Observation of tungsten particles in vacuum arcs by laser inducedfluorescence

We have clarified the relation between the decay of tungsten ion density in the vicinity of current zero and vacuum arc mode in high current period by using a laser induced fluorescence method in tungsten vacuum arcs of 60 Hz sinusoidal current with the peak value of 3.3, 6.7, and 9.8 kA. In the case of 6.7 kA, the arc mode was the anode spot mode. Because of the generation of the anode spot, the tungsten ion density near the anode was higher than near the cathode and the density near the anode was about ten times as high as the case of 3.3 kA which was the diffuse mode. In the case of 9.8 kA, which was the intense arc mode, the density near the anode was not significantly different from the case of 6.7 kA. The density near the cathode was higher than near the anode and tungsten ions were observed till about 30 μs after current zero while they disappeared at current zero in the other cases     

Vacuum Arc Anode Phenomena

This paper briefly reviews anode phenomena in vacuum arcs, specially experimental work. It discusses, in succession, arc modes at the anode, anode temperature measurements, anode ions, transitions of the arc into various modes (principally the anode spot mode), and theoretical explanations of anode phenomena. The two most common anode modes in a vacuum arc are a low current mode where the anode is basically passive, acting only as a collector of particles emitted from the cathode, and a high current mode with a fully developed anode spot. Characteristically this anode spot has a temperature near the atmospheric boiling point of the anode material and is a copious source of vapor and energetic ions. However, other anode modes can exist. A low current vacuum arc with electrodes of readily sputterable material may emit a flux of sputtered atoms from the anode. Usually this sputtered flux will have little effect upon the vacuum arc, but in certain circumstances it could be significant. A vacuum arc doesn't always transfer directly from a low current mode to the anode spot mode. In appropriate experimental conditions, formation of an anode spot may be preceded by the formation of an anode footpoint. This footpoint is luminous, but much cooler than a true anode spot. Finally, (again in appropriate circumstances) several small anode spots may form instead of one large anode spot. With sufficient increase in arc current or arcing time these will usually combine to form a single large active spot.     

A Review of Anode Phenomena in Vacuum Arcs

This paper discusses arc modes at the anode, anode temperature measurments, anode ions, transitions of the arc into various modes (principally the anode-spot mode), and theoretical explanations of anode phenomena. A vacuum arc can exhibit five anode discharge modes: 1) a low-current mode in which the anode is basically passive, acting only as a collector of particles emitted from the cathode; 2) a second low-current mode that can occur if the electrode material is readily sputtered (a flux of sputtered atoms will be emitted by the anode); 3) a footpoint mode, characterized by the appearance of one or more luminous spots on the anode (footpoints are much cooler than the true anode spots present in the last two modes); 4) an anode-spot mode in which one large or several small anode spots are present (such spots are very luminous, have a temperature near the atmospheric boiling point of the anode material, and are a copious source of vapor and ions); and 5) an intense-arc mode where an anode spot is present, but accompanied by severe cathode erosion. The arc voltage is relatively low and quiet in the two low-current modes and the intense-arc mode. It is usually high and noisy in the footpoint mode, and it can be either in the anode-spot mode. Anode erosion is low, indeed negative, in the two low-current modes, and it is low to moderate in the footpoint mode. Severe anode erosion occurs in both the anode-spot and intense-arc modes.     

Ion flux from the cathode region of a vacuum arc

The properties of the ion flux generated in a vacuum arc are reviewed. The structure and distribution of mass erosion from individual cathode spots and the characteristics of current carriers from the cathode region at moderate arc currents are described. An appreciable ion flux (~10% of the total arc current) is emitted from the cathode of a vacuum arc. This ion flux is strongly peaked in the direction of the anode, although some ion flux may be seen even at angles below the plane of the cathode surface. The observed spatial distribution of the ion flux is expressed quite well as an exponential function of the solid angle. The ion flux is quite energetic, with average ion potentials much larger than the arc voltage, and generally contains a considerable fraction of multiply charged ions. The average ion potential and ion multiplicity increase significantly for cathode materials with higher arc voltages but decrease with increasing arc current for a particular material. The main theories concerning ion acceleration in cathode spots are the potential hump theory and the gas dynamic theory. Experimental data indicate that these theories serve reasonably well when used to predict the mean values of the charge state, ion potential, and ion energies for the ion flux, but are quite insufficient when compared with the results for the potentials and energies of individual ions     

Numerical simulation of anode heat transfer of nitrogen arc utilizing two-temperature chemical non-equilibrium model

A detailed understanding of anode heat transfer is important for the optimization of arc processing technology. In this paper, a two-temperature chemical non-equilibrium model considering the collisionless space charge sheath is developed to investigate the anode heat transfer of nitrogen free-burning arc. The temperature, total heat flux and different heat flux components are analyzed in detail under different arc currents and anode materials. It is found that the arc current can affect the parameter distributions of anode region by changing plasma characteristics in arc column. As the arc current increases from 100 A to 200 A, the total anode heat flux increases, however, the maximum electron condensation heat flux decreases due to the arc expansion. The anode materials have a significant effect on the temperature and heat flux distributions in the anode region. The total heat flux on thoriated tungsten anode is lower than that on copper anode, while the maximum temperature is higher. The power transferred to thoriated tungsten anode, ranked in descending order, is heat flux from heavy-species, electron condensation heat, heat flux from electrons and ion recombination heat. However, the electron condensation heat makes the largest contribution for power transferred to copper anode.     

A novel anode attachment mode in argon-helium free-burning arcs at atmospheric pressure

An argon-helium free-burning arc that operates on a graphite anode is investigated. Images of the arc and anode attachment under different arc currents and different helium ratios are exhibited. Experimental results show that both the arc and anode attachment are characterized by demixing. Moreover, an annular dark region surrounding the anode center is observed in the anode attachment region under the conditions of a higher arc current and a higher helium ratio, which is similar to the self-organized anode attachment mode in glow discharges. Preliminary analysis indicates that the arc demixing, the thermophysical properties of the mixture gas, and the carbon vapors from anode evaporation contribute to the formation of this novel anode attachment mode.     

A Review of Anode Phenomena in Vacuum Arcs

This paper discusses are modes at the anode, experimental results pertinent to anode phenomena, and theoretical explanations of anode phenomena. A vacuum are can exhibit five anode discharge modes: (1) a low current mode in which the anode is basically passive, acting only as a collector of particles emitted from the cathode; (2) a second low current mode that can occur if the electrode material is readily sputtered (a flux of sputtered atoms will be emitted by the anode); (3) a footpoint mode, characterized by the appearance of one or more small luminous spots on the anode (footpoints are generally much cooler than the true anode spots present in the last two modes); (4) an anode spot mode in which one large or several small anode spots are present (such spots are very luminous, have a temperature near the atmospheric boiling point of the anode material, and are a copious source of vapor and ions); and (5) an intense are mode where an anode spot is present, but accompanied by severe cathode erosion. The are voltage is relatively low and quiet in the two low current modes and the intense are mode. It is usually high and noisy in the footpoint mode, and it can be either in the anode spot mode. Anode erosion is low, indeed negative, in the two low current modes, and it is low to moderate in the footpoint mode. Severe anode erosion occurs in both the anode spot and intense are modes. The dominant mechanism controlling the formation of an anode spot appears to depend upon the electrode geometry, the electrode material, and the current waveform of the particular vacuum are being considered. In specific experimental conditions, either magnetic constriction in the gap plasma, or gross anode melting, or local anode evaporation can trigger the transition. However, the most probable explanation of anode spot formation is a combination theory, which considers magnetic constriction in the plasma together with the fluxes of material from the anode and cathode as well as the thermal, electrical, and geometric effects of the anode in analyzing the behavior of the anode and the nearby plasma.     

Experimental investigations of the currents collected by metalshields in high-current vacuum arcs

This paper presents experimental results of currents collected on the three-element condensation shield connected to the cathode potential in high-current vacuum arcs. The arc current had 900 Hz, 150 Hz, or 50 Hz half-cycle sinusoidal shapes and was conducted between the CuCr40 contacts with a diameter of 50 mm (cathode) and 30 mm (anode) spaced 10 mm apart. Most of the measurements were made for the current of 900 Hz with peak values up to 9 kA. Arc voltage, floating shield potential, and distribution of shield currents were measured. It was found that the current collected by the shield and also the arc voltage and floating shield potential are greater for higher frequency currents, and that they are affected by the arc mode. Considerable shield current is observed during a high-amplitude (HA) oscillation sequence of arc voltage while its mean value is increased. For 900-Hz arcs at the 9-kA peak value (I_am), the ratio of shield current (i_s) to an instantaneous value of arc current (i_a) reaches even 40% near I_am value. In the initial half-cycle period (before the initiation of high-voltage oscillation), the ratio of i_s/i_a increases with i_a and current frequency. A close relationship was found between arc voltage and current distribution on a three-element shield     

Operational characteristics of a plasma cathode with a grid stabilization in a two-stage ion source

The discharge characteristics and the parameters of the cathode plasma in a two-stage ion source with a grid plasma cathode and a magnetic trap in the anode region are investigated. It is shown that an increase in the gas pressure and the accompanying increase in the reverse ion current in the bipolar diode between the cathode and anode plasmas lead to an increase in the cathode plasma potential and a transition of the cathode into the regime of electron emission from the open plasma boundary. The dependence of the ion current extracted from the anode plasma on the area of the exit aperture of the hollow cathode and the mesh size of the grid plasma cathode is explained. The conditions at which the ion emission current from the anode plasma is maximum are determined. The potential difference at the bipolar diode is measured by using the probe method. It is shown that, when the gas pressures reaches a critical value determined by the mesh size of the grid plasma cathode, the discharge passes into a contracted operating mode, in which the ion current extracted from the anode plasma decreases severalfold.     

Vacuum Arc Anode Phenomena

This paper presents a brief review of anode phenomena in vacuum arcs. It discusses in succession the transition of the arc into the anode spot mode; the temperature of the anode before, during, and after formation of an anode spot; and anode ions. Characteristically the anode spot has a temperature of the order of the atmospheric boiling point of the anode material and is a copious source of vapor and energetic ions. The dominant mechanism controlling the transition of the vacuum arc into the anode spot mode appears to depend upon the electrode geometry, the electrode material, and the current waveform of the particular vacuum arc being considered. Either magnetic constriction in the gap plasma or gross anode melting can trigger the transition, indeed a combination of the two is a common cause of anode spot formation.     

Discharge Modes at the Anode of a Vacuum Arc

Five possible discharge modes can exist at the anode of a vacuum arc. The two most common anode modes are a low current mode, where the anode is basically inert; and a high current mode with a fully developed anode spot. This anode spot is very bright, has a temperature near the boiling point of the anode material, and is a copious source of vapor and energetic ions. Three additional anode modes can occur in appropriate circumstances. A low current vacuum arc with electrodes of readily sputterable material will emit a flux of sputtered atoms from the anode. At intermediate currents, an anode footpoint can form. This footpoint is luminous, but much cooler than a true anode spot. Finally, a high current mode can exist where several small anode spots are present instead of a single large anode spot.     

Anode jet in a high-current vacuum arc

A stable intense jet with a clear-cut bright sheath has been detected on the anode of a 10-ms-long high-current vacuum arc with a current amplitude of 15 kA. The jet is adjacent to the hot spot of a molten metal on the anode surface. The primary light of the jet is emitted by neutrals. The sheath of the jet is surrounded by an ion-induced diffuse glow. The anode jet arises from interaction between the cathode and anode plasmas. Because of this, the size of the jet inversely depends on the current of the arc and the jet becomes observable only by the end of the current pulse. This object (anode jet with a bright sheath) is well reproducible when the arc is initiated between copper-chromium electrodes. In the case of pure copper electrodes, such objects occur randomly and appear at long projections of the molten metal, where heat release is hampered, and at large drops moving in the interelectrode gap. This means that the anode evaporation intensity is crucial for the appearance of bright-sheath jets.     

Anode-Spot Formation and Motion of Vacuum Arcs

This paper reports about experimental investigations on high-current vacuum-arc phenomena, especially anode-spot formation, arc states, and motion. The presented work was stimulated by lack of information about the transition process from the diffuse low-current mode to the high-current mode characterized by anode spot(s). Optoelectronic measurements, streak photographs, high-speed movies, and correlated arc voltage/current records yielded remarkable results on power-frequency vacuum arcs. Three different high-current vacuum arc modes can be observed beyond a certain threshold current. Which mode appears depends mainly on the momentary electrode distance. The modes are characterized by different anode-spot behavior and interelectrode phenomena. The transition between different arc modes is continuous. The arc modes observed on ring electrodes producing a magnetic blast field are the same as those appearing on butt-type electrodes. Anode-spot formation is preceded by congregations of cathode spots and may be initiated by thermal overload of the anode surface opposite to these cathode-spot clusters.     

Mechanisms of anode power deposition in a low pressure free burningarc

Anode power deposition is a dominant power loss mechanism for arcjets and magnetoplasmadynamic (MPD) thrusters. In this study, a free burning arc experiment was operated at pressures and current densities similar to those in arcjets and MPD thrusters in an attempt to identify the physics controlling this loss mechanism. Use of a free burning arc allowed for the isolation of independent variables controlling anode power deposition and provided a convenient and flexible way to cover a broad range of currents, anode surface pressures, and applied magnetic field strengths and orientations using an argon gas. Test results showed that anode power deposition decreased with increasing anode surface pressure up to 6.7 Pa and then became insensitive to pressure. Anode power increased with increasing arc current, while the electron number density near the anode surface increased linearly. Anode power also increased with increasing applied magnetic field strength due to an increasing anode fall voltage. Applied magnetic field orientation had an effect only at high currents and low anode surface pressures, where anode power decreased when applied-field lines intercepted the anode surface. The results demonstrated that anode power deposition was dominated by the kinetic energy of the current-carrying electrons acquired over the anode fall region. Furthermore, the results showed that anode power deposition can be reduced by operating at increased anode pressures, reduced arc currents, anode current densities, and applied magnetic field strengths, and with magnetic field lines intercepting the anode     

Ion Flux from the Cathode Region of a Vacuum Arc

This paper reviews the properties of the cathode ion flux generated in the vacuum arc. The structure and distribution of mass erosion from individual cathode spots and the characteristics of current carriers from the cathode region at moderate arc currents are described. An appreciable ion flux (～10% of total arc current) is emitted from the cathode of a vacuum arc. This ion flux is strongly peaked in the direction of the anode, though some ion flux may be seen even at angles below the plane of the cathode surface. The observed spatial distribution of the ion flux is expressed quite well as an exponential function of solid angle. The ion flux is quite energetic, with average ion potentials much larger than the arc voltage, and generally contains a considerable fraction of multiply-charged ions. The average ion potential and ion multiplicity increase significantly for cathode materials with higher arc voltages, but decrease with increasing arc current for a particular material. The main theories concerning ion acceleration in cathode spots are the potential hump theory (PH), which assumes that all ions are created at the same potential, and the gas dynamic theory (GD), which assumes that all ions are created with the same flow velocity. Experimental data on the potentials and energies of individual ions indicates that these theories in their original forms are not quite correct, however extensions or modifications of the PH and GD theories seem very likely to be able to predict correct values for the charge states, potentials, and energies of individual ions.     

Experimental Investigation of Anode Activities in High-Current Vacuum Arcs

It is well known that the melting of electrodes (mainly anode melting) in vacuum arc can increase the metal vapor density around current zero and even lead to interruption failure. In order to clarify the anode activities and their influence on arc appearance and interruption capacity, series experiments of cup-shaped axial magnetic field copper electrodes were conducted. Obvious anode melting was detected; the liquid copper flowed on the contact plate of anode and formed a clockwise swirl flow. The appearance of anode melting is likely to correlate to the transition of arc mode from high-current diffuse mode to high-current diffuse column mode. The melting of anode was severer than cathode and was influenced by the distribution of cathode spots. Various kinds of copper particles at macroscopic level can be seen in arc column. Even at the interruption limit, the majority of melted copper of anode sputtered out of gap in form of liquid droplets or was pressed into the cup of anode, the copper vapor evaporated into arc column only accounted for a few portion and no obvious anode jets was found due to large plasma pressure in arc column.      

Simulation of transition from Townsend mode to glow discharge mode in a helium dielectric barrier discharge at atmospheric pressure

The dielectric barrier discharge characteristics in helium at atmospheric pressure are simulated based on a one-dimensional fluid model. Under some discharge conditions, the results show that one discharge pulse per half voltage cycle usually appears when the amplitude of external voltage is low, while a glow-like discharge occurs at high voltage. For the one discharge pulse per half voltage cycle, the maximum of electron density appears near the anode at the beginning of the discharge, which corresponds to a Townsend discharge mode. The maxima of the electron density and the intensity of electric field appear in the vicinity of the cathode when the discharge current increases to some extent, which indicates the formation of a cathode-fall region. Therefore, the discharge has a transition from the Townsend mode to the glow discharge mode during one discharge pulse, which is consistent with previous experimental results.     

含氢电极真空弧放电等离子体时空分布特性研究

真空弧离子源在真空镀膜、材料表面改性、真空大电流开关、加速器离子注入等领域有广泛应用,目前国内外对真空弧放电等离子体的研究主要针对纯金属或合金电极,对含氢电极的研究和公开报道较少.本文利用高时空分辨的四分幅图像诊断系统,结合氢和钛原子特征线单色器件,研究了含氢钛电极的真空弧微秒级脉冲放电等离子体的轴向和径向时空分布特性.研究表明:在真空击穿阶段,阳极区域发光更为明显,阳极电极解吸附释放的氢原子是引发击穿的主要放电介质;在真空弧阶段,阴极-绝缘-真空三结合点处产生圆锥状阴极斑,喷射出大量的等离子体以维持弧放电,同时电极内壁非阴极斑区域也有少量等离子体产生,等离子体中H原子的轴向和径向空间分布均比Ti原子均匀.     

壁面二次电子发射对霍尔推力器放电通道绝缘壁面双鞘特性的影响

为进一步揭示霍尔推力器放电通道绝缘壁面鞘层的特性, 利用考虑了壁面二次电子分布函数的一维稳态流体鞘层模型, 研究了壁面二次电子发射对近壁双鞘特性的影响. 分析结果表明, 由于壁面发射的二次电子对近壁鞘层中的电子密度有增加作用, 存在一个临界二次电子发射系数σ_dc使得: 当σ≤σ_dc时, 鞘层为单层的正离子鞘结构; 当σ>σ_dc时, 鞘层表现为双层的正离子鞘和电子鞘相连结构, 连接点对应于垂直于壁面方向上电势分布的拐点. 然而, 当σ进一步增大到0.999时, 鞘层转变为三层的正离子鞘-电子鞘-正离子鞘交替结构. 数值结果表明: 随着σ的增加, 电子鞘与离子鞘的连接点向远离壁面的方向移动, 电子鞘的厚度逐渐增加; 随着壁面出射电子能量系数a的增加, 近壁区鞘层的厚度也逐渐增加. 关键词： 霍尔推力器 双鞘 壁面二次电子发射     

Residence time of metal ions generated from microsecond vacuum arcs

Vacuum gaps of 1 mm with lead or copper cathode are fired by a 13 μs duration sinusoidal arc or a 10 μs duration exponentially-decaying arc, and time-of-flight (TOF) ion measurements are made at variable times after the arc ignition. At the lead cathode, Pb⁺ and Pb⁺⁺ ions are generated and the upper limit on the times for Pb⁺ ion detection are 48 μs and 46 μs from the arc ignition for the sinusoidal and exponential arcs, respectively. At the copper cathode, Cu⁺, Cu⁺⁺, and Cu⁺⁺⁺ ions are generated and detected within 15 μs and 13 μs from the arc ignition for the sinusoidal and exponential arcs, respectively. The residence time of the Pb⁺ ions in the ion acceleration region is approximately 35 μs, regardless of the waveform of the arc current. The residence time of the copper ions, described by the time constant of the time-of-flight ion current delay characteristics, is 3 μs