Continuous monitoring for cyanide in waste water with a galvanic hydrogen cyanide sensor using a purge system

A continuous monitoring system for cyanide with a galvanic hydrogen cyanide sensor and an aeration pump for purging was developed. Hydrogen cyanide evolved from cyanide solution using a purging pump was measured with the hydrogen cyanide sensor. The system showed good performance in terms of stability and selectivity. A linear calibration curve was obtained in the concentrating range from 0 to 15 mg dm³ of cyanide ion with a slope of −0.24 μA mg⁻¹ dm⁻³. The lower detection limit was 0.1 mg dm⁻³. The 90% response time of the sensor system was within 3.5 min for a 0.5 mg dm⁻³ cyanide solution, when the flow rate of the purging air was 1 dm³ min⁻¹. The system maintained the initial performance for 6 months in the field test. The developed galvanic sensor system was not subject to interference from sulfide and residual chlorine, compared with a potentiometric sensor system developed previously. The analytical results obtained by the present system were in good agreement with those obtained by the pyridine pyrazolone method. The correlation factor and regression line between both methods were 0.979 and Y=2.30×10⁻⁴+1.12X, respectively. This system was successfully applied for a continuous monitoring of cyanide ion in waste water.     

Can chlorine anion catalyze the reaction of HOCl with HCl?

The reaction of HOCl + HCl → Cl₂ + H₂O in the presence of chlorine anion Cl⁻ has been studied using ab initio methods. The overall exothermicity is 15.5 kcal mol⁻¹ and this reaction has been shown to have a high activation barrier of 46.5 kcal mol⁻¹. Cl⁻ is found to catalyze the reaction via the formation of HOCl·Cl⁻, ClH·HOCl·Cl⁻ and Cl⁻·H₂) intermediate ion-molecule complexes or by interacting with a concerted four-center transition state of the reaction of HOCl + HCl.     

Cellulose based macromolecular chelator having pyrocatechol as an anchored ligand: synthesis and applications as metal extractant prior to their determination by flame atomic absorption spectrometry

Pyrocatechol is immobilized on cellulose via ---NH---CH₂---CH₂---NH---SO₂---C₆H₄---N=N--- linker and the resulting macromolecular chelator characterized by IR, TGA, CPMAS ¹³C NMR and elemental analyses. It has been used for enrichment of Cu(II), Zn(II), Fe(III), Ni(II), Co(II), Cd(II) and Pb(II) prior to their determination by flame atomic absorption spectrometry (FAAS). The pH ranges for quantitative sorption (98.0–99.4%) are 4.0–7.0, 5.0–6.0, 3.0–4.0, 5.0–7.0, 5.0–8.0, 7.0–8.0 and 4.0–5.0, respectively. The desorption was found quantitative with 0.5 mol dm⁻³ HCl/HNO₃ (for Pb). The sorption capacity of the matrix for the seven metal ions has been found in the range 85.3–186.2 μmol g⁻¹. The optimum flow rate of metal ion solution for quantitative sorption of metal onto pyrocatechol functionalized cellulose as determined by column method, is 2–6 cm³ min⁻¹, whereas for desorption it is 2–4 cm³ min⁻¹. The tolerance limits for NaCl, NaBr, NaI, NaNO₃, Na₂SO₄, Na₃PO_4, humic acid, EDTA, ascorbic acid, citric acid, sodium tartrate, Ca(II) and Mg(II) in the sorption of all the seven metal ions are reported. Ascorbic acid is tolerable up to 0.8 mmol dm⁻³ with Cu and Pb where as sodium tartrate does not interfere up to 0.6 mmol dm⁻³ with Pb. There is no interference of NaBr, NaCl and NaNO₃ up to a concentration of 0.5 mol dm⁻³, in the sorption of Cu(II), Cd(II) and Fe(III) on to the chelating cellulose matrix The preconcentration factors are between 75 and 300 and t_1/2 values ≤5 min for all the metal ions. Simultaneous sorption of Cu, Zn, Ni and Co is possible at pH 5.0 if their total concentration does not exceed lowest sorption capacity. The present matrix coupled with FAAS has been used to enrich and determine the seven metal ions in river and tap water samples (relative standard deviation (R.S.D.) 1.05–7.20%) and synthetic certified water sample SLRS-4 (NRC, Canada) with R.S.D. 2.03%. The cobalt present in pharmaceutical vitamin tablets was also preconcentrated on the modified cellulose and determined by FAAS (R.S.D. 1.87%).     

Determination of chlorine and bromine in rocks by alkaline fusion with ion chromatography detection

This study describes the use of alkaline fusion by sodium peroxide to dissolve chlorine and bromine in rocks to produce a solution which, with appropriate pre-treatment, is suitable for analysis by ion chromatography. Results are given for a selection of sedimentary and igneous rocks. The accuracy of the fusion method is evaluated by analysis of Geological Survey of Japan reference materials. Additionally, a spike recovery test is performed to show that the fusion process is quantitative for chlorine and bromine. The results for chlorine are in the range 58–3860 mg kg⁻¹ and show good agreement both with results obtained by pyrohydrolysis with flow injection colorimetric detection and results obtained by aqueous leaching of the samples with ion chromatography detection. Results for bromine are in the range <3–4.5 mg kg⁻¹. Because of the relatively few data obtained in this study and the relative paucity of published data for reference materials, an assessment of the accuracy of the fusion method for bromine is more difficult. The limits of detection for this method are 36 and 3 mg kg⁻¹ for chlorine and bromine, respectively.     

Pyrocatechol Violet immobilized Amberlite XAD-2: synthesis and metal-ion uptake properties suitable for analytical applications

Amberlite XAD-2 has been functionalized by coupling it, through the ---N=N--- group, with Pyrocatechol Violet (PV), and the resulting resin has been characterized by elemental analysis, thermogravimetric analysis (TGA) and IR spectra. The resin has been used for preconcentrating Zn(II), Cd(II), Pb(II) and Ni(II) ions prior to their determination by flame atomic absorption spectrometry. The optimum pH values for quantitative sorption are 5, 5–7, 4, and 3 for Zn, Cd, Pb and Ni, respectively. The four metals can be desorbed (recovery ˜98%) with 4 M HNO₃; also, 4 M HCl is equally suitable except for Zn. The sorption capacity of the resin is 1410, 1270, 620 and 1360 μg g⁻¹ resin for Zn, Cd, Ni and Pb, respectively. The effect of F⁻, Cl⁻, NO₃⁻, SO₄²⁻ and PO₄³⁻ on the sorption of these four metal ions has been investigated. They are tolerable in the range 0.01–0.20 M, for Pb. In the sorption of Zn(II) and Ni(II), the tolerance limits of all these ions are upto 0.01 M, whereas for Cd(II), F⁻, NO₃⁻, and PO₄³⁻ have been found to be tolerable upto 0.50, 0.10 and 0.10 M, respectively. The preconcentration factors are 60, 50, 23 and 18 for Zn, Cd, Pb and Ni, respectively. Simultaneous collection and determination of the four metals are possible. Cations commonly present in drinking water do not affect the sorption of either metal ion if present at a concentration level similar to that of water. The method has been applied to determine Zn, Ni and Pb content of well-water samples (RSD ≤9%).     

The use of microemulsion for determination of sodium and potassium in biodiesel by flame atomic absorption spectrometry

A new method for F AAS determination of sodium and potassium in biodiesel using water-in-oil microemulsion as sample preparation is proposed. The method was investigated for biodiesel produced from different sources, as soybean, castor and sunflower oil and animal fat and was also applied for vegetable oils. The optimized condition for microemulsion formation was 57.6% (w/w) of n-pentanol, 20% (w/w) of biodiesel or vegetable oil, 14.4% (w/w) of Triton X-100 and 8% (w/w) of water (aqueous standard of KCl or NaCl in/or diluted HNO₃). The optimized instrumental parameters were: aspiration rate of 2 mL min⁻¹ and the flame composition of 0.131 of C₂H₂/air ratio. For comparison purpose, the determination of sodium and potassium were also carried out according to European norms (EN 14108 and EN 14109, respectively). These norms are applied for determination of sodium and potassium in fatty acid methylic ester samples and consist in the sample dilution using organic solvent and determination by F AAS. The stability of microemulsified aqueous standards and samples was investigated and it was found to be stable for at least 3 days while the organic standard diluted with xylene showed a decrease around of 15% in the analytical signal in 1 h. The limits of detection were 0.1 μg g⁻¹ and 0.06 μg g⁻¹ and the obtained characteristic concentrations were 25 μg L⁻¹ and 28 μg L⁻¹ for sodium and potassium, respectively. The proposed method presented two times better limits of detection and better precision (0.4–1.0%) when compared with the dilution technique (1.5–4.5%). The accuracy of the method was evaluated through recovery tests and comparison with the results obtained by dilution technique. The recoveries ranged from 95% to 115% for biodiesel and 90% to 115% for vegetable oil samples. Comparison between the results obtained for biodiesel by both methods showed no significant differences at the 95% confidence level according to a Student's t-test. This study shows that the proposed method based on microemulsion as sample preparation can be applied as an efficient alternative for sodium and potassium determination in biodiesel samples.     

Spectrophotometric determination of nitrate and nitrite in soil and water samples with a diazotizable aromatic amine and coupling agent using column preconcentration on naphthalene supported with ion-pair of tetradecyldimethylbenzylammonium and iodide

Composite diazotization-coupling reagents containing sulfanilamide (SAM), sulfapyridine (SP) or sulfathiazole (ST) as the diazotizable aromatic amines and sodium 1-naphthol-4-sulfonate (NS) as the coupling agent using column preconcentration on naphthalene-tetradecyldimethylbenzylammonium(TDBA)-iodide adsorbent have been used for the spectrometric determination of trace nitrate and nitrite in soil and water samples. Nitrite ion reacts with SAM in the pH range 2.0–5.0, SP in the pH range 2.0–2.5 and ST in the pH range 2.0–3.3 in HCl medium to form water-soluble colourless diazonium cations. These cations were coupled with NS in the pH range 9.0–12.0 for the SAM system, 9.6–12.0 for the SP system and 8.5–12.0 for the ST system to be retained on naphthalene-TDBA-I material packed in a column. The solid mass is dissolved from the column with 5 ml of dimethylformamide and the absorbance is measured spectrometerically at 543 nm for SAM-NS, 533 nm for SP-NS and 535 nm for ST-NS. Nitrate is reduced to nitrite by a copper-coated cadmium reductor column and the nitrite is then treated with the diazotization-coupling reagent by column preconcentration. The absorbance due to the sum of nitrate and nitrite is measured and nitrate is determined by difference. The calibration graph was linear over the range 2–40 ng NO₂⁻-N ml⁻¹ and 1.5–30 ng NO₃⁻-N ml⁻¹ in aqueous samples for the SAM and ST systems and 2–48 ng NO₂⁻-N ml⁻¹ and 1.5–36 ng NO₃⁻-N ml⁻¹ in aqueous samples for the SP system, respectively. The sensitivity, accuracy and precision of the systems decreased in the order STSAMSP. The detection limits were 1.4 ng NO₂⁻-N ml⁻¹ and 1.1 ng NO₃⁻-N ml⁻¹ for SAM, 1.6 ng NO₂⁻-N ml⁻¹ and 1.2 ng NO₃⁻-N ml⁻¹ for SP, and 1.0 ng NO₂⁻-N ml⁻¹ and 0.75 ng NO₃⁻-N ml⁻¹ for ST, respectively. The preconcentration factors are 8, 5 and 6 for SAM-NS, SP-NS and ST-NS, respectively. Interferences from various foreign ions have been studied and the methods have been applied to the determination of ng ml⁻¹ levels of nitrite and nitrate in soil and water samples. The mean recovery was 95–102% for all three systems.     

Gas phase hydrogen deuterium exchange reactions of a model peptide: FT-ICR and computational analyses of metal induced conformational mutations

We utilized gas phase hydrogen/deuterium (H/D) exchange reactions and ab initio calculations to investigate the complexation between a model peptide (Arg-Gly-AspRGD) with various alkali metal ions. The peptide conformation is drastically altered upon alkali metal ion complexation. The associated conformational changes depend on both the number and type of complexing alkali metal ions. Sodium has a smaller ionic diameter and prefers a multidentate interaction that involves all three amino acids of the peptide. Conversely, potassium and cesium form different types of complexes with the RGD. The [RGD + 2Cs − H]⁺ species exhibit the slowest H/D exchange reactivity (reaction rate constant of 6 × 10⁻¹³ cm³molecule⁻¹s⁻¹ for the fastest exchanging labile hydrogen with ND₃). The reaction rate constant of the protonated RGD is two orders of magnitude faster than that of the [RGD + 2Cs − H]⁺. Addition of the first cesium to the RGD reduces the H/D exchange reaction rate constant (i.e., D₀) by a factor of seven whereas sodium reduces this value by a factor of thirty. Conversely, addition of the second alkali metal ions has the opposite effect; the rate of D₀ disappearance for all [RGD + 2Met − H]⁺ species (MetNa, K, and Cs) decreases with the alkali metal ion size.     

8-Hydroxyquinoline anchored to silica gel via new moderate size linker: synthesis and applications as a metal ion collector for their flame atomic absorption spectrometric determination

The silica gel modified with (3-aminopropyl-triethoxysilane) was reacted with 5-formyl-8-hydroxyquinoline (FHOQ_x) to anchor 8-quinolinol ligand on the silica gel. It was characterised with cross polarisation magic angle spinning (CPMAS) NMR and diffuse reflectance infrared Fourier transformation (DRIFT) spectroscopy and used for the preconcentration of Cu(II), Pb(II), Ni(II), Fe(III), Cd(II), Zn(II) and Co(II) prior to their determination by flame atomic absorption spectrometry. The surface area of the modified silica gel has been found to be 227 m² g⁻¹ and the two pKa values as 3.8 and 8.0. The optimum pH ranges for quantitative sorption are 4.0–7.0, 4.5–7.0, 3.0–6.0, 5.0–8.0, 5.0–8.0, 5.0–8.0 and 4.0–7.0 for Cu, Pb, Fe, Zn, Co, Ni and Cd, respectively. All the metals can be desorbed with 2.5 mol l⁻¹ HCl or HNO₃. The sorption capacity for these metal ions is in range of 92–448.0 μmol g⁻¹ and follows the order Cd3, NaCl, NaBr, Na₂SO₄ and Na₃PO₄, glycine, sodium citrate, EDTA, humic acid and cations Ca(II), Mg(II), Mn(II) and Cr(III) in the sorption of all the seven metal ions are reported. The preconcentration factors are 150, 250, 200, 300, 250, 300 and 200 for Cd, Co, Zn, Cu, Pb, Fe and Ni, respectively and t_1/2 values <1 min except for Ni. The 95% extraction by batch method takes ≤25 min. The simultaneous enrichment and determination of all the metals are possible if the total load of the metal ions is less than sorption capacity. In river water samples all these metal ions were enriched with the present ligand anchored silica gel and determined with flame atomic absorption spectrometer (R.S.D.≤6.4%). Cobalt contents of pharmaceutical samples (vitamin tablet) were preconcentrated with the present chelating silica gel and estimated by flame AAS, with R.S.D.1.4%. The results are in the good agreement with the certified value, 1.99 μg g⁻¹ of the tablets. Iron and copper in certified reference materials (synthetic) SLRS-4 and SLEW-3 have been enriched with the modified silica gel and estimated with R.S.D.<5%.     

Peroxidase immobilized on Amberlite IRA-743 resin for on-line spectrophotometric detection of hydrogen peroxide in rainwater

The importance of atmospheric hydrogen peroxide (H₂O₂) in the oxidation of SO₂ and other compounds has been well established. A spectrophotometric method for the determination of hydrogen peroxide in rainwater is proposed. This method is based on selective oxidation of hydrogen peroxide using an on-line tubular reactor containing peroxidase immobilized on Amberlite IRA-743 resin. The hydrogen peroxide in the presence of phenol, 4-aminoantipyrine and peroxidase, produces a red compound (λ = 505 nm). Beer's law is obeyed in a concentration range of 1–100 μmol l⁻¹ hydrogen peroxide with an excellent correlation coefficient (r = 0.9991), at pH 7.0, with a relative standard deviation (R.S.D.) <2%. The detection limit of the method is 0.7 μmol l⁻¹ (4.8 ng of H₂O₂ in a 200 μl sample). Measurements of hydrogen peroxide in rain samples were carried out over the period from November 2003 to January 2005, in the central area of the Juiz de Fora city, Brazil. The concentration of H₂O₂ varied from values lower than the detection limit to 92.5 μmol l⁻¹. The effects of the presence of nonseasalt (NSS) SO₄²⁻, NO₃⁻ and H⁺ in the concentration of hydrogen peroxide in the rainwater had been evaluated. The average concentrations of H₂O₂, NO₃⁻, NSS SO₄²⁻ and SO₄²⁻ are 23.4, 18.9, 7.9 and 10.3 μmol l⁻¹, respectively. The pH values for 82% of the collected samples are greater than 5.0. The spectrophotometeric method developed in this work that uses enzyme immobilized on the resin ion-exchange compared with the amperometric method did not present any significant difference in the results.     

Fingerprint patterns from laser-induced Azido photochemistry of spin-labeled photoaffinity ATP analogs in matrix-assisted laser desorption/ionization mass spectrometry

The photochemical reaction of azide derivatives induced by ultraviolet (UV) laser in matrix-assisted laser desorption/ionization mass spectrometry (MALDI) is reported. A novel synthesized class of azide aromatic derivatives, spin-labeled photoaffinity non-nucleoside adenosine triphosphate (ATP) analogs which are useful probes in study of muscle contraction mechanism, is used in this investigation. In the negative ion MALDI spectra of these ATP analogs, “fingerprint” peaks corresponding to [M − 10 − 1]⁻, [M − 12 − 1]⁻, [M − 16 − 1]⁻, [M − 26 − 1]⁻, [M − 28 − 1]⁻, [M − 41 − 1]⁻, and [M − 42 − 1]⁻ were observed with relative intensities depending on the MALDI matrix. Only the [M − 16 − 1]⁻ is present in the similar mass spectra of the analog in which the azido group is replaced by a hydrogen. A model is suggested for the photochemical reactions of azide derivatives under UV laser irradiation. The photoreaction fingerprint information is diagnostically useful in characterization of azido compounds, especially for spin-labeled photoaffinity non-nucleoside ATP analogs.     

Quantification of copper and zinc species fractions in legume seeds extracts by SEC/ICP-MS: validation and uncertainty estimation

Fractions of Cu and Zn species in legume samples (common white bean, pea, chick pea and lentil seeds and defatted soybean flour) were analysed by on-line hyphenation of size exclusion chromatography and inductively coupled plasma-mass spectrometry. Samples were extracted by 0.02 mol l⁻¹ Tris–HCl buffer solution, pH 7.5. The extraction efficiency lay in the region 60–90 and 60–80% for Cu and Zn, respectively. Quantification of elements in the individual chromatographic fractions was carried out by isotope dilution (ID) and external calibration (EC) techniques. For ID analysis the chromatographic effluent was mixed with the flow of ⁶⁵Cu and ⁶⁸Zn isotope enriched solution and the isotope ratio values ⁶³Cu/⁶⁵Cu and (⁶⁴Zn+⁶⁶Zn)/⁶⁸Zn were measured. In the case of EC technique calibration solutions of elements were injected to the flow of mobile phase by the second injector. Prior entering detector the effluent was mixed with the flow of internal standard solution (In, 50 μg l⁻¹). Both methods have similar precision, however the behaviour of both studied elements was not the same. The chromatographic analysis itself was the main source of variability in the case of Cu. For Zn species analysis, the extraction process and the manipulation with the extract, played the significant role too. It was probably caused by lower stability of the present zinc chelates. The total amounts of Zn found in all chromatographic fractions represented 85–95% of Zn in sampled extract whereas those of Cu approached 100%. In case of small peaks the results of ID and EC were not the same. The EC results were lower then ID results. The great deal of results uncertainty accounts for the precision.     

Methods for separation of trace amounts of platinum and investigation of the influence of interfering elements during platinum determination in copper ores and copper concentrates by graphite furnace atomic absorption spectrometry

A THGA graphite furnace with Zeeman background correction has been used to determine platinum content in copper ore and copper concentrate at the part per billion (ppb) concentration level. Two different procedures for the separation of trace platinum have been applied: (i) use of an ion exchange resin; and (ii) a two-stage method based on platinum separation on inorganic carriers. The influence of interfering elements in the matrix (Cu, Pb, Fe, Ti, V, Au, Pd, Ir, Rh and Al) has been examined using a graphite furnace. It was found that the presence of Cu (12.5–100 mg l⁻¹), Pb (100–500 mg l⁻¹), Fe (100–2000 mg l⁻¹), Ti (25–100 mg l⁻¹), V (25–100 mg l⁻¹), Au (25–300 mg l⁻¹), Pd (20–250 mg l⁻¹), Ir (0.5–3.5 mg l⁻¹) and Rh (0.025–1 mg l⁻¹) in the samples analyzed has no effect on the platinum absorption signal when using a recommended temperature program (T_pyr=1300°C, T_at=2450°C). Spectral interference was observed, which was due to aluminum, as a result of the close neighborhood of the Pt 265.945-nm and Al 266.039-nm lines. This interference could not be eliminated by the Zeeman background correction.     

An ab initio close-coupling calculation of the lower vibrational energies of the HCl dimer

We have previously determined an analytical ab initio six-dimensional potential energy surface for the HCl dimer, and in the present paper we use this potential, with the HCl bond lengths held fixed, in a full (four-dimensional) close-coupling calculation to determine the energies of the lowest 24 vibrational states. These vibrational states involve the intermolecular stretch ν₄, the trans-bend tunneling vibration ν₅, and the torsion ν₆. The highest of the 24 levels is the (ν₄ν₅ν₆)=(111) state, for which we calculate an energy of 200 cm⁻¹ above the (000) state. As well as determining tunneling energies up to 5ν₅=183 cm⁻¹, we determine ν₄=49 cm⁻¹, 2ν₄=93 cm⁻¹, 3ν₄=134 cm⁻¹, 4ν₄=172 cm⁻¹, ν₆=137 cm⁻¹ and ν₄+ν₆=178 cm⁻¹, together with tunneling energies in all these states. Making allowance for the HCl stretching zero-point energy we determine the dissociation energy D₀ as 390 cm⁻¹ on this analytical surface. We determine that below 300 cm⁻¹ there are 72 vibrational (J=K=0) states, and below dissociation there are 162 vibrational (J=K=0) states, for this potential surface.     

Flow injection determination of bismuth in urine by successive retention of Bi(III) and tetrahydroborate(III) on an anion-exchange resin and hydride generation atomic absorption spectrometry

Bismuth as BiCl₄⁻ and BH₄⁻ ware successively retained in a column (150 mm × 4 mm, length × i.d.) packed with Amberlite IRA-410 (strong anion-exchange resin). This was followed by passage of an injected slug of hydrochloric acid resulting in bismuthine generation (BiH₃). BiH₃ was stripped from the eluent solution by the addition of a nitrogen flow and the bulk phases were separated in a gas–liquid separator. Finally, bismutine was atomized in a quartz tube for the subsequent detection of bismuth by atomic absorption spectrometry. Different halide complexes of bismuth (namely, BiBr₄⁻, BiI₄⁻ and BiCl₄⁻) were tested for its pre-concentration, being the chloride complexes which produced the best results. Therefore, a concentration of 0.3 mol l⁻¹ of HCl was added to the samples and calibration solutions. A linear response was obtained between the detection limit (3σ) of 0.225 and 80 μg l⁻¹. The R.S.D.% (n = 10) for a solution containing 50 μg l⁻¹ of Bi was 0.85%. The tolerance of the system to interferences was evaluated by investigating the effect of the following ions: Cu²⁺, Co²⁺, Ni²⁺, Fe³⁺, Cd²⁺, Pb²⁺, Hg²⁺, Zn²⁺, and Mg²⁺. The most severe depression was caused by Hg²⁺, which at 60 mg l⁻¹ caused a 5% depression on the signal. For the other cations, concentrations between 1000 and 10,000 mg l⁻¹ could be tolerated. The system was applied to the determination of Bi in urine of patients under therapy with bismuth subcitrate. The recovery of spikes of 5 and 50 μg l⁻¹ of Bi added to the samples prior to digestion with HNO₃ and H₂O₂ was in satisfactory ranges from 95.0 to 101.0%. The concentrations of bismuth found in six selected samples using this procedure were in good agreement with those obtained by an alternative technique (ETAAS). Finally, the concentration of Bi determined in urine before and after 3 days of treatment were 1.94 ± 1.26 and 9.02 ± 5.82 μg l⁻¹, respectively.     

Etude vibrationnelle du fluorure hydrogenodifluorure de baryum BaF(HF2)

Infrared and Raman spectra of the BaF(HF₂) crystal and its 10 and 50% deuterated derivatives at 300 and 90 K have been investigated in the 4000 to 20 cm⁻¹ range. An assignment of internal and lattice vibrations has been proposed. Vibrational spectra are consistent with a centrosymmetric P2₁/m space group and Z=2. They show that the (FHF)⁻ ion is not centrosymmetrical, in spite of a short F…F distance; a force field calculation has been performed in order to determine the F---H and H…F distances, which are equal to 1.08 and 1.20 Å, respectively, in agreement with the ¹H and ¹⁹F NMR data. The ν₃(H)/ν₃(D) isotope frequency ratio indicates a negative or zero isotope effect on the F…F distance, which is observed for the first time for a strong asymmetric hydrogen bond.     

Observation and rovibrational analysis of the ν2 band of HCN–HCl

The high-resolution infrared absorption spectrum of an equilibrium mixture of HCN and HCl in a static gas long-path absorption cell is recorded in the 2500–2900 cm⁻¹ spectral region at 205 K. The spectrum shows rovibrational structure which has the typical appearance of a parallel band of a linear molecule and is assigned to the intramolecular H–Cl stretching vibration band ν₂ of the linear HCN–H³⁵Cl heterodimer. The rovibrational analysis of the band yield a band origin ν₀ of 2779.0968(12) cm⁻¹ together with a value for the upper-state rotational constant B′ of 0.067722(2) cm⁻¹. The observed red shift of 107 cm⁻¹ for the ν₂ band of HCN–H³⁵Cl relative to the H–Cl stretching vibration band of monomer H³⁵Cl is in excellent agreement with results from the MP2/6−311++G** level of theory. The value of the upper-state rotational constant shows that the intermolecular hydrogen bond shortens by 0.022 Å upon intramolecular vibrational excitation of the ν₂ mode.     

A new chelating sorbent for metal ion extraction under high saline conditions

A new chelating polymeric sorbent was developed by functionalizing Amberlite XAD-16 with 1,3-dimethyl-3-aminopropan-1-ol via a simple condensation mechanism. The newly developed chelating matrix offered a high resin capacity and faster sorption kinetics for the metal ions such as Mn(II), Pb(II), Ni(II), Co(II), Cu(II), Cd(II) and Zn(II). Various physio-chemical parameters like pH-effect, kinetics, eluant volume and flow rate, sample breakthrough volume, matrix interference effect on the metal ion sorption have been studied. The optimum pH range for the sorption of the above mentioned metal ions were 6.0–7.5, 6.0–7.0, 8.0–8.5, 7.0–7.5, 6.5–7.5, 7.5–8.5 and 6.5–7.0, respectively. The resin capacities for Mn(II), Pb(II), Ni(II), Co(II), Cu(II), Cd(II) and Zn(II) were found to be 0.62, 0.23, 0.55, 0.27, 0.46, 0.21 and 0.25 mmol g⁻¹ of the resin, respectively. The lower limit of detection was 10 ng ml⁻¹ for Cd(II), 40 ng ml⁻¹ for Mn(II) and Zn(II), 32 ng ml⁻¹ for Ni(II), 25 ng ml⁻¹ for Cu(II) and Co(II) and 20 ng ml⁻¹ for Pb(II). A high preconcentration value of 300 in the case of Mn(II), Co(II), Ni(II), Cu(II),Cd(II) and a value of 500 and 250 for Pb(II) and Zn(II), respectively, were achieved. A recovery of >98% was obtained for all the metal ions with 4 M HCl as eluting agent except in the case of Cu(II) where in 6 M HCl was necessary. The chelating polymer showed low sorption behavior to alkali and alkaline earth metals and also to various inorganic anionic species present in saline matrix. The method was applied for metal ion determination from water samples like seawater, well water and tap water and also from green leafy vegetable, from certified multivitamin tablets and steel samples.     

Nicotine derivative optode membrane with nonactin as ionophore

Plasticised poly(vinyl chloride) optode membrane incorporated with nonactin as ionophore, ETH 5294 as H⁺-selective chromoionophore and potassium tetrakis(4-chlorophenyl)borate as anionic site, was used as a reversible sensing device for indirect determination of nicotine. Nicotine was extracted from cigarette samples and converted to its bromoethane derivative (ND⁺Br⁻) by reacting with a solution of bromoethane in ethanol. ND⁺Br⁻, in a solution of Tris (hydroxymethyl)aminomethane–HCl buffer, was extracted into the bulk of the optode membrane and subsequently caused changes in optical absorption of the sensing layer. The pH effect, response mechanisms, response behaviour, response time, dynamic working range, detection limit, sensitivity and selectivity were discussed in detail.     

Selective potentiometric determination of nitrite ion using a novel (4-sulphophenylazo-)1-naphthylamine membrane sensor

A novel polymeric membrane sensor sensitive to (4-sulphophenylazo-)1-naphthylamine (SPAN) based on the use of tris(bathophenanthroline) Ni(II)–SPAN ion pair as an ion exchanger in plasticised PVC membrane is described. The sensor exhibits a linear calibration plot with near-Nernstian anionic slope of −55.0±0.3 mV log[SPAN]⁻¹ over the concentration range 10⁻⁶–10⁻² mol l⁻¹ at pH 7. The sensor shows working range over the pH 6–8, response time of 20 s for 10⁻⁵ mol l⁻¹ and operational lifetime of 8 weeks. The sensor is used for quantification of micro quantities of nitrite ion by a prior conversion into the more lipophilic SPAN ion, which is measured with adequate sensitivity, and high selectivity using SPAN sensor. Validation of the method according to the quality assurance standards shows good performance characteristics. The sensor is satisfactory utilised for potentiometric determination of nitrite ion in wastewater samples and meat products. The results are favourably compared with data obtained using the standard spectrophotometric procedure involving the same reaction.