抽运光对激光束空间分布影响程度的估算方法研究

为便于评价两种光场空间分布之间的偏离程度，引入一个数学参数δ进行研究。将该参数应用到谐振腔内分析了抽运光空间分布对基模振荡光光束质量的影响。这种影响主要表现为：若抽运光在激光介质中引起非均匀的增益分布，基模振荡光将偏离高斯分布。利用δ参数对这种影响的程度进行了定量估算。定量研究表明：δ参数可以直观地反映泵浦光分布对激光器光束质量的影响程度，而且在激光器的设计中δ参数的大小可衡量泵浦光分布的优劣。对于端面泵浦二极管泵浦固体激光器（DPL），稳恒运转下最理想的抽运光分布形式是高斯型抽运光，其半径等于谐振腔的基模高斯振荡光半径。     

微片激光器模式匹配

分析纵向泵浦微片激光器模式的模型,给出了泵浦光参数和腔模光参数如何影响激光器输出光强的大小,通过数值计算可得出最佳模式匹配.     

LDA侧面泵浦固体激光器泵浦结构参数优化

为LDA侧面泵浦Nd∶YAG棒状固体激光器的优化设计、参数选取及后续试验提供了理论依据和参考,建立了环形侧面泵浦棒状介质泵浦光场分布数值计算模型,研究了LDA侧面泵浦固体Nd∶YAG激光器泵浦光场的分布特点。模拟分析了LDA的bar间距、玻璃管厚度、激光晶体半径等几个主要泵浦结构参数对泵浦光场分布的影响。通过对不同泵浦参数下泵浦光分布特性的数值计算,优化了LDA侧面泵浦固体激光器的泵浦结构参数,优化后的仿真结果表明:在泵浦距离为2 mm条件下,晶体直径为4 mm,玻璃管套筒厚度为1 mm,冷却水层厚度为1 mm时,泵浦光在晶体中心处强度相对值为40.8%,在晶体轴心附近分布比较均匀,且均匀分布区域相对较大。     

自锁模Cr:LiSAF激光器的特性研究

本文分析上转换过程及荧光热猝灭效应对Cr:LiSAF激光器的泵浦阈值和输出功率的影响,由此得出Cr:LiSAF激光器特别适合低功率泵浦.分析了三镜腔结构的特性,选择了腔的较佳参数,实现了在750mW的氩离子激光泵浦下三镜腔Cr:LiSAF激光器的自锁模运转.     

激光二极管端面泵浦的单频固体激光器的理论研究

给出了激光二极管端面泵浦的驻波激光器单频运转时的最大泵浦功率与腔参数和激光介质参烽之间的简单函数关系，对于单频激光器的设计具有实际指导意义。     

Excimer Laser Pumped Tunable Picosecond Dye Lasers

研究了可调谐淬灭式染料激光器的染料浓度和泵浦能量对淬灭效果的影响，并且研究了它的调谐范围。对于308 nm XeCl准分子激光泵浦淬灭式香豆素498染料激光器，得到了一些具体的参数。     

猝灭式染料激光器理论研究

理论上研究了由准分子激光泵浦的猝灭式染料激光器的猝灭机理，对于一些具体的泵浦情况，通过激光速率方程理论上探讨了激光器的猝灭效果，并且对激光器的一些重要参数进行了一些研究。     

F－P有源微片激光腔横模场分析

分析在纵向泵浦微片激光器中Fox-Li迭代法适用条件,通过数值计算,得出在不同泵浦参数下平平F-P有源腔微片激光器的横模结构。     

高功率半导体泵浦固体激光器输出特性的研究

通过实验详细测量了水温、工作电流对二极管激光器发射波长的影响;采用光线追踪法模拟计算出在不同泵浦参数下半导体泵浦光在NdYAG棒内的分布情况,得到了圆周上泵浦模块的个数,泵浦光发散角等因素对泵浦光分布均匀性的影响.采用直接泵浦方式,分别设计了二种不同功率水平的半导体泵浦的NdYAG固体激光器聚光腔,得到了170和800 W的输出功率,并对激光器的输出特性进行详细测量,最大光-光转换效率达37%,电-光转换效率约为16%.     

纵向泵浦的1.34μm Nd:YVO4平凹腔型DPSL器件

报道了激光二极管泵浦的Nd:YVO4激光器,分析了激光器的各项参数.在泵浦功率为7.06W时,获得1.34μm激光输出功率2.008W,光-光转换效率达28.4%.     

Theoretical and experimental investigations of a diode-pumped high-power continuous-wave 912 nm Nd:GdVO4 laser operation at room temperature

Based on the rate equation of Nd³⁺-doped quasi-three-level lasers, a theoretical model of diode-end-pumped continuous-wave 912 nm Nd:GdVO₄ laser is presented. Lasing threshold and slope efficiency considering reabsorption effect are calculated and analyzed. It is found that the output performance of 912 nm laser operating at room temperature is influenced remarkably by the reabsorption loss and spatial distribution of the pump beam and laser beam. In experiments, the output power and average slope efficiency of 912 nm laser were investigated under different conditions. After optimization at the parameters of laser medium, working temperature and spatial distribution of the pump beam, up to 16.2 W continuous-wave 912 nm laser output was obtained at incident pump power of 67.0 W, with an average slope efficiency of 41.7%, to the best of our knowledge, this is the highest output power of diode-pumped 912 nm Nd:GdVO₄ laser by far.     

一种大面积高能激光光束参数的在线测量方法

 提出了一种大面积连续波高能激光光束参数的在线测量方法——环形光刀扫描测量法。该方法采用偏心安装的斜面环形光刀高速扫描反射，光电探测器阵列沿反射光圆周均匀布置探测，使得绝大部分被测激光沿原光路传播，只有少量取样光被反射到探测器阵列上。通过对采集得到的探测器响应信号进行空间映射计算和图像复原，得到激光束的光强分布参数。该方法可用于光束直径数百mm的高能激光光束测量，测量空间分辨率约2 mm，时间分辨率为30~50 ms。     

线阵激光二极管侧面抽运Nd∶YAG激光器特性研究

依据四能级系统速率方程 ,推导出了多横模振荡固体激光器输出与输入参量的关系。对二极管抽运固体激光器中线阵激光二极管三向对称侧面抽运结构 ,计算了抽运光强分布 ,并就激光器的阈值抽运功率、近阈值条件下的斜率效率、输出功率和光束质量等与抽运参量的关系 ,进行了数值计算。由计算结果看出 ,线阵激光二极管侧面抽运Nd∶YAG激光器中晶体半径和抽运光束腰半径是影响输出激光功率和光束质量的主要因素 ,并通过在谐振腔中加小孔选模 ,使光束质量得到明显改善。选择了一组三向侧面抽运结构参量进行了实验验证 ,实验结果与理论计算一致。     

非稳腔输出环状激光束的传输特性

本文从菲涅耳衍射积分公式出发研究了激光器非稳腔输出环状光束在空间的传输规律.由轴上光强的极值点位置给出了划分非稳腔传输空间的近场、中场和远场区域公式.理论计算结果表明,非稳腔输出端环状光束在中场区域激光能量逐渐向轴心方向转移,而在远场变为爱里型圆盘状光束的过程.在非稳腔脉冲TEA CO_2激光器上测得的实验结果与理论计算结果很好地符合.     

Analysis of temperature distributions in diode-pumped alkali vapor lasers

Assuming the pump light to be a Gaussian beam and considering the medium absorption, we establish the heat conduction model to describe the temperature distribution in diode-pumped alkali vapor lasers (DPALs) with two different pumping ways. Combining with the experimental parameters in cesium laser, the spatial temperature distribution picture, the longitudinal and the radial temperature distributions of two cesium lasers are obtained by numerical solving the model. Influences of the pump power, the beam waist and the absorption coefficient on the axial and the radial temperature distribution are calculated and compared for the two Cs lasers. The result suggests that Cs laser pumped by two laser diode arrays can improve the spatial temperature distribution condition and reduce the longitudinal temperature gradient, which is good for reducing the thermal effects and improving the output characteristics of DPALs.     

Generation of a fast-ion beam upon the interaction of a multiterawatt picosecond laser pulse with a solid target

The parameters of fast particles generated upon the interaction of 10¹⁹ W/cm² laser pulses with solid targets are studied. The spatial and energy parameters of fast ions are investigated. It is found that approximately 1–3% of the laser energy is transformed to the energy of mega-and submegaelectronvolt ions at laser pulse intensities ≥10¹⁸ W/cm². It is shown experimentally that an ion beam is directed perpendicular to the target surface. The analytic and numerical simulations agree with experimental results and predict the propagation of fast electrons in the mirror direction with respect to the incident laser beam and of ions perpendicular to the target. The theoretical calculations are compared with the experimental output and spectra of fast electrons and ions.     

激光二极管泵浦NYAB激光器的空间分布速率方程的研究

报道了用以描述激光二极管泵浦ＮＹＡＢ连续激光顺空间分布特性的非线性耦合的速率方程组，和以此方程组进行的理论计算，讨论了泵浦光和激光的空间分布、晶体的最佳长度、输出镜的最佳透过率对激光器输出的影响，给出了ＮＹＡＢ激光器设计的一些依据。     

基于液晶空间光调制器的激光束整形

采用相位混合算法(PMA)与平滑修正法相结合的混合算法,对激光发出的高斯光束进行整形,得到了均方误差和顶部不均匀度均明显降低的等光强分布。利用液晶空间光调制器(LCSLM)的相位调制特性,实现了对高斯光束的光束整形,获得了光强均匀分布的圆光束和矩形光束输出。得到的输出光束顶部不均匀度和均方误差都低于5%,能量集中度在90%以上。表明此方法是一种实时、可控和高效的激光束整形方法。     

超短脉冲激光光束被局域体全息光栅衍射的性质分析

利用二维耦合波理论,分析了超短脉冲激光光束被完全重叠型的局域体全息光栅衍射的时空变化性质,给出了衍射和透射脉冲激光光束沿光栅出射边界的强度时空分布。以LiNbO3晶体为例,数值研究了衍射光脉冲强度沿光栅出射边界的分布和脉冲波形的变化及光栅的总衍射效率受光栅二维尺寸、入射角度、光栅折射率调制度及入射脉冲的脉冲时域半峰全宽等条件的影响而变化的情况。与一维体全息光栅对超短脉冲激光光束衍射的性质,及此光栅对连续光衍射的性质作比较,给出了合理选择光栅参量及入射条件以在光栅出射边界上得到总衍射效率较大且分布较均匀的衍射光脉冲的方法。     

Propagation of a filamentary femtosecond laser beam with high intensities at an air-solid interface

The propagation of a filamentary laser beam at an air-glass surface is studied by setting the incident angle satisfying the total reflection condition. The images of the trajectory of the filamentary laser beam inside the sample and the output far-field spatial profiles are measured with varying incident laser pulse energies. Different from the general total reflection, a transmitted laser beam is detected along the propagation direction of the incident laser beam. The energy ratio of the transmitted laser beam depends on the pulse energies of the incident laser beam. The background energy reservoir surrounding the filament core can break the law of total reflection at the air-glass surface, resulting in the regeneration of the transmitted laser beam.