pi-pi interactions dominates the formation of thin films with various packing densities and determines the associated optical properties.     

Preparation and characterization of polyion-complexed Langmuir-Blodgett films containing an NLO chromophore

Polyion complexes formed by monolayers of quaternary ammonium amphiphiles containing the 4-nitro-4'-alkoxy azobenzene chromophore spread at the surface of aqueous solutions of a number of anionic polyelectrolytes were investigated. In general, pi-A isotherms were found to depend on the nature of the polyion present in the subphase, with monolayers of complexes involving polycarboxylates tending to exhibit larger limiting areas than those formed with polysulfonates or polysulfates. Monolayers of the polyion complexes can be transferred to hydrophilic solid substrates to yield Z-type LB films, although some peeling off for more than 10 layers is an impediment. X-ray reflectivity measurements indicate that relatively smooth and uniform films are obtained up to about 10 layers. Average layer thicknesses are, however, significantly smaller than extended molecular lengths, implying that the amphiphiles are strongly inclined from the surface normal. Polarized FT-IR measurements also indicate poor molecular orientation perpendicular to the surface. Preliminary SHG measurements for LB films of two systems, 12Q/CMC-Na and 12Q/PAA, confirm the presence of noncentrosymmetric out-of-plane chromophore ordering. Stable signals are observed for elevated temperatures up to 130 degrees C and for a period of 4 months at room temperature. To the best of our knowledge, this represents the first report of stable SHG in LB films of polyion complexes.     

Polymeric Langmuir-Blodgett films containing xanthene dyes

Spectral and protolytic properties of two hydrophobic rhodamine dyes and fluorescein n-decyl ester were studied in Langmuir-Blodgett films based on a polyamido acid. The possibility of weakening the concentration quenching of rhodamine dye fluorescence with a polymeric matrix was demonstrated.     

Hydrogen bond-stabilized helix formation of a m-phenylene ethynylene oligomer

[reaction: see text] Incorporation of a single hydrogen bonded beta-turn mimic in the backbone of a m-phenylene ethynylene oligomer is shown to affect the thermodynamic properties of the folding reaction. Oligomers 1 and 2 both undergo solvophobic helix formation, but hydrogen bonded oligomer 1 was found to form a more stable helix with a higher tolerance to solvent denaturation than isomeric, non-hydrogen bonded oligomer 2.     

Thermal properties and solubility of ordered aromatic polyamides containing a methyl-substituted phenylene linkage

Ordered aromatic polyamides and copolyamides were prepared by the polycondensation of terephthaloyl and isophthaloyl dichlorides with symmetrical diamines containing preformed amide linkages derived from unsymmetrical methyl—substituted aromatic diamines at low temperature. Thermal properties and solubilities of the ordered polyamides were compared with those of the corresponding random polyamides. There was little difference between thermal stabilities of the ordered polyamide and the corresponding random one, while the former was less soluble in organic solvents than the latter, depending on the extent of hydrogen bonding of the amide groups. The thermal stability of the alternating copolyamides containing both terephthaloyl and isophthaloyl groups as acid components was less than that of the corresponding homopolymers having either a terephthaloyl or an isophthaloyl group, and the solubility of the former resembled that of the corresponding ordered homopolysiophthalamides in accord with the extent of hydrogen bonding of the amide groups in both polymers.     

Electron transfer through clay monolayer films fabricated by the Langmuir-Blodgett technique

Hybrid films composed of amphiphilic molecules and clay particles were constructed by the modified Langmuir-Blodgett (LB) method. Clays used were sodium montmorillonite (denoted as mont) and synthetic smectite containing Co(II) ions in the octahedral sites (denoted as Co). Two kinds of amphiphilic molecules were used-[Ru(dC(18)bpy)(phen)2](ClO4)2 (dC(18)bpy = 4,4'-dioctadecyl-2,2'-bipyridyl and phen = 1,10-phenanthroline) (denoted as Ru) and octadecylammonium choloride (ODAH+Cl- or denoted as ODAH). Three kinds of hybrid films (denoted as Ru-mont, Ru-Co, and ODAH-Co films) were prepared by spreading an amphiphilic molecule onto an aqueous suspension of a clay. Atomic force microscopy (AFM) analyses of the films deposited on silicon wafers indicated that closely packed films were obtained at 20 ppm for all the above three cases. Cyclic voltammetry (CV) was measured on an ITO electrode modified with a hybrid film or a monolayer film of pure Ru(II) complex salt (denoted as Ru film). The Ru(II) complexes incorporated in the Ru-mont film lost their redox activity, indicating that montmorillonite layers acted as a barrier against electron transfer. In contrast, the same complexes in the Ru-Co film were electrochemically active with the simultaneous appearance of the redox peaks due to the Co(II)/Co(III) (or Co(II)/Co(IV)) couple. The results implied that electron transfer through cobalt clay layers was possible via mediation by Co(II) ions in a clay sheet. For an aqueous solution containing nitrite ions (NO2-) at pH 3.0, a large catalytic oxidation current was observed for both the electrodes modified with the Ru-mont and Ru-Co films. The results were interpreted in terms of the mechanisms that the charge separation of an incorporated Ru(II) complex took place to produce a pair of a Ru(III) complex and an electron and that the generated Ru(III) complex was reduced by a nitrite ion before it recombined with the electron.     

Lamellar multilayer hexadecylaniline-modified gold nanoparticle films deposited by the Langmuir-Blodgett technique

Organization of hexadecylaniline (HDA)-modified colloidal gold particles at the air-water interface and the formation thereafter of lamellar, multilayer films of gold nanoparticles by the Langmuir-Blodgett technique is described in this paper. Formation of HDA-capped gold nanoparticles is accomplished by a simple biphasic mixture experiment wherein the molecule hexadecylaniline present in the organic phase leads to electrostatic complexation and reduction of aqueous chloroaurate ions, capping of the gold nanoparticles thus formed and phase transfer of the now hydrophobic particles into the organic phase. Organization of gold nanoparticles at the air-water interface is followed by surface pressure—area isotherm measurements while the formation of multilayer films of the nanoparticles by the Langmuir-Blodgett technique is monitored by quartz crystal microgravimetry, UV-Vis spectroscopy, Fourier transform infrared spectroscopy and transmission electron microscopy.     

Langmuir-Blodgett films of preformed polymers containing biphenyl groups

Polymers containing liquid crystal groups have been studied previously as waveguides, and they have been deposited as spacer materials with various chromophores to form alternating films However, only a few members of this group of materials have been studied in any detail, and very little structural information has been obtained so far. Therefore, a more detailed examination of these materials as mono- and multilayers was undertaken. A new group of materials including the same mesogenic group, polymeric sulfones, was also studied. The polymers gave steep isotherms with high collapse pressures, indicating good packing of the monolayers, and could be deposited to form thick multilayers. X-ray diffraction showed that an ordered multilayer was formed, and the effects of the polymers chemical nature on the structure of the LB films are discussed. It appears that the dominant factor in monolayer structure is the nature of the polymer backbone rather than that of the liquid crystal side chains, which play a secondary role.     

Percolation conductivity in Langmuir-Blodgett multilayer films containing a long-chain TTF derivative

The room-temperature DC in-plane electrical conductivity of multilayer Langmuir-Blodgett films of the long-chain tetrathiafulvalene (TTF) derivative octadecanoyl-TTF (ODTTF), mixed with either octadecanoic acid (OA) or pentacosa-10,12-diynoic acid (PA) and doped with iodine, has been measured with a standard two-probe technique. The conductivity was found to depend strongly on the proportion of fatty acid contained in the film, and this behaviour has been compared with that predicted by classical, two-site, two-dimensional (2D) and three-dimensional percolation theory. A percolation threshold corresponding to an ODTTF content of approximately 50% was observed in both cases, in agreement with the value obtained from the 2D model. For films diluted with OA, however, the conductivity transition was smeared out, suggesting a contribution by charge transport perpendicular to the plane of the substrate. Optical microscope studies of these multilayer films have provided further evidence of a two-phase structure.     

Preparation of a vast CoFe2O4 magnetic monolayer by Langmuir-Blodgett technique

The preparation of ultrathin films of CoFe2O4 nanocrystallites is reported. TEM images of them showed 2-dimensional assembly of particles, demonstrating the uniformity of these nanocrystallites. The formation of a Langmuir monolayer of the surface coated CoFe2O4 nanocrystallites with oleate at the air/water interface and its stability were studied with pressure-area isotherm curves and Brewster Angle Microscope (BAM) images. Surface pressure vs surface area isotherms and TEM studies demonstrated that the increasing surface pressure resulted in a transition from a complex with well-separated domains of nanocrystallites to well-compressed, monoparticulate layers, and, ultimately, to multiparticulate layers.     

Preparation and characterization of mono- and multilayer films of polymerizable 1,2-polybutadiene using the Langmuir-Blodgett technique

The essence of this study is to apply the Langmuir-Blodgett (LB) technique for assembling asymmetric membranes. Accordingly, Langmuir films of a (further) polymerizable polymer, 1,2-polybutadiene (1,2-pbd), were studied and transferred onto different solid supports, such as gold, indium tin oxide (ITO), and silicon. The layers were characterized both at the air/water interface as well as on different substrates using numerous methods including cyclic voltammetry, impedance spectroscopy, spectroscopic ellipsometry, atomic force microscopy, X-ray photoelectron spectroscopy, and reflection-absorption Fourier transform infrared spectroscopy. The Langmuir films were stable at the air-water interface as long as they were not exposed to UV irradiation. The LB films formed disorganized layers, which gradually blocked the permeation of different species with increasing the number of deposited layers. The thickness was ca. 4-7 ? per layer. Irradiating the Langmuir films caused their cross-linking at the air-water interface. Furthermore, we took advantage of the reactivity of the double bond of the LB films on the solid supports and graft polymerized acrylic acid on top of the 1,2-pbd layers. This approach is the basis of the formation of an asymmetric membrane that requires different porosity on both of its sides.     

Synthesis and characterization of polymethacrylates containing conjugated oligo(phenylene ethynylene)s as side chains

In order to form suitable systems designed for resonance energy transfer, a series of monodisperse methacrylate‐based monomers containing rigid π‐conjugated oligo(phenylene ethynylenes) with different sizes of the conjugated systems ( M1 – M3 ), and therefore different optoelectronic properties, were synthesized and subsequently polymerized using the reversible addition–fragmentation chain transfer polymerization technique ( P1 – P3 ). In addition, these oligomers were also copolymerized with methyl methacrylate. The obtained polymers were characterized by ¹H NMR spectroscopy, size exclusion chromatography, and analytical ultracentrifugation. The photophysical properties of the polymers were studied by UV–vis absorption and emission spectroscopy in diluted solutions as well as in thin films and compared to the photophysics of the corresponding monomers. Thereby, changes going from monomeric to polymeric systems could be detected in fluorescence quantum yields and lifetimes pointing to energy trapping, e.g., energy transfer. Donor–acceptor copolymers containing different numbers of monomeric units within the side chain exhibit differences in the emission spectra, indicating that energy trapping in polymers is very sensitive to structural properties such as the chain length. UV–vis absorption spectroscopy as well as time‐resolved lifetime studies indicate intrapolymer and interpolymer energy transfer. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Combinatorial synthesis of oligo(phenylene ethynylene)s

The combinatorial synthesis of oligo(phenylene ethynylene) tetramers, both in solution and on solid support, is described. These products are of interest for molecular electronics applications. An iterative sequence, coupling of aryl halides to alkynes under Sonogashira conditions, was used. Five monomers functionalized with electron-donating or electron-withdrawing groups were synthesized, and used to generate a library of 25 trimers in a solution-phase based process. A library of 24 tetramers was prepared by subsequent protodesilylation and coupling with the alligator clip 4-iodo-1-thioacetylbenzene. The solution-phase based sequence was successfully adapted to a higher yielding directed split-and-pool solid-phase process, with average yields of 78–86% for each step over seven steps. A triazene linker group was used to attach the starting monomer to the polymer beads. At the completion of the solid-phase-based process, traceless cleavage of trimers from the resin was achieved by sonication of the resin in 10% HCl/THF solution. The released products were then poised for the final step in the sequence, attachment of the alligator clip.     

Large scale assembly of ordered donor-acceptor heterojunction molecular wires using the Langmuir-Blodgett technique

Unidirectionally aligned photoconductive donor-acceptor heterojunction molecular wires spanning over fifty square microns are fabricated using the Langmuir-Blodgett technique.     

Capture and detection of a quencher labeled oligonucleotide by poly(phenylene ethynylene) particles

Fluorescence quenching of poly(phenylene ethynylene) (PPE) particles by a Cy-5 labeled oligonucleotide is 2 orders of magnitude more sensitive than direct excitation of the Cy-5 fluorophore.     

pH-dependent optical properties of a poly(phenylene ethynylene) conjugated polyampholyte

A poly(phenylene ethynylene) conjugated polymer (PPE-NMe(3)(+)-COO(-)) containing tetraalkylammonium groups and carboxylate groups has been synthesized by Sonogashira coupling. Due to the presence of the strong cationic and weak anionic pendant units, the polymer undergoes a pH-induced transition from cationic polyelectrolyte to polyampholyte due to deprotonation of the carboxylic acid units in basic solution. Studies of the pH dependence of the polymers' optical properties reveal changes in absorption oscillator strength and fluorescence quantum efficiency that are triggered by the transition from cationic polyelectrolyte to polyampholyte nature. Stern-Volmer fluorescence quenching of PPE-NMe(3)(+)-COO(-) with a negatively charged quencher 1,4,5,8-naphthalenediimide-N,N-bis(methylsulfonate) (NDS) shows that the polymer fluorescence quenching is amplified at low pH where the polymer is a polycation, whereas the quenching efficiency is considerably less at high pH.     

Conformation of ionizable poly Para phenylene ethynylene in dilute solutions

The conformation of dinonyl poly para phenylene ethynylenes (PPEs) with carboxylate side chains, equilibrated in solvents of different quality have been studied using molecular dynamics simulations. PPEs are of interest because of their tunable electro‐optical properties, chemical diversity, and functionality which are essential in wide range of applications. The polymer conformation determines the conjugation length and their assembly mode and affects electro‐optical properties which are critical in current and potential uses. This study investigates the effect of carboxylate fraction on PPEs side chains on the conformation of chains in the dilute limit, in solvents of different quality. The dinonyl PPE chains are modeled atomistically, where the solvents are modeled both implicitly and explicitly. Dinonyl PPEs maintained a stretched out conformation up to a carboxylate fraction f of 0.7 in all solvents studied. The nonyl side chains are extended and oriented away from the PPE backbone in toluene and in implicit good solvent, whereas in water and implicit poor solvent, the nonyl side chains are collapsed toward the PPE backbone. Rotation around the aromatic ring is fast and no long range correlations are seen within the backbone. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 582–588     

Study of nonlinear optical properties of multilayer Langmuir-Blodgett films containing bacteriorhodopsin

Multilayer oriented Langmuir-Blodgett films of bacteriorhodopsin were prepared and their nonlinear optical properties, including second harmonic generation and photoresponse at a two phase-modulated beams mixing, were investigated. The nonlinear component of refractive index of the films was measured.