Optimization of a novel headspace–solid‐phase microextraction–gas chromatographic method by means of a Doehlert uniform shell design for the analysis of trace level ethylene oxide residuals in sterilized medical devices

Medical devices sterilized by ethylene oxide (EtO) retain trace quantities of EtO residuals, which may irritate patients' tissue. Reliably quantifying trace level EtO residuals in small medical devices requires an extremely sensitive analytical method. In this research, a Doehlert uniform shell design was utilized in obtaining a response surface to optimize a novel headspace–solid‐phase microextraction–gas chromatographic (HS‐SPME‐GC) method developed for analyzing trace levels of EtO residuals in sterilized medical devices, by evaluating sterilized, polymer‐coated, drug‐eluting cardiovascular stents. The effects of four independent experimental variables (HS‐SPME desorption time, extraction temperature, GC inlet temperature and extraction time) on GC peak area response of EtO were investigated simultaneously and the most influential experimental variables determined were extraction temperature and GC inlet temperature, with the fitted model showing no evidence of lack‐of‐fit. The optimized HS‐SPME‐GC method demonstrated overall good linearity/linear range, accuracy, repeatability, reproducibility, absolute recovery and high sensitivity. This novel method was successfully applied to analysis of trace levels of EtO residuals in sterilized/aerated cardiovascular stents of various lengths and internal diameter, where, upon heating, trace EtO residuals fully volatilized into HS for extraction, thereby nullifying matrix effects. As an alternative, this novel HS‐SPME‐GC method can offer higher sensitivity compared with conventional headspace analyzer‐based sampling. Copyright © 2009 John Wiley & Sons, Ltd.     

A head-space gas-chromatographic method for the determination of traces of ethylene oxide in sterilized medical devices

A head-space gas-liquid chromatography (HS-GLC) method for the determination of traces of ethylene oxide (EtO) in sterilized medical devices was developed. The method allows the determination of the amount of EtO by putting the samples directly into N,N-dimethylacetamide (DMA) and testing by means of HS-GLC. The procedure described is simple, sensitive, reproducible, and linear. The detection limit is 0.1 μg EtO/ml DMA, corresponding to 2 μg EtO/g sterilized material.     

Impurity analysis of 1,4-dioxane in nonionic surfactants and cosmetics using headspace solid-phase microextraction coupled with gas chromatography and gas chromatography-mass spectrometry

1,4-Dioxane impurity in nonionic surfactants and cosmetics were analyzed using solid-phase microextraction (SPME) coupled with gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS). Experimental results show that there is no significant difference using SPME-GC and SPME-GC-MS for analysis of 1,4-dioxane in three types of nonionic surfactants at the 95% confidence level. The relative standard deviation (R.S.D.) values of each analytical method were smaller than 3%. The amount of 1,4-dioxane was found to vary from 11.6 +/- 0.3 ppm to 73.5 +/- 0.5 ppm in 30% of nonionic surfactants from manufacturers in Taiwan. These methods were linear over the studied range of 3-150 ppm with correlation coefficients higher than 0.995. The recoveries of 1,4-dioxane for these nonionic surfactants following SPME were all higher than 96 +/- 1% (n = 3). The detection limits of 1,4-dioxane for these nonionic surfactants following SPME were from 0.06 ppm to 0.51 ppm. The experimentally determined level of 1,4-dioxane in cosmetics from manufacturers in Taiwan varied from 4.2 +/- 0.1 ppm to 41.1 +/- 0.6 ppm in 22% of daily used cosmetics following SPME coupled with GC and GC-MS. Conventional solvent extraction takes around 1 h for extraction and reconcentration but SPME takes only around 10 min. SPME provides better analyses of 1,4-dioxane in nonionic surfactants and cosmetics than conventional solvent extraction and head space pretreatments in term of simplicity, speed, precision, detection limit, and solvent consumption.     

Physically incorporated extraction phase of solid-phase microextraction by sol-gel technology

A sol-gel method for the preparation of solid-phase microextraction (SPME) fiber was described and evaluated. The extraction phase of poly(dimethysiloxane) (PDMS) containing 3% vinyl group was physically incorporated into the sol-gel network without chemical bonding. The extraction phase itself is then partly crosslinked at 320 degrees C, forming an independent polymer network and can withstand desorption temperature of 290 degrees C. The headspace extraction of BTX by the fiber SPME was evaluated and the detection limit of o-xylene was down to 0.26 ng/l. Extraction and determination of organophosphorus pesticides (OPPs) in water, orange juice and red wine by the SPME-GC thermionic specified detector (TSD) was validated. Limits of detection of the method for OPPs were below 10 ng/l except methidathion. Relative standard deviations (RSDs) were in the range of 1-20% for pesticides being tested.     

Recent developments in solid-phase microextraction

The main objective of this review is to describe the recent developments in solid-phase microextraction technology in food, environmental and bioanalytical chemistry applications. We briefly introduce the historical perspective on the very early work associated with the development of theoretical principles of SPME, but particular emphasis is placed on the more recent developments in the area of automation, high-throughput analysis, SPME method optimization approaches and construction of new SPME devices and their applications. The area of SPME automation for both GC and LC applications is particularly addressed in this review, as the most recent developments in this field have allowed the use of this technology for high-throughput applications. The development of new autosamplers with SPME compatibility and new-generation metal fibre assemblies has enhanced sample throughput for SPME-GC applications, the latter being attributed to the possibility of using the same fibre for several hundred extraction/injection cycles. For LC applications, high-throughput analysis (>1,000 samples per day) can be achieved for the first time with a multi-SPME autosampler which uses multi-well plate technology and allows SPME sample preparation of up to 96 samples in parallel. The development and evolution of new SPME devices such as needle trap, thin-film microextraction and cold-fibre headspace SPME have offered significant improvements in performance characteristics compared with the conventional fibre-SPME arrangement. Figure Photo of a high-throughput multi-fibre SPME PAS autosampler     

Solid-phase microextraction coupled with liquid chromatography for determination of beta-carotene in food

beta-Carotene in vegetables and nutritional products is analyzed using solid-phase microextraction (SPME) coupled with liquid chromatography (LC) to improve the speed of analysis and to reduce the consumption of organic solvents. The relative standard deviations (RSDs) of this analytical method for beta-carotene determinations in vegetables and nutritional products are approximately 10% and 5%, respectively. The amount of beta-carotene was found to vary from 0.35 +/- 0.05 ppm to 76.5 +/- 6.9 ppm for several vegetables in Taiwan. This method was linear over the range of 0.4-40 ppm with correlation coefficients higher than 0.997. The experimentally determined level of beta-carotene in nutritional products varied from 3.8 +/- 0.2 ppm to 24.6 +/- 1.1 ppm following SPME-LC. The recoveries of beta-carotene for these measurements following SPME were all higher than 97% +/- 2% (n = 3). The detection limits of beta-carotene for this method were from 0.027 to 0.054 ppm. Conventional solvent extractions take approximately 4-6 h for extraction and reconcentration but SPME takes approximately 1 h. From several tens to hundreds of milliliters, organic solvents can be saved using SPME. SPME provides better analyses on beta-carotene than conventional solvent extraction for nutritional products in terms of speed, precision, simplicity, and solvent consumption.     

Gas chromatographic–mass spectrometric methodology using solid-phase microextraction for the multiresidue determination of pesticides in surface waters

Solid-phase microextraction (SPME) coupled with gas chromatography–mass spectrometry (GC–MS) and selected ion monitoring (SIM) was used for the analytical determination of priority pesticide residues. Fibers coated with a 65-µm film thickness of polydimethylsiloxane divinylbenzene (PDMS-DVB) were used to extract 31 pesticides of different chemical groups. The quality parameters of the method demonstrated a good precision with detection limits of 1–56?ng/L. Linearity was controlled in the range of 0.1–50?µg/L. The proposed method was applied for the trace-level determination of the target pesticides in surface water samples including three rivers and one lake at the Epirus region (north-west Greece) for a period of one year. The results demonstrate the suitability of the SPME–GC–MS approach for the analysis of multi-residue pesticides in environmental water samples.     

High-performance polyethylene glycol-coated solid-phase microextraction fibers using sol-gel technology

The sol-gel method is applied for the preparation of solid-phase microextraction (SPME) fibers. An electron microscopy experiment suggested a porous structure for Superox-4 (polyethylene glycol, PEG) coating. SPME-GC analyses provided evidence that the sol-gel fibers have some advantages, such as high velocities of mass transfer, efficient extraction rates. high thermal stability, long life span, and spacious range of application for both polar and non-polar analytes. Efficient SPME-GC analyses of benzene-toluene-ethylbenzene-xylenes, phenols, phthalic diesters, naphthalene congeners and pesticides were achieved using sol-gel-coated PEG fibers.     

Detection of total microcystin in fish tissues based on lemieux oxidation and recovery of 2-methyl-3-methoxy-4-phenylbutanoic acid (MMPB) by solid-phase microextraction gas chromatography-mass spectrometry (SPME-GC/MS)

Microcystins (MCs) are widespread cyanobacterial toxins in freshwater systems, and have been linked to both acute and chronic health effects. A growing number of studies suggest that MC can bioaccumulate in food webs. Although, several methods (i.e. ELISA, LC-MS) have been developed for analysis of MC in water, extraction (for subsequent analysis) of the toxin from biological matrices (i.e. animal tissues) is impeded owing to covalent binding of toxins and active sites of their cellular targets, i.e. protein phosphatases. As an alternative approach, chromatographic methods for analysis of a unique marker, 2-methyl-3-methoxy-4-phenylbutanoic acid (MMPB), the product of the Lemieux oxidation of MCs, have been previously developed, and shown to measure total (bound and unbound) MC. Application, however, has been limited by poor recovery of the analyte. An improved recovery method is proposed – specifically the use of solid-phase microextraction (SPME). The MMPB analogue, 4-phenylbutanoic acid (4PB), and oxidized MC, were used to develop methods, and we specifically investigated several SPME fibres, and post-oxidation steps. Specifically, a method employing post-oxidation methyl esterification, followed by headspace SPME recovery of MMPB, was developed, and subsequently applied to analysis of environmental samples (i.e. fish tissues) previously shown to contain MCs. The method shows high linearity for both water and tissues spiked with MC, and an improved limit of quantitation of approximately 140?ng?g^?1. Evaluation of field samples by SPME-GC/MS detected considerably higher levels of MC, than detected by conventional methods (i.e. ELISA), and it is proposed that this technique reveals MC (particularly in the bound form) that is not detected by these methods. These results indicate that the developed method provides improved detection capability for MC in biological matrices, and will enhance our ability to understand bioaccumulation in freshwater food webs, as well as monitor exposure.     

Solid-phase microextraction coupled with gas chromatography and gas chromatography—Mass spectrometry for public health pesticides analysis

Summary Public health pesticides in two-component mixed solutions were analyzed using solid-phase microextraction (SPME) coupled with gas chromatography (GC) and gas chromatography—mass spectrometry (GC-MS). The two-component mixed solutions used were allethrin mixed with cyfluthrin, cypermethrin mixed with tetramethrin, and transfluthrin mixed with cyfluthrin. Quantitative SPME-GC and SPME-GC-MS analyses using calibration and standard addition methods were evaluated. Using SPME pretreatment saved several tens to hundreds of mL of organic solvent. Quantitative analyses of the SPME-GC and SPME-GC-MS using the calibration and standard addition methods showed promise for simple, fast, and solventless public health pesticide analysis.     

Determination of lasalocid sodium in animal feeds and premixes by reversed-phase liquid chromatography: collaborative study

A liquid chromatographic (LC) method for the analysis of lasalocid sodium in premixes, complete animal feeds, and trace-level feeds was collaboratively studied. The method employs a 0.5% HCI acidified methanol extraction followed by 20 min sonication in a water bath heated to 40 degrees C. Samples are then shaken on a mechanical shaker for 1 h and stored overnight, followed by an additional 10 min shaking the following morning. Sample extracts are diluted if necessary with extractant, filtered, and injected onto an LC system. Determination of all lasalocid homologs is by reversed-phase LC with fluorescence detection at 314 nm excitation and 418 nm emission. Eight samples of drug premixes, medicated feeds, and mineral supplements, along with 2 samples for trace-level analysis were sent to 20 collaborators in the United States, Canada, and The Netherlands. Study data were returned by 17 laboratories. Two additional supplemental trace-level samples and a blank feed were provided to 15 of the collaborating laboratories, and test data were received from all 15 participants. For the drug premixes, medicated feeds, and mineral supplements, RSDr values (within-laboratory repeatability) ranged from 1.2 to 19.9%, RSDR values (among-laboratory reproducibility) ranged from 3.4 to 32.3%, and HorRat values ranged from 0.35 to 3.73. For the trace-level samples, only lasalocid A, the predominant homolog comprising > 90% of the sum of all homolog peak area, was quantified. All laboratories correctly identified the analyte. Although some instrument response was reported by a number of laboratories for the blank feed, all but one laboratory's results were well below the 1 mg/kg limit of quantification. RSDr values for the initial 2 trace-level samples were excessive, ranging from 51.6 to 64.4%. RSDR values ranged from 51.6 to 75.7%, and HorRat values ranged from 3.6 to 4.0. Data for the initial trace-level samples indicated that the test samples were improperly prepared to ensure homogeneity, and a new set of supplemental samples was provided to collaborators, with significantly improved results. RSDr values for the 2 supplemental trace-level samples ranged from 1.6 to 2.5%, RSDR values ranged from 5.6 to 9.2%, and HorRat values ranged from 0.43 to 0.62.     

Electrolytically produced copper(I) chloride on the copper wire as an excellent sorbent for some amines

A new solid-phase microextraction (SPME) fiber has been developed and applied for the determination of some amines (n-pentylamine, tripropylamine, dibutylamine, diisobutylamine and tributylamine). In this study two copper wires were immersed in sodium chloride solution and electrolysis was performed at a constant potential. Anode was oxidized to copper(I) to produce copper(I) chloride as a sorbent for the studied amines on the copper wire. Several parameters affecting the fiber preparation and SPME procedure such as electrolysis time, selection of the SPME coating, extraction time and temperature were optimized. The copper(I) chloride fiber was the most appropriate one for the determination of amines by SPME-GC-FID. The optimized method was linear over the range studied (1-100 μg L⁻¹) and showed good precision, with R.S.D values less than 3% for all analytes. Fiber production was reproducible and R.S.D for fiber-to-fiber was less than 8%. The proposed SPME-GC method showed some advantages such as lower detection limits, a shorter analysis time and the avoidance of expensive commercial fibers.     

Cold fiber solid-phase microextraction device based on thermoelectric cooling of metal fiber

A new cold fiber solid-phase microextraction device was designed and constructed based on thermoelectric cooling. A three-stage thermoelectric cooler (TEC) was used for cooling a copper rod coated with a poly(dimethylsiloxane) (PDMS) hollow fiber, which served as the solid-phase microextraction (SPME) fiber. The copper rod was mounted on a commercial SPME plunger and exposed to the cold surface of the TEC, which was enclosed in a small aluminum box. A heat sink and a fan were used to dissipate the generated heat at the hot side of the TEC. By applying an appropriate dc voltage to the TEC, the upper part of the copper rod, which was in contact to the cold side of the TEC, was cooled and the hollow fiber reached a lower temperature through heat transfer. A thermocouple was embedded in the cold side of the TEC for indirect measurement of the fiber temperature. The device was applied in quantitative analysis of off-flavors in a rice sample. Hexanal, nonanal, and undecanal were chosen as three off-flavors in rice. They were identified according to their retention times and analyzed by GC-flame ionization detection instrument. Headspace extraction conditions (i.e., temperature and time) were optimized. Standard addition calibration graphs were obtained at the optimized conditions and the concentrations of the three analytes were calculated. The concentration of hexanal was also measured using a conventional solvent extraction method (697+/-143ng/g) which was comparable to that obtained from the cold fiber SPME method (644+/-8). Moreover, the cold fiber SPME resulted in better reproducibility and shorter analysis time. Cold fiber SPME with TEC device can also be used as a portable device for field sampling.     

Sol-Gel Method for the Preparation of Solid-Phase Microextraction Fibers

ABSTRACT

A novel sol-gel method is applied for the preparation of solid-phase microextraction (SPME) fibers. Scanning electron microscopy experiments suggested a porous structure for the poly(dimethylsiloxane) (PDMS) coating. SPME-GC analysis provided evidence that the sol-gel fibers have some advantages, such as high thermal stability, efficient extraction rates, high velocities of mass transfer, and spacious range of application.     

Determination of decoquinate in animal feeds by liquid chromatography: collaborative study

The performance characteristics of a liquid chromatographic (LC) method for the analysis of decoquinate (DEC) in supplements, premixes, and complete animal feeds at medicating and trace levels were collaboratively studied. DEC is extracted from ground feed samples with 1% calcium chloride-methanol solution using mechanical agitation for 90 min. After centrifugation for 5 min and dilution (if necessary), an aliquot of the extract is diluted with water. The diluted extracts are filtered and analyzed by reversed-phase LC with fluorescence detection. Suspect positive trace-level samples are confirmed by using an alternate excitation wavelength. Fourteen test samples of medicated feeds, supplement, and medicated premix, along with 8 test samples for trace-level analysis, were sent to 13 collaborators (one in Canada, 4 in Europe, and 8 in the United States). Test samples were analyzed as blind duplicates. Acceptable results were received from 12 laboratories for the medicated test samples and from 13 laboratories for the trace-level samples. Repeatability relative standard deviation estimates ranged from 1.3 to 5.6%. Reproducibility relative standard deviations estimates ranged from 2.8 to 6.1%, and HorRat values ranged from 0.22 to 0.74.     

Solid-phase microextraction/capillary gas chromatography for the profiling of confiscated ecstacy and amphetamine

Summary Impurity profiling of ecstacy and amphetamine seizures was accomplished by solid-phase microextraction (SPME) combined with capillary gas chromatography (GC). Samples were dissolved in 0.1 M aqueous acetate buffer (pH 5.0) as the only manual operation and subsequently subjected to SPME-GC. Ecstacy tablets were analyzed by head-space SPME to avoid contamination of SPME fibers with insoluble tablet components, while illicit amphetamine powders were exposed to immersed SPME. A SPME fiber of polydimethylsiloxane-divinylbenzene was found to provide excellent extraction of both polar and non-polar impurities. For both illicit ecstacy and amphetamine, complex impurity profiles were obtained by SPME providing a high information content. For ecstacy, profiles (relative peak areas) were repeatable within 2.2 to 12.6% RSD (n=6) while similar data on amphetamine varied between 2.0 and 10.9% RSD (n=6). No carry-over was observed although each fiber was used for 50 to 100 extractions.     

Investigation of volatile biomarkers in liver cancer blood using solid-phase microextraction and gas chromatography/mass spectrometry

Solid-phase microextraction (SPME) followed by gas chromatography/mass spectrometry (GC/MS) was used for the detection of liver cancer volatile biomarkers. Headspace SPME conditions (fiber coating, extraction temperature and extraction time) and desorption conditions were optimized and applied to the determination of volatiles in human blood. Between the liver cancer group (n = 19) and the normal group (n = 18), positive rates of 19 volatile compounds among the total of 47 detected were found to be different with statistical significance (p < 0.05, chi-squared test). We suggested hexanal, 1-octen-3-ol and octane, of the 19 compounds, as biomarkers of liver cancer with clinical diagnostic value. The sensitivity and specificity of 94.7% and 100% for hexanal, 84.2% and 100% for 1-octen-3-ol, and 89.5% and 100% for octane were obtained, respectively, after the cutoff values had been properly established. These results show that SPME-GC/MS is a simple, rapid and sensitive method for the investigation of volatile disease markers in human blood.     

Depletion solid-phase microextraction for the evaluation of fiber-sample partition coefficients of pesticides

A depletion solid-phase microextraction (SPME) method for the characterisation of SPME sorption for 13 pesticides selected as probe compounds is described. The sample is extracted and analysed multiple times by SPME-GC/MS. The observed depletion in peak areas is used for the calculation of extraction ratios that varied between 3 and 28% for a PDMS fiber with confidence intervals between 0.7 and 5.4%. Apparent fiber-sample partition coefficients can be calculated and extrapolated to equilibrium conditions if specific sorption kinetics are known. Under the chosen conditions, problems were encountered for more polar compounds (logK(ow)<3) due to inefficient extraction. The extracted amount was found to be the decisive parameter for depletion SPME and the extraction conditions therefore need to be adapted to the polarity of the analyte. The importance of the initial analyte concentration especially for mixed-mode fibers is demonstrated. Compared with conventional external calibration using liquid injection, depletion SPME eliminates uncertainties due to solvent effects during injection. Furthermore, it does neither require authentic reference compounds nor knowledge of the initial analyte concentration, and thus can even be used for unknowns.     

Determination of phthalates in water samples using polyaniline-based solid-phase microextraction coupled with gas chromatography

A simple solid-phase microextraction (SPME) device, coupled with gas chromatography-flame ionization detection (GC-FID), was developed to detect trace levels of phthalates in environmental water samples. Polyaniline (PANI) was chosen as the sorbent for the SPME device and was electrochemically deposited on a stainless steel wire to achieve high thermal and mechanical stability. The porous structure of the PANI film, characterized by scanning electron microscopy (SEM), suggested large extraction capability. Key parameters were optimized and five phthalates were selected to evaluate the SPME-GC procedures. The method was also applied to the analysis of lake and river water samples. Control experiments were carried out using commercial polyacrylate (PA) fiber. The new PANI-SPME-GC method offers high accuracy, precision and sensitivity and low detection limits. Thus, the method developed could be used as a new way to monitor the trace levels of phthalates in water medium. A possible extraction mechanism was investigated using electrochemical impedance spectroscopy (EIS).     

Comparison of comprehensive two-dimensional gas chromatography-time-of-flight mass spectrometry and gas chromatography-mass spectrometry for the qualitative characterisation of roasted barley by solid-phase microextraction

Volatile compounds of roasted barley used in the production of barley coffee, the most common coffee substitute, were analysed by using solid-phase microextraction (SPME) followed by GC-MS and comprehensive GC x GC-TOF-MS, respectively. The optimised SPME extraction conditions in terms of selection of the fibre coating, extraction time and extraction temperature allowed to obtain the highest GC response, thus enhancing the identification capabilities of the developed method. As for the SPME-GC x GC-TOF-MS analysis, 64 compounds with similarity, reverse and probability values above 800, 900 and 6000, respectively, were identified, by using a polar x apolar column set combination; in contrast, GC-MS was able to identify a lower number of compounds, i.e. 40 volatiles.