基准试剂纯度副基准装置通过审定

国防科工委化学计量一级站研制的基准试剂纯度副基准装置于1992年5月11日在济南通过了由国家技术监督局组织的考核审定。该装置通过对电阻、电动势、时间、质量等基本物理的测量来对基准试剂纯度进行定值,定值准     

用精密库仑滴定法测定重铬酸钾的纯度

一、前言用于容量分析的基准试剂,其纯度一般用化学分析法测定。化学分析法均需用另一种标准物质作基准,所以属于相对方法。1959年Taylor等人成功地建立了测定基准试剂纯度的精密库仑滴定法。此法依据法拉第定律,直接借助于质量、电压、电阻和时间等标准量来计算基准试剂纯度,因而是绝对法。     

基准试剂BaCl2纯度的测定

采用EDTA络合滴定法对BaCl2基准试剂的纯度进行测定.在滴定过程中加入EDTA-Mg,通过置换反应,以EDTA滴定Mg2 指示滴定终点,用ICP-MS法对该试剂中主要杂质如Fe、Eu、Yb、Lu等元素进行测定.EDTA络合滴定法结果与ICP-MS、GDMS杂质扣除法测定结果基本一致.该方法操作简单、快速,滴定时变色灵敏,测定结果精确度高.     

恒电流库仑法测定基准试剂三氧化二砷的含量

用恒电流库仑法测定基准试剂三氧化二砷的含量，以恒电流通过含有碘化钾，基准试剂三氧化二砷试样的弱碱性水溶液，利用工作电极铂阳极上电生滴定剂I2与亚砷酸盐定量反应，以死停终点法确定滴定终点，测量出电解电流和电解时间，根据法拉第电解定律并利用EXCEL计算出基准试剂三氧化二砷的含量。方法的回收率为100％。     

恒电流库仑分析法测定硫酸亚铁铵等基准试剂的纯度

在1．8mol／L硫酸介质中,以恒电流通过含有Mn^2＋的电解质溶液,使工作电极铂阳极上电生出Mn^3＋,Mn^3＋与溶液中待测基准试剂硫酸亚铁铵、草酸钠或草酸定量反应,以永停终点法确定库仑滴定终点,通过测量电解电流及电解时间,利用法拉弟电解定律计算基准试剂的纯度。该方法的相对误差为0．32％～0．36％,测量结果的相对标准偏差为0．045％-0．050％（n=11）。     

硫代硫酸钠标准溶液配制中标定基准物质的优化选择

对硫代硫酸钠标准溶液配制实验中不同基准物质的标定效果进行了对比研究,结合试剂用量、反应时间、显著性检验等分析说明不同基准物质所产生的结果:重铬酸钾、碘酸钾、溴酸钾均可实现对硫代硫酸钠溶液的标定。其中溴酸钾作为标定的基准物质时,试剂用量少,反应时间短,实验费用低且终点易于观察。双侧t检验符合统计学要求,更适用于硫代硫酸钠溶液标定,有望引入学生实验。     

测量不确定度及其在化学计量中的应用实例

介绍了测量不确定度的评定方法及其在基准试剂纯度、干涉滤光片波长标准物质、锌合金成分标准物质中的应用实例。     

甲苯纯度标准物质制备

研制了甲苯纯度标准物质。以市售甲苯高纯试剂为原料,对其结构及纯度进行验证,最终将其分装至1mL安瓿瓶。采用质量平衡法和定量核磁共振法两种不同原理方法对甲苯标准物质进行纯度定值。通过质量平衡法对特性量值进行均匀性检验、长期稳定性监测和模拟运输条件的短期稳定性监测,同时系统分析与评估了标准物质研制过程中定值、均匀性和稳定性引入的不确定度。结果表明,甲苯纯度标准物质的纯度值99.8%,扩展不确定度为0.2%(k=2),特性量值均匀性良好,12个月稳定性可靠。     

国军标恒电流库仑滴定装置检定规程正式颁布

为满足国防系统基准试剂定值装置计量检定的要求,由国防科工委化学计量一级站编制的国家军用标准恒电流库仑滴定装置检定规程已由国家军标委审批后正式颁布,其编号为GJB 2008—94,并将     

基于凝固点下降的高纯有机物纯度定值技术研究进展

介绍凝固点测量方法的研究进展。阐述了凝固点下降技术用于高纯有机物纯度定值的基本原理和适用条件,详细介绍了静力学方法和动力学方法这两种凝固点的测量方法,并介绍了两种方法在纯度定值方面的应用情况,且对两种方法的特点进行了对比,展望了凝固点下降纯度定值技术的发展趋势。     

Certified calibration solution reference material for the determination of perfluorooctane sulfonate from the National Metrology Institute of Japan (NMIJ)

A new calibration solution reference material for the determination of perfluorooctane sulfonate anion (PFOS) and its salts has been issued as a certified reference material (CRM) by the National Metrology Institute of Japan, National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). The purity amount-of-substance fraction of raw material potassium perfluorooctane sulfonate (K-PFOS) was evaluated based on the results obtained using the freezing point depression method, and the purity mass fraction of the raw material was calculated using the average molar mass of impurities, the molar mass of K-PFOS, and the purity amount-of-substance fraction. The certified concentration of this CRM was obtained by multiplying the dilution ratio of the raw material in a prepared solution (methanol) determined from the gravimetric blending method by the purity of the raw material. The preparation concentration of K-PFOS as a certified value of NMIJ CRM 4220-a was determined to be 9.93?mg?kg^?1. In addition, the standard uncertainty of the certified value was evaluated from the purity evaluation as well as from sample inhomogeneity, instability, and preparation variation obtained from LC/MS measurements of different gravimetrically prepared solutions of the NMIJ CRM. Consequently, the expanded uncertainty was estimated to be 0.15?mg?kg^?1 with a coverage factor k?=?2 corresponding to the half-width of estimated confidence interval of approximately 95%.     

Thermal standards from the laboratory of the government chemist

The Laboratory of the Government Chemist (LGC) is a focal point for the production, analysis and certification of reference materials. Within the field of thermal analysis the LGC is concerned with the development of purity standards and materials certified for enthalpy of fusion and melting point. For some time the LGC has been concerned with the significant differences in purity data which can be produced by the different manufactures' differential scanning calorimeters. This paper will highlight the initiatives the LGC is undertaking in overcoming this uncertainty in purity measurements through the use of certified thermal standards.     

河豚毒素标准样品的研制

采用质谱、核磁、红外及紫外对河豚毒素样品进行结构确证,采用柱后衍生高效液相荧光法对该纯度标准样品进行定值并进行了均匀性、稳定性检验。标准样品经国内6个具有分析资质的实验室进行协同定值,定值结果为99.45%,其扩展不确定度(95%置信区间)为0.51%。该标准样品达到国家标准样品的技术要求,可用于有关河豚毒素的方法校正和质量控制。     

Development of an obidoxime chloride reference material: a metrological approach to the determination of chromatographic purity

A metrological approach to determination of the chromatographic purity of obidoxime chloride and the corresponding obidoxime chloride reference material (RM) with a certified chromatographic purity value have been developed. This value was defined as the ratio of the sum of peak areas of obidoxime chloride isomers to the total peak area of detected substances including impurities (%) under specified HPLC–UV conditions. The RM homogeneity and stability were studied using HPLC with UV detection and evaluated as satisfactory. The certified value calculated from the results of an interlaboratory trial was equal to 99.9% with the expanded uncertainty of 0.6% at the level of confidence 0.95 and the coverage factor 2. The RM certified value, like other results of chromatographic purity determination traceable to the reference measurement procedure, is not traceable directly to the SI mole. However, the results are comparable in metrologically traceable environments, i.e. when relevant measuring laboratory instruments are calibrated with traceability chains to the corresponding SI units. Therefore, the RM can be used as a measurement standard (calibrator) for analytical instruments and as a control sample for quality control of HPLC obidoxime chloride assay results.     

低浓度氮中二氧化硫气体标准物质的制备

以二氧化硫纯度标准物质和高纯氮气为原料,采用与一级标准物质比较法制备了摩尔分数为10~100μmol/mol的氮中二氧化硫标准物质。用二氧化硫分析仪对配制的标准物质进行了机械混匀试验、压力均匀性和时间稳定性试验。结果表明,滚动30~80 min后该标准物质机械混匀良好;经F检验,在10~0.5 MPa范围内该标准物质量随压力变化无显著差异,具有较好的压力均匀性;在–20℃和40℃条件下保存7 d,其量值无显著变化,可满足运输环节量值稳定性要求;在常温下贮存11个月,量值无显著性变化,满足国家二级标准物质稳定性要求。采用与一级标准物质比较法定值,并对定值结果的不确定度进行了评定。研制的低浓度氮中二氧化硫气体标准物质的标准值分别为9.89,55.4,101.2μmol/mol(U_(rel)=2%,k=2),该标准物质满足国家二级标准物质的相关技术要求,可用于仪器校准、测量过程质量控制及分析方法的确认和评价。     

肌酐纯度标准物质的定值方法及其不确定度评定研究

通过定性及定量分析,研究了肌酐纯度标准物质的定值方法,并进行了定值分析的不确定度评定。首先使用三重四极杆质谱仪及核磁共振谱仪(氢谱)对肌酐样品进行定性分析,然后采用质量平衡法(包括液相色谱法、水分、灰分、挥发性物质和无机元素分析)与定量核磁共振法共同对肌酐纯度标准物质进行准确定值,最后对定值结果进行不确定度评定。肌酐的定值结果为99.7%,扩展不确定度为0.4%。该研究对于实际检测中肌酐的准确测定及临床上相关疾病的正确诊断治疗具有重要意义,且经过定值的肌酐纯品还可做定量核磁共振法的定量内标使用。定量分析后的肌酐经过均匀性检验和稳定性考察后可申报为国家标准物质。     

黄芩素纯度标准物质的定值及其不确定度评定

为了满足食品及医药等领域的检测需求,研制了黄芩素纯度标准物质。采用液相色谱–质谱法和红外光谱法对黄芩素纯度标准物质原料定性后,利用高效液相色谱法(HPLC)和定量核磁技术(Quantitative Nuclear Magnetic Resonance Spectroscopy,QNMR)对黄芩素的纯度进行了定值,并用HPLC法对黄芩素纯度标准物质进行了均匀性检验和稳定性考察。对定值结果的不确定度进行了评价,研制的黄芩素纯度标准物质的定值结果和扩展不确定度分别为98.8%,0.8%(k=2)。     

Are analytical standards and reagents really reliable?

Quality assurance is one of the major challenges in analytical chemistry, whatever the scope of application. The quality of analytical standards is very seldom questioned; however, sometimes odd results are obtained, and all the other potential sources of discrepancies are eliminated. So, we investigated the reliability of three analytical standards and reagents implemented for radiochemical and chemical characterizations of nuclear waste. In particular, this work examined the purity of a source of tritiated dodecane, the trueness of a certified concentration value and the purity for a diethylenetriaminepentaacetic acid (DTPA) reagent and the trueness of a certified concentration value for a multi-anion standard used in an interlaboratory comparison exercise. It was shown that the source of tritiated dodecane contains 60 % of tritiated impurities. The trueness of the DTPA concentration certified by the supplier was questioned due to the presence of impurities in the solution. It was proven that the long-term stability of the multi-anion standard was not guaranteed for nitrite. The results clearly demonstrated that, despite the certificates delivered by the suppliers, caution has to be taken toward the reliability of the analytical standards and reagents.     

加替沙星纯度标准物质研制

研制加替沙星纯度标准物质。采用质量平衡法和氢谱定量核磁法对加替沙星纯度标准物质候选物进行纯度定值,采用卡尔费休法和热重分析法准确测量了影响主成分纯度的水分含量,并考察了水分含量的稳定性。开展了加替沙星纯度定值、均匀性检验、稳定性考察以及不确定度评估。结果表明,加替沙星纯度标准物质的纯度值为93.1%,扩展不确定度为0.6%(k=2),水分含量为6.6%,特性量值均匀性良好,6个月稳定性可靠,被认定为国家二级标准物质,编号为GBW(E) 100476。研制的加替沙星纯度标准物质填补了国内空白,同时也为吸湿性较强的药物纯度标准物质研制过程中水分测定提供了参考与借鉴。     

Development of bovine serum albumin certified reference material

We present the development process for National Institute of Metrology (NIM) bovine serum albumin (BSA) certified reference material (CRM). Each CRM unit contains about 200 mg of purified BSA. The moisture, ignition residue, molecular weight, and high-performance liquid chromatography (HPLC) purity were analyzed and mass spectrometry based protein identification was carried out to ensure the material was BSA. Both amino acid based isotope dilution mass spectrometry (IDMS) and a purity deduction method were selected for value assignment. The certified value was the average of the IDMS and the purity deduction result. HPLC purity analysis was used to examine the homogeneity and stability of solid BSA CRM. Fifteen units were selected for between-bottle homogeneity examination and seven subsamples from the same bottle were selected for within-bottle homogeneity examination. Statistics showed the CRM passed both the between-bottle and the within-bottle homogeneity examination. The CRM stability under storage conditions (-20 °C) was tested for 18 months and no trend was observed. Uncertainties from the balance, amino acid purity, hydrolysis, method reproducibility, homogeneity, and stability were taken into account in uncertainty evaluation. The final certified value of NIM BSA CRM is (0.963±0.038) g/g.