基于荧光内滤效应的锂离子荧光化学传器研究

报道了一种基于荧光内滤效应的荧光增强型锂离子光化学传感器,将荧光试剂、亲脂性pH指标剂和锂离子中性载体结合在增塑的ＰＶＣ膜中,Ｌi^ 与Ｈ^ 在膜相中的竞争萃取效应引起受亲脂性pH指示剂调制的敏感膜荧光值的变化,推导了有关理论关系式,研究了该传感器的响应特性,并对人工合成样品进行测试,结果较了满意。     

基于咔唑的分子内电荷转移分子聚集体对Ag+的比率荧光检测

以吡啶套索醚银离子络合基团为电荷受体,N-苯基咔唑为电荷给体,构筑分子内电荷转移共轭体系。咔唑基团的亲脂性可以增强分子在水介质中的疏水作用而形成分子聚集体。随着混合溶剂中水比例的上升,该分子呈现明显的丁达尔现象,荧光发射峰呈现先红移后蓝移的现象。在四氢呋喃-水(THF-H₂O,φ_H2O=87%)介质中,分子聚集体于428 nm处呈现较弱的荧光发射峰,随着溶液中Ag⁺浓度的增加,Ag⁺配合物在498 nm处的发射峰逐渐增强,该传感器分子聚集体可以对Ag⁺实现比率荧光检测,检出限0.337μmol/L。该传感器比率信号在0～0.7μmol/L范围内对Ag⁺具有较好的线性关系。     

双光子荧光探针

双光子吸收是指在强光激发下,介质分子同时吸收两个光子,从基态跃迁到两倍光子能量的激发态的过程。荧光显微成像是研究活体生物的重要工具,而最通常的细胞成像方法则是使用单光子激发荧光团的单光子显微成像。近红外光源激发的双光子荧光探针克服了单光子荧光探针的光漂白与光致毒而更适于生物检测与成像,为生命科学研究提供了更为锐利的工具。双光子荧光探针的作用机理包括分子内电荷迁移(ICT)、荧光共振能量迁移(FRET)、光诱导电子迁移(PET)与基团转换(GC) 4种方式。该文综述了双光子阳离子探针(Mg²⁺, Ca²⁺, Pb²⁺, Hg²⁺, Ag⁺, Fe³⁺, Zn²⁺, Na⁺, Cr³⁺)、双光子阴离子探针(F^-)、pH探针、双光子葡萄糖示踪器、双光子脂筏探针、双光子巯基探针、双光子半胱氨酸探针和双光子生物标记探针,以及双光子荧光探针在生物成像方面的应用,展望了双光子荧光探针的发展趋势与应用前景。     

罗丹明类钯离子荧光分子探针

将烯丙基结构引入到罗丹明螺环中, 合成了荧光增强型钯离子探针RPd4. RPd4表现出对Pd²⁺的专一选择性和对其它阳离子良好的抗干扰能力. 探针荧光强度随着Pd²⁺的加入逐渐增强, 并且在微摩尔级呈现良好的线性关系, 通过拟合计算得到对Pd²⁺的检出限为0.51 μmol/L. RPd4具有较低的pK_a值(3.81±0.02), 说明该探针可以在近中性pH范围内对Pd²⁺进行选择性识别. 该探针还可以提供比色及荧光两种方式对Pd²⁺进行可视化检测.     

稀土离子跨人血红细胞膜的荧光法研究

采用Fura-2荧光浓度指示剂对红细胞的稀土跨膜作用进行了系列研究.结果表明,稀土离子不能通过完整的红细胞膜进入细胞内.通过与离子载体实验相对照,发现细胞ATP耗竭后,低浓度的稀土离子(5×10^-6mol/L)不能跨膜进入ATP-耗竭红细胞.KCl去极化及加入电压依赖性钙通道刺激剂Bay-K8644对稀土离子的跨膜也没有促进作用.在Ca²⁺内流正常的情况下,低浓度稀土离子(5×10^-6mol/L)对钙离子内流无影响.增大稀土离子浓度到5×10^-4mol/L,用显微镜观察此时红细胞已开始溶血.在模拟胞内离子组分的缓冲液中(pH=7.05),比较了La³⁺,Eu³⁺和Ca²⁺对Fura-2的敏感程度.此条件下Fura-2对La³⁺和Eu³⁺的检测限分别为10-12和10-14mol/L,对Ca²⁺的检测限为10-8mol/L,并测得Fura-2-La³⁺(Eu³⁺)的络合比为1∶1,表观离解常数为1.7×10^-12和4.95×10^-14mol/L,表明用此法检测稀土离子跨膜行为相当灵敏有效.     

香豆素衍生物荧光传感器对Zn2+的识别及细胞成像

制备了基于香豆素衍生物的荧光传感器CANQ,其可选择性地识别Zn²⁺离子。通过NMR、MS、荧光光谱等技术研究了传感器的结构及荧光性能。传感器CANQ对Zn²⁺离子具有显著的荧光增强响应,且响应速度快、选择性高、生物相容性好,可用于MCF?7细胞中Zn²⁺离子的成像。     

基于1,8-萘酰亚胺与罗丹明B间荧光共振能量转移的高选择性Hg2+比率荧光探针

以罗丹明B与1,8-萘二甲酰亚胺反应合成了1个高选择性Hg²⁺比率荧光探针(RN). 在甲醇/乙腈/4-羟基哌嗪乙磺酸缓冲溶液(pH=7.2, 体积比8:1:1)中, RN对Hg²⁺具有比色和比率荧光双重响应. 加入Hg²⁺后, RN的紫外-可见光谱在约556 nm处产生强吸收, 溶液由浅绿色变为橙色, 其它金属离子对RN的紫外-可见光谱几乎无影响. 无Hg²⁺存在时, RN的荧光光谱在540 nm处出现萘二甲酰亚胺荧光团的特征峰; 加入Hg²⁺后, 540 nm处的发射带逐渐消失, 同时在580 nm附近产生强荧光, 荧光颜色从绿色变为橙色. 这归因于从萘酰亚胺到开环罗丹明B的荧光共振能量转移(FRET), 探针RN对Hg²⁺的比率荧光响应具有高选择性, 不受其它共存金属离子的干扰.     

荧光素-层状双金属氢氧化物复合体的发光性能及对Fe3+的荧光识别

采用离子交换法合成了FLN/OS-LDH复合体(FLN: 荧光素, OS: 1-辛烷磺酸钠, LDH: 镁铝型层状双金属氢氧化物), 并研究了其光致发光和对Fe³⁺的识别性能. 固态时, FLN不发光, 而FLN/OS-LDH复合体呈黄绿色荧光(发射波长为565 nm), 是荧光素(FLN)的特征发射光. 在甲酰胺(FM)中可将该复合体方便剥离为胶状悬浮液, 其发射波长发生蓝移, 为绿光发射(531 nm). 研究了复合体剥离液对金属离子的荧光识别特性, 发现其对Fe³⁺的选择性识别能力很强, 远优于其它离子(Mg²⁺, Ni²⁺, Co²⁺, Cu²⁺, Zn²⁺, Pb²⁺, Cd²⁺和Hg²⁺). 该复合体与Fe³⁺结合发生荧光猝灭现象, 可将其用作检测Fe³⁺的荧光传感器. Fe³⁺检测限为1.27×10^-7 mol/L, 猝灭常数(K_sv)为3.44×10² L/mol.     

一种裸眼和荧光双通道快速检测Hg2+的探针及其多种应用(英文)

设计并合成了一种在二甲基亚砜(DMSO)/磷酸缓冲溶液(PBS)(V∶V=5∶5,pH=10.17)中识别Hg²⁺的荧光探针HMI-Hg²⁺.HMI-Hg²⁺通过荧光信号增强识别Hg²⁺,并且溶液颜色在几秒钟内发生改变.光谱实验证实了该探针对Hg²⁺具有高选择性和高灵敏度,检测限为0.22μmol/L.HMI-Hg²⁺在水样和海鲜样品(鱼、虾和扇贝)中具有出色的检测效果.此外,HMI-Hg²⁺可用于在MCF-7细胞中对Hg²⁺进行成像,并具有线粒体靶向能力.     

上转换荧光响应性复合纳米凝胶的制备及荧光能量传递行为

采用水热法合成NaYF₄∶Yb³⁺,Er³⁺稀土纳米晶, 再经3-苄基三硫代碳酸酯基丙酸(BSPA)修饰, 制得功能化纳米晶体; 以罗丹明6G(R6G)为母体荧光染料, 经一系列反应合成了乙烯基功能化单体罗丹明6G酰基邻羧基苯甲肼腙(R6GHA); 将功能化纳米晶体与R6GHA构成荧光共振能量传递(FRET)的“给体/受体”对, 通过可逆加成断裂链转移(RAFT)聚合和“点击化学”反应, 合成具有多重响应性复合荧光纳米凝胶NaYF₄∶Yb³⁺,Er³⁺/PNIPAm-co-R6GHA. 采用TEM, XRD, FTIR和DSC对产物的微观结构进行了表征; 采用上转换荧光光谱(PL)研究了该复合纳米凝胶对pH值、 环境温度和不同金属离子的荧光响应行为, 并对相关机理进行了探讨. 结果表明, 环境温度变化对复合纳米凝胶的荧光发射具有显著影响, 且该复合纳米凝胶对Hg²⁺具有选择性荧光响应; 在H⁺或Hg²⁺作用下, 复合纳米凝胶中纳米晶和R6GHA之间会发生荧光共振能量传递; 通过纳米凝胶中纳米晶与R6GHA特征荧光发射峰比率的变化, 实现对Hg²⁺的检测.     

Iodide-selective polymeric membrane electrode based on copper(Ⅱ) bis(N-2-bromophenylsalicyldenaminato) complex

A PVC membrane electrode based on copper（Ⅱ） bis（N-2-bromophenylsalicyldenaminato） as ionophor was prepared.The ion selective electrode was tested by inorganic anions and showed a good selectivity for iodide ion.This sensor exhibited Nernstian behavior with a slope of—57.8 mV per decade at 25℃.The proposed electrode showed a linear range from 1.0×10⁵ to 1.0×10^-1 mol/L with a detection limit of 5.0×10^-6 mol/L.The electrode response was independent of pH in the range of 3.0- 10.0.The proposed sensor was applied to determine the iodide in water and antiseptic samples.     

Chemiluminescence Sensor for the Determination of Hydroxylamine by Electrostatically Immobilizing Luminol and Periodate

IntroductionAnalytical methods based on chemilumi-nescence( CL ) reactions have received considerableattention for theirapplication in various fields,ow-ing to their extremely high sensitivity along withother advantages such as wide linear dynamicrange,simple instrumentation,easy miniaturiza-tion and coupling to various separation tech-niques[1— 6] .CL sensors have been developed for be-ing used as the continuous and real- time monitorsof inorganic,organic,biological and pharmaceuti-cal comp…     

Selective recognition of monohydrogen phosphate by fluorescence enhancement of a new cerium complex

Bis(8-hydroxy quinoline-5-solphonate) cerium(III) chloride (Ce(QS)(2)Cl) (L) was synthesized and then used as a novel fluorescent sensor for anion recognition. Preliminarily study showed that fluorescence of L enhanced selectively in the presence of HPO(4)(2-) ion. This enhancement is attributed to a 1:1 complex formation between L and HPO(4)(2-) anion. The association constant of 1:1 complex of L-HPO(4)(2-) was calculated as 3.0×10(6). Thus, L was utilized as a basis for a selective detection of HPO(4)(2-) anion in solution. The linear response range of the proposed fluorescent chemo-sensor covers a concentration range of HPO(4)(2-) from 3.3×10(-7) to 5.0×10(-6) mol L(-1) with a detection limit of 2.5×10(-8) mol L(-1). L showed selective and sensitive fluorescence enhancement response toward HPO(4)(2-) ion in comparison with I(3)(-), NO(3)(-), CN(-), CO(3)(2-), Br(-), Cl(-), F(-), H(2)PO(4)(-) and SO(4)(2-) ions. It was probably attributed to the higher stability of the inorganic complex between HPO(4)(2-) ion and L. The method was successfully applied for analysis of phosphate ions in some fertilizers samples.     

Studies on Non－potentiometric Piezoelectric Sensor System for Determination of Vitamin B1

A piezoelectric sensor responsive to vitamin B1 was fabricated based on the vitamin B1-tetraphenylborate ion pair. The general performance characteristics of the sensor are presented here. The proposed sensor showed a wide working pH range, a good sensitivity and selectivity. The response range is between 1.0×10-7-4.9×10-5 mol/L with a detection limit of 8×10-8 mol/L at pH 4.0. The selectivity should be attributed to the preferential adsorption of the component ion on the membrane/solution interface. The adsorption behavior of vitamin B1 on the crystal surface was investigated with a quartz crystal impedance(QCI) system.     

利用salen型荧光探针测定Cr3+

研究了salen型席夫结构的荧光探针N,N’-二(2-羟基-1-萘甲醛)-l,2-苯二胺(NAPPDIH)对Cr3+的响应。Cr3+能够使该探针的荧光猝灭。研究表明,在pH3.5(乙酸胺-盐酸)和DMSO/H2O(V/V,8:2)的条件下,8.0×10-6 mol/L的Cr3+可以导致NAPPDIH 65%的荧光猝灭。并且,Cr3+的浓度在5.0×10-7～8.0×10-6 mol/L的范围内,与荧光强度的变化值呈良好的线性关系,检出限为3.7×10-7 mol/L。方法可用于直接检测水样中的Cr3+。     

基于荧光内滤效应的荧光增强型钠离子光纤传感器

在吸收型钠离子光化学传感器的敏感膜中加入合适的荧光试剂,应用荧光内滤效应研制成的荧光增强型光纤传感器,在测量灵敏度和抗背景干扰能力方面均有较大的改善,对血清和矿泉水样品中的钠离子含量进行了分析,获得了满意的结果。     

Electrochemical oxidation behavior of colchicine on a graphene oxide-Nafion composite film modified glassy carbon electrode

An electrochemical sensor, based on a graphene oxide (GO)-Nafion composite film modified glassy carbon electrode (GCE), was developed and used for detection of trace amounts of colchicine. Owing to the large surface area, good conductivity of GO and good affinity of Nafion, the sensor exhibited excellent electrocatalytic activity for the oxidation of colchicine, displaying a wide linear response from 5.0 × 10(-8) to 2.0 × 10(-5) mol L(-1) and a low detection limit of 1.5 × 10(-8) mol L(-1) in 0.1 mol L(-1) H(2)SO(4) solution. And this modified electrode exhibited a superior immunity from epinephrine, dopamine and ascorbic acid interference. The method was also applied successfully to detect colchicine in medicinal tablets.     

Sensitive detection of esculetin based on a CdSe nanoparticles-decorated poly(diallyldimethylammonium chloride)-functionalized graphene nanocomposite film

An electrochemical sensor based on a CdSe nanoparticles (NPs)-decorated poly(diallyldimethylammonium chloride) (PDDA)-functionalized graphene (CdSe-PDDA-G) nanocomposite was fabricated for the sensitive detection of esculetin. The nanocomposite was characterized by X-ray diffraction (XRD), ultraviolet/visible spectra (UV-vis) and transmission electron microscopy (TEM). Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were used to investigate the electrochemical behaviors of esculetin on the CdSe-PDDA-G composite film-modified glassy carbon electrode (GCE). The experimental results indicated that the incorporation of CdSe NPs with PDDA-G greatly enhanced the electrochemical response of esculetin. This electrochemical sensor displayed satisfactory analytical performance for esculetin detection over a range from 1.0 × 10(-8) to 5.0 × 10(-5) mol L(-1) with a detection limit of 4.0 × 10(-9) mol L(-1) (S/N = 3). Moreover, the sensor also exhibited good reproducibility and stability, and could be used for the detection of esculetin in real samples with satisfactory results.     

Thiocyanate ion selective electrode based on bis(N-3-methylphenyl salicylidenaminato)copper(Ⅱ) ionophore

In this work a PVC membrane electrode based on bis(N-3-methyl phenyl salicylidenaminato)copper(II)as ionophore was prepared.The electrode was tested by inorganic anions and showed good selectivity for thiocyanate ion.This sensor showed Nerstian behavior with a slope of a-59.3 mV per decade at 25℃.The proposed electrode exhibited a wide linear range from 1.0 × 10~(-6) mol/L to 1.0× 10~(-1) mol/L with a detection limit of 5.0×10~(-7) mol/L.The electrode response was independent of pH in the range of 4.0-10.0.The response time is about 9-21s,and the electrode can be used for over 60 days without considerable deterioration.The prepared sensor was applied as an indicator electrode in potentiometric titration of SCN with Ag~+ ion and to determine the thiocyanate in samples of urine and saliva.     

基于纳米MnO2-MWCNTs复合材料修饰的葡萄糖传感器

采用水热法制备了纳米MnO2,并用红外光谱,X射线衍射(XRD)和扫描电子显微镜(SEM)对其进行了表征。将碳纳米管和纳米MnO2分散在壳聚糖溶液中,用滴涂法固定到玻碳电极表面,制成修饰电极。利用计时电流法对该葡萄糖传感器的性能进行了研究,纳米MnO2-MWCNTs复合物对葡萄糖的氧化有明显的催化作用。在优化的条件下,葡萄糖在5.0×10-5～3.0×10-2mol/L浓度范围内,计时电流与浓度之间呈线性关系,检出限为1.5×10-5 mol/L(S/N=3)。对1.0×10-3 mol/L葡萄糖溶液平行测定8次的相对标准偏差(RSD)为2.1%。该传感器可成功用于葡萄糖注射液中葡萄糖的测定,回收率在96.4%～98.6%之间。