New soluble, thermally stable poly(amide-imide)s containing cardo anthraquinone unit

Preparation of new types of polyimides with high thermal stability and improved solubility was considered. In this way, two new amide diamines containing bulky pendant units were prepared in two steps: nucleophilic substitution reactions of 1- and 2-aminoanthraquinone with 3,5-dinitrobenzoyl chloride to form amide containing dinitro compounds, and then reduction of resulted dinitro compounds with hydrazine monohydrate in the presence of palladium/activated carbon. Two series of new poly(amide-imide)s were prepared from the reactions of these two diamines with various dianhydrides by one step polyimidation process. All poly(amide-imide)s were characterized by FTIR and ¹H-NMR spectroscopies and elemental analysis. The polymers were obtained in high yields with inherent viscosities of 0.54-0.69 dl g⁻¹. X-ray diffraction patterns (XRD) showed that all the polymers were amorphous and therefore this factor in addition to the introduction of bulky anthraquinone group led to good solubility of the polymers in most common organic solvents especially in N-methyl-2-pyrrolidone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), and dimethylsulfoxide (DMSO). Thermal analysis showed glass transition temperature between 204 and 226 °C. Decomposition temperatures were more than 293 °C, also 10% weight loss were in the range of 387-419 °C in air.     

Synthesis and characterization of norbornane-containing cardo polyamides

A new diamine, 2,2-bis[4-(4-aminophenoxy)phenyl]norbornane (BAPN), containing both ether and norbornane cardo groups, was synthesized in three steps started from norcamphor. A series of cardo polyamides were obtained by the direct polycondensation of BAPN and various aromatic dicarboxylic acids in N-methyl-2-pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. Polyamides had inherent viscosities in the range of 0.82–1.58 dL g⁻¹, and were readily soluble in polar aprotic solvents such as NMP, N,N-dimethylacetamide (DMAc) and N,N-dimethylformamide and dimethyl sulfoxide. These polymers were cast in DMAc solution into transparent, flexible, and tough films that were further characterized by X-ray and mechanical analysis. All the polymers were amorphous, and the polyamide films had a tensile strength range of 71–89 MPa, an elongation at break range of 5–9%, and a tensile modulus range of 2.0–2.3 GPa. Polyamides showed glass transition temperatures in the range of 256–296°C as measured by DSC and thermogravimetric analysis indicated no weight loss below 450°C in nitrogen and air atmosphere. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2791–2794, 1999     

Synthesis,characterization and properties of novel polyamides containing ferrocene unit and flexible spacers

Synthesis and characterization of ferrocene‐containing main‐chain polyamides are reported in this article. A new, interesting type of organometallic monomer (FDADO) based on ferrocene was prepared by interfacial condensation of 1,1′‐dichlorocarbonyl ferrocene with 2 mol 1,8‐diamino‐3,6‐dioxaoctane (DADO). A series of ferrocene‐based polyamides was prepared via polycondensation of the ferrocenyl diamine (FDADO) with different diacid chlorides using two different methods. The monomer and polymers were characterized by elemental analysis, infrared and NMR spectroscopy. The thermal stability and behavior of the synthesized polymers were evaluated by thermal gravimetric analysis (TGA), dynamic mechanical thermal analysis (DMTA), and differential scanning calorimetry (DSC). The crystallinity of polymers was examined by X‐ray diffraction analysis. Inherent viscosity, solubility and flame‐retardancy of the polymers were also studied. The obtained polymers showed good heat‐resistance and flame‐retardancy, and improved solubility vs generally reported polyamides in some common organic solvents. Copyright © 2007 John Wiley & Sons, Ltd.     

Effects of carbon nanotubes on the thermal stability and flame retardancy of intumescent flame-retarded polypropylene

Flame retardant mixtures of carbon nanotubes (CNTs) and intumescent flame retardant (IFR) were embedded in polypropylene (PP) to investigate what will happen if the additives exhibit two different flame retardation mechanisms. TEM tests showed that CNTs dispersed homogenously in PP matrix without any visible agglomeration. The effects of CNTs on thermal stability and flammability of PP were investigated by thermogravimetry (TG) and cone calorimetry tests, respectively. Results indicated that the introduction of CNTs only enhanced thermal stability of materials in a certain temperature range, but caused a severe deterioration of flame retardancy due to the interaction of the network structure and the intumescent carbonaceous char. Furthermore, conditions for an intumescent flame retardation system to behave with high efficiency were also discussed by a secondary combustion test.     

Enhancement of a hyperbranched charring and foaming agent on flame retardancy of polyamide 6

A hyperbranched polyamine was prepared using an A₂ + B₃ approach. It acted as a hyperbranched charring and foaming agent (HCFA) in combination with ammonium polyphosphate (APP) to form a new intumescent flame retardant (IFR) system for polyamide 6 (PA6). Effect of HCFA on flame retardant and thermal degradation properties of IFR‐PA6 was investigated by limiting oxygen index (LOI), UL‐94 vertical burning, cone calorimeter, and thermogravimetric analysis (TGA) tests. The IFR system presented the most effective flame retardancy in PA6 when the weight ratio of APP to HCFA was 2:1. The LOI value of IFR‐PA6 could reach 36.5 with V‐0 rating when the IFR loading was 30 wt%. Even if the loading decreased to 25 wt%, IFR‐PA6 could still maintain V‐0 rating with an LOI value of 31. TGA curves indicated that APP would interact with both PA6 and HCFA in PA6/APP/HCFA composite under heating. The interaction between APP and HCFA improved the char formation ability of IFR system and then much more char was formed for PA6/APP/HCFA composite than for PA6/APP. Therefore, better flame retardancy was achieved. Moreover, the structure and morphology of char residue were studied by Fourier transform infrared (FTIR), X‐ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). The results indicated that compact and foaming char layer containing P‐O‐C structure was formed for PA6/APP/HCFA system during combustion. Copyright © 2010 John Wiley & Sons, Ltd.     

The effect of hBN on the flame retardancy and thermal stability of P-N flame retardant PA6

A novel thermally conductive Polyamide 6 (PA6) with good fire resistance was prepared by introducing a phosphorous-nitrogen flame retardant (FR) and platelet-shaped hexagonal boron nitride (hBN) into the matrix. With high thermal conductivity and good flame retardancy, the material is suitable for applications in electronic and electrical devices. The limiting oxygen index (LOI) changes for various loadings content of FR. However this formulation still does not show an ideal fire resistance, due to the appearance of melt dripping behavior during the UL 94 test. With the extra introduction of 3 vol% and 5 vol% hBN, the melt dripping behavior during the burning process completely disappeared. The hBN also increased the thermal conductivity. Furthermore PA6 compounded with FR and hBN showed a better thermal stability than neat PA6. The morphology of the char residues was investigated by scanning electron microscopy (SEM). The flaky hBN acted as the framework in the char structure and the rigid hBN could effectively break the bubble-shaped char on the surface of the residues which resulted in the enhancement of the strength and compactness of the char.     

Flame retardancy of polyamide 66 nanocomposites with thermally stable organoclay

A thermally stable imidazolium organoclay was synthesized to improve the flame retardancy performance of polyamide 66 (PA 66). To enhance flame retardancy of the PA 66/organoclay nanocomposite, the thermally stable organoclay was coated with monomethylol melamine (MMM) before melt‐compounding with PA 66. Transmission electron microscopy and X‐ray diffraction results confirmed the partial exfoliation of the organoclay in the PA 66 matrix. The use of the thermally stable organoclay did not affect the thermal stability of PA 66. The cone calorimeter results showed that the PA 66/orgnaoclay nanocomposite exhibited a greatly reduced heat release rate and a longer ignition time. However, the PA 66/organoclay binary nanocomposite had no rating in the UL‐94 vertical burning test because it did not extinguish until the entire polymer component was burnt. The PA 66 nanocomposite with 15 wt% of MMM‐coated organoclay performed better in the ignition resistance test than the PA 66/organoclay nanocomposite containing 15 wt% of melamine. Copyright © 2011 John Wiley & Sons, Ltd.     

Modified montmorillonite combined with intumescent flame retardants on the flame retardancy and thermal stability properties of unsaturated polyester resins

Modified montmorillonite‐containing phytic acid (PA‐MMT) has been prepared by acid treatment and then introduced into unsaturated polyester resin (UPR) with an intumescent flame retardant (IFRs). The flame retardancy and thermal degradation of UPR/IFRs/PA‐MMT were evaluated by a limiting oxygen index (LOI) test, a vertical burning test (UL‐94), a thermogravimetric analysis (TGA), and a cone calorimeter test (CCT). Besides, the mechanical properties were studied by a universal testing machine. The LOI value of UPR/IFRs/PA‐MMT composites was increased to 29.2%. The CCT results indicated that the incorporation of PA‐MMT and IFRs significantly improved the combustion behavior of UPR. The results of the mechanical properties indicated that 1.5 wt% loading of PA‐MMT in UPR/IFRs showed the highest improvement in flexural strength and tensile strength. The flame‐retardant mechanism of PA‐MMT/IFRs was examined and discussed based on the results of combustion behavior and char analysis.     

Study on intumescent flame retarded polystyrene composites with improved flame retardancy

The flame retardancy and thermal stability of ammonium polyphosphate/tripentaerythritol (APP/TPE) intumescent flame retarded polystyrene composites (PS/IFR) combined with organically-modified layered inorganic materials (montmorillonite clay and zirconium phosphate), nanofiber (multiwall carbon nanotubs), nanoparticle (Fe₂O₃) and nickel catalyst were evaluated by cone calorimetry, microscale combustion calorimetry (MCC) and thermogravimetric analysis (TGA). Cone calorimetry revealed that a small substitution of IFR by most of these fillers (≤2%) imparted substantial improvement in flammability performance. The montmorillonite clay exhibited the highest efficiency in reducing the peak heat release rate of PS/IFR composite, while zirconium phosphate modified with C₂₁H₂₆NClO₃S exhibited a negative effect. The yield and thermal stability of the char obtained from TGA correlated well with the reduction in the peak heat release rate in the cone calorimeter. Since intumesence is a condensed-phase flame process, the MCC results showed features different from those obtained from the cone calorimeter.     

Thermal degradation and flame retardancy of epoxy resins containing intumescent flame retardant

Pentaerythritol diphosphonate melamine-urea-formaldehyde resin salt, a novel cheap macromolecular intumescent flame retardants (IFR), was synthesized, and its structure was a caged bicyclic macromolecule containing phosphorus characterized by IR. Epoxy resins (EP) were modified with IFR to get the flame retardant EP, whose flammability and burning behavior were characterized by UL 94 and limiting oxygen index (LOI). 25 mass% of IFR were doped into EP to get 27.2 of LOI and UL 94 V-0. The thermal properties of epoxy resins containing IFR were investigated with thermogravimetry (TG) and differential thermogravimetry (DTG). Activation energy for the decomposition of samples was obtained using Kissinger equation. The resultant data show that for EP containing IFR, compared with EP, IFR decreased mass loss, thermal stability and R _max, increased the char yield. The activation energy for the decomposition of EP is 230.4 kJ mol⁻¹ while it becomes 193.8 kJ mol⁻¹ for EP containing IFR, decreased by 36.6 kJ mol⁻¹, which shows that IFR can catalyze decomposition and carbonization of EP.     

Flame retardancy and thermal degradation of intumescent flame retardant polypropylene material

The flame retardancy and thermal degradation properties of polypropylene (PP) containing intumescent flame retardant additives, i.e. melamine pyrophosphate (MPyP) and charring‐foaming agent (CFA) were characterized by limiting oxygen index (LOI), UL 94, cone calorimeter, microscale combustion calorimetry, and thermogravimetric analysis (TGA). It has been found that the PP material containing only MPyP does not show good flame retardancy even at 30% additive level. Compared with the PP/MPyP binary system, the LOI values of the PP/MPyP/CFA ternary materials at the same additive loading are all increased, and UL 94 rating is raised to V‐0 from no rating (PP/MPyP). The cone calorimeter results show that the heat release rate and mass loss rate of some ternary materials decrease in comparison with the binary material. The microscale combustion calorimetry results indicate that the sample containing 22.5 wt% MPyP and 7.5 wt% CFA has the lowest heat release rate among all samples. The TGA results show that the thermal stability of the materials increases with the addition of MPyP, while decreases with the addition of CFA. Copyright © 2009 John Wiley & Sons, Ltd.     

含季戊四醇磷酸酯阻燃剂的合成与表征

采用1-氧代-4-羟甲基-2,6,7-三氧杂-1-磷杂双环[2.2.2]辛烷(PEPA)、三氯氧磷、双酚A和双酚S为反应物,合成了两个新型添加型阻燃剂:双酚A双[二(1-氧代-1-磷杂-2,6,7-三氧杂双环辛烷-4-亚甲基)]磷酸酯(BAPP)和双酚S双[二(1-氧代-1-磷杂-2,6,7-三氧杂双环辛烷-4-亚甲基)]磷酸酯(BSPP),通过元素分析、FT-IR和1H NMR等表征了标题化合物的结构,结果表明,所合成的标题化合物的结构与预期一致。热失重分析结果证明,BAPP和BSPP质量损失5%(wt)时的温度分别为343.6℃和352.3℃,600℃残余量分别达46.6%和55.5%,具有较高的热稳定性和结炭性能。阻燃性能实验证明,E-51环氧树脂中分别添加质量分数为18.2%(wt)的BAPP和BSPP时,极限氧指数分别为32.2%和31.8%,均能达到UL 94 V-0级。     

Flame retardancy and thermal degradation of intumescent flame retardant polypropylene with MP/TPMP

The performances of the novel intumescent flame retardant (IFR) polypropylene (PP) composites containing melamine phosphate (MP) and tris(1‐oxo‐2,6,7‐trioxa‐1‐phosphabicyclo[2,2,2]methylene‐4)phosphate (TPMP) were investigated. The flame retardancy of IFR‐PP system was characterized by limiting oxygen index (LOI) and UL 94 and cone calorimeter. The morphology of the char obtained after cone calorimeter testing was studied by scanning electron microscopy (SEM). The thermal oxidative degradation (TOD) of the composites was investigated by using thermogravimetric analysis (TGA) and real‐time Fourier transform infrared spectroscopy (RT‐FTIR). Compared with the PP/ TPMP or PP/ MP binary composite, at the same addition level, the LOI values of the PP/MP/TPMP ternary composites increase and reach V‐0 at the suitable MP/TPMP ratio. The results of TGA and RT‐FTIR showed the existence of the interaction between IFR and PP. Copyright © 2008 John Wiley & Sons, Ltd.     

二季戊四醇磷酸酯三聚氰胺盐的合成及阻燃性能测试

以磷酸、季戊四醇、三聚氰胺为原料,通过酸醇直接酯化和烘焙中和两步反应合成膨胀型阻燃剂二季戊四醇磷酸酯三聚氰胺盐,并对烘焙中和反应条件及其在聚乙烯中的阻燃性能进行了研究.确定最佳合成条件:n (二季戊四醇磷酸酯):n (三聚氰胺)=1:1;反应温度130-140℃;反应时间3-4h.将此阻燃剂添加到聚乙烯中,样品重量35...     

Thermal degradation and flame retardancy of fumaric acid in thermoplastic polyurethane elastomer

In this paper, fumaric acid (FA) which was a new type of environmental and low‐cost flame retardant was applied for thermoplastic polyurethane elastomer (TPU). The flame‐retardant properties of TPU were tested using limiting oxygen index, cone calorimeter test, smoke density test, and thermogravimetric/Fourier transform infrared spectroscopy. It has been proved that FA could improve the difficulty of the ignition of the sample; the limiting oxygen index value of the sample (FA‐4) increased by 29.7% when 2.0 wt% FA was added to TPU. The cone calorimeter test showed that FA can greatly reduce heat release and smoke production during the combustion process of TPU composites. For example, compared with the pure TPU, the peak heat release rate and total smoke release of the sample (FA‐4) with 2.0 wt% FA were decreased by 50.8% and 51.5% respectively. The results of smoke density test showed that the luminous flux of the samples contained 0.5 wt% FA was increased by 79.2% compared with the pure TPU. The TG results revealed that the sample of FA‐4 had higher char residue content compared with the sample of TPU. The results of thermogravimetric/Fourier transform infrared spectroscopy proved that FA could decrease the initial decomposition temperature for TPU composites and increase the release of CO₂ and H₂O. All results of test illustrated that FA had good flame‐retardant effect on TPU.     

Polyurethane-zinc borate composites with high oxidative stability and flame retardancy

Novel polyurethane zinc borate composites were prepared with the main aim to increase the flame retardancy of the polyurethane. It was discovered that the zinc borate had very significant effects on the oxidative stability of the neat polymer which was first observed by oxygen induction time tests and supported with actual weathering chamber tests. The oxidative stability of zinc borate-filled polyurethane was compared with the polyurethane stabilized with a commercial light stabilizer, Tinuvin B75 from Ciba SC. The performance of zinc borate-filled polyurethane was much better, as shown by oxygen induction time and weathering chamber tests. Additionally the flame retardancy was measured and significant flame retardancy was achieved. Mechanical tests, thermogravimetric analysis and scanning electron microscope studies were performed to characterize the products.     

Simultaneously improving the flame retardancy and mechanical properties for polyamide 6/aluminum diethylphosphinate composites by incorporating of 1,3,5‐triglycidyl isocyanurate

The effect of 1,3,5‐triglycidyl isocyanurate (TGIC) as a synergistic agent on the fire retardancy, thermal, and mechanical properties for polyamide 6/aluminium diethylphosphinate (PA6/AlPi) composites were investigated in detail by limiting oxygen index; vertical burning (UL‐94); cone calorimeter; thermal gravimetric analysis; rheological measurements; and the tests of tensile, flexural, and Izod impact strength. The morphologies and chemical compositions of the char residue were investigated by scanning electron microscopy, X‐ray photoelectron spectroscopy, and Fourier transform infrared spectra. The results demonstrated that AlPi and TGIC exerted an evident synergistic effect for flame retardant PA6 matrix, and the PA6/AlPi/TGIC composites with the thickness of 1.6 mm successfully passed UL‐94 V‐0 rating with the limiting oxygen index value of 30.8% when the total loading amount of AlPi/TGIC with the mass fraction of 97:3 was 11 wt%. However, the samples failed to pass the UL‐94 vertical burning tests when AlPi alone is used to flame retardant PA6 matrix with the same loading amount. The thermal gravimetric analysis data revealed that the introduction of TGIC promoted the char residue formation at high temperature. The rheological measurement demonstrated that the incorporation of TGIC improved the storage modulus, loss modulus, and complex viscosity of PA6/AlPi/TGIC composites comparing with that of neat PA6 and PA6/AlPi composites due to the coupling reaction between TGIC and the terminal groups of PA6 matrix. The morphological structures of char residues demonstrated that TGIC benefited to the formation of more homogenous and integrated char layer with no defects and holes on the surface comparing with that of PA6/AlPi composites during combustion. The higher melt viscosity of composites and the integrated and sealed char layer effectively inhibited the volatilization of flammable gas into the combustion zone and then led to the reduction of the heat release. The results of mechanical properties revealed that the incorporation of TGIC enhanced the mechanical properties for PA6/AlPi/TGIC composites comparing with that of PA6/AlPi composites with the same loading amount of flame retardant caused by the chain extension effect of TGIC. As a result, the flame retardancy and mechanical properties of PA6/AlPi composites simultaneously enhanced due to the introduction of TGIC.     

Modified cyanate ester resins with lower dielectric loss,improved thermal stability,and flame retardancy

Novel modified cyanate ester (CE) resins with decreased dielectric loss, improved thermal stability, and flame retardancy were developed by copolymerizing CE with hyperbranched phenyl polysiloxane (HBPPSi). HBPPSi was synthesized through the hydrolysis of phenyltrimethoxysilane, and its structure was characterized by ¹H‐NMR, ²⁹Si‐NMR, and Fourier transform infrared spectra. The effect of the incorporation of HBPPSi into CE resin on the curing behavior, chemical structure of cured networks, and typical performance of HBPPSi/CE resins were systemically evaluated. It is found that the incorporation of HBPPSi into CE network obviously not only catalyzes the curing of CE, but also changes the chemical structure of resultant networks, and thus results in significantly decreased dielectric loss, improved thermal stability, and flame retardancy as well as water absorption resistance. For example, in the case of the modified CE resin with 10 wt% HBPPSi, its limited oxygen index is about 36.0, about 1.3 times of that of neat CE resin, its char yield at 800°C increases from 31.6 to 35.4 wt%; in addition, its dielectric loss is only about 61% of that of neat CE resin at 1 kHz. All these changes of properties are discussed from the view of the structure–property relationship. The significantly improved integrated properties of CE resin provide a great potential to be used as structural and functional materials for many cutting‐edges fields. Copyright © 2011 John Wiley & Sons, Ltd.     

A vanillin-derived flame retardant based on 2-aminopyrimidine for enhanced flame retardancy and mechanical properties of epoxy resin

In order to give epoxy resin good flame retardance, a novel bio-based flame retardant based on 2-aminopyrimidine (referred to as VAD) was synthesized from renewable vanillin as one of the starting materials. Its structure was confirmed by NMR and mass spectra. The epoxy resins containing VAD were prepared by utilizing 4,4-diaminodiphenylmethane (DDM) as a co-curing agent, and their flame-retardant, mechanical and thermal properties and corresponding mechanisms were studied. VAD accelerated the cross-linking reaction of DDM and E51 (diglycidyl ether of bisphenol A). 12.5 wt% VAD made the epoxy resin achieve UL-94 V-0 rating and its limited oxygen index (LOI) value increase from 22.4% to 32.3%. The cone calorimetric testing results revealed the decline in the values of total heat release (THR) and peak of heat release rate (pk-HRR) and the obvious enhancement of residue yield. A certain amount of VAD enhanced the flame inhibition, charring and barrier effects, resulting in good flame retardance of the epoxy resin. Furthermore, the tensile strength, flexural strength and flexural modulus of the epoxy resin with 12.5 wt% loading of VAD were 6.5%, 14.9%, 15.2% higher than those of EP, indicating the strengthening effect of VAD. This work guarantees VAD to be a promising flame retardant for enhancing the fire retardancy of epoxy resin without compromising its mechanical properties.     

Poly(vinyl alcohol)/melamine phosphate composites prepared through thermal processing: thermal stability and flame retardancy

Poly(vinyl alcohol)/melamine phosphate composites (PVA/MP) as a novel halogen‐free, flame‐retardant foam matrix were prepared through thermal processing, and then their thermal stability and flame retardancy were investigated by thermo‐gravimetric analysis, micro‐scale combustion calorimeter, cone calorimeter, vertical burning test, and limiting oxygen index (LOI) test. It was found that the thermal stability and combustion properties of the PVA/MP composites could be influenced by the addition of MP. Compared with the control PVA sample (B‐PVA), in the PVA/MP (75/25) composites, the temperature at 5% mass loss (T_5%) decreased about 10°C, the residual chars at 600°C increased by nearly 27%, the temperature at the maximum peak heat release rate (T_P) shifted from 292°C to 452°C, and the total heat released and the heat release capacity (HRC) decreased by 28% and 14%, respectively. Moreover, the PVA/MP composites could reach LOI value up to 35% and UL94 classification V‐0, showing good flame retardancy. At the same time, both Fourier transform infrared and X‐ray photoelectron spectroscopy spectra of the residual chars from the PVA/MP composites demonstrated that the catalytic effect of MP on the dehydration and decarboxylation reactions of PVA, and the chemical reactivity of MP during the chars‐forming reactions could be used to account for the changed thermal stability and flame retardancy of the PVA/MP composites. Copyright © 2012 John Wiley & Sons, Ltd.