纤维增强混凝土材料的界面剪应力分布研究

针对纤维与混凝土界面的破坏过程,提出了几种简化的粘结-滑移本构模型,以双线性局部粘结-滑移本构模型为基础,在受力平衡和变形协调的基本原理基础上,推导了纤维脱粘过程中界面剪应力的解析解.采用弹簧粘结单元,通过数值方法模拟了纤维与混凝土之间的粘结-滑移过程,给出了纤维与混凝土界面脱粘过程中界面剪应力的分布、变化情况.对解析解、有限元计算结果和试验结果之间的差异进行了对比分析,验证了简化模型的合理性和有效性.     

Improved theoretical solution for interfacial stresses in concrete beams strengthened with FRP plate

In this paper, an improved theoretical interfacial stress analysis is presented for simply supported concrete beam bonded with a FRP plate. The adherend shear deformations have been included in the present theoretical analyses by assuming a linear shear stress through the thickness of the adherends, while all existing solutions neglect this effect. Remarkable effect of shear deformations of adherends has been noted in the results. Indeed, the resulting interfacial stresses concentrations are considerably smaller than those obtained by other models which neglect adherent shear deformations. It is shown that both the normal and shear stresses at the interface are influenced by the material and geometry parameters of the composite beam. This research is helpful for the understanding on mechanical behavior of the interface and design of the FRP–RC hybrid structures.     

A three-parameter elastic foundation model for interface stresses in curved beams externally strengthened by a thin FRP plate

Externally bonding of fiber reinforced polymer (FRP) plates or sheets has become a popular method for strengthening reinforced concrete structures. Stresses along the FRP–concrete interface are of great importance to the effectiveness of this type of strengthening because high stress concentration along the FRP–concrete interface can lead to the FRP debonding from the concrete beam. In this study, we develop an analytical solution of interface stresses in a curved structural beam bonded with a thin plate. A novel three-parameter elastic foundation model is used to describe the behavior of the adhesive layer. This adhesive layer model is an extension of the two-parameter elastic foundation commonly used in existing studies. It assumes that the shear stress in the adhesive layer is constant through the thickness, and the interface normal stresses along two concrete/adhesive and adhesive/FRP interfaces are different. Closed-form solutions are obtained for these two interfacial normal stresses, shear stress within the adhesive layer, and beam forces. The validation of these solutions is confirmed by finite element analysis.     

Finite element analysis of interfacial stresses in FRP–RC hybrid beams

The interfacial stresses in fiber reinforced plastic (FRP)–reinforced concrete (RC) hybrid beams were studied by the finite element method. The mesh sensitivity test shows that the finite element results for interfacial stresses are not sensitive to the finite element mesh. The finite element analysis then is used to calculate the interfacial stress distribution and evaluate the effect of the structural parameters on the interfacial behavior. It is shown that both the normal and shear stresses at the interface are influenced by the material and geometry parameters of the composite beam. This research is helpful for the understanding on mechanical behavior of the interface and design of the FRP–RC hybrid structures.     

接触面损伤演化过程的数值模型

结合接触面在细观尺度上的非均匀性及其损伤演化规律,提出了一种可以考虑接触面损伤演化过程的数值模型.数值模拟得到的剪切应力-剪切位移关系表明:随着剪切位移的增加,接触面上产生的损伤单元导致曲线斜率逐渐降低;当接触面被完全剪断后,模型中的剪切应力出现了一定程度的下降,此后的剪应力在摩擦力的作用下基本保持不变.模型所能承受的...     

Debonding of FRP-plated reinforced concrete beam,a bond-slip analysis. I. Theoretical formulation

External bonding of FRP plates or sheets has emerged as a popular method for strengthening reinforced concrete. Debonding along the FRP–concrete interface can lead to premature failure of the structure. In this study, a bond-slip model is established to study the interface debonding induced by a flexural crack in a FRP-plated concrete beam. The reinforced concrete beam and FRP plate are modeled as two linearly elastic Euler–Bernoulli beams bonded together through a thin layer of FRP–concrete interface. The interface layer is essentially modeled as a large fracture processing zone of which the stress–deformation relationship is described by a nonlinear bond-slip model. Three different bond-slip models (bi-linear, triangular and linear-damaging) are used. By dividing the debonding process into several stages, governing equations of interfacial shear and normal stresses are obtained. Closed-form solutions are then obtained for the interfacial shear and normal stresses and the deflection of the beam in each stage of debonding. In such a way, the proposed model unifies the whole debonding process, including elastic deformation, debonding initiation and growth, into one model. With such a superior feature, the proposed model provides an efficient and effective analytical tool to study FRP–concrete interface debonding.     

模型复合材料弹塑性界面应力分析

由纤维增强弹塑性基体所产生的界面具有弹塑性力学行为。考虑到一般材料的塑性变形都遵循幂硬化规律,对模型复合材料的界面进行弹性和应变硬化状态下的变形规律及其应力分析。以纤维拔出试验为研究模型,将界面分成弹性区和塑性区。利用界面应力剪滞理论,分别建立弹性区和塑性区的界面力学基本方程。选择适当的位移函数满足基本方程及埋入纤维的边界条件,再按位移函数求出弹性区和塑性区的界面剪应力。推导出平均界面剪应力与纤维     

碳纤维布与钢板复合加固梁剥离破坏研究

通过12根碳纤维布与钢板复合加固钢筋混凝土梁的抗弯性能研究,结果表明复合加固方式能有效地改善被加固构件的受力性能,但常由于复合加固层的剥离可能导致加固效果的降低。复合加固层与被加固构件之间的剥离是由于薄弱截面在剪应力及正应力的集中作用下而产生的,文中对复合加固层与混凝土之间的粘结剪应力及剥离正应力的计算公式分别进行推导,并进一步对碳纤维布与钢板复合加固的剥离机理进行分析,为工程应用提供依据。     

Loss of adhesion at the tip of an interface crack

A model is constructed to analyze adhesive bond failure at the tip of an interface crack. The model is based on the assumption that there are zones of bounded cohesive tensile and shear stresses near a crack tip. Within the context of certain broad a-priori assumptions on the distributions of certain stress and displacement components in the cohesive zones, the requirement thatall stresses in the two materials remain bounded provides a method to compute the specific details for these zones. It is assumed that bond failure occurs when the extension of the bond fiber at the crack tip exceeds a critical value. For an interface crack in a uniform tension field computations for two alternate formulations suggest that this failure criterion is independent of the precise distribution of the cohesive stresses, but rather depends only upon their averaged values. Combined loading with a dominant tensile component has also been analyzed. If the critical extension of bond fibers and the maximum value of the cohesive tensile stress are known, the model provides the maximum allowable interface stresses for given crack dimension and material parameters.     

Debonding analysis of FRP–concrete interface between two balanced adjacent flexural cracks in plated beams

A cohesive interface modeling approach to debonding analysis of adhesively bonded interface between two balanced adjacent flexural cracks in conventional material (e.g., concrete or wood) beams strengthened with externally bonded FRP plates is presented. Both the strengthened beam and strengthening FRP are modeled as two linearly elastic Euler–Bernoulli beams bonded together through a thin adhesive layer. A bi-linear cohesive model, which is commonly used in the literature, is adopted to characterize the stress-deformation relationship of the FRP–concrete interface. Completely different from the single-lap or double-shear pull models in which only the axial pull force is considered, the present model takes the couple moment and transverse shear forces in both the substrates into account to study the second type of intermediate crack-induced debonding (IC debonding) along the interface. The whole debonding process of the FRP–concrete interface is discussed in detail, and closed-form solutions of bond slip, interface shear stress, and axial force of FRP in different stages are obtained. A rotational spring model is introduced at locations of the two adjacent flexural cracks to model the local flexibility of the cracked concrete beam, with which the relationship between the local bond slip and externally applied load is established and the real bond failure process of the FRP-plated concrete beam with the increasing of the externally applied load is revealed. Parametric studies are further conducted to investigate the effect of the thickness of adhesive layer on the bond behavior of FRP–concrete interface. The present closed-form solution and analysis on the local bond slip versus applied load relationship for the second type of IC debonding along the interface shed light on the bond failure process of structures externally strengthened with FRP composite plates and can be used effectively and efficiently to predict ductility and ultimate load of FRP-strengthened structures.     

钢筋混凝土开裂角软化薄膜模型

开裂角介于固定角和转动角之间,是裂缝实际的开展方向角.通过建立平衡方程、协调方程、钢筋和混凝土本构方程、泊松比效应系数方程,提出了钢筋混凝土开裂角软化薄膜模型,该模型考虑了拉应变与压应变的相互作用.本文还给出从应力到应变的计算方法,与传统从应变到应力的计算方法相比,该方法无须进行反复试算,计算简便.通过与8块钢筋混凝土薄板试验结果的比较,验证了所提出开裂角软化薄膜模型及其算法的正确性.     

On the relationship between the work of adhesion and the critical shear stress for the onset of flow instabilities

The relationship between the critical shear stress for the onset of flow instabilities and the work of adhesion at the interface has been evaluated experimentally for a series of polyolefins on several steels, brasses, and coated steels. The critical shear stress was considerably affected by the chemical nature of the die. Low-surface-energy materials were found to produce smooth extrudates presumably by inducing slippage at the wall. Steel, tungsten carbide, and brass surfaces promoted sharkskin defect at shear stresses above the first critical shear stress. A linear relationship between the critical shear stress and the work of adhesion was found to be valid for values of work of adhesion smaller than approximately 30 mN/m. This indicates that slippage occurs due to a breakdown of the adhesion at the interface. For values of work of adhesion greater than approximately 30 mN/m a stronger interaction at the interface may induce a cohesive failure at the interface and subsequently, extrudate distortions.     

On the existence of stress concentrations in loaded bodies made of polycrystalline materials

We study the character of stress distributions near the corner point of the interface between the two joined crystals. The interface forms a dihedral angle. The joined crystals have a cubic symmetry and consist of the same material. They have a single common principal direction of elasticity, which is parallel to the edge of the dihedral angle. The other principal directions do not coincide and are oriented arbitrarily.In the framework of elasticity, we consider problems of out-of-plane and plane strain of the twocrystal. We show that, in the case of longitudinal shear in the direction of the common principal axis of elasticity, there is no stress concentration near the corner point of the interface between the two joined crystals.For the case of plane strain in which all displacements and strains occur only in the planes perpendicular to the common principal direction, we use separation of variables to construct the characteristic equation that determines the stress concentration degree and find the roots of this equation, which determine the order of singularities of the stresses.     

脆性损伤材料裂纹尖端的局部解

本文利用Mazars和Lemaitre提出的混凝土脆性损伤模型,求得了裂纹尖端应力、应变及损伤的局部解.对手Ⅲ型及不可压缩平面应变Ⅰ型裂纹,其尖端场的构造和理想塑性材料相类似.指出由于丧失了应力全连续条件,从而损伤边界不能由局部解定出.     

Nonlinear analysis of beam–column joints using softened truss model

The aim of this study is to expand the application of the nonlinear softened truss model for membrane elements on beam–column joints. The softened truss model employs three equations for equilibrium, three for compatibility and four equations for the constitutive laws of materials. The constitutive equations for both the concrete and steel are based on the actually observed stress–strain relationships. The model has three important attributes. The first is the nonlinear association of stress and strain. The second, and conceivably more noteworthy, is the softening of concrete in compression due to tensile strains in the perpendicular direction. The third is that the influence of the concrete tensile stresses between cracks on the average stress–strain relationship for reinforcing steel and the influence of orthogonal tensile stresses on the compression stress–strain relationship for concrete can be considered in the model. For beam–column joints, one of the most important factors influencing the behaviour is certainly the bond conditions of the beam bars. In this study, the softened truss model is expanded to take into account the influence of this important factor into account. In the revised version of the model, full strain compatibility does not exist between the steel reinforcement and the surrounding concrete and thus the factors influencing the bond-slip between concrete and reinforcement is adequately considered. The improved softened truss model is applied on 51 exterior beam–column joint tests. It is apparent from the results that the revised model gives very accurate predictions of the shear strength of joints and is an improvement on the existing version of the model proposed by Hsu.     

Linear coupled bending and extension of an unbalanced bonded repair

An unbalanced repair is a composite patch bonded to one side of a cracked structure for the purpose of preventing or reducing damage growth in the substrate. A single-sided repair offsets the load path within the structure, inducing out-of-plane bending. This bending increases the stress intensity in the underlying crack and causes adhesive peel stresses and bending of the repair which can, relative to a repair that is restrained against bending, lead to early failure. In this article the authors correct the analysis of Wang and Rose [Wang, C.H., Rose, L.R.F., 1997. On the design of bonded patches for one-sided repair. In: Proceedings of the 11th International Conference on Composite materials, Gold Coast, Australia, vol. 5, pp. 347–356] developed by using an energy analysis of a single-sided or unbalanced repair applied to a very long-crack, to comply with Maxwell’s reciprocal theorem and to account for transverse normal and shear stresses at the crack tip and the accompanying shear deflections. The authors then develop closed-form equations useful for bonded composite repair design and damage tolerance assessment of cracks of arbitrary length by developing a new method for interpolation between this long-crack limit and a short-crack limit based on the stress intensity and crack face displacements for an unreinforced crack. The interpolation method is then tested against an advanced line-spring model that has been created by using a 6th order generalized plane strain plate formulation in extension and a new 8th order formulation in bending, thus allowing for the inclusion of transverse shear and normal stresses. The closed-form equations are found to be accurate when compared to the line-spring model, and to provide reasonable results when compared to a three-dimensional finite element model of a bonded repair. Inaccuracies are shown to exist principally in the determination of the nominal stresses in the vicinity of the crack.     

胶结砂砾石层面直剪试验及破坏行为细观研究

本文采用宏观试验和细观模拟相结合的方法研究胶结砂砾石层面在剪切过程中的破坏行为．首先进行了不同法向应力作用下的胶结砂砾石层面直剪试验,获得了不同的剪切面破坏特征：随着法向应力的不断增加,剪切破坏面凹凸起伏程度、骨料脱落现象越发明显．其次为了深入探究层面破坏现象,按照室内试验采用的骨料级配粒径建立细观颗粒数值模型,结合物理试验对模型进行参数标定,并进行数值模型的层面直剪模拟和细观分析．结果表明,数值模型可以再现宏观直剪试验层面破坏特征;法向应力越大,层面区域颗粒发生错动和翻转的数量越多;层面破坏方式为颗粒间的张拉和剪切混合破坏,裂隙均集中在层面位置,随着法向应力的增加,裂隙的集中区域逐渐由“面”向“带”转变．     

Numerical validation of the shear compression specimen. Part I: Quasi-static large strain testing

The shear compression specimen (SCS), which is used for large strain testing, is thoroughly investigated numerically using three-dimensional elastoplastic finite element simulations. In this first part of the study we address quasi-static loading. A bi-linear material model is assumed. We investigate the effect of geometrical parameters, such as gage height and root radius, on the stress and strain distribution and concentration. The analyses show that the stresses and strains are reasonably uniform on a typical gage mid-section, and their average values reflect accurately the prescribed material model. We derive accurate correlations between the averaged von Mises stress and strain and the applied experimental load and displacement. These relations depend on the specimen geometry and the material properties. Numerical results are compared to experimental data, and an excellent agreement is observed. This study confirms the potential of the SCS for large strain testing of material.