电解质材料Sr-和Mg-掺杂LaGaO3的制备及性能研究

A dense La_0.8Sr_0.2Ga_0.83Mg_0.17O_2.815 electrolyte in pure perovskite phase was prepared by a polyacrylic acid assisted solid state reaction method, and the effects of La source on the structure and electrochemical performance were also studied. By means of XRD and SEM, the structure of this material was characterized, and the electrochemical properties were studied through AC impedance diagram. The results show that the sample presents a single perovskite-type phase after sintering at 1 450 ℃ and the relative density is 94%. The specimen has the lower activate energy and higher electrical conductivity at 600 ℃. There are two different activation energy at the turning point of 650 ℃, which are 74.6 and 42.4 kJ·mol^-1, respectively. The electrical conductivity is 0.057 S·cm^-1 and 0.017 S·cm^-1 at the temperature of 800 ℃ and 600 ℃, respectively.     

Ce0.8Y0.2O1.9-Ca3(PO4)2-K3PO4复合电解质在中温区的质子导电性及在常压合成氨中的应用

A precursor of Ce_0.8Y_0.2O_1.9(YDC) solid electrolyte was synthesized by the gol-gel method. YDC and phosphates powders were prepared by mixing the YDC and phosphates according to different weight ratios. The mixtures of the YDC and binary phosphates were ground and sintered at 1 400 ℃. The proton conductivity in solid electrolyte of the sintered samples was examined using electrochemical methods at 400～800 ℃. Ammonia was synthesized from nitrogen and hydrogen at atmospheric pressure in the solid state proton conducting cell reactor. The optimal condition for the ammonia production was determined. The result indicated that composite electrolyte of 80wt% YDC: 20wt% binary phosphates as proton conductor could obtain the highest ionic conductivity and ammonia production rate among the four samples, the rate of evolution of ammonia was up to 9.5 × 10^-9 mol·s^-1·cm^-2.     

SrCe0.95Er0.05O3-α固体电解质的导电性

SrCe_0.95Er_0.05O_3-α ceramic of a single orthorhombic phase of perovskite-type SrCeO₃ was prepared by high-temperature solid state reaction. Using the ceramic as solid electrolyte and porous platinum as electrodes, the measurements of conductivities and ionic transport numbers on SrCe_0.95Er_0.05O_3-α ceramic were performed by using electrochemical methods in the temperature range of 600～1 000 ℃ in wet hydrogen, dry air and wet air, respectively. The results indicate that the sample is a pure protonic conductor with a maximal conductivity of 0.01 S·cm^-1 in wet hydrogen, a mixed conductor of oxide-ion and hole in dry air, and a mixed conductor of proton, oxide-ion and hole in wet air.     

新型阴极材料Ba0.5Sr0.5Co0.8Fe0.2O3-σ制备与性能研究

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-σ(BSCF), a new cathode material for solid oxide fuel cell (SOFC), was synthesized by polyacrylicacid (PAA) method. The lattice structures of samples calcined at different temperatures were characte-rized by XRD. Shrinkage, porosity and pore size of the porous BSCF as a function of sintering temperature were investigated. It was found that the cubic perovskite structure could be formed after calcination at 800 ℃ for 2 h, but not well crystallized as seen from some unknown phases, and the pure cubic perovskite structure was formed after calcination at 1 150 ℃ for 2 h. The particle size of BSCF was less than 1～2 μm. The shrinkage of the porous BSCF increased with sintering temperature, but the opposite was true for the porosity. After sintering at 1 100 ℃ for 4 h, the porous BSCF was still in an appropriate structure, with porosity of 29% and electrical conductivity above 400 S·cm^-1.     

稀土钨青铜K0.71Nd0.028WO3的制备及其电性能

Tetragonal tungsten bronze K_0.71Nd_0.028WO₃ was synthesized by rare earth co-permeation method using Keggin type POMs of α-K₁₀[SiCu₃(OH₂)W₉O₃₇]·6H₂O (abbreviated as SiW₉Cu₃) as precursor. XRD, XPS, XRF, TG-DTA were used to characterize the resulting material. The XPS results indicate that Nd has permeated and diffused into the body of the sample and exists in tungsten bronze in the form of K_0.71Nd_0.028WO₃. The results of TG-DTA show that K_0.71Nd_0.028WO₃ begins to decompose at 320 ℃. The consequence of DC four-probe shows that the conductivity of the sample permeated by rare earth is 10³ times higher than that of the sample only permeated by methanol at room temperature. The conductivity of the sample only permeated by methanol is only 10^-3 S·cm^-1 but the conductivity of the sample permeated by rare earth is 1.65 S·cm^-1.     

尖晶石Li4Ti5O12中锂离子的化学扩散系数的研究

A relatively simple galvanostatic method was used for the evaluation on the average chemical diffusion coefficient of lithium-ion in spinel Li₄Ti₅O₁₂ prepared by solid-state reaction technique. The diffusion coefficient of lithium-ion was estimated to be 2.8×10^-13 cm²·s^-1 and 1.3×10^-13 cm²·s^-1 for charge and discharge， respectively.     

Sintering behavior and ionic conductivity of Ce<Subscript>0.8</Subscript>Gd<Subscript>0.2</Subscript>O<Subscript>1.9</Subscript> with a small amount of MnO<Subscript>2</Subscript> doping

A 20% GdO_1.5 doped ceria solid solution with a small amount of MnO₂ doping (≤5% molar ratio) was prepared via the mixed oxide method from high-purity commercial powders with grain size around 0.2–0.5 μm. X-ray diffraction analysis indicated that all the samples exhibited the fluorite structure, and no new phase was found. The data from dilatometeric measurements and scanning electron microscopy observations revealed that 1% Mn doping reduced the sintering temperature by over 150 °C, and enhanced the densification and grain growth. Mn doping has little effect on grain interior conductivity, but a marked deterioration in grain boundary behavior is observed. This leads to a lower total conductivity in comparison with the undoped Ce_0.8Gd_0.2O_2–δ. Therefore, for solid oxide fuel cells (SOFCs) with Mn-containing compounds as electrodes, optimization of electrode fabrication conditions is needed to prevent the formation of a lower conductivity layer at the electrode/electrolyte interface since Mn will diffuse from the electrode side to the electrolyte during fabrication and operation of SOFCs. Electronic Publication     

La0.9Sr0.1Al0.9Mg0.1O3-δ-Ca3(PO4)2-K3PO4复合电解质的合成及在常压天然气合成氨中的应用

La_0.9Sr_0.1Al_0.9Mg_0.1O_0.9(LSAM) was synthesized by the sol-gel method, an oxide-salt composite electrolyte LSAM-Ca₃(PO₄)₂-K₃PO₄ was prepared by mixing the LSAM and phosphates. The mixture was ground and sintered at 1 400 ℃. Using the LSAM electrolyte and its oxide-salt composite as solid electrolytes and silver-palladium alloy as electrodes, electrical conductivity was measured at different conditions. Ammonia was synthesized from wet natural gas and nitrogen at atmospheric pressure in the solid state proton conducting cell reactor and the optimal conditions for ammonia production were determined. The oxide-salt composite exhibited much higher ionic conductivity and ammonia production rate than that of the LSAM electrolyte at 400～800 ℃, the rate of evolution of ammonia was up to 5.30 × 10^-9 mol·cm^-2·s^-1.     

CexPr1-xO2-δ复合氧化物的XRD和Raman表征

A series of Ce_xPr_1-xO_2-δ mixed oxides were synthesized by sol-gel method and characterized by Raman and XRD techniques. When x value was changed from 1.0 to 0.5, only a cubic phase CeO₂ was observed. The samples were very well crystallized on decreasing x from 0.50 to 0.99. For Ce_xPr_1-xO_2-δ samples 465 cm^-1 and 1 150 cm^-1 Raman peaks are attributed to the Raman active F_2g mode of CeO₂. The broad peak at about 570 cm^-1 in the region of 0.3 ≤x≤ 0.99 can be linked to lattice defects resulting in oxygen vacancies. The new band at about 195 cm^-1 may be attributed to the asymmetric vibration caused by the formation of oxygen vacancies. Calcination temperatures had great effect on the peak intensity for CeO₂ but less effect on Ce_0.8Pr_0.2O_2-δ in Raman spectra. It might be due to the transformation of the colors for the mixed oxides, the insertion of Pr atom into the ceria lattice could enhance the sintering resistance and thermal stability of the mixed oxides.     

铜取代Dawson结构杂多钨磷酸电荷转移配合物的合成与性质研究

Two new charge-transfer complexes, (DMAH)₁₀［CuP₂W₁₇O₆₂］·DMF·2H₂O and (DMAH)₁₄［Cu₂P₂W₁₆O₆₂］ have been prepared in aqueous solution from N,N′-dimethylaniline(DMA) and copper substituted polyoxotungstates with Dawson Structure, and characterized by elemental analysis, ICP, TG, IR, diffusion reflectance electronic spectra, polarography, and CV. The results indicate that the structure of anion has little change after the charge-transfer complexes are formed, but the characteristic vibrational bands have some red shift or blue shift. The charge transfer takes place under sunlight. There is a new absorption band at 625 nm in the solid reflectance electronic spectra of the complexes, it is ascribed to the IVCT (W(V)→W(Ⅵ) band of the reduced anion ［CuP₂W₁₇O₆₂］^10-. The conductivities at room temperature of title complexes are 3.6×10^-9 S·cm^-1 and 5.4×10^-9 S·cm^-1, respectively. Both of them are weak semiconductors.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Phase relations in the K2W2O7-K2WO4-KPO3-Bi2O3 system and structure of K6.5Bi2.5W4P6O34

The phase relations in the cross-section of the K₂W₂O₇-K₂WO₄-KPO₃ containing 15 mol% Bi₂O₃ were undertaken using flux method. Crystallization fields of K_6.5Bi_2.5W₄P₆O₃₄, K₂Bi(PO₄)(WO₄), Bi₂WO₆, KBi(WO₄)₂ and their cocrystallization areas were identified. Novel phase K_6.5Bi_2.5W₄P₆O₃₄ was characterized by single-crystal X-ray diffraction: sp. gr. P−1, a=9.4170(5), b=9.7166(4), c=17.6050(7) Å, α=90.052(5)°, β=103.880(5)° and γ=90.125(5)°. It has a layered structure, which contains {K₇Bi₅W₈P₁₂O₆₈}_∞ layers stacked parallel to ab plane and sheets composed by potassium atoms separating these layers. Sandwich-like {K₇Bi₅W₈P₁₂O₆₈}_∞ layers are assembled from [W₂P₂O₁₃]_∞ and [BiPO₄]_∞ building units, and are penetrated by tunnels with K/Bi atoms inside. FTIR-spectra of K₂Bi(PO₄)(WO₄) and K_6.5Bi_2.5W₄P₆O₃₄ were discussed on the basis of factor group theory.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Extension of the La7Mo7O30 structural type with La7Nb3W4O30 and La7Ta3W4O30 compounds

Two compounds of formula La₇A₃W₄O₃₀ (with A=Nb and Ta) were prepared by solid-state reaction at 1450 and 1490 °C. They crystallize in the rhombohedric space group R-3 (No. 148), with the hexagonal parameters: , and , . The structure of the materials was analyzed from X-ray, neutron and electronic diffraction. These oxides are isostructural of the reduced molybdenum compound La₇Mo₇O₃₀, which are formed of perovskite rod along [111]. An order between (Nb, Ta) and W is observed.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Preparation and structure of NaSr0.5Al2B2O7 and NaCa0.5Al2B2O7

Two compounds NaSr_0.5Al₂B₂O₇ and NaCa_0.5Al₂B₂O₇, have been found to crystallize into a new structure type by Rietveld refinement from X-ray powder diffraction data. Their structure belongs to hexagonal space group P6₃/m, with lattice parameters of , for NaSr_0.5Al₂B₂O₇ and , for NaCa_0.5Al₂B₂O₇, respectively. The structure is built up by [Al₂B₂O₇]²⁻ double layer and Na⁺/Ca²⁺ or Na⁺/Sr²⁺ ions alternatively stacking along the c-axis. The sites in the inter-double layer are fully occupied jointly by Na and Ca or Sr, but the intra-double layer sites are only half occupied solely by Na. A mechanism of the transition of the structure from CaAl₂B₂O₇ to present structure type by replacing only 1% Ca by Na (2%) as observed by Chang and Keszler (Mater. Res. Bull. 33 (1998) 299) is also proposed.     

SnSbBiS4-SnS and SnSbBiS4-Sn2Sb6S11 sections of the SnS-Sb2S3-Bi2S3 ternary system

SnSbBiS₄-SnS and SnSbBiS₄-Sn₂Sb₆S₁₁ sections were studied by physicochemical methods (DTA, X-ray powder diffraction, microstructure observation, and microhardness measurements). These sections were found to be eutectic quasi-binary sections of the SnS-Sb₂S₃-Bi₂S₃ ternary system. Solid solution regions based on the initial components were found on either side of the sections. Alloys in the solid solution region are p-type semiconductors.     

Synthesis and characterization of quaternary selenides Sn2Pb5Bi4Se13 and Sn8.65Pb0.35Bi4Se15

Quaternary selenides Sn₂Pb₅Bi₄Se₁₃ and Sn_8.65Pb_0.35Bi₄Se₁₅ were synthesized from the elements in sealed silica tubes; their crystal structures were determined by single-crystal and powder X-ray diffraction. Both compounds crystallize in monoclinic space group C2/m (No.12), with lattice parameters of Sn₂Pb₅Bi₄Se₁₃: a = 14.001(6) Å, b = 4.234(2) Å, c = 23.471(8) Å, V = 1376.2(1) Å³, R₁/wR₂ = 0.0584/0.1477, and GOF = 1.023; Sn_8.65Pb_0.35Bi₄Se₁₅: a = 13.872(3) Å, b = 4.2021(8) (4) Å, c = 26.855(5) Å, V = 1557.1(5) Å³, R₁/wR₂ = 0.0506/0.1227, and GOF = 1.425. These compounds exhibit tropochemical cell-twinning of NaCl-type structures with lillianite homologous series L(4, 5) and L(4, 7) for Sn₂Pb₅Bi₄Se₁₃ and Sn_8.65Pb_0.35Bi₄Se₁₅, respectively. Measurements of electrical conductivity indicate that these materials are semiconductors with narrow band gaps; Sn₂Pb₅Bi₄Se₁₃ is n-type, whereas Sn_8.65Pb_0.35Bi₄Se₁₅ is a p-type semiconductor with Seebeck coefficients −80(5) and 178(7) μV/K at 300 K, respectively.     

Structural chemistry of Sr3Cr2WO9, Ca3Cr2WO9, and Ba3Cr2WO9

We have studied the preparation and crystallographic structure of three perovskite-type compounds: Sr₃Cr₂WO₉, cubic, the lattice parameter of which is a = 7.812Å; Ca₃Cr₂WO₉, tetragonal, the lattice parameters of which are a = 5.408 Å and c = 7.635Å; and Ba₃Cr₂WO₉, hexagonal, the lattice parameters of which are a = 5.691 Å and c = 13.957Å. We have compared these three structures and shown the relationship between the dimensions of the alkaline-earth metal and the existence of the different structures.