A novel fluorescence sensor based on covalent immobilization of 3-amino-9-ethylcarbazole by using silver nanoparticles as bridges and carriers

A novel technique of covalent immobilization of indicator dyes in the preparation of fluorescence sensors is developed. Silver nanoparticles are used as bridges and carriers for anchoring indicator dyes. 3-amino-9-ethylcarbazole (AEC) was employed as an example of indicator dyes with terminal amino groups and covalently immobilized onto the outmost surface of a quartz glass slide. First, the glass slide was functionalized by (3-mercaptopropyl) trimethoxysilane (MPS) to form a thiol-terminated self-assembled monolayer, where silver nanoparticles were strongly bound to the surface through covalent bonding. Then, 16-mercaptohexadecanoic acid (MHDA) was self-assembled to bring carboxylic groups onto the surface of silver nanoparticles. A further activation by using 1-(3-dimethylaminopropyl)-3-ethylcarbodiimide hydrochloride (EDC) and N-hydroxysuccinimide (NHS) converted the carboxylic groups into succinimide esters. Finally, the active succinimide esters on the surface of silver nanoparticles were reacted with AEC. Thus, AEC was covalently bound to the glass slide and an AEC-immobilized sensor was obtained. The sensor exhibited very satisfactory reproducibility and reversibility, rapid response and no dye-leaching. Rutin can quench the fluorescence intensity of the sensor and be measured by using the sensor. The linear response of the sensor to rutin covers the range from 2.0 × 10⁻⁶ to 1.5 × 10⁻⁴ mol L⁻¹ with a detection limit of 8.0 × 10⁻⁷ mol L⁻¹. The proposed technique may be feasible to the covalent immobilization of other dyes with primary amino groups.     

Preparation and properties of polytetrafluoroethylene-modified polyacrylate via emulsion polymerization

One method of preparation of polytetrafluoroethylene(PFTE)-modified polyacrylate emulsion has been studied. Through pre-emulsion technology, PTFE powder could be dispersed by high speed shearing with high-speed dispersor. PFTE-modified polyacrylate has been prepared by in situ copolymerization of n-butyl acrylate, n-methyl methacrylate, n-styrene, and α-methacrylic acid in the presence of seed particles of dispersed PTFE by semi-starved addition method. The properties of the emulsion under various polymerization conditions were investigated. The morphology of the latex particles with about 180 nm were observed by scanning electron microscopy (SEM). It was shown that the particles with linear PTFE/core–polyacrylate/shell could eventually be dispersed homogeneously. TG showed that the heat-stability was improved obviously.     

A selective optical sensor for picric acid assay based on photopolymerization of 3-(N-methacryloyl) amino-9-ethylcarbazole

A novel optical sensor based on covalent immobilization for picric acid assay has been described. To improve the stability of the sensor, a terminal double bond was attached to the fluorescent compound, 3-amino-9-ethylcarbazole (AEC), via methacryloyl chloride. The resultant compound, 3-(N-methacryloyl) amino-9-ethylcarbazole (MAEC) was copolymerized with 2-hydroxypropyl methacrylate on surface-modified quartz glass plates by UV irradiation. The resulting optical sensor (optode membrane) was used to determine picric acid based on fluorescence quenching. It shows a linear response toward picric acid in the concentration range of 9.33 × 10⁻⁸ to 9.33 × 10⁻⁵ mol l⁻¹, with rapid response, high stability and good selectivity to picric acid.     

Preparation and application of functionalized nanoparticles of CdS as a fluorescence probe

CdS nanoparticles have been prepared and modified with mercaptoacetic acid. The functionalized nanoparticles are water-soluble and biocompatible. They could be used as a fluorescence probe in the determination of bovine serum albumin (BSA), which was proved to be a simple, rapid and specific method. In comparison with single organic fluorophores, these nanoparticle probes are brighter, more stable against photobleaching, and do not suffer from blinking. Under the optimum conditions, the response is linearly proportional to the concentration of BSA between 0.1 and 3.2 μg ml⁻¹, and the limit of detection is 0.08 μg ml⁻¹.     

基于DNA链置换反应的新型固定化酶反应器制备及应用

建立了一种新型的酶固定化方法,采用DNA链置换反应成功地在单链DNA标记的磁性纳米粒子上实现了酶的链置换无损更替。该技术可实现目标酶的再利用,节约了生产成本。制备的固定化胰蛋白酶微反应器具有较好的重复利用性和高酶切效率,重复使用10次后仍可保持原酶活性的86%;利用链置换反应制备的MNPs@DNATrypsin酶切马心肌红蛋白5 min后,即可获得95%±0%(n=3)的氨基酸序列覆盖率,远超过相同条件下自由酶酶切12 h的结果。实验表明,发展的固定化酶技术具有高磁响应性,便于从反应体系中回收固定化酶和重复使用,同时此技术可显著提高酶活性,因此可用于固定各种重要的酶,同时可将其广泛应用于各种酶促反应中。     

Label-free fluorescence turn-on detection of microRNA based on duplex-specific nuclease and a perylene probe

A novel fluorescence turn-on microRNA (miRNA) detection method based on duplex-specific nuclease (DSN) and a perylene probe is presented in this study. A positively charged perylene derivative (compound 1) was used as the fluorescent probe. Compound 1 exhibits strong monomer fluorescence in an aqueous buffer solution. It is well known that single-stranded DNA is a polyanion in nature. Thus, it can induce the aggregation of compound 1 through strong electrostatic, hydrophobic and π−π stacking interactions. As a result, the fluorescence of compound 1 was efficiently quenched. When the target miRNA was added, the formation of DNA-RNA hybridized duplex initiated the cleavage of the DNA strand by DSN cycle reaction, which resulted in disaggregation of compound 1. A fluorescence turn-on signal was detected, and a novel miRNA sensing method was therefore established. The presented method is label-free, simple, cost effective, sensitive and selective.     

A reversible chemosensor for nitrite based on the fluorescence quenching of a carbazole derivative

The carbazole derivative, with an amino group in 9-position (9-methylacryloylamino carbazole (MAC), has been utilized to prepare a fluorescent sensor and used for the determination of NO₂⁻ based on the reaction between nitrite (NO₂⁻) and excess I⁻ to form I₃⁻, which can quench the fluorescence of carbazole derivative. MAC, as a fluorescent carrier, has a terminal double bond and is covalently immobilized on a quartz glass plate surface by photo-polymerization to prevent the leakage of the dye. The sensor shows sufficient repeatability, selectivity, operational lifetime of 8 weeks, and a fast response of less then 30 s. NO₂⁻ can be determined in the range between 1.0×10⁻⁶ and 1.0×10⁻⁴ mol l⁻¹ with a detection limit of 8.0×10⁻⁷ mol l⁻¹ at pH of 2.0. The quenching mechanism is discussed. Most commonly coexisting ions do not interfer with the NO₂⁻ assay.     

Preparation of polymer particles having ethyleneurea groups at their surfaces by emulsifier-free seeded emulsion polymerization and wet adhesion of its emulsion film

Polymer emulsion having ethyleneurea groups at particle surfaces was produced by emulsifier-free seeded emulsion copolymerization of n-butyl methacrylate (BMA) and methacrylamide ethylethyleneurea (EU) with poly(BMA) seed particles utilizing the starved-fed monomer addition method. This emulsion film, prepared by casting the polymer emulsion on an alkyd resin plate, had a superior adhesion in water, as well as on stainless steel. Such superior wet adhesions seem to be based on a large amount of EU predominantly localized at the particle surfaces.Part CCXLIX of the series "Studies on suspension and emulsion"     

Preparation and application of functionalized nanoparticles of CdSe capped with 11-mercaptoundecanoic acid as a fluorescence probe

A new fluorescence probe, CdSe nanocrystal has been prepared and modified with 11-mercaptoundecanoic acid [HS-(CH₂)₁₀-COOH]. The functionalized nanoparticles were characterized using transmission electron microscopy (TEM), ultraviolet-visible (UV-vis) spectroscopy and photoluminescence (PL) spectroscopy. The results demonstrate that CdSe is dispersed homogeneously in aqueous solution and well protected from the environmental oxygen. They can be used as a new fluorescence probe for lysozyme, which was simple, rapid and specific. Under the optimum condition, the response is linearly proportional to the amount of lysozyme from 0.20 to 26.0 μg ml⁻¹, and the limit of detection is 0.115 μg ml⁻¹. The proposed method has been applied to the determination of lysozyme in egg white, with the recovery of 96-105%.     

Preparation of pH-sensitive polymer by thermal initiation polymerization and its application in fluorescence immunoassay

A fluorescence immunoassay for human IgG (Ag) was developed using a pH-sensitive polymer prepared by thermal initiation or redox initiation polymerization as a carrier. In the competitive immunoassay, appropriate quantity of Ag was immobilized on the polymer and the standard Ag (or sample) solution, and a constant amount of fluorescein isothiocyanate labeled goat anti-human IgG antibody (Ab-FITC) was added. Immobilized Ag and the standard (or sample) Ag competed for binding to the Ab-FITC in 37 °C in homogeneous format. After changing the pH to separate the polymer-immune complex precipitate, it was re-dissolved and determined by fluorescence method. The results showed that the immobilization efficiency, immunological reaction activities of immobilized Ag and phase transition pH range were improved as Ag was immobilized by thermal initiation instead of redox initiation polymerization. Under optimum conditions, the calibration graphs for the Ag in both methods, thermal initiation and redox initiation, were linear over the concentration range of 0.0-1000 ng mL⁻¹, with detection limits 8 (thermal initiation) and 12 ng mL⁻¹ (redox initiation), respectively. Moreover, some pH-sensitive polymer prepared only in organic solvent or under high temperature could also be used as an immunoreaction carrier by thermal initiation polymerization. Thermal initiation polymerization was a better immobilization mode.     

基于室温溶液悬浮法共价有机骨架的制备及其对茶叶中拟除虫菊酯固相微萃取的应用

拟除虫菊酯(PYs)类农药被广泛用于茶园病虫害的防治.随着国内外对进出口茶叶中农药残留限量的要求日益严格,我国迫切地需要开发能应用于检测茶叶中痕量PYs的方法.研究通过简单、温和的溶液悬浮法(SSA),在室温下制备了共价有机骨架(COF)材料TpBD,该材料具有优异的热/化学稳定性、较高的孔隙度和比表面积.通过简单物理...     

Preparation and characterization of poly(o-methoxyaniline)/Na-MMT clay nanocomposite via emulsion polymerization: Electrochemical studies of corrosion protection

A series of poly(o-methoxyaniline) (PMA)/Na⁺-montmorillonite (MMT) clay nanocomposite (Na⁺-PCN) materials have been successfully prepared by in situ emulsion polymerization in the presence of inorganic nanolayers of hydrophilic Na⁺-MMT clay with DBSA and APS as surfactant and initiator, respectively. The as-synthesized Na⁺-PCN materials were characterized by Fourier-transformation infrared (FTIR) spectroscopy, wide-angle powder X-ray diffraction (XRD) and transmission electron microscopy (TEM).Na⁺-PCN materials in the form of coatings with low loading of Na⁺-MMT clay (e.g., 5 wt.%, CLMA5) on cold rolled steel (CRS) were found much superior in corrosion protection over those of neat PMA based on a series of electrochemical measurements of corrosion potential, polarization resistance, corrosion current and impedance spectroscopy in 5 wt.% aqueous NaCl electrolyte. The molecular weight of PMA extracted from Na⁺-PCN materials and net PMA were determined by gel permeation chromatography (GPC) with NMP as eluant. Effects of material composition on the optical properties, electrical conductivity, thermal stability and surface morphology of neat PMA and/or a series of Na⁺-PCN materials, in the form of solution, powder-pressed pellet and fine powder, were also studied by ultraviolet-visible spectra, four-point probe technique, thermogravimetric analysis (TGA) and scanning electron microscopy (SEM), respectively.     

Preparation of a strong-cation exchange monolith by a novel method and its application in the separation of IgG on high performance liquid chromatography

A strong cation-exchange poly(vinyl carboxylate-co-ethyleneglycol dimethacrylate) (poly(VC-co-EDMA)) monolithic column for high performance liquid chromatography (HPLC) has been prepared firstly by atom transfer radical polymerization (ATRP) without the expensive complexing ligand, in which vinyl carboxylate was used as the monomer, ethyleneglycol dimethacrylate as the cross linking agent, carbon tetrachloride as the initiator and ferrous chloride as the catalyst. Conditions of the polymerization have been studied and optimized. Morphology of monolithic materials was studied by scanning electronic microscopy. Chemical groups of the monolith were assayed by infrared spectra method and the pore size distribution was determined by a mercury porosimeter. Moreover, the monolith was modified to bear strong-cation exchange groups and tested on the separation of human immune globulin G (IgG) from human plasma in conjunction with HPLC. Good resolution was obtained in a short time (10 min) in the separation. The effects of pH and buffer concentration on the elution of IgG have been investigated. Moreover, frontal analytical method was used to get the IgG dynamic banding capacity of the monolith that was 3.0 mg g⁻¹. Besides, the monolith was also used to separate lysozyme from egg white and separate the mixture of papain, snailase and IgG.     

Effect of additives on the initial stage of emulsion polymerization of styrene (St) using poly(vinyl alcohol) as a protective colloid

To realize the mechanism of particle formation followed by the grafting of styrene (St) onto poly(vinyl alcohol) (PVA) more precisely, we investigated the influence of additives on model experiments of emulsion polymerizations in 1 ml styrene (St) per 100 ml water at 70 °C using PVA as a protective colloid. In the case of a standard system without additive, experimental results indicate new particle formation, and that 30% of St feed and 30% of the PVA used were grafted. The sulfate radical seldom enters into particles but reacts with PVA, forming the PVA radical that yields the grafting of St onto PVA. The experimental results are thought to arise from a hydrogen abstraction from PVA with a sulfate radical. The addition of low-molecular-weight alcohol, such as isopropyl alcohol (i-PrOH) and n-propyl alcohol (n-PrOH), strongly affected the mechanism of particle formation in terms of a decrease in grafting, due to competition between hydrogen abstraction from PVA and the alcohols with a sulfate radical. Surprisingly, the addition of a low-reactive alcohol, such as t-butyl alcohol (t-BuOH), also resulted in the particle formation with a decrease in grafting, influenced the polymerization locus to be a monomer droplets dispersed by t-BuOH, and confirmed homogeneous nucleation with the increase in the solubility of St in the aqueous phase.     

Determination of organophosphate and carbamate pesticides based on enzyme inhibition using a pH-sensitive fluorescence probe

A flow injection system for the determination of organophosphate and carbamate pesticides is described. A sensitive fluorescence probe was synthesized and used as the pH indicator to detect the inhibition of the enzyme acetylcholinesterase (AChE). The percentage inhibition of enzyme activity is correlated to the pesticide concentration. Several parameters influencing the performance of the system are discussed. The detection limits of 3.5, 50, 12 and 25 μg/l for carbofuran, carbaryl, paraoxon and dichlorvos, in pure water, respectively were achieved with an incubation time of 10 min. A complete cycle of analysis, including incubation time, took 14 min. The detection system has been applied to the determination of carbofuran in spiked vegetable juices (Chinese cabbage and cole), achieving recovery values between 93.2 and 107% for Chinese cabbage juice and 108 and 118% for cole juice at the different concentration levels assayed.     

Preparation of macroporous functionalized polymer beads by a multistep polymerization and their application in zirconocene catalysts for ethylene polymerization

Macroporous functionalized polymer beads of poly(4‐vinylpyridine‐co‐1,4‐divinylbenzene) [P(VPy‐co‐DVB)] were prepared by a multistep polymerization, including a polystyrene (PS) shape template by emulsifier‐free emulsion polymerization, linear PS seeds by staged template suspension polymerization, and macroporous functionalized polymer beads of P(VPy‐co‐DVB) by multistep seeded polymerization. The polymer beads, having a cellular texture, were made of many small, spherical particles. The bead size was 10–50 μm, and the pore size was 0.1–1.5 μm. The polymer beads were used as supports for zirconocene catalysts in ethylene polymerization. They were very different from traditional polymer supports. The polymer beads could be exfoliated to yield many spherical particles dispersed in the resulting polyethylene particles during ethylene polymerization. The influence of the polymer beads on the catalytic behavior of the supported catalyst and morphology of the resulting polyethylene was investigated. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 873–880, 2003     

Preparation of novel suspensions of ZnO/living block copolymer latex nanoparticles via pickering emulsion polymerization and their long term stability

In this work, we present the first Pickering emulsion polymerization with a controlled/living character. Pickering emulsion polymerization in the presence of a novel suspension of zinc oxide/poly(sodium 4‐styrenesulfonate) (ZnO/PSS^?) nanocomposite particles was applied to prepare ZnO/living block copolymer latexes. In the emulsion system, 1,1‐diphenylethene (DPE)‐controlled radical polymerization of poly(methyl methacrylate)‐b‐poly(butyl acrylate) (PMMA‐b‐PBA) was proceeded in oil phase. The nanocomposite particles of ZnO/PSS^? with an average diameter of 20 nm and negatively charged zeta potential around ?30 mV were synthesized via hydrothermal method then served as an effective emulsion stabilizer at the oil/water interface. Living polymerization was carried out using DPE‐capped PMMA as the macroinitiator and PMMA‐b‐PBA block copolymer latex was successfully prepared with coverage of ZnO/PSS^? nanoparticles. Narrow size distributions of the droplets as well as latex particles were obtained, and the livingness of block copolymers was comparable to that of emulsions stabilized by conventional surfactants. The controlled/living character in Pickering emulsion polymerization was slightly influenced by the amount of PSS^? immobilized into the ZnO/PSS^? nanoparticles, whereas it was significantly influenced by the weight ratios between ZnO/PSS^? and oil phase. The Pickering latexes showed excellent long term stability against either coalescence or sedimentation over several months. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Influence of additives on model emulsion polymerization of vinyl acetate (VAc) using poly(vinyl alcohol) (PVA) as a protective colloid

To clarify the influence of additives on the grafting phenomenon as well as the particle behavior more precisely, we carried out a model emulsion polymerization of vinyl acetate (VAc) in a 1% aqueous solution with ammonium persulfate (APS) using poly (vinyl alcohol) (PVA) as a protective colloid in the presence of additives. The addition of alcohol to the system remarkably affected the particle formation, especially grafting. This is thought to be attributed to competition between hydrogen abstraction from PVA and alcohol with a sulfate radical. Especially, the addition of acetone to the system decreased grafting to a great extent, resulting in an increase in the particle size together with an increase in the number of polymer molecules in a polymer particle. This result is thought to arise from a combination of electron abstraction from acetone with a sulfate radical and the chain-transfer reaction of the propagation radical with acetone.     

新型磁性分子印迹聚合物的制备及其在氟喹诺酮类抗生素检测中的应用

建立了磁性分子印迹聚合物固相萃取与高效液相色谱联用同时检测环境水中4种氟喹诺酮类抗生素的研究方法。分别利用扫描电子显微镜、透射电子显微镜、X-射线衍射、傅里叶红外光谱、振动样品磁强计对合成的磁性分子印迹聚合物进行表征,对影响吸附实验的参数（包括吸附剂用量、吸附和解析时间、洗脱液种类、样品pH值）进行了考察和优化。在最佳的实验条件下,4种氟喹诺酮类抗生素的方法检出限为4.1~21.3 μg/L,方法定量限为13.7~71.0 μg/L,样品加标回收率为70.6%~103.6%。该方法快速、灵敏,能够满足环境水样中氟喹诺酮类抗生素的残留检测要求。     

Preparation of poly(methyl methacrylate)/CaCO3/SiO2 composite particles via emulsion polymerization

A novel method to prepare organic/inorganic composite particles, i.e. poly(methyl methacrylate)/CaCO₃/SiO₂ three-component composite particles, using emulsion polymerization of methyl methacrylate with sodium lauryl sulfate as a surfactant in an aqueous medium was reported. CaCO₃/SiO₂ two-component inorganic composite particles were obtained firstly by the reaction between Na₂CO₃ and CaCl₂ in porous silica (submicrometer size) aqueous sol and the specific surface area of the particles was measured by the Brunauer–Emmett–Teller (BET) method. The results show that the BET specific surface area of the CaCO₃/SiO₂ composite particle is much smaller than that of the silica particle, indicating that CaCO₃ particles were adsorbed by porous silica and that two-component inorganic composite particles were formed. Before copolymerization with methyl methacrylate, the inorganic composite particles were coated with a modifying agent through covalent attachment. The chemical structures of the poly(methyl methacrylate)/CaCO₃/SiO₂ composite particles obtained were characterized by Fourier transform IR spectroscopy and thermogravimetric analysis. The results show that the surface of the modified inorganic particles is grafted by the methyl methacrylate molecules and that the grafting percentage is about 15.2%.