Kinetic-coulometric determination of mercury in biological samples

A simple approximate calculation method is given which permits determina-tion of the maximal scan rates of potential allowable for distortion-free recording of current-voltage curves with X-Y recorders. For the calculations only the response time of the recorder, the wave shape and the scan rate of potential need be known. Stationary mercury electrodes and rapid polarography with a dropping mercury electrode at controlled drop times were examined. Electroanalytical implications are discussed, with particular emphasis on the rapid a.c. polarographic method with short controlled drop times and on stationary-electrode fundamental and second harmonic a.c. voltammetry. Theoretically and experimentally it has been shown that an X-Y recorder with 0.5–1.0-s response time can be used for scan rates up to about (50/nt') mV s^-1 with a.c. techniques and about (100/nt') mV s^-1 with d.c. polarography (t'= response time of recorder, n = number of electrons).     

Simultaneous Voltammetric Determination of Lead and Tin by Adsorptive Differential Pulse Stripping Method and Orthogonal Signal Correction‐Partial Least Squares in Water Samples

An adsorptive differential pulse stripping method for the simultaneous determination of lead and tin is proposed. The procedure involves an adsorptive accumulation of lead and tin on a hanging mercury drop electrode (HMDE), followed by oxidation of adsorbed lead and tin by voltammetric scan using differential pulse modulation. The optimum experimental conditions are: 0.2 mol L^?1 HNO₃, accumulation potential of ?900 mV versus Ag/AgCl, accumulation time of 200 s, scan rate of 20 mV s^?1 and pulse height of 80 mV. Lead and tin peak currents were observed in the same potential region at about ?400 mV. The simultaneous determination of lead and tin by using voltammetry is a difficult problem in analytical chemistry, due to voltammogram interferences. The resolution of a mixture of lead and tin by the application of orthogonal signal correction‐partial least squares (OSC‐PLS) was performed. The linear dynamic ranges were 0.003‐0.35 and 0.008‐0.50 μg mL^?1 and detection limits were land 3 ng mL^?1 for lead and tin, respectively. The RMSEP for lead and tin with OSC and without OSC were 2.8737, 6.0557 and 8.0941, 9.5151, respectively. The capability of the method for the analysis of real samples was evaluated by the determination of lead and tin in water samples with satisfactory results.     

Palladium-catalyzed reaction of nucleophiles with diacetates of allylic 1,1-diols

The reactions of allylic 1,1-diol diacetates (I) with carbanions under the catalysis of Pd(PPh₃)₄ were studied. Sodium diethyl malonate reacted with I to form an abnormal product resulting from the attack of the diethyl malonate carbanion on the carbonyl carbon of the acetoxy group, while sodium diethyl acetylmalonate gave the normal reaction products with high regioselectivity. The mechanisms of these reactions are discussed.     

Polarographic Behaviour of Trazodone

Abstract

Trazodone, which cannot be electrochemically reduced at the dropping mercury electrode, exhibits catalytic proton reduction waves as shown by the strong modifications occuring with variations of pH, concentration, nature of the buffer, ionic strength and presence of organic solvent. The catalytic process is developing three successive waves with rising pH or concentration, depending on the protonation rate or the adsorbed state. The influence of sodium ions indicates a decrease of sorbtivity with the proton concentration. The strong surface character of the wave observed in very acidic media decreases gradually on behalf of a more pronounced bulk character with increasing pH. The wave recorded in neutral media is of analytical interest, a linear calibration curve being plotted in the 2.10^?6 M to 1.10^?3 M concentration range.     

Photoreaction of Ketoprofen with Tryptophan and Tyrosine in Phosphate Buffer Solution

Reaction of excited ketoprofen (KP) with tryptophan (Trp) and tyrosine (Tyr) in a phosphate buffer solution was studied by the transient absorption spectroscopy. Both amino acids, which would interact with KP in bovine serum albumin [Monti, S. [2009] Phys. Chem. Chem. Phys., 11, 9104–9113], accelerated the proton transfer reaction to yield 3‐ethylbenzophenone ketyl biradical (EBPH) from KP carbanion, which was produced by photoexcitation of KP^? through decarboxylation. By means of the actinometry method with benzophenone, the reaction quantum yield was successfully estimated to be fairly large, and Trp, Tyr, DOPA and 4‐methylphenol were found to be a good proton donor for the carbanion. The formation rate constants of EBPH by the amino acids (k_r) were also determined to be (2.7 ± 0.1) × 10⁹ M^?1s^?1 for Trp and (7.8 ± 0.4) × 10⁸ M^?1s^?1 for Tyr, which were larger than those by basic amino acids and dipeptides reported. The reason for the highly efficient proton transfer reaction with Trp and Tyr would be explained by difference of the activation energy for the reaction. These results suggest that the proton transfer should be a key process for an initial photoreaction of KP with a protein, causing photosensitization in vivo.     

Determination of Cysteine in the Presence of Copper in Diluted Alkaline Electrolyte by Adsorptive Stripping Voltammetry at the Mercury Film Electrode

Abstract

A stripping method for the determination of cysteine in the presence of copper at the submicromolar concentration levels is described. The method is based on controlled adsorptive accumulation of cysteine at mercury film electrode followed by linear cyclic voltammetry scan measurement of the surface species. Optimum experimental conditions were found to be the use of a 1×10^?3 M NaOH solution, an accumulation potential of ?0.50 V and a scan rate of 200 mV. s^?1. The response of cysteine is linear over the concentration range 0.04–0.20 ppm. For an accumulation time of 15 minutes, the detection limit was found to be 0.9 ppb (7.4×10^?9 M). The more convenient relation to measuring the cysteine in presence of metals, and others amino acids were also investigated. The utility of the method is demonstrated by presence of casein and ATP.     

Mechanism of electrodimerization of retinal and cinnamaldehyde

Electrochemical reduction of either cinnamaldehyde or retinal in acetonitrile containing 0.5 M. TBAP and water or phenol leads to a mixture of dimeric products. However, electroreduction of either of these aldehydes in the presence of the carbon acid, diethyl malonate, leads to increased yield of pinacol formation. The mechanism of these electrodimerization reactions has been discerned using cyclic voltammetry-variations in peak potential as a function of scan rate, proton donor concentration and concentration of aldehyde have been compared to published diagnostic criteria. Retinal and cinnamaldehyde form dimeric products in a radical-radical coupling pathway. The major mechanistic feature that correlates with product distribution is the association (solvation) of oxygen acids, phenol and water with the radical anion. In contrast, diethyl malonate reacts with the radical anion of either cinnamaldehyde or retinal by a direct proton transfer.     

Stripping Voltammetry of Mercury(II) with a Chemically Modified Carbon Paste Electrode Containing Silica Gel Functionalized with 2,5‐Dimercapto‐1,3,4‐thiadiazole

The accumulation voltammetry of mercury(II) was investigated at a carbon paste electrode chemically modified with silica gel functionalized with 2,5‐dimercapto‐1,3,4‐thiadiazole (DTTPSG‐CPE). The repetitive cyclic voltammogram of mercury(II) solution in the potential range ?0.2 to +0.8 V (vs. Ag/AgCl), (0.02 mol L^?1 KNO₃ ; v=20 mV s^?1) show two peaks one at about 0.0 V and other at 0.31 V. However, the cathodic wave peak, around 0.0 V, is irregular and changes its form in each cycle. This peak at about 0.0 V is the reduction current for mercury(II) accumulated in the DTTPSG‐CPE. The anodic wave peak at 0.31 V is well‐defined and does not change during the cycles. The resultant material was characterized by cyclic and differential pulse anodic stripping voltammetry performed with the electrode in differents supporting electrolytes. The mercury response was evaluated with respect to pH, electrode composition, preconcentration time, mercury concentration, “cleaning” solution, possible interferences and other variables. The precision for six determinations (n=6) of 0.05 and 0.20 mg L^?1 Hg(II) was 2.8 and 2.2% (relative standard deviation), respectively. The method was satisfactory and used to determine the concentration of mercury(II) in natural waters contaminated by this metal.     

Square Wave Adsorptive Stripping Voltammetry Determination of Chlorpyriphos in Irrigation Agricultural Water

This work describes the electroanalytical determination of Chlorpyriphos pesticide in natural waters using hanging mercury drop electrode allied to square wave adsorptive cathodic stripping voltammetry. The best responses were obtained in Britton?Robinson buffer solutions at pH 2.0, using a frequency of 100 s^–1, a scan increment of 5 mV, a square wave amplitude of 25 mV and an accumulation potential of–0.4 V during 60 s. Therefore, voltammetric responses showed the presence of one well-defined and irreversible reduction peak, at–1.08 V vs. Ag/AgCl/KCl 1.0 M, which involves two electrons in the reduction of carbon?nitrogen bond in the N-heterocyclic system with the participation of protonation equilibrium preceding the electron transfer reaction. Analytical curves were constructed and compared to similar curves performed by gas chromatograph coupled to a selective nitrogen?phosphorus detector, which demonstrates that the proposed methodology is suitable for determining contamination by Chlorpyriphos in complex samples.     

Adsorptive Stripping Voltammetric Determination of Ultra Trace of Zinc and Lead with Carbidopa as Complexing Agent in Food and Water Samples

In the present work, the cathodic stripping voltammetric methodology using a hanging mercury drop electrode was described for simultaneous determination of lead and zinc in different real samples. The method is based on adsorption of metal ions on mercury electrode using carbidopa as a suitable complexing agent. The potential was scanned to the negative direction and the differential pulse stripping voltammograms were recorded. Optimal conditions were found to be: accumulation time; 70 s, accumulation potential; 50 mV versus Ag/AgCl, scan rate; 40 mV s^?1, supporting electrolyte; 0.01 M ammonia buffer at pH 8.5, and concentration of carbidopa; 8.0 μM. The relationship between the peak current versus concentration was linear over the range of 0.1–210 and 0.2–170 nM for lead and zinc, respectively. The detection limits are 0.09 and 0.15 nM for lead and zinc ions respectively. The relative standard deviations at a concentration level of 70 nM of both metal ions are found 1.08 and 1.24% for lead and zinc ions respectively.     

DNA Determination in the Presence of Copper in Diluted Alkaline Electrolyte by Adsorptive Stripping Voltammetry at the Mercury Film Electrode

A stripping method for the determination of single‐stranded DNA in presence of copper at the submicromolar concentration levels is described. The method is based on controlled adsorptive accumulation of adenine (from acid‐treated DNA) at thin‐film mercury electrode followed by linear scan voltammetry measurement of the surface species. Optimum experimental conditions were found to be the use of a 5.0×10^?3 M NaOH solution, an accumulation potential of ?0.40 V and a scan rate of 200 mV s^?1. The response of adenine–copper is linear over the concentration range 50–250 ppb. For an accumulation time of 15 minutes, the detection limit was found to be 4 ppb. The more convenient relation to measuring the ssDNA in presence of metals and nitrogenated bases were also investigated. The utility of the method is demonstrated by the presence of adenosine‐triphosphate (ATP) and amino acids.     

Electrocatalysis via Direct Electrochemistry of Myoglobin Immobilized on Colloidal Gold Nanoparticles

The direct electron transfer between immobilized myoglobin (Mb) and colloidal gold modified carbon paste electrode was studied. The Mb immobilized on the colloidal gold nanoparticles displayed a pair of redox peaks in 0.1 M pH 7.0 PBS with a formal potential of –(0.108 ± 0.002) V (vs. NHE). The response showed a surface‐controlled electrode process with an electron transfer rate constant of (26.7 ± 3.7) s ^?1 at scan rates from 10 to 100 mV s^?1 and a diffusion‐controlled process involving the diffusion of proton at scan rates more than 100 mV s^?1. The immobilized Mb maintained its activity and could electrocatalyze the reduction of both hydrogen peroxide and nitrite. Thus, the novel renewable reagentless sensors for hydrogen peroxide and nitrite were developed, respectively. The activity of Mb with respect to the pseudo peroxidase with a K_M^app value of 0.65 mM could respond linearly to hydrogen peroxide concentration from 4.6 to 28 μM. The sensor exhibited a fast amperometric response to NO₂^? reduction and reached 93% of steady‐state current within 5 s. The linear range for NO₂^? determination was from 8.0 to 112 μM with a detection limit of 0.7 μM at 3σ.     

Ultratrace Xanthine Determination in Diluted Alkaline Electrolyte by Adsorptive Stripping Voltammetry at the Mercury Film Electrode

Abstract

A stripping method for the determination of xanthine at the submicromolar concentration level is described. The method is based on controlled adsorptive accumulation of xanthine at a thin-film mercury electrode followed by a linear scan voltammetry measurement of the surface species. Optimum experimental conditions were found to be the use of a 5.0 × 10^?3 M NaOH solution, an accumulation potential of 0.00 V, and a scan rate of 20 mV s^?1. The response of xanthine is linear over the concentration range 20–140 ppb. For an accumulation time of 30 min, the detection limit was found to be 36 ppt (2.3 × 10^?10 M). The more convenient relations for measuring xanthine in the presence of the metals, hypoxanthine, amino acids, and other nitrogenated bases were also investigated. The utility of the method is demonstrated by the presence of xanthine in adenosine-5′-triphosphate or DNA.     

Square wave voltammetric determination of diafenthiuron and its application to water,soil and insecticide formulation

A square wave cathodic stripping voltammetric (SWCSV) method has been developed for the determination of insecticide diafenthiuron. The procedure is based on controlled accumulation of the insecticide on a static hanging mercury drop electrode (SHMDE) at 0.00?mV (vs. Ag/AgCl) in Britton-Robinson buffer solution (pH 7.0). The insoluble mercury compound was reduced at ?510?mV during the cathodic potential scan. The peak currents were linearly related to insecticide concentration between 30.4 and 3200?µg?L^?1 . The detection and quantification limit were 9.1?µg?L^?1 and 30.4?µg?L^?1, respectively. The proposed analytical procedure was applied to natural water and soil samples. The method was extended to direct determination of diafenthiuron in insecticide formulation Polo® 50 WP and average content of 50.3?±?1.7 (m/m) at 90% confidence level, in close agreement with the 50.0% quoted by the manufacturer. HPLC comparison method indicated that accuracy was in agreement with that obtained by the proposed method.     

Imprinted Polymer – Modified Hanging Mercury Drop Electrode for Differential Pulse Adsorptive Stripping Voltammetric Analysis of a Diquat Herbicide

An imprinted polymer modified hanging mercury drop electrode (HMDE) in Model 303A system in conjunction with a PAR Model 264A Polarographic Analyzer/Stripping Voltammeter has been used for the selective analysis of a diquat herbicide viz., 5,6‐dihydropyrazino[1,2,3,4‐[lmn]‐1,10‐phenanthrolinium dichlorides in differential pulse cathodic stripping voltammetry mode. Complex aqueous samples (drinking water and agricultural soil suspension), spiked with a diquat herbicide, were directly analyzed by the adsorptive accumulation of the analyte over the working electrode (accumulation potential ?0.8 V (vs. Ag/AgCl), accumulation time 120 s, pH 7.0, supporting electrolyte 0.1 M KCl, scan rate 10 mV s^?1, pulse amplitude 25 mV). The limit of detection for diquat herbicide was found to be 0.34 nmol L^?1 (0.1 ppb, RSD 2%, S/N=2).     

Total and free charge densities on mercury coated with self-assembled phosphatidylcholine and octadecanethiol monolayers and octadecanethiol/phosphatidylcholine bilayers

The thermodynamic ‘total’ charge density is the charge to be supplied to the electrode to keep the applied potential constant when the electrode surface is increased by unity, while the extrathermodynamic ‘free’ charge density is the charge actually experienced by the diffuse layer ions. The total charge density at dioleoylphosphatidylcholine (DOPC) and octadecanethiol (ODT) monolayers and mixed ODT/DOPC bilayers self-assembled on mercury from aqueous solutions was determined from chronocoulometric single potential steps to a final potential negative enough to cause complete desorption of the film. The effect of different alkali metal ions and of tetramethylammonium on DOPC desorption was examined. The total charge for ODT monolayers and ODT/DOPC bilayers, +56±3 μC cm⁻², agrees with the value obtained by integration of the current under the reductive desorption voltammetric peaks, only provided the scan rate is higher than 100 mV s⁻¹. An approximate model of the interface of the ODT-coated electrode, which accounts for partial charge transfer from sulfur to mercury and for the degree of dissociation of the sulfhydryl group upon self-assembly, was employed to estimate the free charge density.     

Electrochemical behavior of decyl mercuric halides at mercury cathodes in dimethylformamide

Polarograms for decyl mercuric halides in dimethylformamide containing tetraalkylammonium perchlorates exhibit two waves. When large-scale electrolyses of decyl mercuric halides are performed at potentials corresponding to the first polarographic wave, the couldometric n value is unity and didecylmercury is obtained in quantitative yield; electrolyses carried out at potentials on the plateau of the second polarographic wave afford only decane and the n value is essentially 2. Double-potential-step chronocoulometry and staircase voltammetry indicate that, at potentials corresponding to the first polarographic wave, the decyl mercuric halide (which is itself adsorbed onto mercury to the extent of less than a monolayer) undergoes reversible one-electron reduction to adsorbed decyl mercury radicals and to adsorbed decyl mercury radical “polymer”; the adsorbed radicals have a lifetime of approximately 10^?3s and disproportionate into didecylmercury and elemental mercury. In the presence of electrolytically released halide ion, the adsorbed radicals are reoxidized to the decyl mercuric halide; alternately, the adsorbed species are reoxidized to decyl mercury cations at a potential approximately 600 mV more positive than that required for reoxidation to the decyl mercuric halide. At potentials corresponding to the second polarographic wave, reduction of decyl mercuric halides is an irreversible process producing decyl carbanions which are protonated by traces of water in the solvent to give decane.     

Adsorptive Stripping Voltammetry of 9‐Phenanthrol in the Presence of Copper at the Static Mercury Drop Electrode—Basis for Quantitative Determination of PAH Metabolite in Biological Materials

Abstract

The electrochemical behavior of 9‐phenanthrol in the presence of copper (II) at a static mercury drop electrode was investigated to provide the basis for development of an inexpensive, sensitive, and reliable method for determination of polycyclic aromatic hydrocarbon (PAH) metabolites in biological matrices. Optimum experimental conditions for analytical applications were obtained in 0.005 M NaOH solution using an accumulation potential of ?0.25 V, a scan rate of 5 mV. s^?1, a pulse height of 25 mV, and a differential pulse scan mode. The response of 9‐phenanthrol is linear over the concentration range 1.0–12.0 ppb. For an accumulation time of 5 minutes, the detection limit was found to be 0.2 ppb (1.03×10^?9 M). The more convenient relation to measure the 9‐phenanthrol in the presence of copper and other metals was also investigated. The utility of the method was demonstrated by the presence of 9‐phenanthrol in samples of sea water and human urine. Cyclic voltammetry was used to characterize the interfacial and redox behavior.     

Voltammetric Behavior of Arsenic(III) in the Presence of Sodium Diethyl Dithiocarbamate and Its Determination in Water and Highly Saline Samples by Adsorptive Stripping Voltammetry

This paper describes the voltammetric behavior of As(III) at the hanging mercury drop electrode (HMDE) in the presence of sodium diethyl dithiocarbamate (SDDC) and a new voltammetric method for the determination of As(III) at trace levels. The method is based on the adsorptive deposition of a As(III) complex with SDDC at ?0.45 V (vs. Ag/AgCl) on the HMDE in acidic medium of 0.01 mol L^?1 HCl (pH 2.0) and its cathodic stripping during the potential scan (100 mV s^?1). The linear range for the determination of As(III) in the presence of SDDC (4 μmol L^?1) in water samples was between 1 and 10 μg L^?1 for a deposition time of 300 s (r=0.994) and between 10 and 100 μg L^?1 for a deposition time of 60 s (r=0.999). For the determination of As(III) in dialysis concentrate samples, the linear range was between 5 and 25 μg L^?1 for a deposition time of 180 s (r=0.992) and between 10 and 100 μg L^?1 for a deposition time of 60 s (r=0.996). Detection limits of 0.3 and 2.2 μg L^?1 in water and dialysis concentrate samples were calculated for the method using a deposition time of 300 and 180 s, respectively. Recovery values between 93.0 and 110.0% for As(III) added to deionized, mineral, seawater (synthetic and real) and dialysis concentrate samples prove the satisfactory accuracy and applicability of the procedure.     

Electrochemical performance of metal-organic framework synthesized by a solvothermal method for supercapacitors

A series of metal-organic frameworks (MOFs) based on isonicotinic acid and nickel nitrate were successfully synthesized by a solvothermal method as electrode materials for supercapacitor. The MOF were examined by X-ray diffraction (XRD) patterns and N₂ adsorption/desorption isotherms. Electrochemical properties of the materials were characterized by cyclic voltammetry (CV) in 6 M KOH aqueous solutions. The effect of solvothermal time, temperature and the mol ratio of isonicotinic acid and nickel nitrate on the electrochemical performance were also studied. The maximum specific capacitance is found to be 634 F g^?1 at 5 mV s^?1 and the stable cycling properties measurement showed the sample kept 84% after 2000 cycles at a 50 mV s^?1 scan rate.